Part 15C BT LE Test Report

FCC ID: ZNFVS890

Test Report

Download: PDF
FCCID_2014200

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC PART 15.247 Bluetooth (Low Energy) Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 06/10 - 06/14/2013 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0Y1306100966.ZNF FCC ID: ZNFVS890 APPLICANT: LG Electronics MobileComm U.S.A Application Type: Class II Permissive Change Model: VS890, LG-VS890, LGVS890 EUT Type: Portable Handset Max. RF Output Power: 5.79 mW (7.63 dBm) Peak Conducted Frequency Range: 2402 - 2480 MHz FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15.247 Test Procedure(s): KDB 558074 v03r01 Class II Permissive Change: Please see FCC change documents. Original Grant Date: June 14, 2013 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 558074 v03r01. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

T A B L E O F C O N T E N T S FCC PART 15.247 MEASUREMENT REPORT .................................................................................................. 3 1.0 INTRODUCTION......................................................................................................................................4 1.1 SCOPE....................................................................................................................................................... 4 1.2 PCTEST TEST LOCATION........................................................................................................................ 4 2.0 PRODUCT INFORMATION .....................................................................................................................5 2.1 EQUIPMENT DESCRIPTION..................................................................................................................... 5 2.2 DEVICE CAPABILITIES............................................................................................................................. 5 2.3 TEST CONFIGURATION ........................................................................................................................... 5 2.4 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS.................................................................................. 5 2.5 LABELING REQUIREMENTS .................................................................................................................... 5 3.0 DESCRIPTION OF TEST ........................................................................................................................6 3.1 EVALUATION PROCEDURE..................................................................................................................... 6 3.2 RADIATED EMISSIONS ............................................................................................................................ 6 4.0 ANTENNA REQUIREMENTS..................................................................................................................7 5.0 TEST EQUIPMENT CALIBRATION DATA..............................................................................................8 6.0 TEST RESULTS ......................................................................................................................................9 6.1 SUMMARY ................................................................................................................................................. 9 6.2 RADIATED SPURIOUS EMISSION MEASUREMENTS.......................................................................... 10 6.3 RADIATED RESTRICTED BAND EDGE MEASUREMENTS .................................................................. 15 7.0 CONCLUSION .......................................................................................................................................16 FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

MEASUREMENT REPORT FCC Part 15.247 § 2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland MIlls Road, Columbia, MD 21046 USA FCC RULE PART(S): Part 15.247 IC SPECIFICATION(S): RSS-210 Issue 8 FCC ID: ZNFVS890 Test Device Serial No.: BT/WiFi #1 Production Pre-Production Engineering FCC CLASSIFICATION: Digital Transmission System (DTS) DATE(S) OF TEST: 06/10 - 06/14/2013 TEST REPORT S/N: 0Y1306100966.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451B-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 PCTEST Test Location The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity are, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39o 10’23” N latitude and 76o 49’50” W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on February 15, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFVS890. The data found in this test report was taken with the EUT operating in Bluetooth low energy mode. While in low energy mode, the Bluetooth transmitter hops pseudo-randomly between 40 channels, three of which are “advertising channels”. When the transmitter is hopping only between the three advertising channels, the EUT does not fall under the category of a “hopper” as defined in 15.247(a)(iii) which states that a “frequency hopping systems in the 2400– 2483.5 MHz band shall use at least 15 channels.” As operation on only the advertising channels does not qualify the EUT as a hopper, the EUT is certified as a DTS device in this mode. The data found in this report is representative of the device when it transmits on its advertising channels. Typical Bluetooth operation is covered under the DSS report found with this application. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A (BC0, BC1), Band 13 (10MHz BW) LTE, 802.11b/g/n WLAN, Bluetooth (1x,EDR, LE) 2.3 Test Configuration The LG Portable Handset FCC ID: ZNFVS890 was tested per the guidance of KDB 558074 v03r01. ANSI C63.10-2009 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. See Sections 3.2 of this test report for a description of the radiated emissions test setup. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. 2.5 Labeling Requirements Per 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name and FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

3.0 DESCRIPTION OF TEST 3.1 Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed Wireless Devices (ANSI C63.10-2009), and the guidance provided in KDB 558074 v03r01 were used in the measurement of the LG Portable Handset FCC ID: ZNFVS890. Deviation from measurement procedure…………………………………………….....................................None 3.2 Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi- anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An ETS Lindgren Model 2188 raised turntable is used for radiated measurement. It is a continuously rotatable, remote- controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. A 78cm high PVC support structure is placed on top of the turntable. A ¾” (~1.9cm) sheet of high density polyethylene is used as the table top and is placed on top of the PVC supports to bring the total height of the table to 80cm. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 0.8 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. For the EUT positioning, “H” is defined with the EUT lying flat on the test surface, “H2” is defined with the EUT standing up on its side, and “V” is defined with the EUT standing upright. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna(s) of the Portable Handset are permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The LG Portable Handset FCC ID: ZNFVS890 unit complies with the requirement of §15.203. Ch. Frequency (MHz) 0 2402 : : 19 2440 : : 39 2480 Table 4-1. Frequency / Channel Operations FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

5.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Table 5-1. Annual Test Equipment Calibration Schedule Note: For equipment listed above that has a calibration due date that falls within the test date range, care was taken to ensure that this equipment was utilized prior to the calibration due date. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

6.0 TEST RESULTS 6.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFVS890 FCC Classification: Digital Transmission System (DTS) Number of Channels: 40 FCC Part RSS Test Test Test Description Test Limit Reference Section(s) Section(s) Condition Result TRANSMITTER MODE (TX) Emissions in restricted bands General Field Strength Limits 15.205 must meet the radiated limits Sections 6.2, RSS-210 [A8.5] (Restricted Bands and RADIATED PASS 15.209 detailed in 15.209 (RSS-210 6.3 Radiated Emission Limits) table 3 limits) Table 6-1. Summary of Test Results Notes: 1. All modes of operation were investigated. The test results shown in the following sections represent the worst case emissions. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

6.2 Radiated Spurious Emission Measurements §15.205, §15.209, §15.247(d); RSS-210 [A8.5] Test Overview and Limit All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive antenna while the EUT is operating at maximum power and at the appropriate frequencies. Only the radiated emissions of the configuration that produced the worst case emissions are reported in this section. All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table 6-2 per Section 15.209. Field Strength Measured Distance Frequency [V/m] [Meters] 0.009 – 0.490 MHz 2400/F (kHz) 300 0.490 – 1.705 MHz 24000/F (kHz) 30 1.705 – 30.00 MHz 30 30 30.00 – 88.00 MHz 100 3 88.00 – 216.0 MHz 150 3 216.0 – 960.0 MHz 200 3 Above 960.0 MHz 500 3 Table 6-2. Radiated Limits Test Procedures Used KDB 558074 v03r01 – Section 12.2.5 (average power measurements) KDB 558074 v03r01 – Section 12.2.4 (peak power measurements) Test Settings Average Field Strength Measurements per Section 12.2.5.3 of KDB 558074 v03r01 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3kHz > 1/T 4. Averaging type was set to RMS to ensure that video filtering was applied in the power domain 5. Detector = peak 6. Sweep time = auto 7. Trace mode = max hold 8. Trace was allowed to run for at least 50 times (1/duty cycle) traces FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

Peak Field Strength Measurements per Section 12.2.4 of KDB 558074 v03r01 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW is set depending on measurement frequency, as specified in Table 6-3 below 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize Frequency RBW 9 – 150kHz 200 – 300Hz 0.15 – 30MHz 9 – 10kHz 30 – 1000MHz 100 – 120kHz > 1000MHz 1MHz Table 6-3. RBW as a Function of Frequency Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 6-1. Test Instrument & Measurement Setup Test Notes 1. The optional test procedures for antenna port conducted measurements of unwanted emissions per the guidance of KDB 558074 v03r01 were not used to evaluate this device for compliance to radiated limits. All radiated spurious emissions levels were measured in a radiated test setup. 2. All emissions lying in restricted bands specified in §15.205 are below the limit shown in Table 6-3. 3. The antenna is manipulated through typical positions, polarity and length during the tests. The EUT is manipulated through three orthogonal planes. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

4. The EUT is supplied with nominal AC voltage and/or a new/fully-recharged battery. 5. The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter using CISPR quasi peak detector below 1GHz. Above 1 GHz, average and peak measurements were taken using linearly polarized horn antennas. The worst-case emissions are reported however emissions whose levels were not within 20dB of the respective limits were not reported. 6. Average measurements were recorded using a VBW of 3kHz, per Section 12.2.4.3 of KDB 558074 v03r01, since 1/T is equal to just under 3kHz. This method was used because the EUT could not be configured to operate with a duty cycle > 98%. Both average and peak measurements were made using a peak detector 7. Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. 8. Average levels at -135dBm and peak levels at -125dBm represent the analyzer noise floor and signify that no emission was detected. 9. No significant radiated band edge emissions were found in the 2310 – 2390MHz restricted band. 10. Due to some of the in-band signal being captured at the band edge, measurements that fall within 1MHz of the high band edge were measured using the marker delta method per Section 13 of KDB 558074. Sample Calculations Determining Spurious Emissions Levels o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] o Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] Radiated Band Edge Measurement Offset o The amplitude offset shown in the radiated restricted band edge plots in Section 6.3 was calculated using the formula: Offset (dB) = (Antenna Factor + Cable Loss + 10 dB Attenuator) – Preamplifier Gain FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

Radiated Spurious Emission Measurements (Cont’d) §15.205, §15.209, §15.247(d); RSS-210 [A8.5] Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2402MHz Channel: 0 Analyzer Field Frequency Pol AFCL Limit Margin Level Detector Strength [MHz] [H/V] [dB] [dBV/m] [dB] [dBm] [dBV/m] 4804.00 -108.81 Avg H 41.22 39.41 53.98 -14.57 4804.00 -98.83 Peak H 41.22 49.39 73.98 -24.59 12010.00 -135.00 Avg H 52.26 24.26 53.98 -29.72 12010.00 -125.00 Peak H 52.26 34.26 73.98 -39.72 Table 6-4. Radiated Measurements @ 3 meters Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2440MHz Channel: 19 Analyzer Field Frequency Pol AFCL Limit Margin Level Detector Strength [MHz] [H/V] [dB] [dBV/m] [dB] [dBm] [dBV/m] 4880.00 -109.13 Avg H 41.20 39.06 53.98 -14.92 4880.00 -98.95 Peak H 41.20 49.24 73.98 -24.74 7320.00 -135.00 Avg H 44.85 16.85 53.98 -37.13 7320.00 -125.00 Peak H 44.85 26.85 73.98 -47.13 12200.00 -135.00 Avg H 52.54 24.54 53.98 -29.44 12200.00 -125.00 Peak H 52.54 34.54 73.98 -39.44 Table 6-5. Radiated Measurements @ 3 meters FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

Radiated Spurious Emission Measurements (Cont’d) §15.205, §15.209, §15.247(d); RSS-210 [A8.5] Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2480MHz Channel: 39 Analyzer Field Frequency Pol AFCL Limit Margin Level Detector Strength [MHz] [H/V] [dB] [dBV/m] [dB] [dBm] [dBV/m] 4960.00 -108.94 Avg H 41.17 39.23 53.98 -14.75 4960.00 -99.15 Peak H 41.17 49.02 73.98 -24.96 7440.00 -135.00 Avg H 45.11 17.11 53.98 -36.87 7440.00 -125.00 Peak H 45.11 27.11 73.98 -46.87 12400.00 -135.00 Avg H 52.81 24.81 53.98 -29.17 12400.00 -125.00 Peak H 52.81 34.81 73.98 -39.17 Table 6-6. Radiated Measurements @ 3 meters FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

6.3 Radiated Restricted Band Edge Measurements §15.205, §15.209, §15.247(d); RSS-210 [A8.5] Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2480MHz Channel: 39 Analyzer Field Frequency Pol AFCL Limit Margin Level Detector Strength [MHz] [H/V] [dB] [dBV/m] [dB] [dBm] [dBV/m] 2483.50 -101.71 Avg H 37.52 42.81 53.98 -11.17 2483.50 -98.48 Peak H 37.52 46.04 73.98 -27.94 2484.80 -97.22 Avg H 37.54 47.31 53.98 -6.67 2484.80 -88.57 Peak H 37.54 55.96 73.98 -18.02 2490.60 -98.84 Avg H 37.61 45.78 53.98 -8.20 2490.60 -90.13 Peak H 37.61 54.49 73.98 -19.49 Table 6-7. Radiated Restricted Band Edge Measurements (2483.5 – 2500MHz) FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013

7.0 CONCLUSION The data collected relate only the item(s) tested and show that the LG Portable Handset FCC ID: ZNFVS890 is in compliance with Part 15C of the FCC Rules. FCC Pt. 15.247 BLUETOOTH (LE) TEST REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 16 0Y1306100966.ZNF 06/10 - 06/14/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.7 06/10/2013


Document Created: 2013-07-11 14:22:38
Document Modified: 2013-07-11 14:22:38
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC