Part 27 LTE Test Report

FCC ID: ZNFVS890

Test Report

Download: PDF
FCCID_2014186

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 27 LTE Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 06/10 - 06/12/2013 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab., Columbia, MD, USA United States Test Report Serial No.: 0Y1306100967.ZNF FCC ID : ZNFVS890 APPLI C A NT: LG ELECTRONICS MOBILECOMM U.S.A FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part(s): §2; §27 EUT Type: Portable Handset Model(s): VS890, LG-VS890, LGVS890 Test Device Serial No.: identical prototype [S/N: EMI #2] Class II Permissive Please see FCC change documents. Change: Original Grant Date: June 14, 2013 ERP/EIRP Tx Frequency Emission Max. Mode Modulation Max. (MHz) Designator Power Power (W) (dBm) LTE Band 13 782 8M91G7D QPSK 0.085 19.28 LTE Band 13 782 8M92W7D 16QAM 0.069 18.39 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

T A B L E O F C O N T E N T S FCC PART 27 MEASUREMENT REPORT ..................................................................................................3 1.0 INTRODUCTION ..............................................................................................................................4 1.1 SCOPE ................................................................................................................................................ 4 1.2 TESTING FACILITY............................................................................................................................. 4 2.0 PRODUCT INFORMATION..............................................................................................................5 2.1 EQUIPMENT DESCRIPTION .............................................................................................................. 5 2.2 DEVICE CAPABILITIES....................................................................................................................... 5 2.3 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ........................................................................... 5 2.4 LABELING REQUIREMENTS.............................................................................................................. 5 3.0 DESCRIPTION OF TESTS ..............................................................................................................6 3.1 MEASUREMENT PROCEDURE ......................................................................................................... 6 3.1 BLOCK C FREQUENCY RANGE ........................................................................................................ 6 3.2 RADIATED POWER AND RADIATED SPURIOUS EMISSIONS ........................................................ 6 3.3 FREQUENCY STABILITY / TEMPERATURE VARIATION ................................................................. 7 4.0 TEST EQUIPMENT CALIBRATION DATA ......................................................................................8 5.0 SAMPLE CALCULATIONS ..............................................................................................................9 6.0 TEST RESULTS.............................................................................................................................10 6.1 SUMMARY......................................................................................................................................... 10 6.2 EFFECTIVE RADIATED POWER (ERP) ........................................................................................... 11 6.3 BAND 13 RADIATED SPURIOUS EMISSIONS ................................................................................ 12 BAND 13 RADIATED SPURIOUS EMISSIONS 1559 – 1610MHZ BAND..................................................... 13 6.4 BAND 13 FREQUENCY STABILITY MEASUREMENTS................................................................... 14 7.0 CONCLUSION................................................................................................................................16 FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

MEASUREMENT REPORT FCC Part 27 §2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland Mills Road, Columbia, MD 21045 USA FCC RULE PART(S): §2; §27 BASE MODEL: VS890 FCC ID: ZNFVS890 FCC CLASSIFICATION: PCS Licensed Transmitter Held to Ear (PCE) FREQUENCY TOLERANCE: ±0.00025 % (2.5 ppm) Test Device Serial No.: EMI #2 Production Pre-Production Engineering DATE(S) OF TEST: 06/10 - 06/12/2013 TEST REPORT S/N: 0Y1306100967.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451B-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 Testing Facility The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39o 10’23” N latitude and 76o 49’50” W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2003 on February 15, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFVS890. The test data contained in this report pertains only to the emissions due to the EUT’s LTE function. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A (BC0, BC1), Band 13 (10MHz BW) LTE, 802.11b/g/n WLAN, Bluetooth (1x,EDR, LE) 2.3 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. 2.4 Labeling Requirements Per 2.925 The FCC identifier shall be permanently affixed to the equipment and shall be readily visible to the purchaser at the time of purchase. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

3.0 DESCRIPTION OF TESTS 3.1 Measurement Procedure The measurement procedures described in the document titled “Land Mobile FM or PM – Communications Equipment – Measurements and Performance Standards” (ANSI/TIA-603-C-2004) and “Procedures for Compliance Measurement of the Fundamental Emission Power of Licensed Wideband (> 1 MHz) Digital Transmission Systems” (KDB 971168) were used in the measurement of the LG Portable Handset FCC ID: ZNFVS890. 3.1 Block C Frequency Range §27.5(b)(3) Two paired channels of 11 megahertz each are available for assignment in Block C in the 746-757 MHz and 776-787 MHz bands. In the event that no licenses for two channels in this Block C are assigned based on the results of the first auction in which such licenses were offered because the auction results do not satisfy the applicable reserve price, the spectrum in the 746-757 MHz and 776-787 MHz bands will instead be made available for assignment at a subsequent auction as follows: (i) Two paired channels of 6 megahertz each available for assignment in Block C1 in the 746-752 MHz and 776-782 MHz bands. (ii) Two paired channels of 5 megahertz each available for assignment in Block C2 in the 752-757 MHz and 782-787 MHz bands. 3.2 Radiated Power and Radiated Spurious Emissions §2.1053 §27.50(b.10) §27.53(f) The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An ETS Lindgren Model 2188 raised turntable is used for radiated measurement. It is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. A 78cm high PVC support structure is placed on top of the turntable. A ¾” (~1.9cm) sheet of high density polyethylene is used as the table top and is placed on top of the PVC supports to bring the total height of the table to 80cm. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Radiated power levels are also investigated with the receive antenna horizontally and vertically polarized. The maximized power level is recorded using the spectrum analyzer “Channel Power” function with the integration band set to the emissions’ occupied bandwidth, a RMS detector, RBW = 100kHz, VBW = 300kHz, and a 1 second sweep time over a minimum of 10 sweeps, per the guidelines of KDB 971168. Per the guidance of ANSI/TIA-603-C-2004, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]) specified in 22.917(a) and 24.238(a). 3.3 Frequency Stability / Temperature Variation §2.1055 §27.5(b) §27.54 The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block for Part 27. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for one minute before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A sufficient stabilization period at each temperature shall be used prior to each frequency requirement. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

4.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number - RE1 Radiated Emissions Cable Set (UHF/EHF) 3/29/2013 Annual 3/29/2014 N/A Agilent 8447D Broadband Amplifier 5/31/2013 Annual 5/31/2014 2443A01900 Espec ESX-2CA Environmental Chamber 4/16/2013 Annual 4/16/2014 17620 ETS Lindgren 3117 1-18 GHz DRG Horn (Medium) 7/22/2011 Biennial 7/22/2013 125518 Schwarzbeck UHA 9105 Dipole Antenna (400 - 1GHz) Rx 10/3/2011 Biennial 10/3/2013 91052523RX Rohde & Schwarz CMW500 LTE Radio Communication Tester 10/7/2011 Biennial 10/7/2013 103962 Mini-Circuits VHF-1200+ High Pass Filter 1/17/2013 Annual 1/17/2014 30923 Rohde & Schwarz TS-PR18 1-18 GHz Pre-Amplifier 5/31/2013 Annual 5/31/2014 100071 Rohde & Schwarz ESU26 EMI Test Receiver 2/25/2013 Annual 2/25/2014 100342 Seekonk NC-100 Torque Wrench (8" lb) 3/5/2012 Triennial 3/5/2015 N/A Sunol JB5 Bi-Log Antenna (30M - 5GHz) 1/26/2012 Biennial 1/26/2014 A051107 Table 4-1. Test Equipment FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

5.0 SAMPLE CALCULATIONS Emission Designator QPSK Modulation Emission Designator = 8M62G7D LTE BW = 8.62 MHz G = Phase Modulation 7 = Quantized/Digital Info D = Amplitude/Angle Modulated 16QAM Modulation Emission Designator = 8M45W7D LTE BW = 8.45 MHz W = Amplitude/Angle Modulated 7 = Quantized/Digital Info D = Combination (Audio/Data) Spurious Radiated Emission – LTE Band Example: Middle Channel LTE Mode 2nd Harmonic (1564 MHz) The average spectrum analyzer reading at 3 meters with the EUT on the turntable was –81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of –81.0 dBm on the spectrum analzyer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 1564 MHz. So 6.1 dB is added to the signal generator reading of –30.9 dBm yielding –24.80 dBm. The fundamental EIRP was 25.501 dBm so this harmonic was 25.501 dBm – (-24.80). FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

6.0 TEST RESULTS 6.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFVS890 FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): LTE FCC Part Test Test Description Test Limit Result Reference Section(s) Condition TRANSMITTER MODE (TX) Effective Radiated 27.50(b.10) < 3 Watts max. ERP PASS Section 6.2 Power (Band 13) > 43 + 10log10 (P[Watts]) Undesirable 2.1053 27.53(f) for all out-of-band RADIATED PASS Section, 6.3 Emissions emissions Fundamental emissions 2.1055. 27.5(b) Frequency Stability stay within authorized PASS Section, 6.4 27.54 frequency block Table 6-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

6.2 Effective Radiated Power (ERP) §27.50(b.10) Channel Substitute Antenna Frequency RB ERP ERP Margin Bandwidth Mod. Battery Level Gain Pol [H/V] [MHz] Size/Offset [dBm] [Watts] [dB] [MHz] [dBm] [dBd] 782.00 10 QPSK Standard 1/0 15.52 3.76 H 19.28 0.085 -15.49 782.00 10 16QAM Standard 1/0 14.54 3.85 H 18.39 0.069 -16.38 Table 6-2. ERP Data (Band 13) NOTES: 1. This device was tested under all bandwidths, and RB configurations, and modulations. This device was tested under all modulations, RB sizes and offsets and the worst case emissions are reported with QPSK modulation and 1RB/0 offset. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The worst case test configuration was found with the EUT in the H positioning. The data reported in the table above was measured in this test setup. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

6.3 Band 13 Radiated Spurious Emissions §2.1053 §27.53(f) OPERATING FREQUENCY: 782.00 MHz MEASURED OUTPUT POWER: 19.28 dBm = 0.085 W MODULATION SIGNAL: QPSK BANDWIDTH: 10 MHz DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 32.28 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 2346.00 -49.07 3.59 -45.48 H 64.76 3128.00 -53.97 5.20 -48.77 H 68.05 3910.00 -79.09 6.64 -72.45 H 91.73 4692.00 -78.60 7.48 -71.11 H 90.39 5474.00 -77.96 8.42 -69.54 H 88.82 Table 6-3. Radiated Spurious Data NOTES: 1. This device was tested under all bandwidths, and RB configurations, and modulations. This device was tested under all modulations, RB sizes and offsets and the worst case emissions are reported with QPSK modulation and 1RB/0 offset. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The worst case test configuration was found with the EUT in the H positioning. The data reported in the table above was measured in this test setup. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

Band 13 Radiated Spurious Emissions 1559 – 1610MHz Band §2.1053 §27.53(f) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 782.00 MHz MEASURED OUTPUT POWER: 19.281 dBm = 0.085 W MODULATION SIGNAL: QPSK DISTANCE: 3 meters NARROWBAND EMISSION LIMIT: -50 dBm WIDEBAND EMISSION LIMIT: -40 dBm/MHz LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION MARGIN EMISSION TYPE ANTENNA GAIN POL (H/V) (MHz) TERMINALS LEVEL (dB) (dBi) (dBm) (dBm) 1564.00 WIDEBAND -58.22 5.67 -52.55 H -12.55 Table 6-4. Radiated Spurious Data NOTES: 1. This device was tested under all bandwidths, and RB configurations, and modulations. This device was tested under all modulations, RB sizes and offsets and the worst case emissions are reported with QPSK modulation and 1RB/0 offset. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The worst case test configuration was found with the EUT in the H positioning. The data reported in the table above was measured in this test setup. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

6.4 Band 13 Frequency Stability Measurements §2.1055 §22.355 §27.5(b) §27.54 OPERATING FREQUENCY: 782,000,000 Hz CHANNEL: 23230 REFERENCE VOLTAGE: 3.8 VDC VOLTAGE POWER TEMP FREQUENCY Freq. Dev. Deviation (%) (VDC) (oC) (Hz) (Hz) (%) 100 % 3.80 + 20 (Ref) 782,000,011 11 0.0000014 100 % - 30 781,999,997 -3 -0.0000004 100 % - 20 782,000,024 24 0.0000031 100 % - 10 782,000,006 6 0.0000008 100 % 0 781,999,994 -6 -0.0000008 100 % + 10 781,999,972 -28 -0.0000036 100 % + 20 781,999,990 -10 -0.0000013 100 % + 30 781,999,971 -29 -0.0000037 100 % + 40 782,000,017 17 0.0000022 100 % + 50 782,000,007 7 0.0000009 115 % 4.37 + 20 781,999,989 -11 -0.0000014 BATT. ENDPOINT 3.40 + 20 781,999,977 -23 -0.0000029 Table 6-5. Frequency Stability Data (Band 13) Note: Based on the results of the frequency stability test at the center channel the frequency deviation results measured are very small. As such it is determined that the channels at the band edge would remain in- band when the maximum measured frequency deviation noted during the frequency stability tests is applied. Therefore the device is determined to remain operating in band over the temperature and voltage range as tested. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

Band 13 Frequency Stability Measurements (Cont’d) §2.1055 §22.355 §27.5(b) §27.54 Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 0 30 10 20 40 50 0 0 0 0 +2 -3 -2 -1 + + + + + Tem perature (°C) Figure 6-1. Frequency Stability Graph (Band 13) FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013

7.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFVS890 complies with all the requirements of Parts 2 and 27 of the FCC rules for LTE operation only. FCC Pt. 27 LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 16 0Y1306100967.ZNF 06/10 - 06/12/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V4.5 04/15/2013


Document Created: 2019-11-06 19:34:06
Document Modified: 2019-11-06 19:34:06
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC