RF Exposure Info 4

FCC ID: ZNFQ720PS

RF Exposure Info

Download: PDF
FCCID_4300461

Figure D-3 750MHz Head Tissue Equivalent Matter Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 3 of 6 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

Figure D-4 Composition of 2.4 GHz Head Tissue Equivalent Matter Note: 2.4 GHz head liquid recipes are proprietary SPEAG. Since the composition is approximate to the actual liquids utilized, the manufacturer tissue-equivalent liquid data sheets are provided below. Figure D-5 2.4 GHz Head Tissue Equivalent Matter Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 4 of 6 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

Figure D-6 Composition of 5 GHz Head Tissue Equivalent Matter Note: 5 GHz head liquid recipes are proprietary SPEAG. Since the composition is approximate to the actual liquids utilized, the manufacturer tissue-equivalent liquid data sheets are provided below. Figure D-7 5 GHz Head Tissue Equivalent Matter Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 5 of 6 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

Figure D-8 Composition of 5 GHz Body Tissue Equivalent Matter Note: 5 GHz Body liquid recipes are proprietary SPEAG. Since the composition is approximate to the actual liquids utilized, the manufacturer tissue-equivalent liquid data sheets are provided below. Figure D-9 5 GHz Body Tissue Equivalent Matter Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 6 of 6 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

APPENDIX D: SAR SYSTEM VALIDATION Per FCC KDB Publication 865664 D02v01r02, SAR system validation status should be documented to confirm measurement accuracy. The SAR systems (including SAR probes, system components and software versions) used for this device were validated against its performance specifications prior to the SAR measurements. Reference dipoles were used with the required tissue- equivalent media for system validation, according to the procedures outlined in FCC KDB Publication 865664 D01v01r04 and IEEE 1528-2013. Since SAR probe calibrations are frequency dependent, each probe calibration point was validated at a frequency within the valid frequency range of the probe calibration point, using the system that normally operates with the probe for routine SAR measurements and according to the required tissue-equivalent media. A tabulated summary of the system validation status including the validation date(s), measurement frequencies, SAR probes and tissue dielectric parameters has been included. Table D-1 SAR System Validation Summary – 1g CW VALIDATION MOD. VALIDATION SAR Freq. Probe Cond. Perm. Date Probe Cal Point System (MHz) SN (σ) (εr) SENSITIVITY PROBE PROBE MOD. DUTY PAR LINEARITY ISOTROPY TYPE FACTOR H 750 9/5/2018 7409 750 Head 0.887 41.85 PASS PASS PASS N/A N/A N/A D 750 4/12/2019 3914 750 Head 0.903 42.79 PASS PASS PASS N/A N/A N/A D 835 4/12/2019 3914 835 Head 0.935 42.55 PASS PASS PASS GMSK PASS N/A H 1750 7/16/2018 7409 1750 Head 1.331 41.19 PASS PASS PASS N/A N/A N/A G 1900 8/9/2018 7410 1900 Head 1.429 38.61 PASS PASS PASS GMSK PASS N/A E 1900 3/11/2019 3589 1900 Head 1.436 39.62 PASS PASS PASS GMSK PASS N/A L 2450 4/29/2019 7308 2450 Head 1.82 37.75 PASS PASS PASS OFDM/TDD PASS PASS E 2450 2/5/2019 3589 2450 Head 1.825 39.84 PASS PASS PASS OFDM/TDD PASS PASS E 2600 2/7/2019 3589 2600 Head 1.964 40.46 PASS PASS PASS TDD PASS N/A H 5250 7/5/2018 7409 5250 Head 4.492 34.99 PASS PASS PASS OFDM N/A PASS H 5600 7/5/2018 7409 5600 Head 4.839 34.5 PASS PASS PASS OFDM N/A PASS H 5750 7/5/2018 7409 5750 Head 4.995 34.29 PASS PASS PASS OFDM N/A PASS L 750 11/6/2018 7308 750 Body 0.962 53.92 PASS PASS PASS N/A N/A N/A J 835 3/10/2019 7488 835 Body 0.988 53.87 PASS PASS PASS GMSK PASS N/A D 1750 4/29/2019 3914 1750 Body 1.529 51.89 PASS PASS PASS N/A N/A N/A I 1900 4/29/2019 7357 1900 Body 1.584 51.77 PASS PASS PASS GMSK PASS N/A G 1900 8/10/2018 7410 1900 Body 1.567 52.24 PASS PASS PASS GMSK PASS N/A K 2450 3/6/2019 7417 2450 Body 2.039 50.67 PASS PASS PASS OFDM/TDD PASS PASS K 2600 3/6/2019 7417 2600 Body 2.224 50.17 PASS PASS PASS TDD PASS N/A L 5250 10/29/2018 7308 5250 Body 5.511 48.77 PASS PASS PASS OFDM N/A PASS L 5600 10/29/2018 7308 5600 Body 5.994 48.2 PASS PASS PASS OFDM N/A PASS L 5750 10/29/2018 7308 5750 Body 6.219 47.96 PASS PASS PASS OFDM N/A PASS Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 1 of 2 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

Table D-2 SAR System Validation Summary – 10g CW VALIDATION MOD. VALIDATION SAR Freq. Probe Cond. Perm. Date Probe Cal Point PROBE PROBE MOD. DUTY System (MHz) SN (σ) (εr) SENSITIVITY PAR LINEARITY ISOTROPY TYPE FACTOR G 1900 8/10/2018 7410 1900 Body 1.567 52.239 PASS PASS PASS GMSK PASS N/A I 1900 4/29/2019 7357 1900 Body 1.584 51.771 PASS PASS PASS GMSK PASS N/A K 2450 3/6/2019 7417 2450 Body 2.039 50.67 PASS PASS PASS OFDM/TDD PASS PASS K 2600 3/6/2019 7417 2600 Body 2.224 50.17 PASS PASS PASS TDD PASS N/A L 5250 10/29/2018 7308 5250 Body 5.511 48.77 PASS PASS PASS OFDM N/A PASS L 5750 10/29/2018 7308 5750 Body 6.219 47.96 PASS PASS PASS OFDM N/A PASS NOTE: While the probes have been calibrated for both CW and modulated signals, all measurements were performed using communication systems calibrated for CW signals only. Modulations in the table above represent test configurations for which the measurement system has been validated per FCC KDB Publication 865664 D01v01r04 for scenarios when CW probe calibrations are used with other signal types. SAR systems were validated for modulated signals with a periodic duty cycle, such as GMSK, or with a high peak to average ratio (>5 dB), such as OFDM according to FCC KDB Publication 865664 D01v01r04 Approved by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX D: 04/21/19 - 05/15/19 Portable Handset Page 2 of 2 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

APPENDIX G POWER REDUCTION VERIFICATION Per the May 2017 TCBC Workshop Notes, demonstration of proper functioning of the power reduction mechanisms is required to support the corresponding SAR configurations. The verification process was divided into two parts: (1) evaluation of output power levels for individual or multiple triggering mechanisms and (2) evaluation of the triggering distances for proximity-based sensors. G.1 Power Verification Procedure The power verification was performed according to the following procedure: 1. A base station simulator was used to establish a conducted RF connection and the output power was monitored. The power measurements were confirmed to be within expected tolerances for all states before and after a power reduction mechanism was triggered. 2. Step 1 was repeated for all relevant modes and frequency bands for the mechanism being investigated. 3. Steps 1 and 2 were repeated for all individual power reduction mechanisms and combinations thereof. For the combination cases, one mechanism was switched to a 'triggered' state at a time; powers were confirmed to be within tolerances after each additional mechanism was activated. G.2 Distance Verification Procedure The distance verification procedure was performed according to the following procedure: 1. A base station simulator was used to establish an RF connection and to monitor the power levels. The device being tested was placed below the relevant section of the phantom with the relevant side or edge of the device facing toward the phantom. 2. The device was moved toward and away from the phantom to determine the distance at which the mechanism triggers and the output power is reduced, per KDB Publication 616217 D04v01r02 and FCC Guidance. Each applicable test position was evaluated. The distances were confirmed to be the same or larger (more conservative) than the minimum distances provided by the manufacturer. 3. Steps 1 and 2 were repeated for low, mid, and high bands, as appropriate (see note below Table G-2 for more details). 4. Steps 1 through 3 were repeated for all distance-based power reduction mechanisms. Reviewed by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX G: 04/21/19 – 05/15/19 Portable Handset Page 1 of 2 © 2019 PCTEST Engineering Laboratory, Inc. REV 20.05 M 11/15/2017

G.3 Main Antenna Verification Summary Table G-1 Power Measurement Verification for Main Antenna Mechanism(s) Conducted Power (dBm) Mode/Band Un‐triggered Mechanism #1 1st (Max) (Reduced) Grip UMTS 1900 23.76 23.21 Grip PCS CDMA 24.03 22.74 Grip LTE FDD Band 2 23.66 23.15 Grip LTE FDD Band 25 23.78 23.31 Grip LTE TDD Band 41 (PC3) 24.87 22.99 Grip LTE TDD Band 41 (PC2) 27.7 25.69 Table G-2 Distance Measurement Verification for Main Antenna Distance Measurements (mm) Minimum Distance per Mechanism(s) Test Condition Band Moving Toward Moving Away Manufacturer (mm) Grip Phablet ‐ Back Side Mid 2 4 2 Grip Phablet ‐ Back Side High 2 4 2 Grip Phablet ‐ Front Side Mid 2 4 2 Grip Phablet ‐ Front Side High 2 4 2 Grip Phablet ‐ Bottom Edge Mid 5 7 4 Grip Phablet ‐ Bottom Edge High 5 7 4 *Note: Mid band refers to: PCS CDMA, UMTS B2, LTE B2/25; High band refers to: LTE 41 PC3/PC2 G.4 WIFI Verification Summary Table G-3 Power Measurement Verification WIFI Mechanism(s) Conducted Power (dBm) Mode/Band Un‐triggered Mechanism #1 1st (Max) (Reduced) Held‐to‐Ear 802.11b 20.48 18.34 Held‐to‐Ear 802.11a 17.64 16.83 Held‐to‐Ear 802.11n (5GHz, 20MHz BW) 17.72 16.75 Reviewed by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX G: 04/21/19 – 05/15/19 Portable Handset Page 2 of 2 © 2019 PCTEST Engineering Laboratory, Inc. REV 20.05 M 11/15/2017

APPENDIX H: DOWNLINK LTE CA RF CONDUCTED POWERS 1.1 LTE Downlink Only Carrier Aggregation Test Reduction Methodology SAR test exclusion for LTE downlink Carrier Aggregation is determined by power measurements according to the number of component carriers (CCs) supported by the product implementation. Per April 2018 TCBC Workshop Notes, the following test reduction methodology was applied to determine the combinations required for conducted power measurements. LTE DLCA Test Reduction Methodology:  The supported combinations were arranged by the number of component carriers in columns.  Any limitations on the PCC or SCC for each combination were identified alongside the combination (e.g. CA_2A-2A-4A-12A, but B12 can only be configured as a SCC).  Power measurements were performed for "supersets" (LTE CA combinations with multiple components carriers) and any "subsets" (LTE CA combinations with fewer component carriers) that were not completely covered by the supersets.  Only subsets that have the exact same components as a superset were excluded for measurement.  When there were certain restrictions on component carriers that existed in the superset that were not applied for the subset, the subset configuration was additionally evaluated.  Both inter-band and intra-band downlink carrier aggregation scenarios were considered. Table 1 – Example of Exclusion Table for SISO Configurations Supported Channel Bandwidth [MHz] Supported Channel Bandwidth [MHz] Completely Covered Supported Channel Bandwidth [MHz] Completely Covered Supported Channel Bandwidth [MHz] Completely Covered by Completely Covered by Index 2CC Restriction Index 3CC Restriction by Measurement Index 4CC Restriction by Measurement Index 5CC Restriction Measurement Superset Measurement Superset CC1 CC2 CC1 CC2 CC3 Superset CC1 CC2 CC3 CC4 Superset CC1 CC2 CC3 CC4 CC5 2CC #1 CA_2C 5, 10, 15, 20 5, 10, 15, 20 3CC #4 3CC #1 CA_2A‐2A‐4A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 4CC #1 4CC #1 CA_2A‐2A‐4A‐5A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 5, 10 No 5CC #1 CA_2A‐5B‐30A‐66A 5, 10, 15, 20 5, 10 5, 10 5, 10 5, 10, 15, 20 No 2CC #2 CA_2A‐5A 5, 10, 15, 20 5, 10 4CC #1 3CC #2 CA_2A‐2A‐5A 5, 10, 15, 20 5, 10, 15, 20 5, 10 4CC #1 4CC #2 CA_2A‐2A‐4A‐12A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 5, 10 B12 SCC Only No 5CC #2 CA_2A‐5B‐66A‐66A 5, 10, 15, 20 5, 10 5, 10 5, 10, 15, 20 5, 10, 15, 20 No 2CC #3 CA_2A‐12A 5, 10, 15, 20 5, 10 3CC #3 3CC #3 CA_2A‐2A‐12A 5, 10, 15, 20 5, 10, 15, 20 5, 10 No 4CC #3 CA_2A‐2A‐5A‐30A 5, 10, 15, 20 5, 10, 15, 20 5, 10 5, 10 No 2CC #4 CA_2A‐13A 5, 10, 15, 20 10 3CC #9 3CC #4 CA_2C‐66A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 4CC #4 CA_2A‐2A‐5A‐66A 5, 10, 15, 20 5, 10, 15, 20 5, 10 5, 10, 15, 20 No 2CC #5 CA_2A‐17A 5, 10 5, 10 No 3CC #5 CA_2A‐2A‐71A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 4CC #5 CA_2A‐5B‐30A 5, 10, 15, 20 5, 10 5, 10 5, 10 5CC #1 2CC #6 CA_2A‐30A 5, 10, 15, 20 5, 10 3CC #14 3CC #6 CA_2A‐4A‐4A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 4CC #6 CA_2A‐5B‐66A 5, 10, 15, 20 5, 10 5, 10 5, 10, 15, 20 5CC #1 2CC #8 CA_2A‐66A (2) 5, 10, 15, 20 5, 10, 15, 20 5CC #1 3CC #7 CA_2A‐4A‐5A 5, 10, 15, 20 5, 10, 15, 20 5, 10 4CC #1 4CC #7 CA_5B‐30A‐66A 5, 10 5, 10 5, 10 5, 10 5CC #1 2CC #9 CA_2A‐71A 5, 10, 15, 20 5, 10, 15, 20 3CC #10 3CC #8 CA_2A‐4A‐12A 5, 10, 15, 20 5, 10, 15, 20 5, 10 No 4CC #8 CA_5B‐66A‐66A 5, 10 5, 10 5, 10, 15, 20 5, 10, 15, 20 5CC #2 2CC #10 CA_4A‐4A 5, 10, 15, 20 5, 10, 15, 20 3CC #6 3CC #9 CA_2A‐4A‐13A 5, 10, 15, 20 5, 10, 15, 20 10 No 4CC #9 CA_5A‐30A‐66A‐66A 5, 10 5, 10 5, 10, 15, 20 5, 10, 15, 20 No 2CC #11 CA_4A‐5A (1) 5, 10, 15, 20 5, 10 4CC #1 3CC #10 CA_2A‐4A‐71A 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 4CC #10 CA_41E 15, 20 15, 20 15, 20 20 No 2CC #12 CA_4A‐12A (4) 5, 10, 15, 20 5, 10 3CC #8 3CC #11 CA_2A‐5B 5, 10, 15, 20 5, 10 5, 10 4CC #5 2CC #13 CA_4A‐13A 5, 10, 15, 20 10 3CC #9 3CC #12 CA_2A‐7A‐12A 5, 10, 15, 20 5, 10, 15, 20 5, 10 No 2CC #14 CA_4A‐17A 5, 10 5, 10 B17 SCC Only No 3CC #13 CA_2A‐12B 5, 10, 15, 20 5 5, 10 No 2CC #15 CA_5B 5, 10 5, 10 5CC #1 3CC #14 CA_2A‐12A‐30A 5, 10, 15, 20 5, 10 5, 10 No 2CC #16 CA_5A‐25A 5, 10 5, 10, 15, 20 No 3CC #15 CA_4A‐4A‐5A 5, 10, 15, 20 5, 10, 15, 20 5, 10 No 2CC #17 CA_7C 15, 20 15, 20 No 3CC #16 CA_5B‐30A 5, 10 5, 10 5, 10 5CC #1 2CC #18 CA_7A‐7A (1) 5, 10, 15, 20 5, 10, 15, 20 No 3CC #17 CA_5B‐66A 5, 10 5, 10 5, 10, 15, 20 5CC #1 2CC #19 CA_7A‐12A 5, 10, 15, 20 5, 10 3CC #12 3CC #18 CA_5A‐30A‐66A 5, 10 5, 10 5, 10, 15, 20 4CC #9 2CC #20 CA_12B 5 5, 10 3CC #13 3CC #19 CA_12A‐66C 5, 10 5, 10, 15, 20 5, 10, 15, 20 No 2CC #21 CA_12A‐25A 5, 10 5, 10, 15, 20 No 3CC #20 CA_30A‐66A‐66A 5, 10 5, 10, 15, 20 5, 10, 15, 20 4CC #9 2CC #22 CA_12A‐30A 5, 10 5, 10 3CC #14 3CC #21 CA_41D 10, 15, 20 10, 15, 20 10, 15, 20 No 2CC #23 CA_41A‐41A (1) 5, 10, 15, 20 5, 10, 15, 20 No 3CC #22 CA_41A‐41C 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 3CC #23 CA_66D 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 3CC #24 CA_66A‐66C 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 No 1.2 LTE Downlink Only Carrier Aggregation Test Selection and Setup SAR test exclusion for LTE downlink Carrier Aggregation is determined by power measurements according to the number component carriers (CCs) supported by the product implementation. For those configurations required by April 2018 TCBC Workshop Notes, conducted power measurements with LTE Carrier Aggregation (CA) (downlink only) active are made in accordance to KDB Publication 941225 D05Av01r02. The RRC connection is only handled by one cell, the primary component carrier (PCC) for downlink and uplink communications. After making a data connection to the PCC, the UE device adds secondary component carrier(s) (SCC) on the downlink only. All uplink communications and acknowledgements remain identical to specifications when downlink carrier aggregation is inactive on the PCC. Additional conducted output powers are measured with the downlink carrier aggregation active for the configuration with highest measured maximum conducted power with downlink carrier aggregation inactive measured among the channel bandwidth, modulation, and RB combinations in each frequency band. Per FCC KDB Publication 941225 D05Av01r02, no SAR measurements are required for carrier aggregation configurations when the maximum average output power with downlink only carrier aggregation active is not more than 0.25 dB higher than the average output power with downlink only carrier aggregation inactive. All bands required for SAR testing per FCC KDB procedures were considered. Based on the measured maximum powers below, no additional SAR tests were required for DLCA SAR configurations. Reviewed by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX H: 04/21/19 - 05/15/19 Portable Handset Page 1 of 3 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

General PCC and SCC configuration selection procedure - PCC uplink channel, channel bandwidth, modulation and RB configurations were selected based on section C)3)b)ii) of KBD 941225 D05 V01r02. The downlink PCC channel was paired with the selected PCC uplink channel according to normal configurations without carrier aggregation. - To maximize aggregated bandwidth, highest channel bandwidth available for that CA combination was selected for SCC. For inter-band CA, the SCC downlink channels were selected near the middle of their transmission bands. For contiguous intra-band CA, the downlink channel spacing between the component carriers was set to multiple of 300 kHz less than the nominal channel spacing defined in section 5.4.1A of 3GPP TS 36.521. For non-contiguous intra-band CA, the downlink channel spacing between the component carriers was set to be larger than the nominal channel spacing and provided maximum separation between the component carriers. - All selected PCC and SCC(s) remained fully within the uplink/downlink transmission band of the respective component carrier. Base Station Wireless Device Simulator Figure 1 DL CA Power Measurement Setup Reviewed by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX H: 04/21/19 - 05/15/19 Portable Handset Page 2 of 3 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019

1.3 Downlink Carrier Aggregation RF Conducted Powers 1.3.1 LTE Band 26 as PCC Table 1 Maximum Output Powers PCC SCC 1 Power LTE Tx.Power LTE Single PCC BW PCC (UL) PCC UL# PCC UL RB PCC (DL) PCC (DL) Freq. SCC BW SCC (DL) SCC (DL) with DL CA Combination PCC Band PCC (UL) Ch. Mod. SCC Band Carrier Tx [MHz] Freq. [MHz] RB Offset Channel [MHz] [MHz] Channel Freq. [MHz] Enabled Power (dBm) (dBm) CA_25A-26A LTE B26 15 26865 831.5 QPSK 1 74 8865 876.5 LTE B25 20 8365 1962.5 25.49 25.42 1.3.2 LTE Band 25 as PCC Table 2 Maximum Output Powers PCC SCC 1 Power LTE Tx.Power LTE Single PCC BW PCC (UL) PCC UL# PCC UL RB PCC (DL) PCC (DL) Freq. SCC BW SCC (DL) SCC (DL) with DL CA Combination PCC Band PCC (UL) Ch. Mod. SCC Band Carrier Tx [MHz] Freq. [MHz] RB Offset Channel [MHz] [MHz] Channel Freq. [MHz] Enabled Power (dBm) (dBm) CA_25A-25A (1) LTE B25 10 26090 1855 QPSK 1 49 8090 1935 LTE B25 20 8590 1985 24.28 24.30 CA_25A-26A LTE B25 10 26090 1855 QPSK 1 49 8090 1935 LTE B26 15 8865 876.5 24.08 24.30 1.3.3 LTE Band 41 PC3 as PCC Table 3 Maximum Output Powers PCC SCC 1 Power LTE Tx.Power LTE Single PCC BW PCC (UL) PCC UL# PCC UL RB PCC (DL) PCC (DL) Freq. SCC BW SCC (DL) SCC (DL) with DL CA Combination PCC Band PCC (UL) Ch. Mod. SCC Band Carrier Tx [MHz] Freq. [MHz] RB Offset Channel [MHz] [MHz] Channel Freq. [MHz] Enabled Power (dBm) (dBm) CA_41A-41A (1) LTE B41 20 40185 2549.5 QPSK 1 0 40185 2549.5 LTE B41 20 41490 2680 24.99 25.00 CA_41C (1) LTE B41 20 40185 2549.5 QPSK 1 0 40185 2549.5 LTE B41 20 40383 2569.3 24.99 25.00 1.3.1 LTE Band 41 PC2 as PCC Table 4 Maximum Output Powers PCC SCC 1 Power LTE Tx.Power LTE Single PCC BW PCC (UL) PCC UL# PCC UL RB PCC (DL) PCC (DL) Freq. SCC BW SCC (DL) SCC (DL) with DL CA Combination PCC Band PCC (UL) Ch. Mod. SCC Band Carrier Tx [MHz] Freq. [MHz] RB Offset Channel [MHz] [MHz] Channel Freq. [MHz] Enabled Power (dBm) (dBm) CA_41A-41A (1) LTE B41 PC2 15 41055 2636.5 QPSK 1 74 41055 2636.5 LTE B41 PC2 20 39750 2506 27.68 27.68 CA_41C (1) LTE B41 PC2 15 41055 2636.5 QPSK 1 74 41055 2636.5 LTE B41 PC2 20 40884 2619.4 27.69 27.68 Reviewed by: FCC ID: ZNFQ720PS SAR EVALUATION REPORT Quality Manager Test Dates: DUT Type: APPENDIX H: 04/21/19 - 05/15/19 Portable Handset Page 3 of 3 © 2019 PCTEST Engineering Laboratory, Inc. REV 21.3 M 02/15/2019


Document Created: 2019-05-31 07:34:37
Document Modified: 2019-05-31 07:34:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC