SAR Report

FCC ID: ZNFW200V

RF Exposure Info

Download: PDF

FCCID_2770793

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

Revision History
Rev. Date Revisions Revised By
V1 9/28/2015 Initial Issue --
V2 9/30/2015 Report revised based on Reviewer’s comments: Kenneth Mak
1. Added Section 6.4.
2. Appendix A: Updated

Page 2 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

Table of Contents

1. Attestation of Test Results ......................................................................................................... 5

2. Test Specification, Methods and Procedures............................................................................ 6

3. Facilities and Accreditation ........................................................................................................ 6

4. SAR Measurement System & Test Equipment .......................................................................... 7
4.1. SAR Measurement System ........................................................................................................ 7
4.2. SAR Scan Procedures ............................................................................................................... 8
4.3. Test Equipment........................................................................................................................ 10

5. Measurement Uncertainty ......................................................................................................... 11

6. Device Under Test (DUT) Information ...................................................................................... 12
6.1. DUT Description ...................................................................................................................... 12
6.2. Wireless Technologies ............................................................................................................. 12
6.3. Nominal and Maximum Output Power from Tune-up Procedure .............................................. 13
6.4. Antenna Dimensions and Separation Distances ...................................................................... 13
6.5. General LTE SAR Test and Reporting Considerations............................................................. 14

7. RF Exposure Conditions (Test Configurations) ...................................................................... 14

8. Dielectric Property Measurements & System Check .............................................................. 15
8.1. Dielectric Property Measurements ........................................................................................... 15
8.2. System Check.......................................................................................................................... 17

9. Conducted Output Power Measurements................................................................................ 19
9.1. LTE .......................................................................................................................................... 19
9.2. Wi-Fi 2.4GHz (DTS Band) ....................................................................................................... 21
9.3. Bluetooth ................................................................................................................................. 21

10. Measured and Reported (Scaled) SAR Results ....................................................................... 22
10.1. LTE Band 13 (10MHz Bandwidth) ........................................................................................ 24
10.2. Wi-Fi (DTS Band) ................................................................................................................. 24
10.3. Standalone SAR Test Exclusion Considerations & Estimated SAR ...................................... 25

11. SAR Measurement Variability ................................................................................................... 26

12. Simultaneous Transmission SAR Analysis ............................................................................. 27
12.1. Sum of the SAR for WWAN & Wi-Fi & BT (Extremity) .......................................................... 27
12.2. Sum of the SAR for WWAN & Wi-Fi & BT (Next-to-Mouth) ................................................... 27

Appendixes .......................................................................................................................................... 28
15I21799-S1V2 SAR_App A Photos & Ant. Locations (STC_180days) .............................................. 28
Page 3 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

2. Test Specification, Methods and Procedures
The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE STD 1528-
2013, the following FCC Published RF exposure KDB procedures:
o 248227 D01 802.11 Wi-Fi SAR v02r01
o 447498 D01 General RF Exposure Guidance v05r02
o 447498 D03 Supplement C Cross-Reference v01
o 690783 D01 SAR Listings on Grants v01r03
o 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04
o 865664 D02 RF Exposure Reporting v01r01
o 941225 D05 SAR for LTE Devices v02r03

3. Facilities and Accreditation
The test sites and measurement facilities used to collect data are located at

47173 Benicia Street 47266 Benicia Street
SAR Lab A SAR Lab 1
SAR Lab B SAR Lab 2
SAR Lab C SAR Lab 3
SAR Lab D SAR Lab 4
SAR Lab E SAR Lab 5
SAR Lab F
SAR Lab G
SAR Lab H

UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0.

Page 6 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

5. Measurement Uncertainty
Per KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz, when the highest measured 1-g SAR within a
frequency band is < 1.5 W/kg, the extensive SAR measurement uncertainty analysis described in IEEE Std 1528-
2013 is not required in SAR reports submitted for equipment approval.

Page 11 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

6.3. Nominal and Maximum Output Power from Tune-up Procedure
KDB 447498 sec.4.1.(3) at the maximum rated output power and within the tune-up tolerance range specified for
the product, but not more than 2 dB lower than the maximum tune-up tolerance limit

Upper limit (dB): -1.5 ~ 0.5 Max. RF Output Pow er (dBm)
Max. tune-up
RF Air interface Mode Target
tolerance limit
QPSK 23.2 23.7
LTE Band 13
16QAM 22.2 22.7
Upper limit (dB): 1.0 Max. RF Output Pow er (dBm)
Max. tune-up
RF Air interface Mode Target
tolerance limit
802.11b 16.5 17.5
WiFi 2.4 GHz 802.11g 12.5 13.5
802.11n HT20 11.5 12.5
Bluetooth 9.5 10.5
Bluetooth LE 8.0 9.0

6.4. Antenna Dimensions and Separation Distances
Refer to separate filing document.

Page 13 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

8. Dielectric Property Measurements & System Check
8.1. Dielectric Property Measurements
The temperature of the tissue-equivalent medium used during measurement must also be within 18C to 25C and
within ± 2C of the temperature when the tissue parameters are characterized.
The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR
measurements. The parameters should be re-measured after each 3 – 4 days of use; or earlier if the dielectric
parameters can become out of tolerance; for example, when the parameters are marginal at the beginning of the
measurement series.
Tissue dielectric parameters were measured at the low, middle and high frequency of each operating frequency
range of the test device.

Tissue Dielectric Parameters
FCC KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz
Head Body
Target Frequency (MHz)
er s (S/m) er s (S/m)
150 52.3 0.76 61.9 0.80
300 45.3 0.87 58.2 0.92
450 43.5 0.87 56.7 0.94
835 41.5 0.90 55.2 0.97
900 41.5 0.97 55.0 1.05
915 41.5 0.98 55.0 1.06
1450 40.5 1.20 54.0 1.30
1610 40.3 1.29 53.8 1.40
1800 – 2000 40.0 1.40 53.3 1.52
2450 39.2 1.80 52.7 1.95
3000 38.5 2.40 52.0 2.73
5000 36.2 4.45 49.3 5.07
5100 36.1 4.55 49.1 5.18
5200 36.0 4.66 49.0 5.30
5300 35.9 4.76 48.9 5.42
5400 35.8 4.86 48.7 5.53
5500 35.6 4.96 48.6 5.65
5600 35.5 5.07 48.5 5.77
5700 35.4 5.17 48.3 5.88
5800 35.3 5.27 48.2 6.00

IEEE Std 1528-2013
Refer to Table 3 within the IEEE Std 1528-2013

Page 15 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015
Dielectric Property Measurements Results:

SAR Lab A
Date Freq. (MHz) Liquid Parameters Measured Target Delta (%) Limit ±(%)
e' 39.1300 Relative Permittivity (єr): 39.13 39.20 -0.18 5
Head 2450
e" 13.7800 Conductivity (σ): 1.88 1.80 4.29 5
e' 39.2600 Relative Permittivity (єr): 39.26 39.28 -0.05 5
9/18/2015 Head 2410
e" 13.6900 Conductivity (σ): 1.83 1.76 4.21 5
e' 39.0400 Relative Permittivity (єr): 39.04 39.17 -0.33 5
Head 2475
e" 13.8300 Conductivity (σ): 1.90 1.83 4.17 5
e' 51.8200 Relative Permittivity (єr): 51.82 52.70 -1.67 5
Body 2450
e" 14.8900 Conductivity (σ): 2.03 1.95 4.02 5
e' 51.9200 Relative Permittivity (єr): 51.92 52.76 -1.59 5
9/18/2015 Body 2410
e" 14.8000 Conductivity (σ): 1.98 1.91 3.97 5
e' 51.7500 Relative Permittivity (єr): 51.75 52.67 -1.74 5
Body 2475
e" 14.9400 Conductivity (σ): 2.06 1.99 3.57 5

SAR Lab B
Date Freq. (MHz) Liquid Parameters Measured Target Delta (%) Limit ±(%)
e' 54.3100 Relative Permittivity (єr): 54.31 55.55 -2.23 5
Body 750
e" 23.3000 Conductivity (σ): 0.97 0.96 0.89 5
e' 54.8800 Relative Permittivity (єr): 54.88 55.74 -1.54 5
9/18/2015 Body 700
e" 23.7800 Conductivity (σ): 0.93 0.96 -3.51 5
e' 53.8900 Relative Permittivity (єr): 53.89 55.39 -2.71 5
Body 790
e" 22.9700 Conductivity (σ): 1.01 0.97 4.43 5
e' 54.9000 Relative Permittivity (єr): 54.90 55.55 -1.16 5
Body 750
e" 23.2900 Conductivity (σ): 0.97 0.96 0.85 5
e' 55.4600 Relative Permittivity (єr): 55.46 55.74 -0.50 5
9/21/2015 Body 700
e" 23.7300 Conductivity (σ): 0.92 0.96 -3.71 5
e' 54.5000 Relative Permittivity (єr): 54.50 55.39 -1.61 5
Body 790
e" 22.9200 Conductivity (σ): 1.01 0.97 4.21 5
e' 41.0600 Relative Permittivity (єr): 41.06 41.96 -2.15 5
Head 750
e" 21.8300 Conductivity (σ): 0.91 0.89 1.94 5
e' 41.7300 Relative Permittivity (єr): 41.73 42.22 -1.16 5
9/21/2015 Head 700
e" 21.8400 Conductivity (σ): 0.85 0.89 -4.40 5
e' 40.5300 Relative Permittivity (єr): 40.53 41.76 -2.94 5
Head 790
e" 21.2000 Conductivity (σ): 0.93 0.90 3.92 5

Page 16 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015
System Check Results
The 1-g and 10-g SAR measured with a reference dipole, using the required tissue-equivalent medium at the test
frequency, must be within 10% of the manufacturer calibrated dipole SAR target.

SAR Lab A
System Dipole Measured Results
T.S. Target Delta Plot
Date Tested Zoom Scan to Normalize
Type Serial # Liquid (Ref. Value) ±10 % No.
100 mW to 1 W
1g 5.08 50.8 50.3 0.99
9/18/2015 D2450V2 748 Body 1,2
10g 2.32 23.2 23.5 -1.28
1g 5.31 53.1 52.7 0.76
9/18/2015 D2450V2 748 Head
10g 2.42 24.2 24.6 -1.63

SAR Lab B
System Dipole Measured Results
T.S. Target Delta Plot
Date Tested Zoom Scan to Normalize
Type Serial # Liquid (Ref. Value) ±10 % No.
100 mW to 1 W
1g 0.815 8.15 8.41 -3.09
9/18/2015 750 1024 Body
10g 0.541 5.41 5.60 -3.39
1g 0.852 8.52 8.41 1.31
9/21/2015 750 1024 Body
10g 0.566 5.66 5.60 1.07
1g 0.780 7.80 8.10 -3.70
9/21/2015 750 1024 Head 3,4
10g 0.513 5.13 5.33 -3.75

Page 18 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015
LTE Band 13 Measured Results
BW RB RB Target Avg Pwr (dBm)
Band Mode
(MHz) Allocation offset MPR 782 MHz
1 0 0 23.3
1 25 0 23.4
1 49 0 23.4
QPSK 25 0 1 22.5
25 12 1 22.6
25 25 1 22.6
LTE 50 0 1 22.6
10
Band 13 1 0 1 22.3
1 25 1 22.3
1 49 1 22.4
16QAM 25 0 2 21.5
25 12 2 21.6
25 25 2 21.6
50 0 2 21.6
BW RB RB Target Avg Pwr (dBm)
Band Mode
(MHz) Allocation offset MPR 782 MHz
1 0 0 23.4
1 12 0 23.4
1 24 0 23.5
QPSK 12 0 1 22.5
12 6 1 22.6
12 11 1 22.6
LTE 25 0 1 22.6
5
Band 13 1 0 1 22.2
1 12 1 22.2
1 24 1 22.3
16QAM 12 0 2 21.5
12 6 2 21.6
12 11 2 21.6
25 0 2 21.7

Note(s):
10/5 MHz Bandwidths does not support at least three non-overlapping channels in certain channel bandwidths. When a device
supports overlapping channel assignment in a channel bandwidth configuration, the middle channel of the group of overlapping
channels should be selected for testing per KDB 941225 D05 SAR for LTE Devices

Page 20 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

9.2. Wi-Fi 2.4GHz (DTS Band)
Measured Results
Band Freq. Avg Pwr (dBm) Max Output SAR Test
Mode Data Rate Ch #
(GHz) (MHz) Power (dBm) (Yes/No)
1 2412 16.3
802.11b 1 Mbps 6 2437 16.9 17.5 Yes
11 2462 16.1
1 2412
2.4 802.11g 6 Mbps 6 2437 13.5 No
11 2462
Not Required
1 2412
802.11n
6.5 Mbps 6 2437 12.5 No
(HT20)
11 2462

Note(s):
1. Output Power and SAR is not required for 802.11g/n HT20 channels when the highest reported SAR for DSSS is adjusted
by the ratio of OFDM to DSSS specified maximum output power and the adjusted SAR is ≤ 1.2 W/kg.

9.3. Bluetooth
Maximum tune-up tolerance limit is 10.5 dBm from the rated nominal maximum output power. This power level
qualifies for exclusion of SAR testing.

Page 21 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

10. Measured and Reported (Scaled) SAR Results
SAR Test Reduction criteria are as follows:

KDB 447498 D01 General RF Exposure Guidance:
Testing of other required channels within the operating mode of a frequency band is not required when the reported 1-g or 10-g
SAR for the mid-band or highest output power channel is:
 ≤ 0.8 W/kg or 2.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≤ 100 MHz
 ≤ 0.6 W/kg or 1.5 W/kg, for 1-g or 10-g respectively, when the transmission band is between 100 MHz and 200 MHz
 ≤ 0.4 W/kg or 1.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≥ 200 MHz

KDB 941225 D05 SAR for LTE Devices:
SAR test reduction is applied using the following criteria:
 Start with the largest channel bandwidth and measure SAR for QPSK with 1 RB, and 50% RB allocation, using the RB
offset and required test channel combination with the highest maximum output power among RB offsets at the upper edge,
middle and lower edge of each required test channel.
 When the reported SAR is > 0.8/2 W/kg, 1-g and 10-g respectively, testing for other Channels is performed at the highest
output power level for 1RB, and 50% RB configuration for that channel.
 Testing for 100% RB configuration is performed at the highest output power level for 100% RB configuration across the
Low, Mid and High Channel when the highest reported SAR for 1 RB and 50% RB are > 0.8/2 W/kg, 1-g and 10-g
respectively. Testing for the remaining required channels is not needed because the reported SAR for 100% RB Allocation
< 1.45/3.625 W/kg, 1-g and 10-g respectively.
 Testing for 16-QAM modulation is not required because the reported SAR for QPSK is < 1.45/3.625 W/Kg, 1-g and 10-g
respectively, and its output power is not more than 0.5 dB higher than that of QPSK.
 Testing for the other channel bandwidths is not required because the reported SAR for the highest channel bandwidth is <
1.45/3.625 W/Kg, 1-g and 10-g respectively, and its output power is not more than 0.5 dB higher than that of the highest
channel bandwidth.
 For LTE bands that do not support at least three non-overlapping channels in certain channel bandwidths, test the available
non-overlapping channels instead. When a device supports overlapping channel assignment in a channel bandwidth
configuration, the middle channel of the group of overlapping channels should be selected for testing; therefore, the
requirement for H, M and L channels may not fully apply.

Page 22 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015
KDB 248227 D01 SAR meas for 802.11:
SAR test reduction for 802.11 Wi-Fi transmission mode configurations are considered separately for DSSS and OFDM. An initial
test position is determined to reduce the number of tests required for certain exposure configurations with multiple test positions.
An initial test configuration is determined for each frequency band and aggregated band according to maximum output power,
channel bandwidth, wireless mode configurations and other operating parameters to streamline the measurement requirements.
For 2.4 GHz DSSS, either the initial test position or DSSS procedure is applied to reduce the number of SAR tests; these are
mutually exclusive. For OFDM, an initial test position is only applicable to next to the ear, UMPC mini-tablet and hotspot mode
configurations, which is tested using the initial test configuration to facilitate test reduction. For other exposure conditions with a
fixed test position, SAR test reduction is determined using only the initial test configuration.
The multiple test positions require SAR measurements in head, hotspot mode or UMPC mini-tablet configurations may be
reduced according to the highest reported SAR determined using the initial test position(s) by applying the DSSS or OFDM SAR
measurement procedures in the required wireless mode test configuration(s). The initial test position(s) is measured using the
highest measured maximum output power channel in the required wireless mode test configuration(s). When the reported SAR
for the initial test position is:

 ≤ 0.4/1 W/kg, 1-g and 10-g respectively, further SAR measurement is not required for the other test positions in that
exposure configuration and wireless mode combination within the frequency band or aggregated band. DSSS and
OFDM configurations are considered separately according to the required SAR procedures.
 > 0.4/1 W/kg, 1-g and 10-g respectively, SAR is repeated using the same wireless mode test configuration tested in the
initial test position to measure the subsequent next closet/smallest test separation distance and maximum coupling test
position, on the highest maximum output power channel, until the reported SAR is ≤ 0.8/2 W/kg, 1-g and 10-g
respectively, or all required test positions are tested.
o For subsequent test positions with equivalent test separation distance or when exposure is dominated by coupling
conditions, the position for maximum coupling condition should be tested.
o When it is unclear, all equivalent conditions must be tested.
 For all positions/configurations tested using the initial test position and subsequent test positions, when the reported
SAR is > 0.8/2 W/kg, 1-g and 10-g respectively, measure the SAR for these positions/configurations on the subsequent
next highest measured output power channel(s) until the reported SAR is ≤ 1.2/3 W/kg, 1-g and 10-g respectively, or all
required test channels are considered.
o The additional power measurements required for this step should be limited to those necessary for identifying
subsequent highest output power channels to apply the test reduction.
 When the specified maximum output power is the same for both UNII 1 and UNII 2A, begin SAR measurements in UNII
2A with the channel with the highest measured output power. If the reported SAR for UNII 2A is ≤ 1.2/3 W/kg, 1-g and
10-g respectively, SAR is not required for UNII 1; otherwise treat the remaining bands separately and test them
independently for SAR.
 When the specified maximum output power is different between UNII 1 and UNII 2A, begin SAR with the band that has
the higher specified maximum output. If the highest reported SAR for the band with the highest specified power is ≤
1.2/3 W/kg, 1-g and 10-g respectively, testing for the band with the lower specified output power is not required;
otherwise test the remaining bands independently for SAR.

To determine the initial test position, Area Scans were performed to determine the position with the Maximum Value of SAR
(measured). The position that produced the highest Maximum Value of SAR is considered the worst case position; thus used as
the initial test position.

Page 23 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

10.3. Standalone SAR Test Exclusion Considerations & Estimated SAR
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances
≤ 50 mm are determined by:
[(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)] ≤ 3.0, for 1-g SAR
and ≤ 7.5 for 10-g extremity SAR, where
 f(GHz) is the RF channel transmit frequency in GHz
 Power and distance are rounded to the nearest mW and mm before calculation
 The result is rounded to one decimal place for comparison
The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for
transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a
distance of 5 mm is applied to determine SAR test exclusion.

When the standalone SAR test exclusion is applied to an antenna that transmits simultaneously with other
antennas, the standalone SAR must be estimated according to following to determine simultaneous transmission
SAR test exclusion:
 (max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg for test
separation distances ≤ 50 mm;
where x = 7.5 for 1-g SAR, and x = 18.75 for 10-g SAR.
 0.4 W/kg for 1-g SAR and 1.0 W/kg for 10-g SAR, when the test separation distances is > 50 mm.

Extremity
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Configuration 10-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
10.5 11 5 2.480 3.5 Neck 0.185

Conclusion:
*: The computed value is ≤ 7.5; therefore, Bluetooth qualifies for Standalone SAR test exclusion.

Next-to-Mouth
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Configuration 1-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
10.5 11 10 2.480 1.7 Flat 0.231

Conclusion:
*: The computed value is ≤ 3; therefore, Bluetooth qualifies for Standalone SAR test exclusion.

Page 25 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

11. SAR Measurement Variability
In accordance with published RF Exposure KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. These
additional measurements are repeated after the completion of all measurements requiring the same head or body
tissue-equivalent medium in a frequency band. The test device should be returned to ambient conditions (normal
room temperature) with the battery fully charged before it is re-mounted on the device holder for the repeated
measurement(s) to minimize any unexpected variations in the repeated results.

1) Repeated measurement is not required when the original highest measured SAR is <1.6 or 2 W/kg (1-g or 10-g
respectively); steps 2) through 4) do not apply.
2) When the original highest measured SAR is ≥ 0.8 or 2 W/kg (1-g or 10-g respectively), repeat that
measurement once.
3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the original and first
repeated measurements is > 1.20 or 3 (1-g or 10-g respectively) or when the original or repeated measurement
is ≥ 1.45 or 3.6 W/kg (~ 10% from the 1-g or 10-g respective SAR limit).
4) Perform a third repeated measurement only if the original, first, or second repeated measurement is ≥ 1.5 or
3.75 W/kg (1-g or 10-g respectively) and the ratio of largest to smallest SAR for the original, first and second
repeated measurements is > 1.20 or 3 (1-g or 10-g respectively).

Extremity
Frequency Repeated Highest Repeated Largest to
Band Air Interface RF Exposure Conditions Test Position SAR Measured SAR Measured SAR Smallest
(MHz) (Yes/No) (W/kg) (W/kg) SAR Ratio
Extremity
750 LTE Band 13 Neck No 1.32 N/A N/A
(Hand/Wrist/Ankle)
Extremity
2400 Wi-Fi 802.11b/g/n Neck No 0.406 N/A N/A
(Hand/Wrist/Ankle)

Note(s):
Second Repeated Measurement is not required since the ratio of the largest to smallest SAR for the original and first repeated
measurement is not > 3 W/kg.

Next-to-Mouth
Frequency Repeated Highest Repeated Largest to
Band Air Interface RF Exposure Conditions Test Position SAR Measured SAR Measured SAR Smallest
(MHz) (Yes/No) (W/kg) (W/kg) SAR Ratio
750 LTE Band 13 Next to Mouth Flat No 0.255 N/A N/A
2400 Wi-Fi 802.11b/g/n Next to Mouth Flat No 0.091 N/A N/A

Note(s):
Second Repeated Measurement is not required since the ratio of the largest to smallest SAR for the original and first repeated
measurement is not > 1.20 W/kg.

Page 26 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I21799-S1V2 Issue Date: 9/30/2015

12. Simultaneous Transmission SAR Analysis
Simultaneous Transmission Condition
RF Exposure Condition Item Capable Transmit Configurations
1 LTE + DTS
Extremity & Next-to-Mouth
2 LTE + BT
Notes:
1. VoIP is supported in LTE.

12.1. Sum of the SAR for WWAN & Wi-Fi & BT (Extremity)
① +② ① +③
RF Expo sure ① ② ③ WWA N + DTS WWA N + B T
co nditio ns WWA N DTS BT ∑ 10-g SA R SP LSR ∑ 10-g SA R SP LSR
(mW/g) (Yes/ No ) (mW/g) (Yes/ No )

Extremity 1.414 0.497 0.185 1.9 11 No 1.599 No

12.2. Sum of the SAR for WWAN & Wi-Fi & BT (Next-to-Mouth)
① +② ① +③
RF Expo sure ① ② ③ WWA N + DTS WWA N + B T
co nditio ns WWA N DTS BT ∑ 1-g SA R SP LSR ∑ 1-g SA R SP LSR
(mW/g) (Yes/ No ) (mW/g) (Yes/ No )
Next-to -
0.273 0.104 0.231 0 .3 7 7 No 0.504 No
M o uth

Conclusion:
Simultaneous transmission SAR measurement (Volume Scan) is not required because the either sum of the 1-g SAR is <
1.6/4.0 W/kg, 1-g and 10-g respectively, or the SPLSR is ≤ 0.04 for 1-g and ≤ 0.10 for 10-g for all circumstances that require
SPLSR calculation.

Page 27 of 28
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Document Created: 2015-09-30 11:56:28
Document Modified: 2015-09-30 11:56:28

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC