SAR Report revA

FCC ID: ZNFW150

RF Exposure Info

Download: PDF
FCCID_2573023

SAR EVALUATION REPORT FCC 47 CFR § 2.1093 IEEE Std 1528-2013 For SMART WATCH WITH 2.4 DTS b/g/n + BT & BLE FCC ID: ZNFW150 Model Name: LG-W150, LGW150, W150 Report Number: 15I20081-S1A Issue Date: 4/1/2015 Prepared for LG ELECTRONICS MOBILECOMM U.S.A., INC. 1000 SYLVAN AVE. ENGLEWOOD CLIFFS, NJ 07632 Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 NVLAP LAB CODE 200065-0

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Revision History Rev. Date Revisions Revised By -- 2/25/2015 Initial Issue -- 4/1/2015 Updated Extremity SAR to include high and low channels. Yu Chen Page 2 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Table of Contents 1. Test Specification, Methods and Procedures............................................................................ 5 2. Facilities and Accreditation ........................................................................................................ 5 3. SAR Measurement System & Test Equipment .......................................................................... 6 3.1. SAR Measurement System ........................................................................................................ 6 3.2. SAR Scan Procedures ............................................................................................................... 7 3.3. Test Equipment.......................................................................................................................... 9 4. Measurement Uncertainty ......................................................................................................... 10 5. Device Under Test (DUT) Information ...................................................................................... 11 5.1. DUT Description ...................................................................................................................... 11 5.2. Wireless Technologies ............................................................................................................. 11 5.3. Nominal and Maximum Output Power...................................................................................... 11 6. RF Exposure Conditions (Test Configurations) ...................................................................... 12 7. Dielectric Property Measurements & System Check .............................................................. 13 7.1. Dielectric Property Measurements ........................................................................................... 13 7.2. System Check.......................................................................................................................... 15 8. Conducted Output Power Measurements................................................................................ 17 8.1. Wi-Fi 2.4GHz (DTS Band) ....................................................................................................... 17 8.2. Bluetooth ................................................................................................................................. 17 9. Measured and Reported (Scaled) SAR Results ....................................................................... 18 9.1. Wi-Fi (DTS Band) .................................................................................................................... 19 9.2. Bluetooth ................................................................................................................................. 19 10. SAR Measurement Variability ................................................................................................... 20 11. Simultaneous Transmission SAR Analysis ............................................................................. 21 Appendixes .......................................................................................................................................... 22 A_15I20081v0 SAR Photos & Ant. Locations ..................................................................................... 22 B_15I20081v0 SAR System Check Plots ........................................................................................... 22 C_15I20081v1 SAR Highest Test Plots .............................................................................................. 22 D_15I20081v0 SAR Tissue Ingredients .............................................................................................. 22 E_15I20081v0 SAR Probe Cal. Certificates ........................................................................................ 22 F_15I20081v0 SAR Dipole Cal. Certificates ....................................................................................... 22 Page 3 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Attestation of Test Results Applicant Name LG ELECTRONICS MOBILECOMM U.S.A., INC. FCC ID ZNFW150 Model Name LG-W150, LGW150, W150 Applicable Standards FCC 47 CFR § 2.1093 Published RF exposure KDB procedures IEEE Std 1528-2013 SAR Limits (W/Kg) Peak spatial-average(1g of tissue) Extremities (hands, wrists, ankles, etc.) Exposure Category (10g of tissue) General population / 1.6 4 Uncontrolled exposure The Highest Reported SAR (W/kg) Equipment Class RF Exposure Conditions Licensed DTS U-NII DSS (BT) Next to Mouth N/A 0.150 N/A N/A Extremity N/A 0.511 N/A N/A Date Tested 2/16/2015 to 2/19/2015 Test Results Pass UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government (NIST Handbook 150, Annex A). This report is written to support regulatory compliance of the applicable standards stated above. Approved & Released By: Prepared By: Bobby Bayani Yu Chen Senior Engineer Laboratory Technician UL Verification Services Inc. UL Verification Services Inc. Page 4 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 1. Test Specification, Methods and Procedures The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE STD 1528- 2013, the following FCC Published RF exposure KDB procedures: o 248227 D01 SAR meas for 802.11 v02 o 447498 D01 General RF Exposure Guidance v05r02 o 447498 D03 Supplement C Cross-Reference o 690783 D01 SAR Listings on Grants v01r03 o 865664 D01 SAR measurement 100 MHz to 6 GHz v01r03 o 865664 D02 RF Exposure Reporting v01r01 2. Facilities and Accreditation The test sites and measurement facilities used to collect data are located at 47173 Benicia Street 47266 Benicia Street SAR Lab A SAR Lab 1 SAR Lab B SAR Lab 2 SAR Lab C SAR Lab 3 SAR Lab D SAR Lab 4 SAR Lab E SAR Lab 5 SAR Lab F SAR Lab G SAR Lab H UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0. Page 5 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 3. SAR Measurement System & Test Equipment 3.1. SAR Measurement System The DASY5 system used for performing compliance tests consists of the following items:  A standard high precision 6-axis robot with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE).  An isotropic Field probe optimized and calibrated for the targeted measurement.  A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD- conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC.  The Electro-optical converter (EOC) performs the conversion from optical to electrical signals for the digital communication to the DAE. To use optical surface detection, a special version of the EOC is required. The EOC signal is transmitted to the measurement server.  The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts.  The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe positioning.  A computer running WinXP or Win7 and the DASY5 software.  Remote control and teach pendant as well as additional circuitry for robot safety such as warning lamps, etc.  The phantom, the device holder and other accessories according to the targeted measurement. Page 6 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 3.2. SAR Scan Procedures Step 1: Power Reference Measurement The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 2.1 mm. This distance cannot be smaller than the distance of sensor calibration points to probe tip as defined in the probe properties. Step 2: Area Scan The Area Scan is used as a fast scan in two dimensions to find the area of high field values, before doing a fine measurement around the hot spot. The sophisticated interpolation routines implemented in DASY software can find the maximum locations even in relatively coarse grids. When an Area Scan has measured all reachable points, it computes the field maximal found in the scanned area, within a range of the global maximum. The range (in dB) is specified in the standards for compliance testing. For example, a 2 dB range is required in IEEE Standard 1528 and IEC 62209 standards, whereby 3 dB is a requirement when compliance is assessed in accordance with the ARIB standard (Japan). If only one Zoom Scan follows the Area Scan, then only the absolute maximum will be taken as reference. For cases where multiple maximums are detected, the number of Zoom Scans has to be increased accordingly. Area Scan Parameters extracted from KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Page 7 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Step 3: Zoom Scan Zoom Scans are used to assess the peak spatial SAR values within a cubic averaging volume containing 1 g and 10 g of simulated tissue. The Zoom Scan measures points (refer to table below) within a cube whose base faces are centered on the maxima found in a preceding area scan job within the same procedure. When the measurement is done, the Zoom Scan evaluates the averaged SAR for 1 g and 10 g and displays these values next to the job’s label. Zoom Scan Parameters extracted from KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Step 4: Power drift measurement The Power Drift Measurement measures the field at the same location as the most recent power reference measurement within the same procedure, and with the same settings. The Power Drift Measurement gives the field difference in dB from the reading conducted within the last Power Reference Measurement. This allows a user to monitor the power drift of the device under test within a batch process. The measurement procedure is the same as Step 1. Step 5: Z-Scan (FCC only) The Z Scan measures points along a vertical straight line. The line runs along the Z-axis of a one-dimensional grid. In order to get a reasonable extrapolation the extrapolated distance should not be larger than the step size in Z- direction. Page 8 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 3.3. Test Equipment The measuring equipment used to perform the tests documented in this report has been calibrated in accordance with the manufacturers’ recommendations, and is traceable to recognized national standards. Dielectric Property Measurements Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Network Analyzer Agilent 8753ES MY40001647 7/17/2015 Dielectronic Probe kit SPEAG DAK-3.5 1087 11/11/2015 Dielectronic Probe kit SPEAG DAK-3.5 Short SM DAK 200 BA N/A Traceable Calibration Thermometer Control Co. 4242 122529162 10/8/2015 System Check Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Synthesized Signal Generator HP 8665B 3744A01084 5/20/2015 Power Meter Agilent N1912A MY53040016 5/5/2015 Power Sensor Agilent E9323A MY53070005 5/1/2015 Power Sensor Agilent E9323A MY53070009 5/28/2015 Amplifier MITEQ AMF-4D-00400600-50-30P 1795093 N/A Directional coupler Werlatone C8060-102 2149 N/A DC Power Supply AMETEK XT 15-4 1319A02778 N/A Synthesized Signal Generator HP 8665B 3744A01155 3/12/2015 Power Meter HP 437B 3125U11364 8/27/2015 Power Meter HP 437B 3125U12345 8/15/2015 Power Sensor HP 8481A 1926A27048 8/15/2015 Power Sensor HP 8481A 2702A76223 9/17/2015 Amplifier MITEQ AMF-4D-00400600-50-30P 1795092 N/A Directional coupler Werlatone C8060-102 2141 N/A DC Power Supply BK PRECISION 1611 215-02292 N/A E-Field Probe (SAR Lab G) SPEAG EX3DV4 3990 4/15/2015 Data Acquisition Electronics (SAR Lab G) SPEAG DAE4 1434 4/14/2015 System Validation Dipole SPEAG D2450V2 706 5/20/2015 Other Name of Equipment Manufacturer Type/Model Serial No. Cal. Due Date Power Meter Agilent N1921A MY52200012 9/26/2015 Power Sensor Agilent N1911A MY53060009 5/5/2015 Page 9 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 4. Measurement Uncertainty Per KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz, when the highest measured 1-g SAR within a frequency band is < 1.5 W/kg, the extensive SAR measurement uncertainty analysis described in IEEE Std 1528- 2013 is not required in SAR reports submitted for equipment approval. Page 10 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 5. Device Under Test (DUT) Information 5.1. DUT Description Device Dimension Overall (Length x Width): 56.5 mm x 45.4 mm (excluding strap) Overall Diagonal: 62.0 mm Display Diagonal: 35.0 mm Back Cover ☒ The rechargeable battery is not user accessible. Battery Options ☒ The rechargeable battery is not user accessible. Wi-Fi Direct Wi-Fi Direct enabled devices transfer data directly between each other ☒ Wi-Fi Direct (Wi-Fi 2.4 GHz) 5.2. Wireless Technologies Wireless Frequency bands Operating mode Duty Cycle used for SAR technologies testing Wi-Fi 2.4 GHz 802.11b 100% 802.11g 802.11n (HT20) Bluetooth 2.4 GHz Version 1.2 N/A Version 2.0 + EDR Version 2.1 + EDR Version 3.0 + HS Version 4.0 LE 5.3. Nominal and Maximum Output Power KDB 447498 sec.4.1.(3) at the maximum rated output power and within the tune-up tolerance range specified for the product, but not more than 2 dB lower than the maximum tune-up tolerance limit Upper limit (dB): ~ 1.0 Max. RF Output Pow er (dBm) Max. tune-up RF Air interface Mode Target tolerance limit 802.11b 17.0 18.0 WiFi 2.4 GHz 802.11g 14.0 15.0 802.11n HT20 13.0 14.0 Upper limit (dB): ~ 1.5 Max. RF Output Pow er (dBm) Max. tune-up RF Air interface Mode Target tolerance limit Bluetooth (GFSK) 8.5 10.0 Bluetooth (DPSK) 5.5 7.0 Bluetooth (8DPSK) 5.5 7.0 Bluetooth (LE) 7.5 9.0 Page 11 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 6. RF Exposure Conditions (Test Configurations) Refer to “SAR Photos and Ant locations” Appendix for the specific details of the antenna-to-antenna and antenna-to-edge(s) distances. Wireless RF Exposure DUT-to-User Test Antenna-to- SAR Note technologies Conditions Separation Position edge/surface Required Extremity 0mm Rear N/A Yes WLAN (Hand/Wrist/Ankle) Next to Mouth 10mm Front N/A Yes Page 12 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 7. Dielectric Property Measurements & System Check 7.1. Dielectric Property Measurements The temperature of the tissue-equivalent medium used during measurement must also be within 18C to 25C and within ± 2C of the temperature when the tissue parameters are characterized. The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR measurements. The parameters should be re-measured after each 3 – 4 days of use; or earlier if the dielectric parameters can become out of tolerance; for example, when the parameters are marginal at the beginning of the measurement series. Tissue dielectric parameters were measured at the low, middle and high frequency of each operating frequency range of the test device. Tissue Dielectric Parameters FCC KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz Head Body Target Frequency (MHz) er s (S/m) er s (S/m) 150 52.3 0.76 61.9 0.80 300 45.3 0.87 58.2 0.92 450 43.5 0.87 56.7 0.94 835 41.5 0.90 55.2 0.97 900 41.5 0.97 55.0 1.05 915 41.5 0.98 55.0 1.06 1450 40.5 1.20 54.0 1.30 1610 40.3 1.29 53.8 1.40 1800 – 2000 40.0 1.40 53.3 1.52 2450 39.2 1.80 52.7 1.95 3000 38.5 2.40 52.0 2.73 5000 36.2 4.45 49.3 5.07 5100 36.1 4.55 49.1 5.18 5200 36.0 4.66 49.0 5.30 5300 35.9 4.76 48.9 5.42 5400 35.8 4.86 48.7 5.53 5500 35.6 4.96 48.6 5.65 5600 35.5 5.07 48.5 5.77 5700 35.4 5.17 48.3 5.88 5800 35.3 5.27 48.2 6.00 IEEE Std 1528-2013 Refer to Table 3 within the IEEE Std 1528-2013 Page 13 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Dielectric Property Measurements Results: SAR Lab G Date Freq. (MHz) Liquid Parameters Measured Target Delta (%) Limit ±(%) e' 40.5100 Relative Permittivity (єr): 40.51 39.20 3.34 5 Head 2450 e" 13.7500 Conductivity (σ): 1.87 1.80 4.06 5 e' 40.6600 Relative Permittivity (єr): 40.66 39.28 3.52 5 2/16/2015 Head 2410 e" 13.6200 Conductivity (σ): 1.83 1.76 3.67 5 e' 40.4100 Relative Permittivity (єr): 40.41 39.17 3.17 5 Head 2475 e" 13.7700 Conductivity (σ): 1.89 1.83 3.72 5 e' 51.6700 Relative Permittivity (єr): 51.67 52.70 -1.95 5 Body 2450 e" 14.8300 Conductivity (σ): 2.02 1.95 3.60 5 e' 51.8100 Relative Permittivity (єr): 51.81 52.76 -1.80 5 2/16/2015 Body 2410 e" 14.6800 Conductivity (σ): 1.97 1.91 3.13 5 e' 51.5500 Relative Permittivity (єr): 51.55 52.67 -2.12 5 Body 2475 e" 14.9100 Conductivity (σ): 2.05 1.99 3.36 5 Page 14 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 7.2. System Check SAR system verification is required to confirm measurement accuracy, according to the tissue dielectric media, probe calibration points and other system operating parameters required for measuring the SAR of a test device. The system verification must be performed for each frequency band and within the valid range of each probe calibration point required for testing the device. The same SAR probe(s) and tissue-equivalent media combinations used with each specific SAR system for system verification must be used for device testing. When multiple probe calibration points are required to cover substantially large transmission bands, independent system verifications are required for each probe calibration point. A system verification must be performed before each series of SAR measurements using the same probe calibration point and tissue-equivalent medium. Additional system verification should be considered according to the conditions of the tissue-equivalent medium and measured tissue dielectric parameters, typically every three to four days when the liquid parameters are re-measured or sooner when marginal liquid parameters are used at the beginning of a series of measurements. System Performance Check Measurement Conditions:  The measurements were performed in the flat section of the TWIN SAM or ELI phantom, shell thickness: 2.0 ±0.2 mm (bottom plate) filled with Body or Head simulating liquid of the following parameters.  The depth of tissue-equivalent liquid in a phantom must be ≥ 15.0 cm for SAR measurements ≤ 3 GHz and ≥ 10.0 cm for measurements > 3 GHz.  The DASY system with an E-Field Probe was used for the measurements.  The dipole was mounted on the small tripod so that the dipole feed point was positioned below the center marking of the flat phantom section and the dipole was oriented parallel to the body axis (the long side of the phantom). The standard measuring distance was 10 mm (above 1 GHz) and 15 mm (below 1 GHz) from dipole center to the simulating liquid surface.  The coarse grid with a grid spacing of 15 mm was aligned with the dipole. For 5 GHz band - The coarse grid with a grid spacing of 10 mm was aligned with the dipole.  Special 7x7x7 (below 3 GHz) and/or 8x8x7 (above 3 GHz) fine cube was chosen for the cube.  Distance between probe sensors and phantom surface was set to 3 mm. For 5 GHz band - Distance between probe sensors and phantom surface was set to 2.5 mm  The dipole input power (forward power) was 100 mW.  The results are normalized to 1 W input power. Page 15 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Reference Target SAR Values The reference SAR values can be obtained from the calibration certificate of system validation dipoles Target SAR Values (W/kg) System Dipole Serial No. Cal. Date Freq. (MHz) 1g/10g Head Body 1g 53.0 50.2 D2450V2 706 5/20/2014 2450 10g 24.5 23.4 System Check Results The 1-g and 10-g SAR measured with a reference dipole, using the required tissue-equivalent medium at the test frequency, must be within 10% of the manufacturer calibrated dipole SAR target. SAR Lab G System Dipole Measured Results T.S. Target Delta Plot Date Tested Zoom Scan to Normalize Type Serial # Liquid (Ref. Value) ±10 % No. 100 mW to 1 W 1g 5.42 54.20 53.00 2.26 2/16/2015 D2450V2 706 Head 10g 2.47 24.70 24.50 0.82 1g 4.85 48.50 50.20 -3.39 2/16/2015 D2450V2 706 Body 1,2 10g 2.24 22.40 23.40 -4.27 Page 16 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 8. Conducted Output Power Measurements 8.1. Wi-Fi 2.4GHz (DTS Band) Measured Results Band Freq. Avg Pwr (dBm) Max Output SAR Test Mode Data Rate Ch # Note(s) (GHz) (MHz) Power (dBm) (Yes/No) 1 2412 17.0 802.11b 1 Mbps 6 2437 17.0 18.0 Yes 11 2462 17.0 1 2412 2.4 802.11g 6 Mbps 6 2437 15.0 No 1 11 2462 Not Required 1 2412 802.11n MCS0 6 2437 14.0 No 1 (HT20) 11 2462 Note(s): 1. Output Power and SAR is not required for 802.11g/n HT20 channels when the highest reported SAR for DSSS is adjusted by the ratio of OFDM to DSSS specified maximum output power and the adjusted SAR is ≤ 1.2 W/kg. 8.2. Bluetooth Maximum tune-up tolerance limit is 10.0 dBm from the rated nominal maximum output power. This power level qualifies for exclusion of SAR testing. Page 17 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 9. Measured and Reported (Scaled) SAR Results SAR Test Reduction criteria are as follows: KDB 248227 D01 SAR meas for 802.11 v02: SAR test reduction for 802.11 Wi-Fi transmission mode configurations are considered separately for DSSS and OFDM. An initial test position is determined to reduce the number of tests required for certain exposure configurations with multiple test positions. An initial test configuration is determined for each frequency band and aggregated band according to maximum output power, channel bandwidth, wireless mode configurations and other operating parameters to streamline the measurement requirements. For 2.4 GHz DSSS, either the initial test position or DSSS procedure is applied to reduce the number of SAR tests; these are mutually exclusive. For OFDM, an initial test position is only applicable to next to the ear, UMPC mini-tablet and hotspot mode configurations, which is tested using the initial test configuration to facilitate test reduction. For other exposure conditions with a fixed test position, SAR test reduction is determined using only the initial test configuration. The multiple test positions require SAR measurements in head, hotspot mode or UMPC mini-tablet configurations may be reduced according to the highest reported SAR determined using the initial test position(s) by applying the DSSS or OFDM SAR measurement procedures in the required wireless mode test configuration(s). The initial test position(s) is measured using the highest measured maximum output power channel in the required wireless mode test configuration(s). When the reported SAR for the initial test position is:  ≤ 0.4 W/kg, further SAR measurement is not required for the other test positions in that exposure configuration and wireless mode combination within the frequency band or aggregated band. DSSS and OFDM configurations are considered separately according to the required SAR procedures.  > 0.4 W/kg, SAR is repeated using the same wireless mode test configuration tested in the initial test position to measure the subsequent next closet/smallest test separation distance and maximum coupling test position, on the highest maximum output power channel, until the reported SAR is ≤ 0.8 W/kg or all required test positions are tested. o For subsequent test positions with equivalent test separation distance or when exposure is dominated by coupling conditions, the position for maximum coupling condition should be tested. o When it is unclear, all equivalent conditions must be tested.  For all positions/configurations tested using the initial test position and subsequent test positions, when the reported SAR is > 0.8 W/kg, measure the SAR for these positions/configurations on the subsequent next highest measured output power channel(s) until the reported SAR is ≤ 1.2 W/kg or all required test channels are considered. o The additional power measurements required for this step should be limited to those necessary for identifying subsequent highest output power channels to apply the test reduction. Page 18 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 9.1. Wi-Fi (DTS Band) Power (dBm) 1-g SAR (W/kg) 10-g SAR (W/kg) Frequency RF Exposure Dist. Freq. Plot Mode Test Position Ch #. Tune-up Band Conditions (mm) (MHz) Meas. Meas. Scaled Meas. Scaled No. limit 1 2412.0 18.0 17.0 0.406 0.511 1 Extremity 0 Rear 6 2437.0 18.0 17.0 0.351 0.442 2.4GHz 802.11b 11 2462.0 18.0 17.0 0.388 0.488 Next to Mouth 10 Front 6 2437.0 18.0 17.0 0.119 0.150 2 9.2. Bluetooth Standalone SAR Test Exclusion Considerations & Estimated SAR The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)] ≤ 3.0, for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. When the standalone SAR test exclusion is applied to an antenna that transmits simultaneously with other antennas, the standalone SAR must be estimated according to following to determine simultaneous transmission SAR test exclusion:  (max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg for test separation distances ≤ 50 mm; where x = 7.5 for 1-g SAR, and x = 18.75 for 10-g SAR.  0.4 W/kg for 1-g SAR and 1.0 W/kg for 10-g SAR, when the test separation distances is > 50 mm. Extremity Exposure Conditions Max. tune-up tolerance limit Min. test Frequency SAR test Test separation (GHz) exclusion Configuration (dBm) (mW) distance (mm) Result* 10.0 10 5 2.480 3.1 Extremity Conclusion: *: The computed value is < 7.5; therefore, Bluetooth qualifies for Standalone SAR test exclusion. Next to Mouth Exposure Conditions Max. tune-up tolerance limit Min. test Frequency SAR test Test separation (GHz) exclusion Configuration (dBm) (mW) distance (mm) Result* 10.0 10 10 2.480 1.6 Next to Mouth Conclusion: *: The computed value is < 3; therefore, Bluetooth qualifies for Standalone SAR test exclusion. Page 19 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 10. SAR Measurement Variability In accordance with published RF Exposure KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. These additional measurements are repeated after the completion of all measurements requiring the same head or body tissue-equivalent medium in a frequency band. The test device should be returned to ambient conditions (normal room temperature) with the battery fully charged before it is re-mounted on the device holder for the repeated measurement(s) to minimize any unexpected variations in the repeated results. 1) Repeated measurement is not required when the original highest measured SAR is < 0.80 W/kg; steps 2) through 4) do not apply. 2) When the original highest measured SAR is ≥ 0.80 W/kg, repeat that measurement once. 3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the original and first repeated measurements is > 1.20 or when the original or repeated measurement is ≥ 1.45 W/kg (~ 10% from the 1-g SAR limit). 4) Perform a third repeated measurement only if the original, first or second repeated measurement is ≥1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. Frequency Repeated Highest Repeated Largest to Air Interface RF Exposure Conditions Test Position Band SAR Measured SAR Measured SAR Smallest Extremity Rear No 0.351 N/A N/A 2400 Wi-Fi 802.11b/g/n Next to Mouth Front No 0.119 N/A N/A Page 20 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 11. Simultaneous Transmission SAR Analysis N/A Wi-Fi 2.4GHz Radio cannot transmit simultaneously with Bluetooth Radio. Page 21 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 15I20081-S1A Issue Date: 4/1/2015 Appendixes Refer to separated files for the following appendixes. A_15I20081v0 SAR Photos & Ant. Locations B_15I20081v0 SAR System Check Plots C_15I20081v1 SAR Highest Test Plots D_15I20081v0 SAR Tissue Ingredients E_15I20081v0 SAR Probe Cal. Certificates F_15I20081v0 SAR Dipole Cal. Certificates END OF REPORT Page 22 of 22 UL Verification Services Inc. Doc. No.: 1.0 This report shall not be reproduced without the written approval of UL Verification Services Inc.


Document Created: 2015-04-01 09:20:08
Document Modified: 2015-04-01 09:20:08
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC