Part 22-24 Test Report

FCC ID: ZNFVS890

Test Report

Download: PDF
FCCID_2014179

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 22 & 24 Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 06/10 - 06/13/2013 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab., Columbia, MD, USA United States Test Report Serial No.: 0Y1306100966.ZNF FCC ID: ZNFVS890 APPLI C A NT: LG ELECTRONICS MOBILECOMM U.S.A Application Type: Class II Permissive Change Model(s): VS890, LG-VS890, LGVS890 EUT Type: Portable Handset FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part(s): §2 §22(H) §24(E) Test Procedure(s): ANSI/TIA-603-C-2004, KDB 971168 Test Device Serial No.: identical prototype [S/N: EMI #2] Class II Permissive Change: Please see FCC change documents. Original Grant Date: June 14, 2013 ERP/EIRP Tx Frequency Emission Max. Max. Mode (MHz) Designator Power Power (W) (dBm) CDMA850 824.70 - 848.31 1M28F9W 0.189 22.76 CDMA1900 1851.25 - 1908.75 1M28F9W 0.279 24.46 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

T A B L E O F C O N T E N T S FCC PART 22 & 24 MEASUREMENT REPORT ..........................................................................................3 1.0 INTRODUCTION ..............................................................................................................................4 1.1 SCOPE ................................................................................................................................................ 4 1.2 TESTING FACILITY............................................................................................................................. 4 2.0 PRODUCT INFORMATION..............................................................................................................5 2.1 EQUIPMENT DESCRIPTION .............................................................................................................. 5 2.2 DEVICE CAPABILITIES....................................................................................................................... 5 2.3 TEST CONFIGURATION..................................................................................................................... 5 2.4 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ........................................................................... 5 3.0 DESCRIPTION OF TESTS ..............................................................................................................6 3.1 EVALUATION PROCEDURE .............................................................................................................. 6 3.2 CELLULAR - BASE FREQUENCY BLOCKS....................................................................................... 6 3.3 CELLULAR - MOBILE FREQUENCY BLOCKS................................................................................... 6 3.4 PCS - BASE FREQUENCY BLOCKS .................................................................................................. 6 3.5 PCS - MOBILE FREQUENCY BLOCKS .............................................................................................. 7 3.6 RADIATED POWER AND RADIATED SPURIOUS EMISSIONS ........................................................ 7 3.7 PEAK-AVERAGE RATIO ..................................................................................................................... 8 3.8 FREQUENCY STABILITY / TEMPERATURE VARIATION ................................................................. 8 4.0 TEST EQUIPMENT CALIBRATION DATA ......................................................................................9 5.0 SAMPLE CALCULATIONS ............................................................................................................10 6.0 TEST RESULTS.............................................................................................................................11 6.1 SUMMARY......................................................................................................................................... 11 6.2 CELLULAR EFFECTIVE RADIATED POWER (ERP) ....................................................................... 12 6.3 PCS EFFECTIVE RADIATED POWER (EIRP).................................................................................. 13 6.4 CELLULAR CDMA RADIATED MEASUREMENTS........................................................................... 14 6.5 PCS CDMA RADIATED MEASUREMENTS...................................................................................... 17 6.6 CELLULAR CDMA FREQUENCY STABILITY MEASUREMENTS ................................................... 20 6.7 PCS CDMA FREQUENCY STABILITY MEASUREMENTS............................................................... 22 7.0 CONCLUSION................................................................................................................................24 FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

MEASUREMENT REPORT FCC Part 22 & 24 §2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland Mills Road, Columbia, MD 21046 USA FCC RULE PART(S): §2 §22(H) §24(E) BASE MODEL: VS890 FCC ID: ZNFVS890 FCC CLASSIFICATION: PCS Licensed Transmitter Held to Ear (PCE) MODE: CDMA FREQUENCY TOLERANCE: ±0.00025 % (2.5 ppm) Test Device Serial No.: EMI #2 Production Pre-Production Engineering DATE(S) OF TEST: 06/10 - 06/13/2013 TEST REPORT S/N: 0Y1306100966.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451B-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 Testing Facility The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39o 10’23” N latitude and 76o 49’50” W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on February 15, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFVS890. The test data contained in this report pertains only to the emissions due to the EUT’s 2G/3G licensed transmitters. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A (BC0, BC1), Band 13 (10MHz BW) LTE, 802.11b/g/n WLAN, Bluetooth (1x,EDR, LE) 2.3 Test Configuration The LG Portable Handset FCC ID: ZNFVS890 was tested per the guidance of ANSI/TIA-603-C-2004 and KDB 971168. See Section 3.0 of this test report for a description of the radiated emissions tests. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the “Land Mobile FM or PM – Communications Equipment – Measurements and Performance Standards” (ANSI/TIA-603-C-2004) and “Procedures for Compliance Measurement of the Fundamental Emission Power of Licensed Wideband (> 1 MHz) Digital Transmission Systems” (KDB 971168) were used in the measurement of the LG Portable Handset FCC ID: ZNFVS890. Deviation from Measurement Procedure…………………………………………………………………..None 3.2 Cellular - Base Frequency Blocks §22.905 A* A B A* B* Low High 869 880 890 894 BLOCK 1: 869 – 880 MHz (A* Low + A) BLOCK 3: 890 – 891.5 MHz (A* High) BLOCK 2: 880 – 890 MHz (B) BLOCK 4: 891.5 – 894 MHz (B*) 3.3 Cellular - Mobile Frequency Blocks §22.905 A* A B A* B* Low High 824 835 845 849 BLOCK 1: 824 – 835 MHz (A* Low + A) BLOCK 3: 845 – 846.5 MHz (A* High) BLOCK 2: 835 – 845 MHz (B) BLOCK 4: 846.5 – 849 MHz (B*) 3.4 PCS - Base Frequency Blocks §24.229 A D B E F C 1930 1950 1970 1990 BLOCK 1: 1930 – 1945 MHz (A) BLOCK 4: 1965 – 1970 MHz (E) BLOCK 2: 1945 – 1950 MHz (D) BLOCK 5: 1970 – 1975 MHz (F) BLOCK 3: 1950 – 1965 MHz (B) BLOCK 6: 1975 – 1990 MHz (C) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

3.5 PCS - Mobile Frequency Blocks §24.229 A D B E F C 1850 1870 1890 1910 BLOCK 1: 1850 – 1865 MHz (A) BLOCK 4: 1885 – 1890 MHz (E) BLOCK 2: 1865 – 1870 MHz (D) BLOCK 5: 1890 – 1895 MHz (F) BLOCK 3: 1870 – 1885 MHz (B) BLOCK 6: 1895 – 1910 MHz (C) 3.6 Radiated Power and Radiated Spurious Emissions §2.1053 §22.913(a.2) §22.917(a) §24.232(c) §24.238(a) RSS-132(4.4) RSS-132(4.5.1) RSS-133(6.4) RSS-133(6.5.1) The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An ETS Lindgren Model 2188 raised turntable is used for radiated measurement. It is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. A 78cm high PVC support structure is placed on top of the turntable. A ¾” (~1.9cm) sheet of high density polyethylene is used as the table top and is placed on top of the PVC supports to bring the total height of the table to 80cm. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Radiated power levels are also investigated with the receive antenna horizontally and vertically polarized. The maximized power level is recorded using the spectrum analyzer “Channel Power” function with the integration band set to the emissions’ occupied bandwidth, a RMS detector, RBW = 100kHz, VBW = 300kHz, and a 1 second sweep time over a minimum of 10 sweeps, per the guidelines of KDB 971168. Per the guidance of ANSI/TIA-603-C-2004, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]) specified in 22.917(a) and 24.238(a). 3.7 Peak-Average Ratio §24.232(d) RSS-132(5.4) RSS-133(6.4) A peak to average ratio measurement is performed at the conducted port of the EUT. The spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For pulsed signals, the spectrum analyzer is set to use an internal “RF Burst” trigger that is synced with an incoming pulse and the measurement interval is set to less than the duration of the “on time” of one burst to ensure that energy is only captured during a time in which the transmitter is operating at maximum power. For continuous signals, the trigger is set to “free run” in the CCDF measurement mode. 3.8 Frequency Stability / Temperature Variation §2.1055 §22.355 §22.863 §22.905 §24.229 §24.235 RSS-132(4.3) RSS-133(6.3) Frequency stability testing is performed in accordance with the guidelines of ANSI/TIA-603-C-2004. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – For Part 22, the frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm) of the center frequency. For Part 24, the frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

4.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Table 4-1. Test Equipment Notes: 1. Equipment used for signaling with a calibration date of “N/A” shown in this list was only used for maintaining a link between the piece of equipment and the EUT. This equipment was not used to make direct calibrated measurements. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

5.0 SAMPLE CALCULATIONS CDMA Emission Designator Emission Designator = 1M25F9W CDMA BW = 1.25 MHz F = Frequency Modulation 9 = Composite Digital Info W = Combination (Audio/Data) (Measured at the 99.75% power bandwidth) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.0 TEST RESULTS 6.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFVS890 FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): CDMA Test FCC Part Test Referenc Test Description Test Limit Conditio Section(s) Result e n TRANSMITTER MODE (TX) 22.913(a.2) Effective Radiated Power < 7 Watts max. ERP PASS Section 6.2 Equivalent Isotropic 24.232(c) < 2 Watts max. EIRP PASS Section 6.3 Radiated Power RADIATED 2.1053 > 43 + log10 (P[Watts]) for all Sections, 22.917(a) Undesirable Emissions PASS out-of-band emissions 6.4, 6.5 24.238(a) < 2.5 ppm (Part 22) 2.1055 22.355 Sections, Frequency Stability Emission must remain in PASS 24.235 6.6, 6.7 band (Part 24) Table 6-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.2 Cellular Effective Radiated Power (ERP) §22.913(a)(2) RSS-132(4.4) [SRSP-503(5.1.3)] Substitute Antenna ERP Frequency Battery Pol ERP ERP Margin Mode Level Gain Limit [MHz] Type [H/V] [dBm] [Watts] [dB] [dBm] [dBd] [dBm] 824.70 CDMA850 Standard 16.83 4.60 V 21.43 0.139 38.45 -17.02 836.52 CDMA850 Standard 17.03 4.82 V 21.85 0.153 38.45 -16.60 848.31 CDMA850 Standard 17.72 5.04 V 22.76 0.189 38.45 -15.69 Table 6-2. ERP (Cellular CDMA) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.3 PCS Effective Radiated Power (EIRP) §22.913(a)(2) RSS-132(4.4) [SRSP-503(5.1.3)] Substitute Antenna EIRP Frequency Battery Pol EIRP EIRP Margin Mode Level Gain Limit [MHz] Type [H/V] [dBm] [Watts] [dB] [dBm] [dBi] [dBm] 1851.25 CDMA1900 Standard 14.86 9.60 H 24.46 0.279 33.01 -8.55 1880.00 CDMA1900 Standard 13.59 9.53 H 23.12 0.205 33.01 -9.89 1908.75 CDMA1900 Standard 13.38 9.47 H 22.85 0.193 33.01 -10.16 Table 6-3. EIRP (PCS CDMA) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.4 Cellular CDMA Radiated Measurements §2.1053 §22.917(a) RSS-132(4.5.1) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 824.70 MHz CHANNEL: 1013 MEASURED OUTPUT POWER: 21.43 dBm = 0.139 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log 10 (W) = 34.43 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1649.40 -55.35 2.59 -52.77 V 74.2 2474.10 -54.18 2.89 -51.29 V 72.7 3298.80 -56.71 5.45 -51.26 V 72.7 4123.50 -81.51 7.05 -74.46 V 95.9 4948.20 -80.98 7.87 -73.12 V 94.5 Table 6-4. Radiated Spurious Data (Cellular CDMA Mode – Ch. 1013) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

Cellular CDMA Radiated Measurements (Cont’d) §2.1053 §22.917(a) RSS-132(4.5.1) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 836.52 MHz CHANNEL: 384 MEASURED OUTPUT POWER: 21.85 dBm = 0.153 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 34.85 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1673.04 -54.58 2.34 -52.24 V 74.1 2509.56 -53.64 2.84 -50.81 V 72.7 3346.08 -57.01 5.64 -51.37 V 73.2 4182.60 -81.65 7.14 -74.51 V 96.4 5019.12 -81.01 7.97 -73.04 V 94.9 Table 6-5. Radiated Spurious Data (Cellular CDMA Mode – Ch. 384) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

Cellular CDMA Radiated Measurements (Cont’d) §2.1053 §22.917(a) RSS-132(4.5.1) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 848.31 MHz CHANNEL: 777 MEASURED OUTPUT POWER: 22.76 dBm = 0.189 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 35.76 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1696.62 -54.47 2.09 -52.38 V 75.1 2544.93 -54.04 3.16 -50.88 V 73.6 3393.24 -57.71 5.83 -51.88 V 74.6 4241.55 -81.79 7.24 -74.56 V 97.3 5089.86 -80.79 8.02 -72.77 V 95.5 Table 6-6. Radiated Spurious Data (Cellular CDMA Mode – Ch. 777) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.5 PCS CDMA Radiated Measurements §2.1053 §24.238(a) RSS-133(6.5.2) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1851.25 MHz CHANNEL: 25 MEASURED OUTPUT POWER: 24.46 dBm = 0.279 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 37.46 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBi) (dBm) (dBm) 3702.50 -49.85 8.40 -41.45 H 65.9 5553.75 -52.07 10.62 -41.45 H 65.9 7405.00 -51.87 11.82 -40.05 H 64.5 9256.25 -45.72 13.30 -32.43 H 56.9 11107.50 -49.58 13.50 -36.08 H 60.5 Table 6-7. Radiated Spurious Data (PCS CDMA Mode – Ch. 25) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

PCS CDMA Radiated Measurements (Cont’d) §2.1053 §24.238(a) RSS-133(6.5.2) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1880.00 MHz CHANNEL: 661 MEASURED OUTPUT POWER: 23.12 dBm = 0.205 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 36.12 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBi) (dBm) (dBm) 3760.00 -44.04 8.42 -35.61 H 58.7 5640.00 -51.83 10.66 -41.18 H 64.3 7520.00 -51.84 11.92 -39.92 H 63.0 9400.00 -50.84 13.24 -37.60 H 60.7 11280.00 -76.02 13.49 -62.53 H 85.7 Table 6-8. Radiated Spurious Data (PCS CDMA Mode – Ch. 600) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

PCS CDMA Radiated Measurements (Cont’d) §2.1053 §24.238(a) RSS-133(6.5.2) Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1908.75 MHz CHANNEL: 1175 MEASURED OUTPUT POWER: 22.85 dBm = 0.193 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 35.85 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN (dBc) (MHz) TERMINALS LEVEL (H/V) (dBi) (dBm) (dBm) 3817.50 -47.95 8.57 -39.38 H 62.2 5726.25 -50.86 10.69 -40.17 H 63.0 7635.00 -48.08 12.06 -36.02 H 58.9 9543.75 -46.59 13.20 -33.39 H 56.2 11452.50 -75.95 13.42 -62.53 H 85.4 Table 6-9. Radiated Spurious Data (PCS CDMA Mode – Ch. 1175) NOTES: 1) This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The data reported in the table above was measured in this test setup. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.6 Cellular CDMA Frequency Stability Measurements §2.1055 §22.355 RSS-132(4.3) OPERATING FREQUENCY: 836,520,000 Hz CHANNEL: 384 REFERENCE VOLTAGE: 3.8 VDC DEVIATION LIMIT: ± 0.00025 % or 2.5 ppm VOLTAGE POWER TEMP FREQUENCY Freq. Dev. Deviation (%) (VDC) (oC) (Hz) (Hz) (%) 100 % 3.80 + 20 (Ref) 836,520,022 22 0.0000026 100 % - 30 836,520,020 20 0.0000024 100 % - 20 836,519,998 -2 -0.0000002 100 % - 10 836,520,000 0 0.0000000 100 % 0 836,520,010 10 0.0000012 100 % + 10 836,520,026 26 0.0000031 100 % + 20 836,520,016 16 0.0000019 100 % + 30 836,519,987 -13 -0.0000016 100 % + 40 836,519,995 -5 -0.0000006 100 % + 50 836,520,006 6 0.0000007 115 % 4.37 + 20 836,519,971 -29 -0.0000035 BATT. ENDPOINT 3.25 + 20 836,519,983 -17 -0.0000020 Table 6-10. Frequency Stability Data (Cellular CDMA Mode – Ch. 384) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 20 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

Cellular CDMA Frequency Stability Measurements (Cont’d) §2.1055 §22.355 RSS-132(4.3) Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 30 20 10 20 40 50 0 0 0 0 -3 -2 -1 + + + + + + Tem perature (°C) Figure 6-1. Frequency Stability Graph (Cellular CDMA Mode – Ch. 384) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 21 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

6.7 PCS CDMA Frequency Stability Measurements §2.1055 §24.235 RSS-139(6.3) OPERATING FREQUENCY: 1,880,000,000 Hz CHANNEL: 661 REFERENCE VOLTAGE: 3.8 VDC VOLTAGE POWER TEMP FREQUENCY Freq. Dev. Deviation (%) (VDC) (oC) (Hz) (Hz) (%) 100 % 3.80 + 20 (Ref) 1,879,999,973 -27 -0.0000014 100 % - 30 1,879,999,990 -10 -0.0000005 100 % - 20 1,880,000,021 21 0.0000011 100 % - 10 1,879,999,982 -18 -0.0000010 100 % 0 1,880,000,024 24 0.0000013 100 % + 10 1,880,000,011 11 0.0000006 100 % + 20 1,880,000,009 9 0.0000005 100 % + 30 1,880,000,029 29 0.0000015 100 % + 40 1,880,000,020 20 0.0000011 100 % + 50 1,880,000,007 7 0.0000004 115 % 4.37 + 20 1,879,999,988 -12 -0.0000006 BATT. ENDPOINT 3.25 + 20 1,880,000,015 15 0.0000008 Table 6-11. Frequency Stability Data (PCS CDMA Mode – Ch. 600) Note: Based on the results of the frequency stability test at the center channel the frequency deviation results measured are very small. As such it is determined that the channels at the band edge would remain in- band when the maximum measured frequency deviation noted during the frequency stability tests is applied. Therefore the device is determined to remain operating in band over the temperature and voltage range as tested. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

PCS CDMA Frequency Stability Measurements (Cont’d) §2.1055 §24.235 RSS-139(6.3) Frequency Stability 1.5 1.0 0.5 Deviation (ppm) 0.0 -0.5 -1.0 -1.5 30 20 10 20 40 50 0 0 0 0 -3 -2 -1 + + + + + + Tem perature (°C) Figure 6-2. Frequency Stability Graph (PCS CDMA Mode – Ch. 600) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013

7.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFVS890 complies with all the requirements of Parts 2, 22, 24 of the FCC rules. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFVS890 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 24 of 24 0Y1306100966.ZNF 06/10 - 06/13/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. V 2.9 04/15/2013


Document Created: 2019-10-29 18:20:01
Document Modified: 2019-10-29 18:20:01
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC