HAC RF Test Report6

FCC ID: ZNFLS770

Test Report

Download: PDF
FCCID_2576248

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Muitilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: CD835V3—1175_May14 CALIBRATION CERTIFICATE Object CD835V3 — SN: 1175 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: May 19, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37292783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Type—N mismatch combination SN: 5047.2 / 06327 03—Apr—14 (No. 217—01921) Apr—15 Probe ERSDVE6 SN: 2336 30—Dec—13 (No. ER3—2336_Dec13) Dec—14 Probe H3DV6 SN: 6065 30—Dec—13 (No. H3—6065_Dec13) Dec—14 DAE4 SN: 781 13—Sep—13 (No. DAE4—781_Sep13) Sep—14 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 4419B SN: GB42420191 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41495277 01—Apr—08 (in house check Oct—13) In house check: Oct—15 Power sensor HP 8482A SN: US37295597 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 RF generator R&S SMT—O6 SN: 832283/011 27—Aug—12 (in house check Oct—13) In house check: Oct—16 Name Function Signature Calibrated by: Israe El—Naouq Laboratory Technician Approved by: Fin Bomholt Deputy Technical Manager /7/ p 7. l//%; 2 Issued: May 20, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD835V3—1175_May14 Page 1 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Reference # ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: # Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. E—field distribution: E field is measured in the x—y—plane with an isotropic ERS3D—field probe with 100 mW forward power to the antenna feed point. in accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 90mm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one linge, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD835V3—1175_May14 Page 2 of 5

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15mm Scan resolution dx, dy = 5 mm Frequency 835 MHz + 1 MHz Input power drift < 0.05 dB Maximum Field values at 835 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 107.2 V/m = 40.60 dBV/m Averaged maximum above arm 100 mW input power 107.0 V/m + 12.8 % (k=2) Appendix Antenna Parameters Frequency Return Loss Impedance 800 MHz 16.4 dB 42.0 O — 11.5 jQ 835 MHz 26.5 dB 49.3 Q + 4.7 jQ 900 MHz 17.6 dB 56.9 Q — 12.4 jQ 950 MHz 19.7 dB 47.8 0 + 9.9 jQQ 960 MHz 14.6 dB 56.4 Q + 19.1 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD835V3—1175_May14 Page 3 of 5

Impedance Measurement Plot 19 May 2014 13:341:34 CH1i S11i LOG 5 dB/ REF —15 dB 2:—26,.458 dB 835.000 A0d MHz CH1 Mark ers 1:—16.390 de Cor $00.000 MHz 3:—17.570 dB 900.000 MHz 4:—19.703 dB 950.000 MHz Av 169 5:—14.609 dB 960.000 MHz H1d [cH2] s11 1 U FS 8$35.000 @ona MHz Del CH2 Markers 11 41.977 o Cor —11.529 800.9000 MHz Av 16" 3: 56.428 19.055 H1d 960.000 MH START 335.000 000 MHz STOP 1 335.050 000 MHz Certificate No: CD835V3—1175_May14 Page 4 of 5

DASY5 E—field Result Date: 19.05.2014 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1175 Communication System: UID 0 — CW; Frequency: 835 MHz Medium parameters used: 0 = 0 S/m, &, = 1; p = 1000 kg/m‘ Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2013; e Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 13.09.2013 e Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 835MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 123.3 V/m; Power Drift = 0.00 dB Applied MIF = 0.00 dB RF audio interference level = 40.60 dBV/m Emission category: M3 MIF scaled E—field Grid 1 M3 Grid 2 M3 Grid 3 M3 40.28 dBV/m|40.6 dBV/m 40.53 dBV/m Grid 4 M4 Grid 6 M4 35.86 dBV/m 36.02 dBV/m Grid 7 M3 Grid 9 M3 40.33 dBV/m|40.56 dBV/m 40.43 dBV/m —1.92 —3.84 —5.77 ~7.69 —9.61 0 dB = 107.2 V/m = 40.60 dBV/m Certificate No: CD835V3—1175_May14 Page 5 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: CD1880V3—1159_May14 CALIBRATION CERTIFICATE Object CD1880V3 — SN: 1159 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: May 19, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37292783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Type—N mismatch combination SN: 5047.2 / 06327 03—Apr—14 (No. 217—01921) Apr—15 Probe ER3DV6 SN: 2336 30—Dec—13 (No. ER3—2336_Dec13) Dec—14 Probe H3DV6 SN: 6065 30—Dec—13 (No. H3—6065_Dec13) Dec—14 DAE4 SN: 781 13—Sep—13 (No. DAE4—781_Sep13) Sep—14 Secondary Standards | 1D # Check Date (in house) Scheduled Check Power meter Agilent 4419B SN: GB42420191 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41495277 01—Apr—08 (in house check Oct—13) In house check: Oct—15 Power sensor HP 8482A SN: US37295597 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 RF generator R&S SMT—O6 SN: 832283/011 27—Aug—12 (in house check Oct—13) In house check: Oct—16 Name Function Signature Calibrated by: Israe El—Naouq Laboratory Technician O/%ca,. éWM, /. uho y Approved by: Fin Bomholt Deputy Technical Manager e /7’ z,~ Issued: May 20, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD1880V3—1159_May14 Page 1 of 7

Calibration Laboratory of \\\“\‘@7”@ Schweizerischer Kalibrierdienst Schmid & Partner iiafifiié Service suisse d‘étalonnage Engineering AG Z zm s Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 7A¥4evVe //_\\ S Swiss Calibration Service ,I/’llul u\\‘\\\ Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Reference e ANS1—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. * Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. * E—field distribution: E fietd is measured in the x—y—plane with an isotropic ER3D—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 9$Omm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD1880V3—1159_May14 Page 2 of 7

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm 1730 MHz +1 MHz Frequency 1880 MHz x 1 MHz Input power drift <0.05 dB Maximum Field values at 1730 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 97.7 V/m = 39.80 dBV/m Maximum measured above low end 100 mW input power 95.1 V/m = 39.57 dBV/m Averaged maximum above arm 100 mW input power 96.4 V/im + 12.8 % (k=2) Maximum Field values at 1880 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 90.3 V/m = 39.11 dBV/m Maximum measured above low end 100 mW input power 88.5 V/m = 38.94 dBV/m Averaged maximum above arm 100 mW input power 89.4 V/m + 12.8 % (k=2) Certificate No: CD1880V3—1159_May14 Page 3 of 7

Appendix Antenna Parameters Nominal Frequencies Frequency Return Loss Impedance 1730 MHz 34.4 dB 48.7 ) + 1.3 jQ 1880 MHz 18.7 dB 45.5 Q + 10.2 jQ 1900 MHz 18.9 dB 48.6 Q + 11.1 jQ 1950 MHz 23.7 dB 53.7 Q + 5.7 jQ 2000 MHz 24.1 dB 45.1 Q + 3.4 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD1880V3—1159_May14 Page 4 of 7

Impedance Measurement Plot 19 May 2014 13:38:34 CH] s1i1 Los 5 dB/REF —18 dB 21—18.680 dB 1 880.000 000 MHz CH1 Markers 1:—34.377_ dB Cor 1.730090 GHz 3:—18,937 dB 1.30090 GHz 4:—23.7 20 dB 1.95090 GHz Av 159 S:—24.063 dB 2,.00000 GHz H1d CH2 S11 1 U FS 2: 45.480 & 10.223 & 865.42 pH 1 $80.000 000 MHz sem Del CH2 Markers 11 48.664 & Cor 1.3281 & 1.73000 GHz 3: 48.572 4 111117 & 1.9900900 GHz Av 4: 53.705 ¢ 16° 5.6641 a 1.959080 GHz 3: 45,.086 a H1d 3.37 30 0 200000 GHz CENTER 1 880.000 000 MHz SPAN 1 a00.000 000 MHz Certificate No: CD1880V3—1159_May14 Page 5 of 7

DASY5 E—fie!ld Result Date: 19.05.2014 Test Laboratory: SPEAG Lab2 DUT: HAC Dipole 1880 MHz; Type: CD1880V3; Serial: CD1880V3 — SN: 1159 Communication System: UID 0 — CW; Frequency: 1730 MHz, Frequency: 1880 MHz Medium parameters used: 0 = 0 S/m, &, = 1; p = 1000 kg/m3 Phantom section: RF Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2013; e Sensor—Surface: (Fix Surface) * Electronics: DAE4 Sn781; Calibrated: 13.09.2013 * Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 * DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 1880MHz/E—Scan — 1730MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 151.6 V/m; Power Drift =—0.01 dB Applied MIF = 0.00 dB RF audio interference level = 39.80 dBV/m Emission category: M2 MIF scaled E—field Grid 1 M2 Grid 2 M2 Grid 3 M2 39.32 dBV/m|39.57 dBV/m|39.46 dBV/m Grid 4 M2 Grid 6 M2 37.52 dBV/m 37.79 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 39.56 dBV/m|39.8 dBV/m |39.7 dBV/m Certificate No: CD1880V3—1159_May14 Page 6 of 7

Dipole E—Field measurement @ 1880MHz/E—Scan — 1880MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 140.5 V/m; Power Drift = 0.01 dB Applied MIF = 0.00 dB RF audio interference level = 39.11 dBV/m Emission category: M2 MIF scaled E—field Grid 1 M2 Grid 2 M2 Grid 3 M2 38.71 dBV/m|38.94 dBV/m |38.84 dBV/m Grid 4 M2 Grid 6 M2 36.65 dBV/m 36.8 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 38.92 dBV/m|39.11 dBV/m|38.97 dBV/m —1.06 —2.13 —3.19 —~4.26 —5.32 0 dB = 97.72 V/m = 39.80 dBV/m Certificate No: CD1880V3—1159_May14 Page 7 of 7

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: CD2600V3—1008_Aug14 |CAL|BRAT|ON CERTIFICATE I Object CD2600V3 — SN: 1008 Calibration procedure(s) QGA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: August 21, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37292783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Type—N mismatch combination SN: 5047.2 / 06327 03—Apr—14 (No. 217—01921) Apr—15 Probe EF3DV3 SN: 4013 18—Jun—14 (No. EF3—4013_Jun14) Jun—15 DAE4 SN: 781 13—Sep—13 (No. DAE4—781_Sep13) Sep—14 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 4419B SN: GB42420191 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41495277 01—Apr—08 (in house check Oct—13) In house check: Oct—15 Power sensor HP 8482A SN: US37295597 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 RF generator R&S SMT—O6 SN: 832283/011 27—Aug—12 (in house check Oct—13) In house check: Oct—16 Name Function Signature Calibrated by: Michael Weber Laboratory Technician /yW E Approved by: Fin Bomholt Technical Manager % & zes // > Issued: August 22, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD2600V3—1008_Aug14 Page 1 of 5

Calibration Laboratory of l/m Schweizerischer Kalibrierdienst )F I, Schmid & Partner e 8 s Service suisse d‘étalonnage P Engineering AG e Servizio svizzero di taratura ’//I/ Zeughaussirasse 43, 8004 Zurich, Switzerland LXXX Swiss Calibration Service Zoliluts®® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates References [1] ANSI1—C63.19—2011 American National! Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 10 mm above the top edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter comnnected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. * Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. * E—field distribution: E field is measured in the x—y—plane with an isotropic ER3D—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 90mm). The sensor center is 10 mm (in z) above the top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, 10mm above the dipole surface. * H—field distribution: H—field is measured with an isotropic H—field probe with 100mW forward power to the antenna feed point, in the x—y—plane. The scan area and sensor distance is equivaient to the E—field scan. The maximum of the field is available at the center (subgrid 5) above the feed point. The H—field value stated as calibration value represents the maximum of the interpolated H—field, 10mm above the dipole surface at the feed point. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD2600V3—1008_Aug14 Page 2 of 5

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm Frequency 2600 MHz + 1 MHz Input power drift < 0.05 dB Maximum Field values at 2600 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 86.0 V/m = 38.69 dBV/m Maximum measured above low end 100 mW input power 85.1 V/m = 38.60 dBV/m Averaged maximum above arm 100 mW input power 85.6 V / m + 12.8 % (k=2) Appendix (Additional assessments outside the scope of SCS108) Antenna Parameters Frequency Return Loss Impedance 2450 MHz 22.0 dB 49.2 Q — 7.8 |Q 2550 MHz 26.8 dB 46.6 Q + 2.9 jQ 2600 MHz 26.1 dB 50.6 O + 4.9 jQ 2650 MHz 25.1 dB 54.3 Q + 4.0 jQ 2750 MHz 18.5 dB 60.8 Q — 7.6 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD2600V3—1008_Aug14 Page 3 of 5

Impedance Measurement Plot MA Aug 2014 1i4:48:16 CHI) s11 LOG 5 dB/REF —18 dB 3:1—26.126 dB 2 600.000 da@ MHz CH1 Markers 1:—22,.028 dB 245000 GHz Cor 2i—26.761 dB 2590900 GHz 4:—25.067 dB 2659000 GHz Avg 16 5:—18.490 dB 275000 GHz H1d CH2 S141 1 U FS 3 590.592 1 4.9375 6 302.24 pH 2 600,.000 deo MHz Del CH2 Markers 11 49.217 & Cor —7.8379 a 245900 GHz 2: 46.6095 ¢ 2.8974 a 255000 GHz Av 4: 54.260 6 169 3.9707 ¢ 265900 GHz 5: 60.828 & —7.37 23 i H1d 275000 GHz CENTER 2 600.000 0BO MHz SPAN 999.000 900 MHz Certificate No: CD2600V3—1008_Aug14 Page 4 of 5

DASY5 E—field Result Date: 21.08.2014 Test Laboratory: SPEAG Lab2 DUT: HAC Dipole 2600 MHz; Type: CD2600V3; Serial: CD2600V3 — SN: 1008 Communication System: UID 0 — CW ; Frequency: 2600 MHz Medium parameters used: o = 0 $/m, &, = 1; p = 1000 kg/m‘ Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: » Probe: EF3DV3 — SN4013; ConvF(1, 1, 1); Calibrated: 18.06.2014; * Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 13.09.2013 * Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 s DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole E—Field measurement @ 2600MHz — with EF_4013/E—Scan — 2600MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 67.44 V/m; Power Drift = —0.02 dB Applied MIF = 0.00 dB RF audio interference level = 38.69 dBV/m Emission category: M2 MIF scaled E—field Grid 1 M2 Grid 2 M2 Grid 3 M2 38.47 dBV/m 38.69 dBV/m 38.58 dBV/m Grid 4 M2 Grid 6 M2 37.95 dBV/m 38.02 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 38.43 dBV/m 38.6 dBV/m 38.46 dBV/m —1.40 cerhd —4.19 —5.58 —6.98 0 dB = 86.04 V/m = 38.69 dBV/m Certificate No: CD2600V3—1008_Aug14 Page 5 of 5


Document Created: 2015-03-16 22:49:42
Document Modified: 2015-03-16 22:49:42
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC