Part 90 Test Report

FCC ID: ZNFLS980

Test Report

Download: PDF
FCCID_2048827

PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 90 CDMA / LTE Applicant: Date of Testing: LG Electronics MobileComm U.S.A Aug. 1-5, 2013 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab., Columbia, MD, USA United States Test Report Serial No.: 0Y1307031177.ZNF FCC I D: ZNFLS980 APPLI C A NT: LG ELECTRONICS MOBILECOMM U.S.A Applicant Type: Class II Permissive Change FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part: §90.691 EUT Type: Portable Handset Model(s): LS-980, LGLS980 Test Device Serial No.: identical prototype [S/N: LTE/CDMA] Class II Permissive Change: Please see FCC change documents. Original Grant Date: 7/23/2013 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

T A B L E O F C O N T E N T S FCC PART 90 MEASUREMENT REPORT………………………………..…………….………………..………3 1.0 INTRODUCTION ..............................................................................................................................4 1.1 SCOPE ................................................................................................................................................ 4 1.2 TESTING FACILITY............................................................................................................................. 4 2.0 PRODUCT INFORMATION..............................................................................................................5 2.1 EQUIPMENT DESCRIPTION .............................................................................................................. 5 2.2 DEVICE CAPABILITIES....................................................................................................................... 5 2.3 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ........................................................................... 5 3.0 DESCRIPTION OF TESTS ..............................................................................................................6 3.1 EVALUATION PROCEDURE .............................................................................................................. 6 3.2 RADIATED POWER AND RADIATED SPURIOUS EMISSIONS ........................................................ 6 4.0 TEST EQUIPMENT CALIBRATION DATA ......................................................................................7 5.0 SAMPLE CALCULATIONS ..............................................................................................................8 6.0 TEST RESULTS...............................................................................................................................9 6.1 SUMMARY........................................................................................................................................... 9 6.2 BC10 CDMA RADIATED MEASUREMENTS .................................................................................... 10 6.3 BAND 26 LTE RADIATED MEASUREMENTS .................................................................................. 12 7.0 CONCLUSION................................................................................................................................14 Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

MEASUREMENT REPORT FCC Part 90 CDMA / LTE §2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland Mills Road, Columbia, MD 21045 USA BASE MODEL: LS-980 FCC CLASSIFICATION: PCS Licensed Transmitter Held to Ear (PCE) MODE: CDMA / EvDO / LTE FREQUENCY TOLERANCE: ±0.00025 % (2.5 ppm) Test Device Serial No.: LTE/CDMA Production Pre-Production Engineering DATE(S) OF TEST: Aug. 1-5, 2013 TEST REPORT S/N: 0Y1307031177.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab. located in Columbia, MD 21045, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 90864) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451A-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451A-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 Testing Facility The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility in New Concept Business Park, Guilford Industrial Park, Columbia, Maryland. The site address is 6660-B Dobbin Road, Columbia, MD 21045. The test site is one of the highest points in the Columbia area with an elevation of 390 feet above mean sea level. The site coordinates are 39o 11’15” N latitude and 76o 49’38” W longitude. The facility is 1.5 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. There are no FM or TV transmitters within 15 miles of the site. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2003/2009 on January 10, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFLS980. The EUT consisted of the following component(s): Trade Name / Base Model FCC ID Description LG / Model: LS-980 ZNFLS980 Portable Handset Table 2-1. EUT Equipment Description Note: All data contained in this report is applicable for the device operation in the 814.7 – 824 MHz frequency range (In addition, data in this report is both from the CDMA and LTE transmitter in the respective band). Test data shown supports the devices compliance with §90.691 of the FCC Rules and Regulation. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A (BC0, BC1, BC10), 850/1900 GSM/GPRS/EDGE, 850/1900 WCDMA/HSPA, Band 25 (3,5,10MHz), 26 (1.4,3,5,10 MHz), 41 (10,15,20 MHz) LTE, 802.11a/b/g/n/ac WLAN (DTS/NII), Bluetooth (1x,EDR, LE), NFC 2.3 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the “Land Mobile FM or PM – Communications Equipment Measurements and Performance Standards” (ANSI/TIA-603-C-2004) was used in the measurement of the measurement of the LG Portable Handset FCC ID: ZNFLS980. 3.2 Radiated Power and Radiated Spurious Emissions §2.1053, §90.635, §90.691 The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An ETS Lindgren Model 2188 raised turntable is used for radiated measurement. It is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. A 78cm high PVC support structure is placed on top of the turntable. A ¾” (~1.9cm) sheet of high density polyethylene is used as the table top and is placed on top of the PVC supports to bring the total height of the table to 80cm. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Radiated power levels are also investigated with the receive antenna horizontally and vertically polarized. The maximized power level is recorded using the spectrum analyzer “Channel Power” function with the integration band set to the emissions’ occupied bandwidth, a RMS detector, RBW = 100kHz, VBW = 300kHz, and a 1 second sweep time over a minimum of 10 sweeps, per the guidelines of KDB 971168. Per the guidance of ANSI/TIA-603-C-2004, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]) specified in 90.691. For fundamental radiated power measurements, the guidance of KDB 971168 is used to record the EUT power level that is subsequently matched via the aforementioned substitution method given in ANSI/TIA- 603-C-2004. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

4.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number - RE1 Radiated Emissions Cable Set (UHF/EHF) 3/29/2013 Annual 3/29/2014 N/A - RE2 Radiated Emissions Cable Set (VHF/UHF) 3/29/2013 Annual 3/29/2014 N/A - LTx2 Licensed Transmitter Cable Set 1/17/2013 Annual 1/17/2014 N/A Agilent 8449B (1-26.5GHz) Pre-Amplifier 4/17/2013 Annual 4/17/2014 3008A00985 Agilent 8648D (9kHz-4GHz) Signal Generator 10/10/2012 Annual 10/10/2013 3613A00315 Agilent N9020A MXA Signal Analyzer 10/9/2012 Annual 10/9/2013 US46470561 Agilent N9038A MXE EMI Receiver 12/8/2012 Annual 12/8/2013 MY51210133 Anritsu MA2411B Pulse Sensor 9/19/2012 Annual 9/19/2013 1027293 Anritsu ML2495A Power Meter 10/11/2012 Annual 10/11/2013 1039008 Mini-Circuits VHF-1300+ High Pass Filter 1/21/2013 Annual 1/21/2014 30716 Mini-Circuits VHF-3100+ High Pass Filter 1/21/2013 Annual 1/21/2014 31144 Rohde & Schwarz CMU200 Base Station Simulator N/A N/A 836536/0005 Schwarzbeck UHA 9105 Dipole Antenna (400 - 1GHz) Tx 10/3/2011 Biennial 10/3/2013 91052522TX Schwarzbeck UHA 9105 Dipole Antenna (400 - 1GHz) Rx 10/3/2011 Biennial 10/3/2013 91052523RX Seekonk NC-100 Torque Wrench (8" lb) 3/5/2012 Triennial 3/5/2015 N/A Sunol DRH-118 Horn Antenna (1 - 18GHz) 6/19/2013 Biennial 6/19/2015 A050307 Sunol DRH-118 Horn Antenna (1-18 GHz) 6/19/2013 Biennial 6/19/2015 A042511 Table 4-1. Test Equipment Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

5.0 SAMPLE CALCULATIONS Spurious Radiated Emission – BC10 Example: Channel 476 CDMA BC10 Mode 3rd Harmonic (2453.70MHz) The average spectrum analzyer reading at 3 meters with the EUT on the turntable was –81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of –81.0 dBm on the spectrum analzyer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 2453.70 MHz. So 6.1 dB is added to the signal generator reading of –30.9 dBm yielding –24.80 dBm. The fundamental EIRP was 25.501 dBm so this harmonic was 25.501 dBm – (-24.80) = 50.3 dBc. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

6.0 TEST RESULTS 6.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFLS980 FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): LTE / CDMA / EvDO FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result §2.1053, < 43 + 10log10 (P[Watts]) for all Sections Undesirable Emissions CONDUCTED PASS §90.691 out-of-band emissions 6.2, 6.3 Table 6-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. 2) Band Class 10 - CDMA High Channel for this device is Channel 670. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

6.2 BC10 CDMA Radiated Measurements §2.1053, §90.691 Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 817.90 MHz CHANNEL: 476 MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = -13.00 dBm LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN Margin (dB) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1635.80 -43.31 8.58 -34.73 H -21.73 2453.70 -58.58 8.78 -49.79 H -36.79 3271.60 -120.95 9.08 -111.87 H -98.87 4089.50 -118.85 9.58 -109.26 H -96.26 4907.40 -119.43 11.28 -108.15 H -95.15 Table 6-2. Radiated Spurious Data (Ch. 476) NOTES: 1. This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case test configuration was found in the horizontal setup. The data reported in the table above was measured in this test setup. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

BC10 CDMA Radiated Measurements (Cont’d) §2.1053, §90.691 Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 822.75 MHz CHANNEL: 670 MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = -13.00 dBm LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN Margin (dB) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1645.50 -44.72 8.51 -36.21 H -23.21 2468.25 -59.36 8.75 -50.61 H -37.61 3291.00 -120.91 9.11 -111.80 H -98.80 4113.75 -119.04 9.71 -109.33 H -96.33 4936.50 -119.24 11.24 -108.00 H -95.00 Table 6-3. Radiated Spurious Data (Ch. 670) NOTES: 1. This device was tested under all R.C.s and S.O.s and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case test configuration was found in the horizontal setup. The data reported in the table above was measured in this test setup. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

6.3 Band 26 LTE Radiated Measurements §2.1053, §90.691 Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 814.70 MHz CHANNEL: 26697 MEASURED OUTPUT POWER: 24.01 dBm = 0.252 W MODULATION SIGNAL: QPSK DISTANCE: 3 meters LIMIT: 43 + 10 log 10 (W) = -13.00 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN Margin (dB) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1629.40 -41.00 8.58 -32.43 H -19.43 2444.10 -58.46 8.78 -49.68 H -36.68 3258.80 -49.42 9.08 -40.34 H -27.34 4073.50 -118.85 9.58 -109.26 H -96.26 4888.20 -119.43 11.28 -108.15 H -95.15 Table 6-4. Radiated Spurious Data NOTES: 1. This device was tested under all modulations, RB sizes and offsets, and channel bandwidth configurations and the worst case emissions are reported with 1/0. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case test configuration was found in the horizontal setup. The data reported in the table above was measured in this test setup. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

Band 26 LTE Radiated Measurements (Cont’d) §2.1053, §90.691 Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 823.30 MHz CHANNEL: 26783 MEASURED OUTPUT POWER: 24.20 dBm = 0.263 W MODULATION SIGNAL: QPSK DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = -13.00 dBc LEVEL @ SPURIOUS SUBSTITUTE FREQUENCY ANTENNA EMISSION POL ANTENNA GAIN Margin (dB) (MHz) TERMINALS LEVEL (H/V) (dBd) (dBm) (dBm) 1646.60 -43.04 8.51 -34.53 H -21.53 2469.90 -58.77 8.75 -50.01 H -37.01 3293.20 -49.26 9.11 -40.15 H -27.15 4116.50 -119.04 9.71 -109.33 H -96.33 4939.80 -119.24 11.24 -108.00 H -95.00 Table 6-5. Radiated Spurious Data NOTES: 1. This device was tested under all modulations, RB sizes and offsets, and channel bandwidth configurations and the worst case emissions are reported with 1/0. 2. This unit was tested with its standard battery. 3. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case test configuration was found in the horizontal setup. The data reported in the table above was measured in this test setup. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010

7.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFLS980 complies with all the requirements of Parts 90 of the FCC rules. Part 90 CDMA / EvDO / LTE MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS980 (Class II Permissive Change) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 14 0Y1307031177.ZNF Aug. 1-5, 2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 1.3CFI 10/26/2010


Document Created: 2013-08-20 13:29:01
Document Modified: 2013-08-20 13:29:01
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC