Pt 22-24 Test Report

FCC ID: ZNFLS885

Test Report

Download: PDF
FCCID_2324697

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 22 & 24 Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 6/9-6/20/2014 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab., Columbia, MD, USA United States Test Report Serial No.: 0Y1406091173.ZNF FCC I D: ZNFLS885 AP P LI C ANT: LG ELECTRONICS MOBILECOMM U.S. A Application Type: Class II Permissive Change Model(s): LS885, LG-LS885, LS885 EUT Type: Portable Handset FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part(s): §2 §22(H) §24(E) Test Procedure(s): ANSI/TIA-603-C-2004, KDB 971168 v02r01 Test Device Serial No.: identical prototype [S/N: 9JUNE-7] Class II Permissive Change: Please see FCC change document Original Grant Date: 6/9/2014 ERP/EIRP Tx Frequency Max. Max. Mode (MHz) Power Power (W) (dBm) CDMA850 824.70 - 848.31 0.073 18.61 CDMA1900 1851.25 - 1908.75 0.072 18.57 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

T A B L E O F C O N T E N T S FCC PART 22 & 24 MEASUREMENT REPORT .......................................................................................... 3 1.0 INTRODUCTION .............................................................................................................................. 4 1.1 SCOPE ................................................................................................................................................ 4 1.2 TESTING FACILITY ............................................................................................................................. 4 2.0 PRODUCT INFORMATION .............................................................................................................. 5 2.1 EQUIPMENT DESCRIPTION .............................................................................................................. 5 2.2 DEVICE CAPABILITIES....................................................................................................................... 5 2.3 TEST CONFIGURATION ..................................................................................................................... 5 2.4 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ........................................................................... 5 3.0 DESCRIPTION OF TESTS .............................................................................................................. 6 3.1 EVALUATION PROCEDURE .............................................................................................................. 6 3.2 CELLULAR - BASE FREQUENCY BLOCKS ....................................................................................... 6 3.3 CELLULAR - MOBILE FREQUENCY BLOCKS ................................................................................... 6 3.4 PCS - BASE FREQUENCY BLOCKS .................................................................................................. 6 3.5 PCS - MOBILE FREQUENCY BLOCKS .............................................................................................. 7 3.6 RADIATED MEASUREMENTS ............................................................................................................ 7 4.0 TEST EQUIPMENT CALIBRATION DATA ...................................................................................... 8 5.0 SAMPLE CALCULATIONS .............................................................................................................. 9 6.0 TEST RESULTS ............................................................................................................................. 10 6.1 SUMMARY......................................................................................................................................... 10 6.2 RADIATED POWER (ERP/EIRP) ...................................................................................................... 11 6.3 RADIATED SPURIOUS EMISSIONS MEASUREMENTS ................................................................. 13 7.0 CONCLUSION ................................................................................................................................ 18 FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

MEASUREMENT REPORT FCC Part 22 & 24 §2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland Mills Road, Columbia, MD 21046 USA FCC RULE PART(S): §2 §22(H) §24(E) BASE MODEL: LS885 FCC ID: ZNFLS885 FCC CLASSIFICATION: PCS Licensed Transmitter Held to Ear (PCE) MODE: CDMA FREQUENCY TOLERANCE: ±0.00025 % (2.5 ppm) Test Device Serial No.: 9JUNE-7 Production Pre-Production Engineering DATE(S) OF TEST: 6/9-6/20/2014 TEST REPORT S/N: 0Y1406091173.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451B-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 Testing Facility The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at o o 7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39 10’23” N latitude and 76 49’50” W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on February 15, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFLS885. The test data contained in this report pertains only to the emissions due to the EUT’s 2G/3G licensed transmitters. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA (BC0, BC1, BC10), Multi-band LTE, 802.11a/b/g/n WLAN, 802.11a/n UNII, Bluetooth (1x, EDR, LE) 2.3 Test Configuration The LG Portable Handset FCC ID: ZNFLS885 was tested per the guidance of ANSI/TIA-603-C-2004 and KDB 971168 v02r01. See Section 6.0 of this test report for a description of the radiated and antenna port conducted emissions tests. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the “Land Mobile FM or PM – Communications Equipment – Measurements and Performance Standards” (ANSI/TIA-603-C-2004) and “Measurement Guidance for Certification of Licensed Digital Transmitters” (KDB 971168 v02r01) were used in the measurement of the LG Portable Handset FCC ID: ZNFLS885. Deviation from Measurement Procedure…………………………………………………………………..None 3.2 Cellular - Base Frequency Blocks §22.905 A* A B A* B* Low High 869 880 890 894 BLOCK 1: 869 – 880 MHz (A* Low + A) BLOCK 3: 890 – 891.5 MHz (A* High) BLOCK 2: 880 – 890 MHz (B) BLOCK 4: 891.5 – 894 MHz (B*) 3.3 Cellular - Mobile Frequency Blocks §22.905 A* A B A* B* Low High 824 835 845 849 BLOCK 1: 824 – 835 MHz (A* Low + A) BLOCK 3: 845 – 846.5 MHz (A* High) BLOCK 2: 835 – 845 MHz (B) BLOCK 4: 846.5 – 849 MHz (B*) 3.4 PCS - Base Frequency Blocks §24.229 A D B E F C 1930 1950 1970 1990 BLOCK 1: 1930 – 1945 MHz (A) BLOCK 4: 1965 – 1970 MHz (E) BLOCK 2: 1945 – 1950 MHz (D) BLOCK 5: 1970 – 1975 MHz (F) BLOCK 3: 1950 – 1965 MHz (B) BLOCK 6: 1975 – 1990 MHz (C) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

3.5 PCS - Mobile Frequency Blocks §24.229 A D B E F C 1850 1870 1890 1910 BLOCK 1: 1850 – 1865 MHz (A) BLOCK 4: 1885 – 1890 MHz (E) BLOCK 2: 1865 – 1870 MHz (D) BLOCK 5: 1890 – 1895 MHz (F) BLOCK 3: 1870 – 1885 MHz (B) BLOCK 6: 1895 – 1910 MHz (C) 3.6 Radiated Measurements §2.1053 §22.913(a.2) §22.917(a) §24.232(c) §24.238(a) The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Clause 5, Figure 5.7 of ANSI C63.4-2009. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An ETS Lindgren Model 2188 raised turntable is used for radiated measurement. It is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. A 78cm high PVC support structure is placed on top of the turntable. A ¾” (~1.9cm) sheet of high density polyethylene is used as the table top and is placed on top of the PVC supports to bring the total height of the table to 80cm. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. For the EUT positioning, “H” is defined with the EUT lying flat on the test surface, “H2” is defined with the EUT standing up on its side, and “V” is defined with the EUT standing upright. Per the guidance of ANSI/TIA-603-C-2004, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. Radiated power levels are investigated with the receive antenna vertically polarized while radiated spurious emissions levels are investigated with the receive antenna horizontally and vertically polarized per ANSI/TIA-603-C-2004. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

4.0 TEST EQUIPMENT CALIB RATION DAT A Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number - RE1 Radiated Emissions Cable Set (UHF/EHF) 5/29/2014 Annual 5/29/2015 N/A Agilent 8449B (1-26.5GHz) Pre-Amplifier 5/11/2014 Annual 5/11/2015 3008A00985 Agilent 87405C Pre-amplifier (0.1 - 18 GHz) 3/19/2014 Annual 3/19/2015 MY53010007 Com-Power AL-130 9kHz - 30MHz Loop Antenna 6/26/2013 Biennial 6/26/2015 121034 Espec ESX-2CA Environmental Chamber 4/16/2014 Annual 4/16/2015 17620 ETS Lindgren 3117 1-18 GHz DRG Horn (Medium) 4/8/2014 Biennial 4/8/2016 125518 ETS Lindgren 3164-08 Quad Ridge Horn Antenna 3/12/2014 Biennial 3/12/2016 128337 K&L 13SH10-1000/U1000 N Type High Pass Filter 5/22/2014 Annual 5/22/2015 2 K&L 11SH10-3075/U18000 High Pass Filter 5/2/2014 Annual 5/2/2015 2 Mini-Circuits PWR-SENS-4RMS USB Power Sensor 4/17/2014 Annual 4/17/2015 11210140001 Mini-Circuits TVA-11-422 RF Power Amp N/A QA1303002 Rhode & Schwarz TS-PR18 Pre-Amplifier 6/12/2014 Annual 6/12/2015 101622 Rohde & Schwarz CMU200 Base Station Simulator N/A 836536/0005 Rohde & Schwarz TS-PR18 1-18 GHz Pre-Amplifier 3/5/2014 Annual 3/5/2015 100071 Rohde & Schwarz ESU40 EMI Test Receiver (40GHz) 5/21/2014 Annual 5/21/2015 100348 Schwarzbeck UHA 9105 Dipole Antenna (400 - 1GHz) Rx 11/1/2013 Biennial 11/1/2015 91052523RX Sunol JB5 Bi-Log Antenna (30M - 5GHz) 1/28/2014 Biennial 1/28/2016 A051107 VWR 62344-734 Thermometer with Clock 2/20/2014 Biennial 2/20/2016 140140336 Table 4-1. Test Equipment Note: Equipment with a calibration date of “N/A” shown in this list was not used to make direct calibrated measurements. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

5.0 S AMPLE CALCULATIONS CDMA Emission Designator Emission Designator = 1M25F9W CDMA BW = 1.25 MHz F = Frequency Modulation 9 = Composite Digital Info W = Combination (Audio/Data) (Measured at the 99.75% power bandwidth) Spurious Radiated Emission Example: Spurious emission at 3700.40 MHz The receive spectrum analyzer reading at 3 meters with the EUT on the turntable was –81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of –81.0 dBm on the spectrum analyzer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 3700.40 MHz. So 6.1 dB is added to the signal generator reading of –30.9 dBm yielding –24.80 dBm. The fundamental EIRP was 25.50 dBm so this harmonic was 25.50 dBm – (-24.80) = 50.3 dBc. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

6.0 TEST RESULTS 6.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFLS885 FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): CDMA FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result TRANSMITTER MODE (TX) 22.913(a.2) Effective Radiated Power < 7 Watts max. ERP PASS Section 6.2 Equivalent Isotropic 24.232(c) < 2 Watts max. EIRP RADIATED PASS Section 6.2 Radiated Power 2.1053 Radiated Spurious > 43 + log10 (P[Watts]) for all 22.917(a) PASS Section 6.3 Emissions out-of-band emissions 24.238(a) Table 6-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

6.2 Radiated Power (ERP/EIRP) §22.913(a)(2) 24.232(c) Test Overview Effective Radiated Power (ERP) and Equivalent Isotropic Radiated Power (EIRP) measurements are performed using the substitution method described in ANSI/TIA-603-C-2004 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically polarized broadband horn antennas. All measurements are performed as RMS average measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 v02r01 – Section 5.2.1 ANSI/TIA-603-C-2004 – Section 2.2.17 Test Settings 1. Radiated power measurements are performed using the signal analyzer’s “channel power” measurement capability for signals with continuous operation. For signals with burst transmission, the signal analyzer’s “time domain power” measurement capability is used 2. RBW = 1 – 5% of the expected OBW, not to exceed 1MHz 3. VBW ≥ 3 x RBW 4. Span = 1.5 times the OBW 5. No. of sweep points > 2 x span / RBW 6. Detector = RMS 7. Trigger is set to “free run” for signals with continuous operation with the sweep times set to “auto”. Trigger is set to enable triggering only on full power bursts with the sweep time set less than or equal to the transmission burst duration 8. The integration bandwidth was roughly set equal to the measured OBW of the signal for signals with continuous operation. For signals with burst transmission, the “gating” function was enabled to ensure that measurements are performed during times in which the transmitter is operating at its maximum power 9. Trace mode = trace averaging (RMS) over 100 sweeps 10. The trace was allowed to stabilize FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 6-1. Test Instrument & Measurement Setup Test Notes 1) This device was tested under all RC and SO combinations and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The worst case setup is reported in the tables below. Substitute Ant. Ant. ERP Frequency Battery EUT ERP ERP Margin Mode Level Gain Pol. Limit [MHz] Type Pol. [dBm] [Watts] [dB] [dBm] [dBd] [H/V] [dBm] 824.70 CDMA850 Standard 14.01 4.60 V H2 18.61 0.073 38.45 -19.84 836.52 CDMA850 Standard 12.43 4.82 V H2 17.25 0.053 38.45 -21.20 848.31 CDMA850 Standard 12.85 5.04 V H2 17.89 0.062 38.45 -20.56 Table 6-2. ERP (Cellular CDMA) Substitute Ant. Ant. EIRP Frequency Battery EUT EIRP EIRP Margin Mode Level Gain Pol. Limit [MHz] Type Pol. [dBm] [Watts] [dB] [dBm] [dBi] [H/V] [dBm] 1851.25 CDMA1900 Standard 13.24 5.07 V H2 18.31 0.068 33.01 -14.70 1880.00 CDMA1900 Standard 13.67 4.90 V H2 18.57 0.072 33.01 -14.44 1908.75 CDMA1900 Standard 12.75 4.84 V H2 17.59 0.057 33.01 -15.42 Table 6-3. EIRP (PCS CDMA) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

6.3 Radiated Spurious Emissions Measurements §2.1053 §22.917(a) 24.238(a) Test Overview Radiated spurious emissions measurements are performed using the substitution method described in ANSI/TIA-603-C-2004 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using vertically and vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically and horizontally polarized broadband horn antennas. All measurements are performed as peak measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 v02r01 – Section 5.8 ANSI/TIA-603-C-2004 – Section 2.2.12 Test Settings 1. RBW = 100kHz for emissions below 1GHz and 1MHz for emissions above 1GHz 2. VBW ≥ 3 x RBW 3. Span = 1.5 times the OBW 4. No. of sweep points > 2 x span / RBW 5. Detector = Peak 6. Trace mode = max hold 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 6-2. Test Instrument & Measurement Setup FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

Test Notes 1) This device was tested under all RC and SO combinations and the worst case is reported with RC3/SO55 with "All Up" power control bits. 2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The “H” positioning is defined with the EUT lying flat on the test surface, the “H2” positioning is defined with the EUT standing up on its side, and the “V” positioning is defined with the EUT standing upright. The worst case setup is reported in the tables below. 4) The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter using CISPR quasi peak detector below 1GHz. The worst-case emissions are reported. 5) Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. OPERATING FREQUENCY: 824.70 MHz CHANNEL: 1013 MEASURED OUTPUT POWER: 18.61 dBm = 0.073 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 31.61 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBd] [dBm] [H/V] [H/H2/V] [dBm] 1649.40 -45.07 3.61 -41.46 H H 60.1 2474.10 -55.74 3.57 -52.17 H H 70.8 Table 6-4. Radiated Spurious Data (Cellular CDMA Mode – Ch. 1013) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

OPERATING FREQUENCY: 836.52 MHz CHANNEL: 384 MEASURED OUTPUT POWER: 17.25 dBm = 0.053 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 30.25 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBd] [dBm] [H/V] [H/H2/V] [dBm] 1673.04 -49.93 3.53 -46.41 H H 63.7 2509.56 -55.15 3.57 -51.58 H H 68.8 Table 6-5. Radiated Spurious Data (Cellular CDMA Mode – Ch. 384) OPERATING FREQUENCY: 848.31 MHz CHANNEL: 777 MEASURED OUTPUT POWER: 17.89 dBm = 0.062 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 30.89 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBd] [dBm] [H/V] [H/H2/V] [dBm] 1696.62 -40.55 3.44 -37.11 H H 55.0 2544.93 -55.38 3.64 -51.74 H H 69.6 Table 6-6. Radiated Spurious Data (Cellular CDMA Mode – Ch. 777) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

OPERATING FREQUENCY: 1851.25 MHz CHANNEL: 25 MEASURED OUTPUT POWER: 18.31 dBm = 0.068 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 31.31 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBi] [dBm] [H/V] [H/H2/V] [dBm] 3702.50 -55.34 8.40 -46.94 H H 65.3 5553.75 -51.99 10.56 -41.43 H H 59.7 7405.00 -54.79 12.05 -42.73 H H 61.0 Table 6-7. Radiated Spurious Data (PCS CDMA Mode – Ch. 25) OPERATING FREQUENCY: 1880.00 MHz CHANNEL: 600 MEASURED OUTPUT POWER: 18.57 dBm = 0.072 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 31.57 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBi] [dBm] [H/V] [H/H2/V] [dBm] 3760.00 -55.18 8.38 -46.79 H H 65.1 5640.00 -53.59 10.70 -42.89 H H 61.2 7520.00 -54.95 12.10 -42.84 H H 61.2 Table 6-8. Radiated Spurious Data (PCS CDMA Mode – Ch. 600) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

OPERATING FREQUENCY: 1908.75 MHz CHANNEL: 1175 MEASURED OUTPUT POWER: 17.59 dBm = 0.057 W MODULATION SIGNAL: CDMA DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 30.59 Level at Substitute Spurious Ant. EUT Frequency Antenna Antenna Gain Emission Level Pol. Pol. [dBc] [MHz] Terminals [dBi] [dBm] [H/V] [H/H2/V] [dBm] 3817.50 -54.41 8.40 -46.00 H H 64.3 5726.25 -54.75 10.76 -43.99 H H 62.3 7635.00 -55.32 12.21 -43.10 H H 61.4 Table 6-9. Radiated Spurious Data (PCS CDMA Mode – Ch. 1175) FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014

7.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFLS885 complies with all the requirements of Parts 2, 22, 24 of the FCC rules. FCC Pt. 22 & 24 CDMA MEASUREMENT REPORT Reviewed by: FCC ID: ZNFLS885 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 18 0Y1406091173.ZNF 6/9-6/20/2014 Portable Handset © 2014 PCTEST Engineering Laboratory, Inc. V 1.2 06/03/2014


Document Created: 2019-10-21 23:28:02
Document Modified: 2019-10-21 23:28:02
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC