DFS Test Report

FCC ID: ZNFP768G

Test Report

Download: PDF
FCCID_1800476

FCC DFS Test Report Report No. : FZ272001 FCC DFS Test Report Equipment : Cellular/PCS GSM/GPRS/EDGE and Cellular/PCS WCDMA/HSPA Phone with Bluetooth and WLAN Model No. : LG-P768G, LGP768g, LGP768G, P769g, P769G Standard : 47 CFR FCC Part 15.407 Applicant : LG Electronics MobileComm U.S.A., Inc. Manufacturer 1000 Sylvan Avenue, Englewood Cliffs NJ 07632 DFS Operate Mode : Client without radar detection The product sample received on Jul. 31, 2012 and completely tested on Aug. 01, 2012. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in FCC 06-96 Appendix and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Wayne Hsu Tested by: XXXX / Engineer SPORTON INTERNATIONAL INC. Page No. : 1 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 Table of Contents 1 GENERAL DESCRIPTION ...............................................................................................................5 1.1 Information........................................................................................................................................5 1.2 Support Equipment ...........................................................................................................................7 1.3 Testing Applied Standards ................................................................................................................ 7 1.4 Testing Location Information .............................................................................................................7 1.5 Measurement Uncertainty .................................................................................................................7 2 TEST CONFIGURATION OF EUT ....................................................................................................8 2.1 DFS and TPC Information .................................................................................................................8 2.2 The Worst Case Measurement Configuration .................................................................................... 8 3 DYNAMIC FREQUENCY SELECTION (DFS) TEST RESULT .......................................................... 9 3.1 General DFS Information .................................................................................................................. 9 3.2 Radar Test Waveform Calibration.................................................................................................... 11 3.3 In-service Monitoring ....................................................................................................................... 16 4 TEST EQUIPMENT AND CALIBRATION DATA............................................................................. 18 5 CERTIFICATION OF TAF ACCREDITATION ................................................................................. 19 SPORTON INTERNATIONAL INC. Page No. : 2 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 Summary of Test Result Conformance Test Specifications (FCC 06-96 Appendix) Report Ref. Std. Description Measured Limit Result Clause Clause - 7.8.1 DFS: UNII Detection N/A (Client w/o test) 80% of the 99% N/A Bandwidth Measurement BW - 7.8.2.1 DFS: Initial Channel N/A (Client w/o test) CAC 60 sec N/A Availability Check Time - 7.8.2.2 DFS: Radar Burst at the N/A (Client w/o test) Detection N/A Beginning of the Channel Threshold: Availability Check Time -64 dBm - 7.8.2.3 DFS: Radar Burst at the N/A (Client w/o test) Detection N/A End of the Channel Threshold: Availability Check Time -64 dBm 3.3 7.8.3 DFS: In-Service Monitoring CMT < 10sec CMT 10sec Complied for Channel Move Time (CMT) 3.3 7.8.3 DFS: In-Service Monitoring CCTT < 60 ms CCTT 60 ms Complied for Channel Closing starting at CMT Transmission Time (CCTT) 200ms 3.3 7.8.3 DFS: In-Service Monitoring NOP > 30 min NOP 30 min Complied for Non-Occupancy Period (NOP) - 7.8.4 DFS: Statistical N/A (Client w/o test) Table 5 - 7 N/A Performance Check (KDB 905462) - 5.8.1 DFS: Uniform Spreading N/A (Client w/o this Uniform N/A function) Spreading for DFS Band 3.1.4 8.1 User Access Restrictions Manufacturer attestation DFS controls Complied NOT accessible to user SPORTON INTERNATIONAL INC. Page No. : 3 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 Revision History Report No. Version Description Issued Date FZ272001 Rev. 01 Initial issue of report Aug. 17, 2012 SPORTON INTERNATIONAL INC. Page No. : 4 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 1 General Description 1.1 Information 1.1.1 RF General Information RF General Information IEEE Std. Frequency 802.11 Ch. Frequency (MHz) Channel Number Range (MHz) Protocol 5250-5350 a 5260-5320 52-64 [4] 5470-5725 5500-5700 100-140 [7] 5250-5350 n (HT20) 5260-5320 52-64 [4] 5470-5725 5500-5700 100-140 [7] Note 1: IEEE Std. 802.11-2007 modulation consists of IEEE Std. 802.11a-1999. Note 2: IEEE Std. 802.11n-2009 modulation consists of HT20 (HT: High Throughput). Then EUT support HT20. Transmitter Chains & Receiver Chains Information Number of Correlation IEEE Std. 802.11 Number of Receive Channel Transmit Chains Signals with Protocol Chains (NRX) Bandwidth (MHz) (NTX) Multiple NTX a 1 1 N/A 20 n (HT20) 1 1 Uncorrelated 20 SPORTON INTERNATIONAL INC. Page No. : 5 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 1.1.2 Antenna Information Antenna Category Equipment placed on the market without antennas Integral antenna (antenna permanently attached) Temporary RF connector provided No temporary RF connector provided Transmit chains bypass antenna and soldered temporary RF connector provided for connected measurement. In case of conducted measurements the transmitter shall be connected to the measuring equipment via a suitable attenuator and correct for all losses in the RF path. External antenna (dedicated antennas) Single power level with corresponding antenna(s). Power Level (PL): 1 Multiple power level and corresponding antenna(s). Power Level (PL): 1~… Antenna General Information Antenna Port (Total 1 Port) 1(TX/RX) Ant. Port DG (dBi) DG (dBi) Ant. [Ant No. X Ant. PL Ant. Type Model GANT (dBi) [correlated] [uncorrelated] No. connect to Cat. NTX = 1 NTX = 1 Ant. Port Y] 1 1 1 Integral FPCB LG-P768g -0.63 N/A N/A For radiated tests, the DFS test should be performed with lowest antenna gain (regardless of antenna type). Then Ant. No. 1 shall be performed the radiated DFS test. SPORTON INTERNATIONAL INC. Page No. : 6 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 1.2 Support Equipment Support Equipment No. Equipment Brand Name Model Name FCC ID 1 Notebook PC ASUS Eee PC 904HD MSQEPC9HD780 2 Access Point 3Com WL-605 O9C-WL605 1.3 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: FCC 06-96 Appendix FCC KDB 905462 5 GHz UNII DFS Compliance Procedures FCC KDB 443999 Approval of DFS UNII Devices 1.4 Testing Location Information Testing Location HWA YA ADD : No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL : 886-3-327-3456 FAX : 886-3-318-0055 JHUBEI ADD : No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL : 886-3-656-9065 FAX : 886-3-656-9085 Test Condition Test Site No. Test Engineer Test Environment Test Date DFS Site DF01-HY Bear Chen 24.8°C / 62% 01-Aug-12 1.5 Measurement Uncertainty ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Test Item Uncertainty Limit -7 Radio frequency ± 8.7 X 10 N/A RF output power, conducted ±0.63 dB N/A All emissions, conducted ±0.83 dB N/A All emissions, radiated ±2.87 dB N/A Temperature ±0.8 °C N/A Humidity ±3 % N/A DC and low frequency voltages ±3 % N/A Time ±1.42 % N/A SPORTON INTERNATIONAL INC. Page No. : 7 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 2 Test Configuration of EUT 2.1 DFS and TPC Information The DFS Related Operating Mode(s) of the Equipment Master Client with radar detection Client without radar detection DFS Software / Firmware Ver. LGP768g-V06c H/W Ver.; S/W Ver. HW Version : Rev.A; SW Version : V06c Communication Mode IP Based (Load Based) Frame Based IEEE Std. Frequency TPC (Transmit 802.11 Ad-hoc Hotspot Passive Scan Range (MHz) Power Control) Protocol a 5250-5350 No No No Yes n (HT20) 5470-5600 No No No Yes 5600-5650 N/A N/A N/A N/A 5650-5725 No No No Yes 2.2 The Worst Case Measurement Configuration The Worst Case Mode for Following Conformance Tests Tests Item Dynamic Frequency Selection (DFS) Test Condition Radiated measurement (Vertical Polarization) Worst Modulation Number of Transmit Chains (NTX) Number of Receive Chains (NRX) Mode 11N5.3G-20M 1 1 SPORTON INTERNATIONAL INC. Page No. : 8 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3 Dynamic Frequency Selection (DFS) Test Result 3.1 General DFS Information 3.1.1 DFS Parameters Table D.1: DFS requirement values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1. Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second periods. See Notes 1 and 2. U-NII Detection Bandwidth Minimum 80% of the 99% power bandwidth See Note 3. Note 1: The instant that the Channel Move Time and the Channel Closing Transmission Time begins is as follows: • For the Short pulse radar Test Signals this instant is the end of the Burst. • For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst generated. • For the Long Pulse radar Test Signal this instant is the end of the 12 second period defining the radar transmission. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate Channel changes (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 1 is used and for each frequency step the minimum percentage of detection is 90%. Measurements are performed with no data traffic. Table D.2: Interference threshold values Maximum Transmit Power Value (see note) 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. SPORTON INTERNATIONAL INC. Page No. : 9 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.1.2 Applicability of DFS Requirements Prior to Use of a Channel DFS Operational mode Requirement Client without radar Client with radar Master detection detection Non-Occupancy Period Yes Not required Yes DFS Detection Threshold Yes Not required Yes Channel Availability Check Time Yes Not required Not required Uniform Spreading Yes Not required Not required U-NII Detection Bandwidth Yes Not required Yes 3.1.3 Applicability of DFS Requirements during Normal Operation DFS Operational mode Requirement Client without radar Client with radar Master detection detection DFS Detection Threshold Yes Not required Yes Channel Closing Transmission Time Yes Yes Yes Channel Move Time Yes Yes Yes U-NII Detection Bandwidth Yes Not required Yes 3.1.4 User Access Restrictions User Access Restrictions DFS controls (hardware or software) related to radar detection are NOT accessible to the user. Manufacturer statement confirming that information regarding the parameters of the detected Radar Waveforms is not available to the end user. 3.1.5 Channel Loading/Data Streaming IP Based (Load Based) - stream the test file from the Master to the Client. Performed NTIA approved WAV file. (EUT w/o video function application) Performed NTIA approved MPEG2 file. (EUT with video function application) Alternative streaming e.g., FTP with about 17 to 20% loading and submit proposal to FCC. Frame Based - stream the test file from the Master to the Client. fixed talk/listen ratio, set the ratio to 45%/55% SPORTON INTERNATIONAL INC. Page No. : 10 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.2 Radar Test Waveform Calibration 3.2.1 Short Pulse Radar Test Waveforms Minimum Radar Pulse Width Number of Percentage of PRI (µsec) Minimum Trials Type (µsec) Pulses Successful Detection 1 1 1428 18 60% 30 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 A minimum of 30 unique waveforms are required for each of the short pulse radar types 2 through 4. For short pulse radar type 1, the same waveform is used a minimum of 30 times. If more than 30 waveforms are used for short pulse radar types 2 through 4, then each additional waveform must also be unique and not repeated from the previous waveforms. The aggregate is the average of the percentage of successful detections of short pulse radar types 1-4. 3.2.2 Long Pulse Radar Test Waveform Minimum Pulse Chirp Number of Radar Number of Percentage of Minimum Width Width PRI (µsec) Pulses Type Bursts Successful Trials (µsec) (MHz) per Burst Detection 5 50-100 5-20 1000-2000 1-3 8-20 80% 30 Each waveform is defined as follows: The transmission period for the Long Pulse Radar test signal is 12 seconds. There are a total of 8 to 20 Bursts in the 12 second period, with the number of Bursts being randomly chosen. This number is Burst_Count. Each Burst consists of 1 to 3 pulses, with the number of pulses being randomly chosen. Each Burst within the 12 second sequence may have a different number of pulses. The pulse width is between 50 and 100 microseconds, with the pulse width being randomly chosen. Each pulse within a Burst will have the same pulse width. Pulses in different Bursts may have different pulse widths. Each pulse has a linear FM chirp between 5 and 20 MHz, with the chirp width being randomly chosen. Each pulse within a Burst will have the same chirp width. Pulses in different Bursts may have different chirp widths. The chirp is centered on the pulse. For example, with a radar frequency of 5300 MHz and a 20 MHz chirped signal, the chirp starts at 5290 MHz and ends at 5310 MHz. If more than one pulse is present in a Burst, the time between the pulses will be between 1000 and 2000 microseconds, with the time being randomly chosen. If three pulses are present in a Burst, the time between the first and second pulses is chosen independently of the time between the second and third pulses. The 12 second transmission period is divided into even intervals. The number of intervals is equal to Burst_Count. Each interval is of length (12,000,000 / Burst_Count) microseconds. Each interval contains one Burst. The start time for the Burst, relative to the beginning of the interval, is between 1 and [(12,000,000 / Burst_Count) – (Total Burst Length) + (One Random PRI Interval)] microseconds, with the start time being randomly chosen. The step interval for the start time is 1 microsecond. The start time for each Burst is chosen independently. SPORTON INTERNATIONAL INC. Page No. : 11 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.2.3 Frequency Hopping Radar Test Waveform Minimum Pulse Hopping Radar PRI Pulses Hopping Percentage of Minimum Width Sequence Type (µsec) per Hop Rate (kHz) Successful Trials (µsec) Length (ms) Detection 6 1 333 9 0.333 300 70% 30 The FCC Type 6 waveform uses a static waveform with 100 bursts in the instruments ARB. In addition, the RF list mode is operated with a list containing 100 frequencies from a randomly generated list and it had be ensured that at least one of the random frequencies falls into the UNII Detection Bandwidth of the DUT. Each burst from the waveform file initiates a trigger pulse at the beginning that switches the RF list from one item to the next one. 3.2.4 Master DFS Threshold Level Master DFS Threshold Level DFS Threshold level: -63 dBm at the antenna connector in front of the antenna The Interference Radar Detection Threshold Level is (-64dBm) + {1 dB} = -63 dBm. That had been taken into account the master output power range and antenna gain. SPORTON INTERNATIONAL INC. Page No. : 12 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.2.5 Calibration Setup Radiated Calibration Setup Calibration Plots Radar #1 DFS detection threshold level MARKER 1 RBW 1 MHz Marker 1 [T1 ] 1.38 ms * VBW 1 MHz -63.31 dBm Ref -15 dBm * Att 0 dB SWT 30 ms 1.380000 ms Offset -4 dB -20 A 1 AP -30 CLRWR TRG LVL -40 -50 -601 -70 TRG -70 dBm -80 -90 -100 -110 Center 5.5 GHz 3 ms/ Date: 1.AUG.2012 15:37:14 SPORTON INTERNATIONAL INC. Page No. : 13 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.2.6 Test Setup A spectrum analyzer is used as a monitor to verify that the EUT has vacated the Channel within the (Channel Closing Transmission Time and Channel Move Time, and does not transmit on a Channel during the Non-Occupancy Period after the detection and Channel move. Slave without Radar Detect Radiated Measurement SPORTON INTERNATIONAL INC. Page No. : 14 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 Verification that when the EUT is “off” that the RF energy emitted Plots Without Data Traffic Plot (Noise Plot) EUT Data Traffic Plot MARKER 1 RBW 1 MHz Marker 1 [T1 ] MARKER 1 RBW 1 MHz Marker 1 [T1 ] 10.6035 s * VBW 1 MHz -81.42 dBm 3.516 s * VBW 1 MHz -33.26 dBm Ref -15 dBm * Att 0 dB SWT 12 s 10.603500 s Ref -15 dBm * Att 0 dB SWT 12 s 3.516000 s Offset -4 dB Offset -4 dB -20 -20 A A SGL SGL 1 AP -30 1 AP -30 1 CLRWR CLRWR LVL LVL -40 -40 -50 -50 -60 -60 -70 -70 1 -80 -80 -90 -90 -100 -100 -110 -110 Center 5.5 GHz 1.2 s/ Center 5.5 GHz 1.2 s/ Date: 1.AUG.2012 15:46:18 Date: 1.AUG.2012 16:04:34 Master Data Traffic Plot MARKER 1 RBW 1 MHz Marker 1 [T1 ] 4.35 s * VBW 1 MHz -63.00 dBm Ref -15 dBm * Att 0 dB SWT 12 s 4.350000 s Offset -4 dB -20 A SGL 1 AP -30 CLRWR LVL -40 -50 -60 1 -70 -80 -90 -100 -110 Center 5.5 GHz 1.2 s/ Date: 1.AUG.2012 16:03:12 SPORTON INTERNATIONAL INC. Page No. : 15 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.3 In-service Monitoring 3.3.1 In-service Monitoring Limit In-service Monitoring Limit Channel Move Time 10 sec Channel Closing Transmission Time 200 ms + an aggregate of 60 ms over remaining 10 sec periods. Non-occupancy period Minimum 30 minutes 3.3.2 Measuring Instruments Refer a test equipment and calibration data table in this test report. 3.3.3 Test Procedures Test Method Refer as FCC 06-96 Appendix, clause 7.8.3 verified during In-Service Monitoring; Channel Closing Transmission Time, Channel Move Time. Client Device will associate with the EUT. Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. Measure and record the transmissions from the EUT during the observation time (Channel Move Time). Compare the Channel Move Time and Channel Closing Transmission Time limits. Refer as FCC 06-96 Appendix, clause 8.3 verified during In-Service Monitoring; Channel Closing Transmission Time, Channel Move Time. One 10 sec plot needs to be reported for the Short Pulse Radar Types 1-4 and one for the Long Pulse Radar Type in a 22 sec plot. And zoom-in a 600 ms plot verified channel closing time for the aggregate transmission time starting from 200ms after the end of the radar signal to the completion of the channel move. Refer as FCC 06-96 Appendix, clause 7.8.3 verified during In-Service Monitoring; Non-Occupancy Period. Client Device will associate with the EUT. Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. Measure and record the transmissions from the EUT during the observation time (Non-Occupancy Period). Compare the Non-Occupancy Period limits. SPORTON INTERNATIONAL INC. Page No. : 16 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 3.3.4 Test Result of In-service Monitoring Channel Closing Transmission Time and Channel Move Time Result Channel Closing Modulation Radar Type Channel Move Time Freq. (MHz) Transmission Time Mode Signal Measured Limit Measured Limit 1N5.6G-20M 5500 1 0 ms 60 ms 0 ms 10 s Result Complied 12 sec Timing Plot Zoom-in 600 ms Timing Plot TIME LINE 1 RBW 1 MHz Marker 2 [T1 ] CENTER FREQUENCY RBW 1 MHz Delta 1 [T1 ] 665.7 ms * VBW 1 MHz -84.31 dBm 5.5 GHz * VBW 1 MHz -6.01 dB Ref -15 dBm * Att 0 dB SWT 12 s 10.465700 s Ref -15 dBm * Att 0 dB SWT 600 ms 200.000000 ms Offset -4 dB Marker 1 [T1 ] Offset -4 dB Marker 1 [T1 ] -20 -38.01 dBm -20 -80.21 dBm 465.700000 ms A A 0.000000 s Delta 1 [T1 ] SGL SGL 1 AP -30 1 AP -30 CLRWR -46.24 dB 1 CLRWR TRG 858.800000 ms LVL LVL -40 -40 -50 Master -50 -60 -60 -70 -70 1 -80 1 2 -80 1 -90 -90 -100 -100 T2 -110 T1 -110 T1 Center 5.5 GHz 1.2 s/ Center 5.5 GHz 60 ms/ Date: 1.AUG.2012 16:17:54 Date: 1.AUG.2012 16:36:12 Non-Occupancy Period Result Modulation Non-Occupancy Period Freq. (MHz) Mode Measured Limit Result 11N5.6G-20M 5500 >30min 30 min Complied 2000 sec Timing Plot TIME LINE 2 RBW 1 MHz Marker 2 [T1 ] 1831.3 s * VBW 1 MHz -81.85 dBm Ref -15 dBm * Att 0 dB SWT 2000 s 1.831300 ks Offset -4 dB Marker 1 [T1 ] -20 -34.38 dBm A 31.300000 s Delta 1 [T1 ] SGL 1 AP -30 1 -48.29 dB CLRWR 10.000000 s LVL -40 -50 -60 -70 1 -80 2 -90 -100 T2 -110 T1 Center 5.5 GHz 200 s/ Date: 1.AUG.2012 18:32:23 SPORTON INTERNATIONAL INC. Page No. : 17 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 4 Test Equipment and Calibration Data Instrument Manufacturer Model No. Serial No. Spec. Calibration Date Remark Spectrum R&S FSP 7 100643 9kHz ~ 7GHz Aug. 23, 2011 DFS01-HY Analyzer Vector Signal R&S SMU200A 102098 100kHz ~ 6GHz Oct. 05, 2011 DFS01-HY Generator HUBER+SUHNE RF Cable-3m SUCOFLEX_104 302338 1GHz ~ 26.5GHz Jan. 01, 2012 DFS01-HY R HUBER+SUHNE RF Cable-10m SUCOFLEX_104 302345 1GHz ~ 26.5GHz Jan. 01, 2012 DFS01-HY R Horn Antenna COM-POWER AH-118 10091 1GHz ~ 18GHz Feb. 15, 2012 DFS01-HY SPORTON INTERNATIONAL INC. Page No. : 18 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973

FCC DFS Test Report Report No. : FZ272001 5 Certification of TAF Accreditation SPORTON INTERNATIONAL INC. Page No. : 19 of 19 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973


Document Created: 2019-06-07 11:57:50
Document Modified: 2019-06-07 11:57:50
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC