16I22629-S1V4 FCC Report SAR C2PC

FCC ID: ZNFVC200

RF Exposure Info

Download: PDF

FCCID_2906237

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

Revision History
Rev. Date Revisions Revised By
V1 1/26/2016 Initial Issue --
V2 2/2/2016 Section 10: Updated Body-worn Test Distance Devin Chang
V3 2/10/2016 Section 7: Removed statement Coltyce Sanders
Updated Model Name
V4 2/15/2016 Coltyce Sanders
Appendix A: Updated Antenna Distance and Location Diagram

Page 2 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

Table of Contents

1. Attestation of Test Results ......................................................................................................... 5

2. Test Specification, Methods and Procedures............................................................................ 6

3. Facilities and Accreditation ........................................................................................................ 6

4. SAR Measurement System & Test Equipment .......................................................................... 7
4.1. SAR Measurement System ........................................................................................................ 7
4.2. SAR Scan Procedures ............................................................................................................... 8
4.3. Test Equipment........................................................................................................................ 10

5. Measurement Uncertainty ......................................................................................................... 10

6. Device Under Test (DUT) Information ...................................................................................... 11
6.1. DUT Description ...................................................................................................................... 11
6.2. Wireless Technologies ............................................................................................................. 11
6.3. Nominal and Maximum Output Power...................................................................................... 11

7. RF Exposure Conditions (Test Configurations) ...................................................................... 11

8. Dielectric Property Measurements & System Check .............................................................. 12
8.1. Dielectric Property Measurements ........................................................................................... 12
8.2. System Check.......................................................................................................................... 14

9. Conducted Output Power Measurements................................................................................ 15
9.1. CDMA ...................................................................................................................................... 15
9.2. Wi-Fi 2.4GHz (DTS Band) ....................................................................................................... 15
9.3. Bluetooth ................................................................................................................................. 15

10. Measured and Reported (Scaled) SAR Results ....................................................................... 16
10.1. CDMA BC0........................................................................................................................... 16
10.2. CDMA BC1........................................................................................................................... 16
10.3. Wi-Fi (DTS Band) and Bluetooth .......................................................................................... 17

11. SAR Measurement Variability ................................................................................................... 19

12. Simultaneous Transmission SAR Analysis ............................................................................. 20
12.1. Sum of the SAR for WWAN & Wi-Fi & BT............................................................................. 20

Appendixes .......................................................................................................................................... 21
16I22629-S1V2 SAR_App A Photos & Ant. Locations ........................................................................ 21
16I22629-S1V1 SAR_App B System Check Plots .............................................................................. 21
16I22629-S1V1 SAR_App C Highest Test Plots ................................................................................. 21
16I22629-S1V1 SAR_App D Tissue Ingredients................................................................................. 21
Page 3 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

2. Test Specification, Methods and Procedures
The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE STD 1528-
2013, the following FCC Published RF exposure KDB procedures:
o 248227 D01 802.11 Wi-Fi SAR v02r01
o 447498 D01 General RF Exposure Guidance v05r02
o 690783 D01 SAR Listings on Grants v01r03
o 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04
o 865664 D02 RF Exposure Reporting v01r01
o 941225 D01 3G SAR Procedures v03

3. Facilities and Accreditation
The test sites and measurement facilities used to collect data are located at

47173 Benicia Street 47266 Benicia Street
SAR Lab A SAR Lab 1
SAR Lab B SAR Lab 2
SAR Lab C SAR Lab 3
SAR Lab D SAR Lab 4
SAR Lab E
SAR Lab F
SAR Lab G
SAR Lab H

UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0.

Page 6 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

6. Device Under Test (DUT) Information
6.1. DUT Description
Overall (Length x Width): 124 mm x 47mm
Device Dimension Overall Diagonal: 126mm
Display Diagonal: 45 mm
Back Cover The rechargeable battery is not user accessible.
Battery Options The rechargeable battery is not user accessible.
Wireless Router (Hotspot) NOT SUPPORTED
Wi-Fi Direct NOT SUPPORTED
Test sample information N/A

6.2. Wireless Technologies
Wireless Duty Cycle used for SAR
Frequency bands Operating mode
technologies testing
BC0
CDMA (CDMA2000) 1xRTT (Voice & Data) 100%
BC1
802.11b
Wi-Fi 2.4 GHz 100%
802.11g
Bluetooth 2.4 GHz Version 4.0 LE 77.5% (DH5)

6.3. Nominal and Maximum Output Power
KDB 447498 sec.4.1.(3) at the maximum rated output power and within the tune-up tolerance range specified for
the product, but not more than 2 dB lower than the maximum tune-up tolerance limit

Upper limit (dB): -1.5 ~ 0.5 Max. RF Output Pow er (dBm)
Max. tune-up
RF Air interface Mode Target
tolerance limit
CDMA BC0 1xRTT 23.7 24.2
CDMA BC1 1xRTT 21.2 21.7
Upper limit (dB): 1.0 Max. RF Output Pow er (dBm)
Max. tune-up
RF Air interface Mode Target
tolerance limit
802.11b 6.0 7.0
WiFi 2.4 GHz
802.11g 5.0 6.0
Bluetooth 8.0 9.0
Bluetooth LE 7.0 8.0

7. RF Exposure Conditions (Test Configurations)
Refer to “SAR Photos and Ant locations” Appendix for the specific details of the antenna-to-antenna and
antenna-to-edge(s) distances.

Wireless RF Exposure DUT-to-User Test Antenna-to- SAR
technologies Conditions Separation Position edge/surface Required
Body-worn 0 Flat N/A Yes
WLAN
Next to Mouth 10 Flat N/A Yes

Page 11 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

8. Dielectric Property Measurements & System Check
8.1. Dielectric Property Measurements
The temperature of the tissue-equivalent medium used during measurement must also be within 18C to 25C and
within ± 2C of the temperature when the tissue parameters are characterized.
The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR
measurements. The parameters should be re-measured after each 3 – 4 days of use; or earlier if the dielectric
parameters can become out of tolerance; for example, when the parameters are marginal at the beginning of the
measurement series.
Tissue dielectric parameters were measured at the low, middle and high frequency of each operating frequency
range of the test device.

Tissue Dielectric Parameters
FCC KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz
Head Body
Target Frequency (MHz)
er s (S/m) er s (S/m)
150 52.3 0.76 61.9 0.80
300 45.3 0.87 58.2 0.92
450 43.5 0.87 56.7 0.94
835 41.5 0.90 55.2 0.97
900 41.5 0.97 55.0 1.05
915 41.5 0.98 55.0 1.06
1450 40.5 1.20 54.0 1.30
1610 40.3 1.29 53.8 1.40
1800 – 2000 40.0 1.40 53.3 1.52
2450 39.2 1.80 52.7 1.95
3000 38.5 2.40 52.0 2.73
5000 36.2 4.45 49.3 5.07
5100 36.1 4.55 49.1 5.18
5200 36.0 4.66 49.0 5.30
5300 35.9 4.76 48.9 5.42
5400 35.8 4.86 48.7 5.53
5500 35.6 4.96 48.6 5.65
5600 35.5 5.07 48.5 5.77
5700 35.4 5.17 48.3 5.88
5800 35.3 5.27 48.2 6.00

IEEE Std 1528-2013
Refer to Table 3 within the IEEE Std 1528-2013

Page 12 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016
Dielectric Property Measurements Results:

SAR Lab 1
Date Freq. (MHz) Liquid Parameters Measured Target Delta (%) Limit ±(%)
e' 41.9500 Relative Permittivity (єr): 41.95 41.50 1.08 5
Head 835
e" 19.8900 Conductivity (σ): 0.92 0.90 2.61 5
e' 42.1300 Relative Permittivity (єr): 42.13 41.60 1.27 5
1/11/2016 Head 820
e" 19.8500 Conductivity (σ): 0.91 0.90 0.73 5
e' 41.7800 Relative Permittivity (єr): 41.78 41.50 0.67 5
Head 850
e" 19.8600 Conductivity (σ): 0.94 0.92 2.58 5
e' 54.0200 Relative Permittivity (єr): 54.02 55.20 -2.14 5
Body 835
e" 21.8800 Conductivity (σ): 1.02 0.97 4.73 5
e' 54.2100 Relative Permittivity (єr): 54.21 55.28 -1.93 5
1/11/2016 Body 820
e" 21.9200 Conductivity (σ): 1.00 0.97 3.20 5
e' 53.9100 Relative Permittivity (єr): 53.91 55.16 -2.26 5
Body 850
e" 21.8300 Conductivity (σ): 1.03 0.99 4.52 5
SAR Lab 3
Date Freq. (MHz) Liquid Parameters Measured Target Delta (%) Limit ±(%)
e' 39.0200 Relative Permittivity (єr): 39.02 40.00 -2.45 5
Head 1900
e" 13.3900 Conductivity (σ): 1.41 1.40 1.04 5
e' 39.3100 Relative Permittivity (єr): 39.31 40.00 -1.72 5
1/10/2016 Head 1850
e" 13.2500 Conductivity (σ): 1.36 1.40 -2.64 5
e' 38.9900 Relative Permittivity (єr): 38.99 40.00 -2.53 5
Head 1910
e" 13.4700 Conductivity (σ): 1.43 1.40 2.18 5
e' 51.9600 Relative Permittivity (єr): 51.96 53.30 -2.51 5
Body 1900
e" 14.6500 Conductivity (σ): 1.55 1.52 1.82 5
e' 52.1600 Relative Permittivity (єr): 52.16 53.30 -2.14 5
1/10/2016 Body 1850
e" 14.4100 Conductivity (σ): 1.48 1.52 -2.48 5
e' 51.9200 Relative Permittivity (єr): 51.92 53.30 -2.59 5
Body 1910
e" 14.6600 Conductivity (σ): 1.56 1.52 2.43 5

Page 13 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

9. Conducted Output Power Measurements
9.1. CDMA
CDMA BC0 Measured Results
Freq. Ave. Pwr
Band Mode Ch No.
(MHz) (dBm)
1013 824.70 24.0
RC1 SO55
384 836.52 24.2
(Loopback)
777 848.31 24.0
1013 824.70 24.0
RC3 SO55
BC 0 1xRTT 384 836.52 24.2
(Loopback)
777 848.31 23.9
1013 824.70 24.0
RC3 SO32
384 836.52 24.2
(+F-SCH)
777 848.31 23.9

CDMA BC1 Measured Results
Freq. Ave. Pwr
Band Mode Ch No.
(MHz) (dBm)
25 1851.25 21.7
RC1 SO55
600 1880.00 21.7
(Loopback)
1175 1908.75 21.7
25 1851.25 21.7
RC3 SO55
BC 1 1xRTT 600 1880.00 21.7
(Loopback)
1175 1908.75 21.7
25 1851.25 21.7
RC3 SO32
600 1880.00 21.7
(+F-SCH)
1175 1908.75 21.7

9.2. Wi-Fi 2.4GHz (DTS Band)
Maximum tune-up tolerance limit is 7.00 dBm. This power level qualifies for exclusion of SAR testing. Please refer
to Section 10.3 for further details.

9.3. Bluetooth
Maximum tune-up tolerance limit is 9.00 dBm. This power level qualifies for exclusion of SAR testing. Please refer
to Section 10.3 for further details.

Page 15 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

10. Measured and Reported (Scaled) SAR Results
SAR Test Reduction criteria are as follows:

KDB 447498 D01 General RF Exposure Guidance:
Testing of other required channels within the operating mode of a frequency band is not required when the reported 1-g or 10-g
SAR for the mid-band or highest output power channel is:
 ≤ 0.8 W/kg or 2.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≤ 100 MHz
 ≤ 0.6 W/kg or 1.5 W/kg, for 1-g or 10-g respectively, when the transmission band is between 100 MHz and 200 MHz
 ≤ 0.4 W/kg or 1.0 W/kg, for 1-g or 10-g respectively, when the transmission band is ≥ 200 MHz

KDB 941225 D01 SAR test for 3G devices:
When the maximum output power and tune-up tolerance specified for production units in a secondary mode is ≤ ¼ dB higher
than the primary mode or when the highest reported SAR of the primary mode is scaled by the ratio of specified maximum
output power and tune-up tolerance of secondary to primary mode and the adjusted SAR is ≤ 1.2 W/kg, SAR measurement is
not required for the secondary mode

10.1. CDMA BC0
Power (dBm) 1-g SAR (W/kg)
RF Exposure Dist. Freq. Plot
Mode Test Position Ch #. Tune-up
Conditions (mm) (MHz) Meas. Meas. Scaled No.
limit
1xRTT
Body-worn 0 Flat 384 836.5 24.2 24.2 0.777 0.777 1
(RC3 SO32)
1xRTT
Next - to - Mouth 10 Flat 384 836.5 24.2 24.2 0.679 0.679 2
(RC3 SO55)

10.2. CDMA BC1
Power (dBm) 1-g SAR (W/kg)
RF Exposure Dist. Freq. Plot
Mode Test Position Ch #. Tune-up
Conditions (mm) (MHz) Meas. Meas. Scaled No.
limit
1xRTT
Body-worn 0 Flat 600 1880.0 21.7 21.7 0.539 0.539 3
(RC3 SO32)
1xRTT
Next - to - Mouth 10 Flat 600 1880.0 21.7 21.7 0.320 0.320 4
(RC3 SO55)

Page 16 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

10.3. Wi-Fi (DTS Band) and Bluetooth
Standalone SAR Test Exclusion Considerations & Estimated SAR
The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances
≤ 50 mm are determined by:
[(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)] ≤ 3.0, for 1-g SAR
and ≤ 7.5 for 10-g extremity SAR, where
 f(GHz) is the RF channel transmit frequency in GHz
 Power and distance are rounded to the nearest mW and mm before calculation
 The result is rounded to one decimal place for comparison
The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for
transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a
distance of 5 mm is applied to determine SAR test exclusion.

When the standalone SAR test exclusion is applied to an antenna that transmits simultaneously with other
antennas, the standalone SAR must be estimated according to following to determine simultaneous transmission
SAR test exclusion:
 (max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg for test
separation distances ≤ 50 mm;
where x = 7.5 for 1-g SAR, and x = 18.75 for 10-g SAR.
 0.4 W/kg for 1-g SAR and 1.0 W/kg for 10-g SAR, when the test separation distances is > 50 mm.

Body-worn:

WLAN
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Position 1-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
7.0 5 5 2.462 1.6 Flat 0.209

Conclusion:
*: The computed value is < 3; therefore, Bluetooth qualifies for Standalone SAR test exclusion.

Bluetooth
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Position 1-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
9.0 8 5 2.480 2.5 Flat 0.336

Conclusion:
*: The computed value is < 3; therefore, Bluetooth qualifies for Standalone SAR test exclusion.

Page 17 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016
Next to Mouth:

WLAN
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Position 1-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
7.0 5 10 2.462 0.8 Flat 0.105
Conclusion:
*: The computed value is ≤ 3; therefore, Wi-Fi 2.4GHz qualifies for Next to Mouth SAR test exclusion.

Bluetooth
Max. tune-up tolerance limit Min. test Frequency SAR test Test Estimated
separation (GHz) exclusion Position 1-g SAR
(dBm) (mW) distance (mm) Result* (W/kg)
9.0 8 10 2.462 1.3 Flat 0.167
Conclusion:
*: The computed value is ≤ 3; therefore, Bluetooth qualifies for Next to Mouth SAR test exclusion.

Page 18 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

11. SAR Measurement Variability
In accordance with published RF Exposure KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. These
additional measurements are repeated after the completion of all measurements requiring the same head or body
tissue-equivalent medium in a frequency band. The test device should be returned to ambient conditions (normal
room temperature) with the battery fully charged before it is re-mounted on the device holder for the repeated
measurement(s) to minimize any unexpected variations in the repeated results.

1) Repeated measurement is not required when the original highest measured SAR is < 0.80 W/kg; steps 2)
through 4) do not apply.
2) When the original highest measured SAR is ≥ 0.80 W/kg, repeat that measurement once.
3) Perform a second repeated measurement only if the ratio of largest to smallest SAR for the original and first
repeated measurements is > 1.20 or when the original or repeated measurement is ≥ 1.45 W/kg (~ 10% from
the 1-g SAR limit).
4) Perform a third repeated measurement only if the original, first or second repeated measurement is ≥1.5 W/kg
and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20.

Frequency Repeated Highest
Band Air Interface RF Exposure Conditions Test Position SAR Measured
(MHz) (Yes/No) SAR (W/kg)

850 CDMA BC0 Body-worn Flat No 0.777
1900 CDMA BC1 Next to Mouth Flat No 0.679
Note(s):
Repeated Measurement is not required since the SAR for the original measurement is not > 0.8 W/kg.

Page 19 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Report No.: 16I22629-S1V4 Issue Date: 2/15/2016

12. Simultaneous Transmission SAR Analysis
Simultaneous Transmission Condition
RF Exposure Condition Item Capable Transmit Configurations
Next to Mouth 1 CDMA + DTS
2 CDMA + DTS
Body-w orn
3 CDMA + BT
Notes:
1. CDMA (BC0/BC1) only.
2. Wi-Fi Hotspot and Wi-Fi Direct is not supported.
3. VoIP is not supported.
4. Bluetooth and Wi-Fi can not transmit simultabeously

12.1. Sum of the SAR for WWAN & Wi-Fi & BT
ᬅ+ᬆ ᬅ+ᬇ
WWAN + DTS WWAN + BT
RF Exposure Test ༃ ༄ ༅
∑ 1-g ∑ 1-g
conditions Position WWAN DTS BT SPLSR SPLSR
SAR SAR
(Yes/ No) (Yes/ No)
(mW/g) (mW/g)
Body-w orn Flat 0.777 0.209 0.336 0.986 No 1.113 No
Next To Mouth Flat 0.679 0.105 0.167 0.784 No 0.846 No

Conclusion:
Simultaneous transmission SAR measurement (Volume Scan) is not required because the sum of the 1-g SAR is < 1.6.

Page 20 of 21
UL Verification Services Inc. Doc. No.: 1.0
This report shall not be reproduced without the written approval of UL Verification Services Inc.

Document Created: 2017-11-18 14:20:15
Document Modified: 2017-11-18 14:20:15

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC