HAC RF Appendix 4

FCC ID: ZNFLS660

Test Report

Download: PDF
FCCID_2333033

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client UL CCS USA Certificate No: CD835V3—1014_Feb14 CALIBRATION CERTIFICATE Object CD835V3 — SN: 1014 Calibration procedure(s) QA CAL—20.v6 Calibration procedure for dipoles in air Calibration date: February 18, 2014 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A US37292783 09—Oct—13 (No. 217—01827) Oct—14 Power sensor HP 8481A MY41092317 09—Oct—13 (No. 217—01828) Oct—14 Reference 10 dB Attenuator SN: 5047.2 (10q) 04—Apr—13 (No. 217—01731) Apr—14 Probe ER3DV6 SN: 2336 30—Dec—13 (No. ER3—2336_Dec13) Dec—14 Probe H3DV6 SN: 6065 30—Dec—13 (No. H3—6065 Dec13) Dec—14 DAE4 SN: 781 13—Sep—13 (No. DAE4—781_Sep13) Sep—14 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 44198 SN: GB42420191 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Power sensor HP E4412A SN: MY41495277 01—Apr—08 (in house check Oct—13) In house check: Oct—15 Power sensor HP 8482A SN: US37295597 09—Oct—09 (in house check Oct—13) In house check: Oct—15 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—13) In house check: Oct—14 RF generator R&S SMT—O6 SN: 832283/011 27—Aug—12 (in house check Oct—13) In house check: Oct—15 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician W Approved by: Fin Bomholt Deputy Technical Manager / 5 7 /2aeil * Issued: February 18, 2014 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD835V3—1014_Feb14 Page 1 of 5

x o j s\\‘\i\__/;/7g s_ i |||ll t Calibration Laboratory of Schweizerischer Kalibrierdienst S L Schmid & Partner iifié Service suisse d‘étalonnage Engineering AG enzin 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland é/@\\? Swiss Calibration Service Alnlas® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates References [1] ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward power to the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional coupler. While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms paralle! below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS5 Surface Check job. Before the measurement, the distance between phantom suiface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a HP 8753E Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. * E—field distribution: E field is measured in the x—y—plane with an isotropic ER3D—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mim wide, its length exceeds the dipole arm length (180 or 90mm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one linge, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non—parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD835V3—1014_Feb14 Page 2 of 5

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.7 Phantom HAC Test Arch gLsr:?enrce Dipole Top — Probe Jaym Scan resolution dx, dy = 5 mm Frequency 835 MHz + 1 MHz Input power drift <0.05 dB Maximum Field values at 835 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 108.4 V / m Maximum measured above low end 100 mW input power 108.2 V / m Averaged maximum above arm 100 mW input power 108.3 V / m + 12.8 % (k=2) Appendix Antenna Parameters Frequency Return Loss Impedance 800 MHz 15.2 dB 41.9 t — 14.0 jQ 835 MHz 25.4 dB 50.2 O + 5.4 |Q 900 MHz 17.8 dB 54.2 Q — 12.8 |Q 950 MHz 18.7 dB 43.5 Q + 8.8 jQ 960 MHz 14.2 dB 49.9 Q + 19.9 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD835V3—1014_Feb14 Page 3 of 5

Impedance Measurement Plot 18 Feb 2014 12147134 LOG 5 dB~" REF —15 dB 7:—25,419 dB 35,.000 00B MHz CH1 Markers 1:—15.222 dB ©$30.000 MHz 3:—17.,809 dB 9900.000 MHz 4:—18.7 24 dB 950,000 MHz Av 1&9 5:—14.136 dB 960.9000 MHz H1d CH2] §11 1 U FS 2 59.195 ¢ 5.3711 & 1.9238 mH $35.000 GBo MHz z. C De 1 CH2 Markers 1: 41.936 ¢ Cor Aw 16 * HI d START 335.000 900 MHz STOP 1 335.000 0090 MHz Certificate No: CD835V3—1014_Febi4 Page 4 of 5

DASY5 E—field Result Date: 18.02.2014 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1014 Communication System: UID 10000, CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium: Air Medium parameters used: o = 0 S/m, & = 1; p = 1000 kg/m‘ Phantom section: RF Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: Probe: ER3DV6 — SN2336; ConvF(1, 1, 1); Calibrated: 30.12.2013; Sensor—Surface: (Fix Surface) o Electronics: DAE4 Sn781; Calibrated: 13.09.2013 *# Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 «& Measurement SW: DASY52, Version 52.8 (7) a SEMCAD X Version 14.6.10 (7164) Dipole E—Field measurement @ $35MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 126.2 V/m; Power Drift = 0.01 dB PMR not calibrated. PMF = 1.000 is applied. E—field emissions = 108.4 V/m Near—field category: M4 (AWF 0 dB) PMF scaled E—field Grid 1 M4 [Grid 2 M4 |Grid 3 M4 104.8 V/m|108.4 V/m|107.5 V/m Grid 4 M4 63.65 V/m Grid 7 M4 |Grid 8 M4 Grid 9 M4 103.7 V/m|108.2 V/m|107.9 V/m ~1.87 —3.74 —5.61 0 dB = 108.4 V/m = 40.70 dBV/m Certificate No: CD835V3—1014_Feb14 Page 5 of 5


Document Created: 2014-03-13 16:12:55
Document Modified: 2014-03-13 16:12:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC