I19Z60741-SEM01_SAR_Rev0_part2

FCC ID: ZNFX120EMW

RF Exposure Info

Download: PDF
FCCID_4337811

EX3DV4— SN:7514 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Une (k=2) Norm (uV/(V/im)")"* 0.46 0.44 0.39 *10.1% DCP (mV)" 96.5 101.1 97.9 Modulation Calibration Parameters UID Communication System Name A B 8 D VR Unc® dB dByuV dB mV (k=2) 0 CW X 0.0 0.0 1.0 0.00 179.1 23.5 % Y 0.0 0.0 1.0 177.3 Z 0.0 0.0 1.0 158.1 Note: For details on UID parameters see Appendix. Sensor Model Parameters C1 C2 a T1 T2 T3 T4 TS T6 fF fF VZ ms.V~* ms.V~‘ ms V~ V X 31.17 241.1 27.77 3.625 0.025 5.031 0.000 325 1.005 Y 34.86 259.7 35.41 7412 0.000 5.026 0.323 0.291 1.002 Z 33.14 259.6 38.65 3.827 0,264 5.046 0.000 0.373 1.008 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,2Z do not affectthe E*—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. © Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square ofthe field value. Certificate No: EX3—7514_Aug18 Page 4 of 39

EX3DV4— SN:7514 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth ° Une f(MHz)* Permittivity" (S/m)" ConvFX ConvFY ConvFZ Alpha® _{mm) (k=2) 150 523 0.76 12.79 12.79 12.79 0.00 1.00 13.3 % 300 45.3 0.87 11.57 11.57 11.57 0.07 1.20 *183% 450 438 0.87 10.68 10.68 10.68 0.14 1.20 +13.3% 750 41.9 0.89 9.47 9.47 9.47 0.45 0.89 £*12.0% 835 41.5 0.90 9.09 9.09 9.09 0.53 0.85 + 12.0 % 900 41.5 0.97 9.03 9.03 9.03 0.49 0.85 +12.0 % 1450 40.5 1.20 8.24 8.24 8.24 0.35 0.80 +12.0 % 1640 40.2 1.31 8.22 8.22 8.22 0.38 0.81 +12.0 % 1750 40.1 1.37 8.10 8.10 8.10 0.36 0.83 * 12.0 % 1810 40.0 1.40 7.82 7.82 7.82 0.35 0.81 * 12.0 % 1900 40.0 1.40 7.73 173 773 0.31 0.80 * 12.0 % 2000 40.0 1.40 7.64 7.64 7.64 0.30 0.84 *12.0 % 2100 39.8 1.49 7.57 7.57 7.57 0.27 0.85 +120 % 2300 39.5 1.67 742 7.42 7.42 0.31 0.80 +12.0% 2450 39.2 1.80 6.95 6.95 6.95 0.38 0.98 +120 % 2600 39.0 1.96 6.92 6.92 6.92 0.25 1.05 *12.0 % 3500 37.9 2.91 6.78 6.78 6.78 0.79 0.64 #13.1% 3700 37.7 3.12 6.61 6.61 6.61 0.42 0.93 £13.1% 5200 36.0 4.66 5.05 5.05 5.05 0.40 1.80 *13.1 % 5250 35.9 4.71 5.02 5.02 5.02 0.40 1.80 * 13.1 % 5300 35.9 4.76 4.99 4.99 4.99 0.40 1.80 *13.1 % 5500 $5.6 4.96 4.59 4.59 4.59 0.40 1.80 #18.1 % 5600 355 5.07 4.41 4.41 4.41 0.40 1.80 *13.1 % 5750 35.4 5.22 447 4.47 4.47 0.40 1.80 *13.1 % 5800 35.3 5.27 442 4.42 4.42 0.40 1.80 +131 % © Frequency validity above 300 MHz of x 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for theindicated frequency band. Frequencyvalidity below at 150 MHz is + 50 MHz. Above 5 GHz frequency validity can be extended to £ 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (e and a)can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (c and a) is restricted to * 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—7514_Aug18 Page 5 of 39

EX3DV4— SN:7514 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth ° Une f(MHz)* Permittivity" (S/m)" ConvFX ConvFY ConvFZ Aipha® _{mm) (k=2) 150 61.9 0.80 1243 1243 1243 0.00 1.00 *13.3 % 300 58.2 0.92 11.39 11.39 11.39 0.05 1.20 *13.3 % 450 56.7 0.94 11.34 11.34 11.34 0.08 1.20 13.3 % 750 55.5 0.96 9.68 9.68 9.68 0.31 1.04 +12.0 % 835 55.2 0.97 9.47 9.47 9.47 0.46 0.80 * 12.0 % 900 55.0 1.05 9.34 9.34 9.34 0.46 0.83 * 12.0 % 1450 54.0 1.30 8.02 8.02 8.02 0.31 0.80 *12.0 % 1640 53.7 1.42 7.85 7.85 7.85 0.42 0.81 + 12.0 % 1750 53.4 1.49 7.82 7.82 7.82 0.39 0.83 * 12.0 % 1810 53.3 1.52 7.69 7.69 7.69 0.32 0.92 *12.0 % 1900 53.3 1.52 T83 7.53 +83 0.35 0.83 * 12.0 % 2000 $83 1.52 7.45 745 745 0.39 0.80 * 12.0 % 2100 53.2 1.62 7.39 7.39 7.39 0.32 0.94 * 12.0 % 2300 52.9 1.81 7.25 725 7.25 0.37 0.85 +12.0 % 2450 52.7 1.95 713 713 7A3 0.32 0.97 +12.0 % 2600 52.5 216 7.06 7.06 7.06 0.24 1.10 +12.0 % 3500 51.3 3.31 6.85 6.85 6.85 0.00 1.00 £13.1 % 3700 51.0 3.55 6.75 6.75 6.75 0.00 1.00 #13.1 % 5200 49.0 5.30 4.59 4.59 4.59 0.50 1.90 *13.1 % 5250 48.9 5.36 4.54 4.54 4.54 0.50 1.90 #13.1 % 5300 48.9 5.42 449 4.49 4.49 0.50 1.90 £13.1% 5500 48.6 5.65 4.A17 4.17 4.17 0.50 1.90 #13.1% 5600 48.5 .77 4.00 4.00 4.00 0.50 1.90 *13.1 % 5750 48.3 5.94 3.98 3.98 3.98 0.50 1.90 #13.1 % 5800 48.2 6.00 3.94 3.94 3.94 0.50 1.90 *13.1% © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below at 150 MHzis + 50 MHz. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (e and 0) is restricted to + 5%. The uncertainty is the RSS of the ConyF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameterfrom the boundary. Certificate No: EX3—7514_Aug18 Page 6 of 39

EXSDV4— SN:7514 August 27, 2018 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) TTTTTTT 14 18 Frequency response (normalized) T RESEmmT 1.2 as % 1 s o 1 DG —|o nrmeemnsconccemedescnsscne BW ccccsrcssccsrscereed or—L— D@—frmmmmmiss 05 L _1 t i 1000 Te Uncertainty of Frequency Response of E—field: * 6.3% (k=2) Certificate No: EX3—7514_Aug18 Page 7 of 39

(I%I) EX3DV4— SN:7514 August 27, 2018 Receiving Pattern (¢), 8 = 0° f=600 MHz,TEM £=1800 MHz,R22 ~so 1357 % a5 f ¥——. y ¥ecg > ; * + ++ ¢ + + . x} 9+ 0+ 204 180. f g + 180 + * toz o« og"os + + * % + *—t.—* ; t — x « — + + + & f s « /A 4 * + * 1 s—.4.—* 4——* a P 225 #+4 sis 225 tsz ue Bs ty 27 370 ® € e Nj.l * * ® LA Tot X Y Tot X Y £ Error [dB] sg § e 18WHZ 2500 MHz Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—7514_Aug18 Page 8 of 39

EXSDV4— SN:7514 August 27, 2018 Dynamic Range f(SARpeaq) (TEM cell , fey;= 1900 MHz) Input Signal [uV) 108 102 107 10° 101 10 10 SAR [mW/iem3] not compensated compensated Error [dB] 109 102 101 100 10 102 103 SAR [mW/cm3] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—7514_Aug18 Page 9 of 39

) «@7"7] | EX3DV4— SN:7514 August 27, 2018 Conversion Factor Assessment £= 900 MHz,WGLS R9 (H_convF) 1= 1810 MHz,WGLS R22 (H_convF) 40 | 30— 35 i |‘ 7'.. 25 (.. 30— '.__. | [ ._. . t % x * ‘g- ZD‘ g 15‘ 15 I t ‘011 10 Y D s| * *~ as * "r > oo A 1. 1 bopiecet § L tce pokabe tpat ko oys pitoe t 3u5ekccnatuy i . 0 5 10 1 2 28 % 5 40 0 10 1 2 ES 35 40 2 {mm] 2 {mm] * *) —+. anabtcal measured anabtical measured Deviation from Isotropy in Liquid Error (¢, 8), f = 900 MHz Deviation —1.0 —0.8 —0.6 —0.4 —0.2 0.0 02 04 0.6 08 1.0 Uncertainty of Spherical Isotropy Assessment: * 2.6% (k=2) Certificate No: EX3—7514_Aug18 Page 10 of 39

G) 4N EX3DV4— SN:7514 August 27, 2018 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7514 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) ~19.8 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—7514_Aug18 Page 11 of 39

No. I19Z60741-SEM01 Page 114 of 146 ANNEX H Dipole Calibration Certificate 835 MHz Dipole Calibration Certificate ©Copyright. All rights reserved byCTTL.

<II§II\! Calibration £ Laboratory of wl/mL gs1LZ S Schweizerischer Kalibrierdienst Schmid & Partner ila\E'—%& c Service suisse d‘étalonnage Engineering AG cz or, Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland *,fi\y S swiss Calibration Service "thilube Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D835V2—4d069_Jul18 Page 2 of 8

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 835 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 £0.2) °C 40.7 26 % 0.92 mho/m 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.40 W/ikg SAR for nominal Head TSL parameters normalized to 1W 9.40 Wikg # 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 1.54 Wikg SAR for nominal Head TSL parameters normalized to 1W 6.06 W/kg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.2 0.97 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 55.2 + 6 % 0.99 mho/m +6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 2.42 W/kg SAR for nominal Body TSL parameters normalized to 1W 9.53 Wikg # 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 1.59 Wikg SAR for nominal Body TSL parameters normalized to 1W 6.28 Wikg x 16.5 % (k=2) Certificate No: D835V2—40069_Jul18 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 50.8 Q — 2.1 jQ Return Loss — 33.0 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 46.1 Q — 5.2 jQ Return Loss —23.4 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.396 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on November 09, 2007 Certificate No: D835V2—40069_Jul18 Page 4 of 8

m_ /7/ . ~* DASY5 Validation Report for Head TSL Date: 16.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:4d069 Communication System: UID 0 — CW; Frequency: 835 MHz Medium parameters used: £ = 835 MHz; 0 = 0.92 $/m; & = 40.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(9.9, 9.9, 9.9) @ 835 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 & Phantom: Flat Phantom 4.9 (front); Type: QD OOL P49 AA; Serial: 1001 + DASY32 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value = 62.65 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 3.70 W/kg SAR(1 g) = 2.4 W/ikg; SAR(10 g) = 1.54 W/kg Maximum value of SAR (measured) =3.25 W/kg dB 0 —2.00 —4.00 —6.00 —8.00 —10.00 0 dB = 3.25 W/kg = 5.12 dBW/kg Certificate No: D835V2—40069_Jul18 Page 5 of 8

Impedance Measurement Plot for Head TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 835.000000 MHz 50.789 0 90.520 pF —2.1057 Q 35.000000 MHz 22.306 mU —68.254 ° ChiAug= 20 Chi: Start €35,000 MHz Stop 1.03500 GHz 00 00 00 35.00 o 1 & Ch1: Start £35.000 MHz Stop 1.03500 GHz Status CH 1: E‘H IC“1-Port Avg=20 Delay LCL Certificate No: D835V2—40069_Jul18 Page 6 of 8

mm ‘/"/‘L ~ DASY5 Validation Report for Body TSL Date: 23.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:40069 Communication System: UID 0 — CW; Frequency: 835 MHz Medium parameters used: f = 835 MHz; 0 = 0.99 S/m; & = 55.2; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(10.05, 10.05, 10.05) @ 835 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 + Phantom: Flat Phantom 4.9 (Back); Type: QD OOR P49 AA; Serial: 1005 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 60.75 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 3.59 W/kg SAR(1 g) = 2.42 W/kg; SAR(10 g) = 1.59 W/kg Maximum value of SAR (measured) = 3.22 W/kg 0 dB = 3.22 W/kg = 5.08 dBW/kg Certificate No: D835V2—40069_Jul18 Page 7 of 8

Impedance Measurement Plot for Body TSL File View Channel Sweep Calbration Trace Scale Marker System Window Help 46.118 O —5£1978 0 67.394 mU ~123.56 ° Ch1Aug= 20 Ch1: Start §35.000 MHz —— Stop 1.03500 GHz 835.000000 —2$.428 dB o0 Ch 1 = Ch1: Start €35.000 MHe ——— Status CH 1: 511 | C*1—Port Avg=20 Delay LCL Certificate No: D835V2—4d0069_Jul18 Page 8 of 8

s 3 «o ca"bratlon Laboratory of S\‘\\\\///’z} S Schweizerischer Kalibrierdienst Schmid & Partner M c Service suisse d‘étalonnage Englneerlng AG * sg Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland f'/,,Afi\“\? S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client CTTL (Auden) Certificate No: D1900V2—5d101_Jul18 CALIBRATION CERTIFICATE Object D1900V2 — SN:5d101 Calibration procedure(s) QA CAL—05.v10 Calibration procedure for dipole validation kits above 700 MHz Calibration date: July 24, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z291 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 7349 30—Dec—17 (No. EX3—7349_Dec17) Dec—18 DAE4 SN: 601 26—Oct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician Approved by: Katja Pokovic Technical Manager /C,/@ Issued: July 24, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D1900V2—5d101_Jul18 Page 1 of 8


Document Created: 2019-06-27 14:15:22
Document Modified: 2019-06-27 14:15:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC