I19Z60740-SEM01_SAR_Rev3_part3

FCC ID: ZNFX120HM

RF Exposure Info

Download: PDF
FCCID_4335885

TTL F V Calibration t Laboratory of . Schweizerischer Kalibrierdienst Schm[d & Partner ; Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S swiss Catibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates References [1] ANSi—Cé3.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: * Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. in coincidence with the standards [1], the measurement planes (probe sensorcenter) are selected to be at a distance of 15 mm above thetop metal edge of thedipole arms. * Measurement Conditions: Further details are available from the hardcopiesat the end of the certificate. All figures stated in the certificate are valid at the frequencyindicated. The forward powerto the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While thedipole under test is connected, the forward power is adjusted to the same level. * Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its armsare perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probeis adjusted after dipole mounting with a DASY5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distanceis selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distanceto the probe is essential for the accuracy. * Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of thedipole. The influenceof reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. * E—field distribution: E field is measured in the x—y—plane with an isotropic ERSD—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan areais 20mm wide, its length exceeds the dipole arm length (180 or 9Omm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of thedipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima(in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD835V3—1023_Aug18 Page 2 of 5

© Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version Phantom Distance Dipole Top — Probe Center DASY5 HAC Test Arch 15 mm V52.10.1 Scan resolution dx, dy = 5 mm Frequency 835 MHz +1 MHz Input power drift <0.05 dB Maximum Field values at 835 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 111.0 V/im=40.91 dBV/m Maximum measured above low end 100 mW input power 109.6 V/m = 40.80 dBV/m Averaged maximum above arm 100 mW input power 110.3 V/im £ 12.8 % (k=2) Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters Frequency Return Loss Impedance 800 MHz 18.1 dB 42.6 0 — 9.0 jQ 835 MHz 23.3 dB 53.6 Q + 6.1 jQ 880 MHz 15.6 dB 65.0 Q — 11.8 jQ 900 MHz 17.7 dB 53.6 Q — 13.1 jQ 945 MHz 25.0 dB 46.5 Q + 4.1 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD835V3—1023_Aug18 Page 3 of 5 ~o~ use > —

© Impedance Measurement Plot File Yiew Channel Sweep Calbration Trace Scale Marker System Window Help 10.00 800.000000 MHz —18.052 0B 3500000 Mss 23 283 40 5.00 820.000000 MHz ~15.635 0B 0.00 5.00 c 77 Ramee & sds 25 NALdR F10.00 F15.00 F20.00 L25.00 30.00 35.00 L40 .00 Ch 1 Avg= |20 Ch1: Start 335.000 MHz —— Stop 1.33500 GHz 1: 800.000000 MHz 42614 0 22.098 pF —3.0028 >20 $35.000000 MHz 53.633 0 1.1658nH 8.1164 0 3: 880.000000 MHz 64.993 0 15.268 pF 1.846 0 4: 900.000000 MHz 53.610 2 13.516 pF 13.084 0 5: $45.000000 MHz 46 466 689.85 pH 4.0961 A Ch1Avg= 20 Chi: Start 335.000 MHe —— Stop 1.33500 GHz Status CH 1: C" 1—Port Avg=20 Delay LCL Certificate No: CD835V3—1023_Aug18 Page 4 of 5 ~o~ ucce > —

DASY5 E—field Result Date: 28.08.2018 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1023 Communication System: UID 0 — CW ; Frequency: 835 MHz Medium parameters used: 0 = 0 $/m, & = 1; p = 0 kg/m? Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19 —2011) DASY52 Configuration: * Probe: EF3DV3 — SN4013; ConvF(1, 1, 1) @ 835 MHz; Calibrated: 05.03.2018 e Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 17.01.2018 * Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole E—Field measurement @ 835MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 132.3 V/m; Power Drift =—0.03 dB Applied MIF = 0.00 dB RF audio interference level = 40.91 dBV/m Emission category: M3 MIF scaled E—field Grid 1 M3 Grid 2 M3 Grid 3 M3 40.37 dBV/m 40.8 dBV/m 140.73 dBV/m Grid 4 M4 Grid 6 M4 35.58 dBV/m 35.91 dBV/m Grid 7 M3 Grid 8 M3 Grid 9 M3 40.56 dBV/m 40.91 dBV/m |40.85 dBV/m —1.94 ~3.89 5.83 —7.18 .72 0 dB = 111.0 V/m = 40.91 dBV/m Certificate No: CD835V3—1023_Aug18 Page 5 of 5 ~oo c ucce >

e F M al199y Callbll'atlon Laboratory of i\\\‘&///’z} g Schweizerischer Kalibrierdienst Schmid & Partner M c Service suisse d‘étalonnage Engmeerlng AG gre Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland "/,,/’///I\\\‘\\\\? S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client CTTL (Auden) Certificate No: D1750V2—1003_Jul18 CALIBRATION CERTIFICATE Object D1750V2 — SN:1003 Calibration procedure(s) QA CAL—05.v10 Calibration procedure for dipole validation kits above 700 MHz Calibration date: July 20, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 7349 30—Dec—17 (No. EX3—7349_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician + Approved by: Katia Pokovic Technical Manager %g Issued: July 20, 2018 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: D1750V2—1003_Jul18 Page 1 of 8 wenvperg n rage en

oo — . ; w1 10e, callb'.'atlon Laboratory of s\“\\\_//\//"/,; S Schweizerischer Kalibrierdienst Schmid & Partner M c Service suisse d‘étalonnage Engineering AG 2y Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland é/,,/7/\\\\‘\\3 S Swiss Calibration Service "thiluls Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1750V2—1003_Jul18 Page 2 of 8 snn vrpery n ragbee e wb n ngn nvar n nenever e mene meg n sn e

(llém’ w Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1750 MHz &1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.1 1.37 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 39.0 26 % 1.34 mho/m £ 6 % Head TSL temperature change during test x0.5°C ==~= SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 8.91 W/kg SAR for nominal Head TSL parameters normalized to 1W 35.9 W/kg x 17.0 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 4.71 Wikg .SAR for nominal Head TSL parameters normalized to 1W 18.9 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.4 1.49 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 53.7 #6 % 1.46 mho/m £ 6 % Body TSL temperature change during test <0.5 °C ——— SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 8.97 W/kg SAR for nominal Body TSL parameters normalized to 1W 36.4 Wikg 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 4.79 Wikg SAR for nominal Body TSL parameters normalized to 1W 19.3 Wikg * 16.5 % (k=2) Certificate No: D1750V2—1003_Jul18 Page 3 of 8 Nes sperg n ragi esn n en n ege ie n e > >

()< Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point . Return Loss 51.6 Q + 1.3 jQ — 33.7 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 47.3 Q + 1.2 jQ Return Loss — 30.4 dB General Antenna Parameters and Design LElectrica[ Delay (one direction) J 1.215 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by * SPEAG Manufactured on July 30, 2008 Certificate No: D1750V2—1003_Jul18 Page 4 of 8 Nnpeg n en n n n nge e c n >

DASY5 Validation Report for Head TSL Date: 20.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN:1003 Communication System: UID 0 — CW; Frequency: 1750 MHz Medium parameters used: f = 1750 MHz; 0 = 1.34 S/m; & = 39; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(8.5, 8.5, 8.5) @ 1750 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 & Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.5 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 16.3 W/kg SAR(1 g) = 8.91 W/kg; SAR(10 g) = 4.71 W/kg Maximum value of SAR (measured) = 13.8 W/kg dB 0 ~4.00 —8.00 —12.00 —16.00 —20.00 0 dB = 13.8 W/kg = 11.40 dBW/kg Certificate No: D1750V2—1003_Jul18 Page 5 of 8 Nn en n n en n n n n e n n n n n ey >

Impedance Measurement Plot for Head TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 1.750000 GHz 51.596 O 122.55 pH 13475 Q 1.750000 GHz 20.559 mU $\ 39.410 ° Ch1Aug= 20 Chi: Start 1.55000 GHz —— Stop 1.95000 GHz —3$.740 dB 00 00 00 00 f Ch 1 Aug= Ch1: Start 155000 GHz —— Stop 1.95000 GHz Status CH 1: Avg=20 Delay Certificate No: D1750V2—1003_Jul18 Page 6 of 8 Nn opeg n n n n n c ++ >

DASY5 Validation Report for Body TSL Date: 20.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN:1003 Communication System: UID 0 — CW; Frequency: 1750 MHz Medium parameters used: f = 1750 MHz; 0 = 1.46 $/m; &, = 53.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(8.35, 8.35, 8.35) @ 1750 MHz; Calibrated: 30.12.2017 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 26.10.2017 & Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 101.3 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 15.7 W/kg SAR(1 g) = 8.97 W/kg; SAR(10 g) = 4.79 W/kg Maximum value of SAR (measured) = 13.5 W/kg dB 0 ~4.00 —8.00 —12.00 —16.00 —20.00 0 dB = 13.5 W/kg = 11.30 dBW/kg Certificate No: D1750V2—1003_Jul18 Page 7 of 8 Nennmua nn n n e n h on n n > —

Impedance Measurement Plot for Body TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 1.750000 GHz 47.338 Q 112.37 pH 1.2356 Q 1.750000 GHz 30.149 mU 154.37 ° Ch1Avg= 20 Chi: Start 1.55000 GHz Stop 1.95000 GHz .00 00 00 00 00 Ch1: Start 1 Stop 1.95000 GHz CH 1: Avg=20 Delay Certificate No: D1750V2—1003_Jul18 Page 8 of 8 ~mivmuan n nc c e c on ns

s x w1 o Callbfatlon Laboratory of s‘\\\\__///’z} S Schweizerischer Kalibrierdienst Schm[d & F_’artner ila\eg/mf_ c Service suisse d‘étalonnage Engmeerlng AG . re Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,///A\\\\? S Swiss Calibration Service Ahilals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client CTTL (Auden) Certificate No: D1900V2—5d101_Jul18 CALIBRATION CERTIFICATE Object D1900V2 — SN:5d101 Calibration procedure(s) QA CAL—O05.v10 Calibration procedure for dipole validation kits above 700 MHz Calibration date: July 24, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 108244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z291 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06827 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 7349 30—Dec—17 (No. EX3—7349_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37292783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician Approved by: Katia Pokovic Technical Manager M Issued: July 24, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D1900V2—5d101_Jul18 Page 1 of 8 Ns eperg n sn in n me n n n e n e e n en y e >

. s yln1 pg, callbratlon Laboratory of i\\\&////'/’; g Schweizerischer Kalibrierdienst Schmid & Partner ;Ia\ez—/m c Service suisse d‘étalonnage Englneerlng AG 3. ~sang Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,, 7;\? \\\3 S Swiss Calibration Service "thiluls Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1900V2—5d101_Jul18 Page 2 of 8 Nes veperg n ragr en n en n mgmene n mm en n en e e c n >

m_" ‘/"/"/, oo — Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1900 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 39.9 £ 6 % 1.34 mho/m # 6 % Head TSL temperature change during test <0.5 °C ——— SAR result with Head TSL SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 9.84 Wikg SAR for nominal Head TSL parameters normalized to 1W 40.4 Wikg x 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 5.23 W/kg SAR for nominal Head TSL parameters normalized to 1W 21.3 W/kg #16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 54.3 £6 % 1.46 mho/m + 6 % Body TSL temperature change during test <0.5 °C _ wee— SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 9.83 W/kg SAR for nominal Body TSL parameters normalized to 1W 40.4 Wikg x 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured . 250 mW input power 5.26 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg x 16.5 % (k=2) Certificate No: D1900V2—5d101_Jul18 Page 3 of 8 wer n vpery n rage bee nb n rign newr in cevever n nevr weg n n e e

a=777 ul Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 50.7 Q + 5.3 jQ Return Loss —25.6 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 44.9 Q + 6.5 JQ Return Loss —21.2 dB General Antenna Parameters and Design rElectfical Delay (one direction) 1.205 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on March 28, 2008 Certificate No: D1900V2—5d101_Jul18 Page 4 of 8 Ne n veperg n rag en e mb n ng eene n nene se n en meg n nc

DASY5 Validation Report for Head TSL Date: 24.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN:5d101 Communication System: UID 0 — CW; Frequency: 1900 MHz Medium parameters used: f = 1900 MHz; 0 = 1.34 S/m; & = 39.9; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(8.18, 8.18, 8.18) @ 1900 MHz; Calibrated: 30.12.2017 Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 26.10.2017 Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 110.6 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 17.9 W/kg SAR(1 g) = 9.84 W/kg; SAR(10 g) = 5.23 W/kg Maximum value of SAR (measured) = 15.0 W/kg 12.00 —16.00 —20.00 0 dB = 15.0 W/kg = 11.76 dBW/kg Certificate No: D1900V2—5d101_Jul18 Page 5 of 8 w vrvperg n rgesn n n rge revr n venver e nene meg n +s


Document Created: 2019-06-26 15:02:49
Document Modified: 2019-06-26 15:02:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC