Bluetooth LE Test Report

FCC ID: ZNFL413DL

Test Report

Download: PDF
FCCID_3726442

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC PART 15.247 Bluetooth (Low Energy) Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 11/20 - 12/18/2017 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab. Columbia, MD, USA United States Test Report Serial No.: 1M1712050312-05-R1.ZNF FCC ID: ZNFL413DL APPLICANT: LG Electronics MobileComm U.S.A Application Type: Class II Permissive Change Model: LML413DL Additional Model(s): LM-L413DL, L413DL, LM-X410ULMG, LMX410ULMG, X410ULMG EUT Type: Portable Handset Frequency Range: 2402 – 2480MHz FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15 Subpart C (15.247) Test Procedure(s): ANSI C63.10-2013, KDB 558074 D01 v04 Class II Permissive Change: Please see FCC change document This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013 and KDB 558074 D01 v04. Test results reported herein relate only to the item(s) tested. This test report (S/N: 1M1712050312-05-R1.ZNF) supersedes and replaces all previous versions of this test report. Please dispose of all previous versions of this test report accordingly. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 INTRODUCTION .......................................................................................................................................... 3 1.1 Scope ................................................................................................................................................................... 3 1.2 PCTEST Test Location ......................................................................................................................................... 3 1.3 Test Facility / Accreditations ................................................................................................................................. 3 2.0 PRODUCT INFORMATION.......................................................................................................................... 4 2.1 Equipment Description ......................................................................................................................................... 4 2.2 Device Capabilities ............................................................................................................................................... 4 2.3 Test Configuration ................................................................................................................................................ 4 2.4 EMI Suppression Device(s)/Modifications ............................................................................................................ 4 3.0 DESCRIPTION OF TESTS .......................................................................................................................... 5 3.1 Evaluation Procedure ........................................................................................................................................... 5 3.2 Radiated Emissions .............................................................................................................................................. 5 3.3 Environmental Conditions..................................................................................................................................... 5 4.0 ANTENNA REQUIREMENTS ...................................................................................................................... 6 5.0 MEASUREMENT UNCERTAINTY ............................................................................................................... 7 6.0 TEST EQUIPMENT CALIBRATION DATA .................................................................................................. 8 7.0 TEST RESULTS ........................................................................................................................................... 9 7.1 Summary .............................................................................................................................................................. 9 7.2 Radiated Spurious Emission Measurements ...................................................................................................... 10 7.3 Radiated Restricted Band Edge Measurements ................................................................................................. 15 8.0 CONCLUSION ............................................................................................................................................ 16 MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science and Economic Development Canada. 1.2 PCTEST Test Location These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules.  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS).  PCTEST facility is a registered (22831) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LGE Portable Handset FCC ID: ZNFL413DL. The data found in this test report was taken with the EUT operating in Bluetooth low energy mode. While in low energy mode, the Bluetooth transmitter hops pseudo-randomly between 40 channels, three of which are “advertising channels”. When the transmitter is hopping only between the three advertising channels, the EUT does not fall under the category of a “hopper” as defined in 15.247(a)(iii) which states that a “frequency hopping systems in the 2400–2483.5 MHz band shall use at least 15 channels.” As operation on only the advertising channels does not qualify the EUT as a hopper, the EUT is certified as a DTS device in this mode. The data found in this report is representative of the device when it transmits on its advertising channels. Typical Bluetooth operation is covered under the DSS report found with this application. Test Device Serial No.: 18379, 18320 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A (BC0, BC1), 850/1900 GSM/GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi- band LTE, 802.11b/g/n WLAN, Bluetooth (1x, EDR, LE) Ch. Frequency (MHz) 0 2402 : : 19 2440 : : 39 2480 Table 2-1. Frequency / Channel Operations 2.3 Test Configuration The EUT was tested per the guidance of ANSI C63.10-2013 and KDB 558074 D01 v04. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing. See Section 3.2 for radiated emissions test setups. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices (ANSI C63.10-2013) and the guidance provided in KDB 558074 D01 v04 were used in the measurement of the EUT. Deviation from measurement procedure…………………………………………….....................................None 3.2 Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. An 80cm tall test table made of Styrodur is placed on top of the turn table. For measurements above 1GHz, an additional Styrodur pedestal is placed on top of the test table to bring the total table height to 1.5m. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, mode of operation, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. 3.3 Environmental Conditions The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna(s) of the EUT are permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The EUT complies with the requirement of §15.203. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (±dB) Conducted Bench Top 1.13 Measurements Line Conducted Disturbance 3.09 Radiated Disturbance (<1GHz) 4.98 Radiated Disturbance (>1GHz) 5.07 Radiated Disturbance (>18GHz) 5.09 MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5- 2017. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number ‐ RE1 Radiated Emissions Cable Set (UHF/EHF) 6/21/2017 Annual 6/21/2018 RE1 Com‐Power AL‐130 9kHz ‐ 30MHz Loop Antenna 10/10/2017 Biennial 10/10/2019 121034 Emco 3115 Horn Antenna (1‐18GHz) 3/10/2016 Biennial 3/10/2018 9704‐5182 EMCO 3160‐09 Small Horn (18 ‐ 26.5GHz) 8/23/2016 Biennial 8/23/2018 135427 Rohde & Schwarz TS‐PR8 30 MHz‐8 GHz Pre‐Amplifier 12/22/2016 Annual 12/21/2017 102324 Rohde & Schwarz TS‐PR26 18‐26.5 GHz Pre‐Amplifier 5/11/2017 Annual 5/11/2018 100040 Rohde & Schwarz SFUNIT‐Rx Shielded Filter Unit 7/3/2017 Annual 7/3/2018 102135 Rohde & Schwarz SFUNIT‐Rx Shielded Filter Unit 7/3/2017 Annual 7/3/2018 102134 Rohde & Schwarz FSW67 Signal / Spectrum Analyzer 8/11/2017 Annual 8/11/2018 103200 Rohde & Schwarz ESU26 EMI Test Receiver (26.5GHz) 4/19/2017 Annual 4/19/2018 100342 Rohde & Schwarz ESU40 EMI Test Receiver (40GHz) 7/31/2017 Annual 7/31/2018 100348 Seekonk NC‐100 Torque Wrench 5/16", 8" lbs 3/2/2016 Biennial 3/2/2018 N/A Sunol DRH‐118 Horn Antenna (1‐18 GHz) 8/11/2017 Biennial 8/11/2019 A042511 Sunol JB5 Bi‐Log Antenna (30M ‐ 5GHz) 3/14/2016 Biennial 3/14/2018 A051107 Table 6-1. Annual Test Equipment Calibration Schedule Notes: 1. For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. 2. Equipment with a calibration date of “N/A” shown in this list was not used to make direct calibrated measurements. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 TEST RESULTS 7.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFL413DL FCC Classification: Digital Transmission System (DTS) Number of Channels: 40 FCC Part Test Test RSS Section(s) Test Description Test Limit Reference Section(s) Condition Result General Field Strength Emissions in restricted 15.205 Limits (Restricted Bands bands must meet the Sections 7.2, RSS-Gen [8.9] RADIATED PASS 15.209 and Radiated Emission radiated limits detailed in 7.3 Limits) 15.209 (RSS-Gen [8.9]) Table 7-1. Summary of Test Results Notes: 1. All modes of operation were investigated. The test results shown in the following sections represent the worst case emissions. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.2 Radiated Spurious Emission Measurements §15.205 §15.209 §15.247(d); RSS-Gen [8.9] Test Overview and Limit All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive antenna while the EUT is operating at maximum power and at the appropriate frequencies. Only the radiated emissions of the configuration that produced the worst case emissions are reported in this section. All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR and Table 6 of RSS-Gen (8.10) must not exceed the limits shown in Table 7-2 per Section 15.209 and RSS- Gen (8.9). Field Strength Measured Distance Frequency [V/m] [Meters] 0.009 – 0.490 MHz 2400/F (kHz) 300 0.490 – 1.705 MHz 24000/F (kHz) 30 1.705 – 30.00 MHz 30 30 30.00 – 88.00 MHz 100 3 88.00 – 216.0 MHz 150 3 216.0 – 960.0 MHz 200 3 Above 960.0 MHz 500 3 Table 7-2. Radiated Limits Test Procedures Used ANSI C63.10-2013 – Section 6.6.4.3 KDB 558074 D01 v04 – Section 12.1, 12.2.7 Test Settings Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3kHz > 1/T 4. Averaging type was set to RMS to ensure that video filtering was applied in the power domain 5. Detector = peak 6. Sweep time = auto 7. Trace mode = max hold 8. Trace was allowed to run for at least 50 times (1/duty cycle) traces MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW is set depending on measurement frequency, as specified in Table 7-3 below 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize Frequency RBW 9 – 150kHz 200 – 300Hz 0.15 – 30MHz 9 – 10kHz 30 – 1000MHz 100 – 120kHz > 1000MHz 1MHz Table 7-3. RBW as a Function of Frequency Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-1. Radiated Test Setup >1GHz MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Notes 1. The optional test procedures for antenna port conducted measurements of unwanted emissions per the guidance of KDB 558074 D01 v04 were not used to evaluate this device for compliance to radiated limits. All radiated spurious emissions levels were measured in a radiated test setup. 2. All emissions lying in restricted bands specified in §15.205 and Section 8.10 of RSS-Gen are below the limit shown in Table 7-2. 3. The antenna is manipulated through typical positions, polarity and length during the tests. The EUT is manipulated through three orthogonal planes. 4. This unit was tested with its standard battery. 5. The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter using CISPR quasi peak detector below 1GHz. Above 1 GHz, average and peak measurements were taken using linearly polarized horn antennas. The worst-case emissions are reported however emissions whose levels were not within 20dB of the respective limits were not reported. 6. Average measurements were recorded using a VBW of 3kHz, per Section 12.2.5.3 of KDB 558074 D01 v04 and Section 4.1.4.2.3 of ANSI C63.10-2013, since 1/T is equal to just under 3kHz. This method was used because the EUT could not be configured to operate with a duty cycle > 98%. Both average and peak measurements were made using a peak detector 7. Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. 8. No significant radiated band edge emissions were found in the 2310 – 2390MHz restricted band. 9. The "-" shown in the following RSE tables are used to denote a noise floor measurement. Sample Calculations Determining Spurious Emissions Levels o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] o Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] Radiated Band Edge Measurement Offset o The amplitude offset shown in the radiated restricted band edge plots in Section 7.3 was calculated using the formula: Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) – Preamplifier Gain MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Radiated Spurious Emission Measurements §15.205 §15.209 §15.247(d); RSS-Gen [8.9] Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2402MHz Channel: 0 Ant. Antenna Turntable Analyzer Field Frequency AFCL Limit Margin Detector Pol. Height Azimuth Level Strength [MHz] [dB/m] [dBμV/m] [dB] [H/V] [cm] [degree] [dBm] [dBμV/m] 4804.00 Avg H - - -77.92 2.42 31.50 53.98 -22.47 4804.00 Peak H - - -65.91 2.42 43.51 73.98 -30.46 12010.00 Avg H - - -79.72 13.48 40.76 53.98 -13.22 12010.00 Peak H - - -67.46 13.48 53.02 73.98 -20.96 Table 7-4. Radiated Measurements @ 3 meters Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2440MHz Channel: 19 Ant. Antenna Turntable Analyzer Field Frequency AFCL Limit Margin Detector Pol. Height Azimuth Level Strength [MHz] [dB/m] [dBμV/m] [dB] [H/V] [cm] [degree] [dBm] [dBμV/m] 4880.00 Avg H - - -78.23 3.27 32.04 53.98 -21.94 4880.00 Peak H - - -66.43 3.27 43.84 73.98 -30.14 7320.00 Avg H - - -79.74 9.70 36.96 53.98 -17.02 7320.00 Peak H - - -67.67 9.70 49.03 73.98 -24.95 12200.00 Avg H - - -79.89 14.01 41.12 53.98 -12.86 12200.00 Peak H - - -68.23 14.01 52.78 73.98 -21.20 Table 7-5. Radiated Measurements @ 3 meters MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Radiated Spurious Emission Measurements §15.205 §15.209 §15.247(d); RSS-Gen [8.9] Bluetooth Mode: LE Distance of Measurements: 3 Meters Operating Frequency: 2480MHz Channel: 39 Ant. Antenna Turntable Analyzer Field Frequency AFCL Limit Margin Detector Pol. Height Azimuth Level Strength [MHz] [dB/m] [dBμV/m] [dB] [H/V] [cm] [degree] [dBm] [dBμV/m] 4960.00 Avg H - - -78.24 2.62 31.38 53.98 -22.60 4960.00 Peak H - - -66.01 2.62 43.61 73.98 -30.37 7440.00 Avg H - - -79.31 9.48 37.17 53.98 -16.81 7440.00 Peak H - - -67.99 9.48 48.49 73.98 -25.49 12400.00 Avg H - - -80.03 12.93 39.90 53.98 -14.08 12400.00 Peak H - - -67.45 12.93 52.48 73.98 -21.50 Table 7-6. Radiated Measurements @ 3 meters MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.3 Radiated Restricted Band Edge Measurements §15.205 §15.209; RSS-Gen [8.9] The radiated restricted band edge measurements are measured with an EMI test receiver connected to the receive antenna while the EUT is transmitting. The amplitude offset shown in the following plots for average measurements was calculated using the formula: Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) – Preamplifier Gain Bluetooth Mode: LE Measurement Distance: 3 Meters Operating Frequency: 2480MHz Channel: 39 Plot 7-1. Radiated Restricted Upper Band Edge Plot 7-2. Radiated Restricted Upper Band Edge Measurement (Average) Measurement (Peak) MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 CONCLUSION The data collected relate only the item(s) tested and show that the LGE Portable Handset FCC ID: ZNFL413DL is in compliance with Part 15 Subpart C (15.247) of the FCC Rules. MEASUREMENT REPORT Approved by: FCC ID: ZNFL413DL (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 16 1M1712050312-05-R1.ZNF 11/20 - 12/18/2017 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 7.2 11/20/2017 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2019-10-09 03:26:00
Document Modified: 2019-10-09 03:26:00
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC