Test Report

FCC ID: ZNFE971

Test Report

Download: PDF
FCCID_1824064

PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 15.225 / IC RSS-210 NFC Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A October 02, 2012 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0Y1209201382.ZNF FCC ID: ZNFE971 APPLICANT: LG Electronics MobileComm U.S.A Application Type: Class II Permissive Change Model(s): E971, LGE971, LG-E971 EUT Type: Portable Handset Frequency: 13.56MHz FCC Classification: Low Power Communications Device Transmitter (DXX) FCC Rule Part(s): FCC Part 15 Subpart C (15.225) IC Specification(s): RSS-210 Issue 8 Test Procedure(s): ANSI C63.4- 2009 Class II Permissive Change: Please see FCC change document. Original Grant Date: October 18, 2012 The device bearing the FCC Identifier specified above has been shown to comply with the applicable technical standards as indicated in the measurement report and has been tested in accordance with the measurement procedures specified in ANSI C63.4-2009 (See Test Report). These measurements were performed with no deviation from the standards. Test results reported herein relate only to the item(s) tested. I authorize and attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. NVLAP accreditation does not constitute any product endorsement by NVLAP or any agency of the United States Government. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. PCTEST certifies that no party to this application has been subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 1 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

T A B L E O F C O N T E N T S FCC Part 15.225 MEASUREMENT REPORT………….………...………………………………………………3 1.0 INTRODUCTION ..............................................................................................................................4 1.1 SCOPE .................................................................................................................................................. 4 1.2 PCTEST TEST LOCATION ................................................................................................................... 4 2.0 PRODUCT INFORMATION..............................................................................................................5 2.1 EQUIPMENT DESCRIPTION ................................................................................................................ 5 2.2 DEVICE CAPABILITIES ........................................................................................................................ 5 2.3 TEST CONFIGURATION ...................................................................................................................... 5 2.4 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ............................................................................. 5 2.5 LABELING REQUIREMENTS ............................................................................................................... 5 3.0 DESCRIPTION OF TEST.................................................................................................................6 3.1 EVALUATION PROCEDURE ................................................................................................................ 6 3.2 RADIATED EMISSIONS........................................................................................................................ 7 4.0 ANTENNA REQUIREMENTS ..........................................................................................................8 5.0 SAMPLE CALCULATIONS ..............................................................................................................9 5.1 RADIATED EMISSION MEASUREMENT SAMPLE CALCULATION.................................................... 9 6.0 TEST EQUIPMENT CALIBRATION DATA ....................................................................................10 7.0 ENVIRONMENTAL CONDITIONS .................................................................................................11 8.0 TEST DATA ....................................................................................................................................12 8.1 SUMMARY .......................................................................................................................................... 12 8.2 IN-BAND RADIATED SPURIOUS EMISSION MEASUREMENTS...................................................... 13 8.3 RADIATED SPURIOUS EMISSION MEASUREMENTS, OUT-OF-BAND .......................................... 14 9.0 CONCLUSION................................................................................................................................16 FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 2 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

MEASUREMENT REPORT FCC Part 15.225 § 2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 6660-B Dobbin Road, Columbia, MD 21045 USA FCC RULE PART(S): Part 15 Subpart C (15.225) IC SPECIFICATION(S): RSS-210 Issue 8 MODEL: E971, LGE971, LG-E971 FCC ID: ZNFE971 Test Device Serial No.: 207KPBF000229 Production Pre-Production Engineering FCC CLASSIFICATION: Low Power Communications Device Transmitter (DXX) DATE(S) OF TEST: October 02, 2012 TEST REPORT S/N: 0Y1209201382.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21045, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 90864) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451A-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451A-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 3 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 PCTEST Test Location The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility in New Concept Business Park, Guilford Industrial Park, Columbia, Maryland. The site address is 6660-B Dobbin Road, Columbia, MD 21045. The test site is one of the highest points in the Columbia area with an elevation of 390 feet above mean sea level. The site coordinates are 39o 11’15” N latitude and 76o 49’38” W longitude. The facility is 1.5 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. There are no FM or TV transmitters within 15 miles of the site. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4- 2009 on January 10, 2012. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 4 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFE971. The test data contained in this report pertains only to the emissions due to the RFID transmitter of the EUT. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 GSM/GPRS/EDGE, 850/1900 WCDMA, Band 7, 17 LTE, 802.11a/b/g/n WLAN (DTS/NII), Bluetooth (1x,EDR, LE), NFC 2.3 Test Configuration The LG Model: E971, LGE971, LG-E971, FCC ID: ZNFE971 was set to continuously transmit at 13.56MHz. This was performed using manufacturer software loaded on the phone to allow for continuous transmission. This device was tested in accordance with the guidance of ANSI C63.4- 2009. See Section 3.2 radiated emissions test setup. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. 2.5 Labeling Requirements Per 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name and FCC ID must be displayed on the device per Section 15.19(b)(2). Please see attachment for FCC ID label and label location. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 5 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

3.0 DESCRIPTION OF TEST 3.1 Evaluation Procedure The measurement procedure described in the American National Standard for Methods of Measurement of Radio-Noise Emission from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSI C63.4-2009) was used in the measurement of the LG Portable Handset FCC ID: ZNFE971. Deviation from measurement procedure…………………………………………….....................................None FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 6 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

3.2 Radiated Emissions The radiated test facilities consisted of an indoor semi-anechoic chamber used for exploratory measurements and an open area test site (OATS) used for final measurements. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies higher than the upper frequency range of the broadband antenna used for testing, linearly polarized double ridge horn antennas were used. For frequencies below Figure 3-1. 3-Meter 30MHz, a calibrated loop antenna was used. Test Site Exploratory measurements were performed at 1 meter test distance inside the semi- anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of a 0.8 meter high non-metallic 1 x 1.5 meter table (see Figure 3-3). The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, turntable azimuth, and receive antenna height was noted for each frequency found. To record the exploratory measurements, the analyzers’ detector Figure 3-2. function was set to peak mode and the bandwidth was set to 100kHz. Dimensions of Outdoor Test Site Final measurements were made on the OATS at 3 meter test range using calibrated, linearly polarized broadband or horn antennas (see Figure 3-1). The measurement area is situated on an 18 meter x 20 meter galvanized 1/2" hardware cloth as the conducting ground plane. This material is sewn together in sections 4 feet wide and 60 feet long. A total of eighteen sections are required to cover the entire measurement area. Sections are laid across the width of the pad, overlapped 1" and sewn and soldered together at intervals of 3" (7.6 cm.) The terrain of the test site is reasonably flat and level. Power and cable to the test site are buried 18" deep into the ground outside the perimeter of the site. An all-weather non-metallic housing is situated on a 2 x 3 meter area adjacent to the measurement area to house the test equipment (see Figure 3-2). The test set-up was again placed on top of the same a 0.8 meter high non-metallic 1 x 1.5 meter table on the Figure 3-3. Turntable OATS as used for exploratory measurements in the indoor chamber. The test set-up was and System Setup re-configured to the same setup that was previously determined through exploratory measurements to have produced the worst case emissions. The spectrum analyzer was set to the frequencies found to have caused the highest radiated disturbances with respect to the limit during preliminary radiated measurements. The turntable containing the system was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was re-maximized by varying: the mode of operation or resolution, clock or data exchange speed, scrolling H pattern to the EUT and/or support equipment, powering the monitor from the floor mounted outlet box and the computer aux AC outlet, if applicable, and changing the polarity of the receive antenna, whichever produced the worst-case emissions. To record the final measurements, the analyzer detector function was set to Figure 3-4. CISPR quasi-peak mode and the bandwidth of the spectrum analyzer was set to 100kHz Normalized Site for frequencies below 1GHz or 1MHz for frequencies above 1GHz. For average Attenuation Curves measurements above 1GHz, the analyzer was set to peak detector with a reduced VBW (H&V) setting (RBW = 1MHz, VBW = 10Hz). Each emission reported was calibrated using a signal generator. The Theoretical Normalized Site Attenuation Curves for both horizontal and vertical polarization are shown in Figure 3-4. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 7 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antennas of the LG Portable Handset are permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The LG Portable Handset FCC ID: ZNFE971 unit complies with the requirement of §15.203. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 8 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

5.0 SAMPLE CALCULATIONS 5.1 Radiated Emission Measurement Sample Calculation @ 66.7 MHz Class B limit = 100 V/m = 40.0 dBV/m Reading = - 76.0 dBm (calibrated level) Convert to dbV = - 76.0 + 107 = 31.0 dBV Antenna Factor + Cable Loss = 5.8 dB/m Total = 36.8 dBV/m Margin = 36.8 - 40.0 = - 3.2 dB = 3.2 dB below limit Note: Level [dBV] = 20 log 10 (Level [V/m]) Level [dBV] = Level [dBm] + 107 FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 9 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

6.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number - RE1 Radiated Emissions Cable Set (UHF/EHF) 6/7/2012 Annual 6/7/2013 N/A - RE2 Radiated Emissions Cable Set (VHF/UHF) 2/13/2012 Annual 2/13/2013 N/A Agilent 8447D Broadband Amplifier 5/8/2012 Annual 5/8/2013 1937A03348 Agilent 8449B (1-26.5GHz) Pre-Amplifier 2/15/2012 Annual 2/15/2013 3008A00985 Agilent 85650A Quasi-Peak Adapter 4/4/2012 Annual 4/4/2013 2043A00301 Agilent 8566B (100Hz-22GHz) Spectrum Analyzer 4/4/2012 Annual 4/4/2013 2618A02866 Agilent 8566B (100Hz-22GHz) Spectrum Analyzer 4/4/2012 Annual 4/4/2013 2542A11898 Agilent E4448A PSA (3Hz-50GHz) Spectrum Analyzer 2/15/2012 Annual 2/15/2013 US42510244 Agilent E8257D (250kHz-20GHz) Signal Generator 4/5/2012 Annual 4/5/2013 MY45470194 Agilent N9020A MXA Signal Analyzer 10/10/2011 Annual 10/10/2012 US46470561 Agilent N9030A PXA Signal Analyzer 2/23/2012 Annual 2/23/2013 MY49432391 Agilent N9038A MXE EMI Receiver 8/5/2012 Annual 8/5/2013 MY51210133 Emco 6502 Active Loop Antenna (10k - 30 MHz) 5/31/2012 Biennial 5/31/2014 267 Emco 3816/2 LISN 11/5/2010 Biennial 11/5/2012 9707-1077 Emco 3816/2 LISN 11/3/2010 Biennial 11/3/2012 9707-1079 Schwarzbeck VULB-9161SE Trilog Super Broadband Test Antenna 11/8/2011 Biennial 11/8/2013 9161-4075 Sunol DRH-118 Horn Antenna (1-18 GHz) 6/17/2011 Biennial 6/17/2013 A042511 Table 6-1. Annual Test Equipment Calibration Schedule Note: In the table above, if the equipment calibration due date falls within the test dates, care was taken to ensure that the equipment was utilized prior to the calibration due date. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 10 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

7.0 ENVIRONMENTAL CONDITIONS The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is controlled within the range 86-106kPa (860-1060mbar). FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 11 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

8.0 TEST DATA 8.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFE971 Frequencies Examined: 13.56MHz FCC Part RSS Test Test Test Description Test Limit Reference Section(s) Section(s) Condition Result TRANSMITTER MODE (Tx) 15,848µV/m @ 30m 13.553 – 13.567 MHz 334µV/m @ 30m 15.225 RSS-210 13.410 – 13.553 MHz In-Band Emissions PASS Section 8.2 (a)(b)(c) [A2.6] 13.567 – 13.710 MHz 106µV/m @ 30m RADIATED 13.110 – 13.410 MHz 13.710 – 14.010 MHz Emissions outside of the specified 15.225 (d) RSS-210 band (13.110 – 14.010 MHz) must Out-of-Band Emissions PASS Section 8.3 15.209 [A2.6] meet the radiated limits detailed in 15.209 Table 8-1. Summary of Test Results FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 12 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

8.2 In-Band Radiated Spurious Emission Measurements §15.225(a), (b), (c); RSS-210 [A2.6] Radiated emission testing was performed in the band 13.110 – 14.010 MHz. Frequency: 13.56MHz Measurement Distance: 3 Meters EUT 3m Field 30m Field Frequency Level AFCL Antenna Limit Margin Pol. Strength Strength [MHz] [dBm] [dB/m] Position [dBV/m] [dB] [H/V] [dBV/m] [dBV/m] 13.194 -93.32 10.20 X H 23.88 -16.12 40.51 -56.63 13.306 -92.78 10.20 X H 24.42 -15.58 40.51 -56.09 13.381 -92.77 10.19 X H 24.42 -15.58 40.51 -56.08 13.560 -87.92 10.19 X H 29.27 -10.73 84.00 -94.73 13.632 -93.03 10.19 X H 24.16 -15.84 50.47 -66.32 13.712 -92.94 10.18 X H 24.24 -15.76 40.51 -56.26 13.846 -93.27 10.18 X H 23.91 -16.09 40.51 -56.59 Table 8-2. In-Band Radiated Measurements NOTES: 1. All measurements were performed using a loop antenna. The antenna was positioned in three orthogonal positions (X front, Y side, Z top) and the position with the highest emission level was recorded. 2. The EUT was positioned in three orthogonal planes to determine the orientation resulting in the worst case emissions. 3. Measurements were performed at 3m and the data was extrapolated to the specified measurement distance of 30m using the square of an inverse linear distance extrapolation factor (40 dB/decade) as specified in §15.31(f)(2). Extrapolation Factor = 20 log10(30/3)2 = 40dB 4. All measurements were recorded using a spectrum analyzer employing a quasi-peak detector. 5. Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] 6. AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] 7. Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 13 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

8.3 Radiated Spurious Emission Measurements, Out-of-Band §15.209, §15.225(d); RSS-210 [A2.6] The EUT was tested from 9kHz up to the 1GHz excluding the band 13.110 – 14.010 MHz. All measurements up to 960MHz were recorded with a spectrum analyzer employing a quasi-peak detector. All out-of-band emissions must not exceed the limits shown in Table 8-3 per Section 15.209. A loop antenna was used to investigate emissions below 30MHz. Field Strength Measured Distance Frequency [V/m] [Meters] 0.009 – 0.490 MHz 2400/F (kHz) 300 0.490 – 1.705 MHz 24000/F (kHz) 30 1.705 – 30.00 MHz 30 30 30.00 – 88.00 MHz 100 3 88.00 – 216.0 MHz 150 3 216.0 – 960.0 MHz 200 3 Above 960.0 MHz 500 3 Table 8-3. Radiated Limits – Out of band Sample Calculation o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB] o Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m] FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 14 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

Radiated Spurious Emission Measurements, Out-of-Band (Cont’d) §15.209, §15.225(d); RSS-210 [A2.6] Tx Frequency 13.56MHz Measurement Distance: 3 Meters 3m Field Frequency Level AFCL Pol Limit Margin Strength [MHz] [dBm] [dB/m] [H/V] [dBV/m] [dB] [dBV/m] 33.40 -94.88 11.66 V 23.79 40.00 -16.21 34.93 -94.87 12.04 V 24.17 40.00 -15.83 38.67 -90.96 12.76 V 28.80 40.00 -11.20 41.56 -91.48 13.10 V 28.62 40.00 -11.38 59.16 -99.76 13.86 H 21.10 40.00 -18.90 73.88 -91.65 8.11 H 23.47 40.00 -16.53 Table 8-4. Radiated Measurements NOTES: 1. All measurements were recorded using a spectrum analyzer employing a quasi-peak detector for emissions below 960MHz. 2. Both Vertical and Horizontal polarities of the receive antenna were evaluated with the worst case emissions being reported. Below 30MHz the loop antenna was positioned in 3 orthogonal planes (X front, Y side, Z top) to determine the orientation resulting in the worst case emissions. 3. The EUT was positioned in three orthogonal planes to determine the orientation resulting in the worst case emissions. 4. The EUT is supplied with nominal AC voltage and/or a new/fully-recharged battery. 5. The spectrum is measured from 9kHz to the 10th harmonic and the worst-case emissions are reported. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 15 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012

9.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFE971 has been tested to show compliance with the requirements specified in §15.225 of the FCC Rules and RSS-210 of the Industry Canada rules. FCC Pt. 15.225 MEASUREMENT REPORT Reviewed by: FCC ID: ZNFE971 (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 16 of 16 0Y1209201382.ZNF October 02, 2012 Portable Handset © 2012 PCTEST Engineering Laboratory, Inc. REV 2.4RFFI 05/17/2012


Document Created: 2019-10-17 08:26:48
Document Modified: 2019-10-17 08:26:48
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC