Test Report

FCC ID: ZNFG710TM

Test Report

Download: PDF
FCCID_3842888

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC PART 15.225 / ISED RSS-210 NFC Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 4/2/2018-4/16/2018 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab. Columbia, MD, USA United States Test Report Serial No.: 1M1804030060-10.ZNF FCC ID: ZNFG710TM IC: 2703C-G710AWM APPLICANT: LG Electronics MobileComm U.S.A Application Type: Class II Permissive Change Model: LM-G710TM Additional Model(s): LMG710TM, G710TM, LM-G710AWM, LMG710AWM, G710AWM, LM-G710RM, LMG710RM, G710RM HVIN: LM-G710AWM, LMG710AWM, G710AWM EUT Type: Portable Handset Frequency: 13.56MHz FCC Classification: Low Power Communications Device Transmitter (DXX) FCC Rule Part(s): Part 15 Subpart C (15.225) ISED Specification: RSS-210 Issue 9 Test Procedure(s): ANSI C63.10-2013 Class II Permissive Change: Please see FCC change document This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 Introduction ...................................................................................................................................... 3 1.1 Scope..................................................................................................................................................... 3 1.2 PCTEST Test Location .......................................................................................................................... 3 1.3 Test Facility / Accreditations .................................................................................................................. 3 2.0 PRODUCT INFORMATION ............................................................................................................. 4 2.1 Equipment Description ........................................................................................................................... 4 2.2 Device Capabilities ................................................................................................................................ 4 2.3 Test Configuration ................................................................................................................................. 4 2.4 EMI Suppression Device(s)/Modifications.............................................................................................. 4 3.0 DESCRIPTION OF TEST ................................................................................................................ 5 3.1 Evaluation Procedure ............................................................................................................................ 5 3.2 Radiated Emissions ............................................................................................................................... 5 3.3 Environmental Conditions ...................................................................................................................... 5 4.0 ANTENNA REQUIREMENTS .......................................................................................................... 6 5.0 MEASUREMENT UNCERTAINTY .................................................................................................. 7 6.0 TEST EQUIPMENT CALIBRATION DATA ...................................................................................... 8 7.0 TEST DATA ..................................................................................................................................... 9 7.1 Summary ............................................................................................................................................... 9 7.2 In-Band Radiated Spurious Emission Measurements .......................................................................... 10 7.3 Radiated Spurious Emission Measurements, Out-of-Band .................................................................. 13 8.0 CONCLUSION ............................................................................................................................... 19 MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science and Economic Development Canada. 1.2 PCTEST Test Location These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules.  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS).  PCTEST facility is a registered (2451B) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFG710TM. The test data contained in this report pertains only to the emissions due to the NFC transmitter of the EUT. Test Device Serial No.: 09811 2.2 Device Capabilities This device contains the following capabilities: 850/1900 GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n WLAN, 802.11a/n/ac UNII, Bluetooth (1x, EDR, LE), NFC 2.3 Test Configuration The EUT was set to continuously transmit at 13.56MHz. This was performed using manufacturer software loaded on the phone and a passive RFID tag to allow for continuous transmission. This device was tested in accordance with the guidance of ANSI C63.10-2013. See Section 3.2 of this test report for a description of the radiated emissions test setups.. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 DESCRIPTION OF TEST 3.1 Evaluation Procedure The measurement procedure described in the American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices (ANSI C63.10-2013) was used in the measurement of the EUT. Deviation from measurement procedure…………………………………………….....................................None 3.2 Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. An 80cm tall test table made of Styrodur is placed on top of the turn table. For measurements above 1GHz, an additional Styrodur pedestal is placed on top of the test table to bring the total table height to 1.5m. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33 depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, mode of operation, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. 3.3 Environmental Conditions The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna of the EUT are permanently attached.  This unit was tested with its standard battery. Conclusion: The EUT complies with the requirement of §15.203. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (±dB) Line Conducted Disturbance 3.09 Radiated Disturbance (<1GHz) 4.98 MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5- 2017. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number Agilent N9020A MXA Signal Analyzer 1/24/2018 Annual 1/24/2019 US46470561 Agilent N9038A MXE EMI Receiver 4/26/2017 Annual 4/26/2018 MY51210133 Com‐Power AL‐130 9kHz ‐ 30MHz Loop Antenna 10/10/2017 Biennial 10/10/2019 121034 Rohde & Schwarz ESU26 EMI Test Receiver (26.5GHz) 4/19/2017 Annual 4/19/2018 100342 Rohde & Schwarz TS‐PR8 Preamplifier‐Antenna SYS; 30MHz‐8GHz 10/19/2017 Annual 10/19/2018 102324 Sunol Sciences JB6 JB6 Antenna 9/27/2016 Biennial 9/27/2018 A082816 Table 6-1. Annual Test Equipment Calibration Schedule Note: For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 TEST DATA 7.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFG710TM FCC Classification: Low Power Communications Device Transmitter (DXX) Frequencies Examined: 13.56MHz FCC Part Test Test RSS Section(s) Test Description Test Limit Reference Section(s) Condition Result 15,848µV/m @ 30m 13.553 – 13.567 MHz 334µV/m @ 30m 15.225 13.410 – 13.553 MHz RSS-210 [B.6] In-Band Emissions Section 7.2 (a)(b)(c) 13.567 – 13.710 MHz 106µV/m @ 30m 13.110 – 13.410 MHz 13.710 – 14.010 MHz RADIATED PASS Emissions outside of the specified band (13.110 – 15.225 (d) 14.010 MHz) must meet RSS-Gen [8.9] Out-of-Band Emissions Section 7.3 15.209 the radiated limits detailed in 15.209 (RSS- Gen [8.9]) Table 7-1. Summary of Test Results MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.2 In-Band Radiated Spurious Emission Measurements §15.225(a)(b)(c); RSS-210 (B.6) Test Overview and Limit The EUT was tested from 13.110 – 14.010 MHz. All in-band radiated spurious emissions are measured with a spectrum analyzer connected to a loop antenna while the EUT is operating at appropriate frequencies. Only the radiated emissions of the configuration that produced the worst case emissions are reported in this section. All in-band emissions appearing in a restricted band as specified in Section 15.225 of the Title 47 CFR must not exceed the limits shown in Table 7-2. Frequency Field Strength Measured Distance [MHz] [V/m] [Meters] 13.553-13.567 MHz 15,848 30 13.410-13.553 MHz and 334 30 13.567-13.710 MHz 13.110-13.410 MHz and 106 30 13.710-14.010 MHz Table 7-2. Radiated Limits Test Procedures Used ANSI C63.10-2013 – Section 6.4.7 Test Settings 1. RBW = 9kHz 2. VBW ≥ 3 x RBW 3. Detector = peak 4. Sweep time = auto couple 5. Trace mode = max hold 6. Trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-1. Radiated Test Setup Test Notes: 1. All emissions lying in restricted bands specified in §15.225 and RSS-210 are below the limit shown in Table 7-2. 2. All measurements were performed using a loop antenna. The antenna was positioned in three orthogonal positions (X front, Y side, Z top) and the position with the highest emission level was recorded. 3. The EUT was positioned in three orthogonal planes to determine the orientation resulting in the worst case emissions. 4. Measurements were performed at 3m and the data was extrapolated to the specified measurement distance of 30m using the square of an inverse linear distance extrapolation factor (40 dB/decade) as specified in §15.31(f)(2). Extrapolation Factor = 20 log10(30/3)2 = 40dB. 5. The spectrum was investigated from 9kHz up to 30MHz using the loop antenna. Only the emissions shown in the table below were found to be significant. 6. All measurements were recorded using a spectrum analyzer employing a quasi-peak detector. 7. The "-" shown in the following RSE tables are used to denote a noise floor measurement. Sample Calculation o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] o Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

In-Band Radiated Spurious Emission Measurements §15.225(a)(b)(c); RSS-210 (B.6) Frequency: 13.56MHz Measurement Distance: 3 Meters Ant. Antenna Turntable 3m Field 30m Field Frequency Level AFCL Limit Limit Margin Pol. Height Azimuth Strength Strength [MHz] [dBm] [dB/m] [µV/m] [dBµV/m] [dB] [X/Y/Z] [cm] [degree] [dBµV/m] [dBµV/m] 13.273 Y 100 282 -91.47 14.73 30.26 -9.74 106.00 40.51 -50.25 13.351 Y 100 282 -92.68 14.71 29.03 -10.97 106.00 40.51 -51.48 13.433 Y 100 282 -91.91 14.69 29.78 -10.22 334.00 50.47 -60.69 13.560 Y 100 282 -70.99 14.66 50.67 10.67 15848.00 84.00 -73.32 13.659 Y 100 282 -90.82 14.64 30.82 -9.18 334.00 50.47 -59.65 13.776 Y 100 282 -91.32 14.62 30.30 -9.70 106.00 40.51 -50.21 13.829 Y 100 282 -91.39 14.61 30.22 -9.78 106.00 40.51 -50.29 Table 7-3. In-Band Radiated Measurements MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.3 Radiated Spurious Emission Measurements, Out-of-Band §15.209 §15.225(d); RSS-Gen (8.9) Test Overview and Limit The EUT was tested from 9kHz up to the 1GHz excluding the band 13.110 – 14.010 MHz. All measurements up to 960MHz were recorded with a spectrum analyzer employing a quasi-peak detector. All out-of-band emissions appearing in a restricted band as specified in Section 15.225 of the Title 47 CFR must not exceed the limits shown in Table 7-4 per Section 15.209. Field Strength Measured Distance Frequency [V/m] [Meters] 0.009 – 0.490 MHz 2400/F (kHz) 300 0.490 – 1.705 MHz 24000/F (kHz) 30 1.705 – 30.00 MHz 30 30 30.00 – 88.00 MHz 100 3 88.00 – 216.0 MHz 150 3 216.0 – 960.0 MHz 200 3 Above 960.0 MHz 500 3 Table 7-4. Radiated Limits – Out of band Test Procedures Used ANSI C63.10-2013 – Section 6.5.4 Test Settings 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 9kHz for emissions below 30MHz and 100kHz for emissions between 30MHz and 1GHz 3. VBW ≥ 3 x RBW 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Radiated Test Setup < 30MHz Figure 7-3. Radiated Test Setup > 30MHz MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Notes: 1. All measurements were recorded using a spectrum analyzer employing a quasi-peak detector for emissions below 960MHz. 2. A loop antenna was used to investigate emissions below 30MHz. 3. Both Vertical and Horizontal polarities of the receive antenna were evaluated with the worst case emissions being reported. Below 30MHz the loop antenna was positioned in 3 orthogonal planes (X front, Y side, Z top) to determine the orientation resulting in the worst case emissions. 4. The EUT was positioned in three orthogonal planes to determine the orientation resulting in the worst case emissions. 5. The spectrum is measured from 9kHz to the 10th harmonic and the worst-case emissions are reported. 6. No spurious emissions levels were found to be greater than the level of the fundamental. 7. The "-" shown in the following RSE tables are used to denote a noise floor measurement. Sample Calculation o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] o Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Radiated Spurious Emission Measurements, Out-of-Band §15.209 §15.225(d); RSS-Gen (8.9) Plot 7-1. Radiated Spurious Plot 9kHz – 30MHz (Pol. X) Plot 7-2. Radiated Spurious Plot 9kHz – 30MHz (Pol. Y) Plot 7-3. Radiated Spurious Plot 9kHz – 30MHz (Pol. Z) MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-4. Radiated Spurious Plot 30MHz – 1GHz MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Radiated Spurious Emission Measurements, Out-of-Band §15.209 §15.225(d); RSS-Gen (8.9) Tx Frequency 13.56MHz Measurement Distance: 3 Meters Ant. Antenna Turntable 3m Field Frequency Level AFCL Limit Margin Pol. Height Azimuth Strength [MHz] [dBm] [dB/m] [dBµV/m] [dB] [H/V] [cm] [degree] [dBµV/m] 27.12 Y - - -84.67 13.21 35.54 69.54 -34.00 40.68 V - - -97.85 -16.73 -7.58 40.00 -47.58 54.24 V - - -97.04 -22.49 -12.53 40.00 -52.53 67.80 V - - -96.91 -22.05 -11.96 40.00 -51.96 81.36 V - - -97.16 -22.62 -12.78 40.00 -52.78 94.92 V - - -97.44 -21.64 -12.08 43.52 -55.60 108.48 V - - -96.24 -18.21 -7.45 43.52 -50.97 Table 7-5. Radiated Measurements MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 20 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFG710TM has been tested to show compliance with Part 15 Subpart C (15.225) of the FCC Rules and RSS-210 of the Innovation, Science and Economic Development Canada Rules. MEASUREMENT REPORT Approved by: FCC ID: ZNFG710TM (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 19 1M1804030060-10.ZNF 4/2/2018-4/16/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 04/05/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2018-05-08 09:31:31
Document Modified: 2018-05-08 09:31:31
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC