Test Report 2

FCC ID: ZNFE450F

Test Report

Download: PDF
FCCID_1898915

Report Number: F690501/RF-RTL006169-2 Page: 42 of 67 3. 6 ໒ Bandwidth Measurement 3.1. Test Setup EUT Attenuator Spectrum Analyzer 3.2. Limit According to §15.247(a)(2), systems using digital modulation techniques may operate in the 902 ~928 ໬, 2 400 ~ 2 483.5 ໬, and 5 725 ~ 5 825 ໬ bands. The minimum of 6 ໒ Bandwidth shall be at least 500 ໫ 3.3. Test Procedure All data rates and modes were investigated for this test. The full data for the worst case data rate are reported in this section. The test follows section 7.1 of FCC KDB Publication 558074 1. Set resolution bandwidth (RBW) = 1 – 5 % of DTS BW, not to exceed 100 ໫ 2. Set the video bandwidth (VBW) ˻ 3 ዖ͑ RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude point (upper and lower) that are attenuated by 6 ໒G relative to the maximum level measured in the fundamental emission. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 43 of 67 3.4. Test Results Ambient temperature : (23 ρ͑ 2) ୅ Relative humidity : 47 % R.H. Channel Data Rate 6 ༐ Bandwidth Operation Mode Channel Frequency (Mbps) (໬) (໬) Low 2 412 ໬ 9.55 DSSS 1 Middle 2 437 ໬ 9.60 (802.11b) High 2 462 ໬ 9.55 Low 2 412 ໬ 16.40 OFDM 6 Middle 2 437 ໬ 16.45 (802.11g) High 2 462 ໬ 16.45 Low 2 412 ໬ 17.50 OFDM MCS0 Middle 2 437 ໬ 17.65 (802.11n_HT20) High 2 462 ໬ 17.60 Low 2 422 ໬ 34.70 OFDM MCS0 Middle 2 437 ໬ 36.10 (802.11n_HT40) High 2 452 ໬ 35.00 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 44 of 67 DSSS : 802.11b Low Channel Middle Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 45 of 67 High Channel OFDM : 802.11g Low Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 46 of 67 Middle Channel High Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 47 of 67 OFDM : 802.11n_HT20 Low Channel Middle Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 48 of 67 High Channel OFDM : 802.11n_HT40 Low Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 49 of 67 Middle Channel High Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 50 of 67 4. Maximum Peak Output Power Measurement 4.1. Test Setup G EUT Attenuator Power sensor Power meter 4.2. Limit According to §15.247(b)(3), for systems using digital modulation in the 902 ~ 928 ໬, 2 400 ~2 483.5 ໬, and 5 725 ~ 5 850 ໬ band: 1 Watt. As an alternative to a peak power measurement, compliance with the one watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antenna elements. The average must not include any intervals during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode. According to §15.247(b)(4), the conducted output power limit specified in paragraph(b) of this section is based on the use of antenna with directional gains that do not exceed 6 ໒i. Except as shown in paragraph(c) of this section, if transmitting antenna of directional gain greater than 6 ໒i are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraph (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in ໒ that the directional gain of the antenna exceeds 6໒i. 4.3. Test Procedure - Peak and average power meter method. All data rates and modes were investigated for this test. The full data for the worst case data rate are reported in this section. The test follows section 8.1.3 & 8.2.3 of FCC KDB Publication 558074 -The maximum peak conducted output power can be measured using a broad band peak RF power meter. The power meter must have a video bandwidth that is greater than or equal to the DTS bandwidth and shall utilize a fast, average-responding diode type sensor. -This procedure provides an alternative for determining the RMS output power using a broadband RF average power meter with a thermocouple detector if the EUT can be configured to transmit continuously or if the power meter can be triggered/signal-gated such that the power is measured only when the EUT is transmitting at its maximum power control level. 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the Power sensor (Nominal VBW is 50 ໬). 3. Measure peak & average power each channel. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 51 of 67 4.4. Test Results Ambient temperature : (23 ρ͑ 2) ୅ Relative humidity : 47 % R.H. Channel Attenuator + Average Data Rate Peak Power Mode Channel Frequency Cable offset power (Mbps) Result (໒ m) (໬) (໒) Result (໒ mP 1 15.21 19.17 2 15.10 18.94 Low 2 412 10.90 5.5 15.16 18.68 11 14.94 18.81 1 15.90 19.54 DSSS 2 15.76 19.49 Middle 2 437 10.90 (802.11b) 5.5 15.65 19.08 11 15.54 19.18 1 16.00 19.63 2 16.34 20.00 High 2 462 10.91 5.5 16.10 19.62 11 15.62 19.22 6 12.13 24.36 9 12.01 24.37 12 11.91 24.25 18 11.71 24.35 Low 2 412 10.90 24 11.54 24.50 36 11.23 24.37 48 10.96 24.48 54 10.85 24.35 6 12.25 24.59 9 12.11 24.55 12 12.01 24.38 OFDM 18 11.82 24.39 Middle 2 437 10.90 (802.11g) 24 11.61 24.62 36 11.33 24.60 48 11.04 24.59 54 10.95 24.55 6 12.43 24.67 9 12.28 24.69 12 12.18 24.62 18 11.98 24.60 High 2 462 10.91 24 11.79 24.91 36 11.50 24.89 48 11.20 24.70 54 11.11 24.75 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 52 of 67 Channel Attenuator + Average Data rate Peak Power Mode Channel Frequency Cable offset power (Mbps) Result (໒ m) (໬) (໒) Result (໒ ”P MCS0 10.32 22.10 MCS1 10.10 21.85 MCS2 10.33 22.49 MCS3 10.14 23.14 Low 2 412 10.90 MCS4 9.86 22.59 MCS5 9.61 22.62 MCS6 9.10 22.05 MCS7 8.40 21.86 MCS0 10.84 22.63 MCS1 10.61 22.60 MCS2 10.42 22.43 OFDM MCS3 10.24 23.19 Middle 2 437 10.90 (802.11n_HT20) MCS4 9.95 22.47 MCS5 9.68 22.79 MCS6 9.13 23.09 MCS7 8.99 22.12 MCS0 10.94 22.73 MCS1 10.73 22.38 MCS2 10.53 22.28 MCS3 10.33 22.44 High 2 462 10.91 MCS4 10.04 22.48 MCS5 9.78 22.78 MCS6 9.70 22.66 MCS7 9.57 22.52 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 53 of 67 Channel Attenuator + Average Data rate Peak Power Mode Channel Frequency Cable offset power (Mbps) Result (໒ m) (໬) (໒) Result (໒ ”P MCS0 9.75 22.42 MCS1 9.70 21.91 MCS2 9.38 22.10 MCS3 9.11 21.84 Low 2 422 10.90 MCS4 8.66 22.03 MCS5 8.20 22.00 MCS6 8.38 22.31 MCS7 8.22 22.35 MCS0 10.35 22.89 MCS1 9.95 22.24 MCS2 10.05 22.91 OFDM MCS3 9.35 22.88 Middle 2 437 10.90 (802.11n_HT40) MCS4 8.88 22.44 MCS5 9.03 22.73 MCS6 8.58 22.88 MCS7 8.44 22.48 MCS0 10.67 23.18 MCS1 10.30 23.04 MCS2 10.26 22.98 MCS3 10.01 22.91 High 2 452 10.91 MCS4 9.60 22.90 MCS5 9.25 22.98 MCS6 8.82 22.93 MCS7 8.70 22.63 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 54 of 67 5. Power Spectral Density Measurement 5.1. Test Setup G EUT Attenuator Spectrum Analyzer 5.2. Limit §15.247(e) For digitally modulated system, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 ໒ m in any 3 ໫ band any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. 5.3. Test Procedure All data rates and modes were investigated for this test. The full data for the worst case data rate are reported in this section. The measurements are recorded using the AVGPSD measurement procedure in section 9.2 of KDB 558074. 1. Use this procedure when the maximum conducted output power in the fundamental emission is used to demonstrate compliance. The EUT must be configured to transmit continuously at full power over the measurement duration. 2. Set the analyzer span to at least 1.5 times the DTS channel bandwidth. 3. Set the RBW ˻ 3 ໫ 4. Set the VBW ˻ 3 ዖ RBW 5. Detector = power average (RMS) or sample detector (when RMS not available). 6. Ensure that the number of measurement points in the sweep  2 ዖ span/RBW 7. Sweep time = auto couple. 8. Employ trace averaging (RMS) mode over a minimum of 100 traces. 9. Use the peak marker function to determine the maximum amplitude level. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 55 of 67 5.4. Test Results Ambient temperature : (23 ρ͑ 2) ୅ Relative humidity : 47 % R.H. Operation Data Rate Measured PSD Maximum Limit Channel Frequency Mode (Mbps) (໒ m) (໒ m) Low 2 412 ໬ -12.73 8 DSSS 1 Middle 2 437 ໬ -12.07 8 (802.11b) High 2 462 ໬ -11.97 8 Low 2 412 ໬ -18.69 8 OFDM 6 Middle 2 437 ໬ -18.76 8 (802.11g) High 2 462 ໬ -17.82 8 Low 2 412 ໬ -20.31 8 OFDM MCS0 Middle 2 437 ໬ -19.46 8 (802.11n_HT20) High 2 462 ໬ -19.78 8 Low 2 422 ໬ -21.94 8 OFDM MCS0 Middle 2 437 ໬ -21.66 8 (802.11n_HT40) High 2 452 ໬ -20.76 8 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 56 of 67 DSSS : 802.11b Low Channel Middle Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 57 of 67 High Channel OFDM : 802.11g Low Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 58 of 67 Middle Channel High Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 59 of 67 OFDM : 802.11n_HT20 Low Channel Middle Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 60 of 67 High Channel OFDM : 802.11n_HT40 Low Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 61 of 67 Middle Channel High Channel The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 62 of 67 6. Transmitter AC Power Line Conducted Emission 6.1. Test Setup Shield room enclosure Main power source 0.4m LISN AC Adaptor Table height 0.8m EUT to Test Receiver 6.2. Limit According to §15.207(a) for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 ໫ to 30 ໬, shall not exceed the limits in the following table, as measured using a 50 uH/50 ohm line impedance stabilization network(LISN). Compliance with the provision of this paragraph shall on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower applies at the boundary between the frequency ranges. Conducted limit (໒໛) Frequency of Emission (໬) Quasi-peak Average 0.15 – 0.50 66 - 56* 56 - 46* 0.50 – 5.00 56 46 5.00 – 30.0 60 50 * Decreases with the logarithm of the frequency. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 63 of 67 6.3. Test Procedures All data rates and modes were investigated for this test. The full data for the worst case data rate are reported in this section. AC line conducted emissions from the EUT were measured according to the dictates of ANSI C63.4-2003 1. The test procedure is performed in a 6.5m × 3.6m× 3.6m (L × W × H) shielded room. The EUT along with its peripherals were placed on a 1.0 m(W)× 1.5 m(L) and 0.8 m in height wooden table and the EUT was adjusted to maintain a 0.4 meter space from a vertical reference plane. 2. The EUT was connected to power mains through a line impedance stabilization network (LISN) which provides 50 ohm coupling impedance for measuring instrument and the chassis ground was bounded to the horizontal ground plane of shielded room. 3. The excess power cable between the EUT and the LISN was bundled. All connecting cables of EUT were moved to find the maximum emission. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 64 of 67 6.4. Test Results (Worst case configuration_11b mode, 1 Mbps, middle channel) The following table shows the highest levels of conducted emissions on both phase of Hot and Neutral line. Ambient temperature : (23 ρ͑ 2) ୅ Relative humidity : 47 % R.H. Frequency range : 0.15 Ꮎ – 30 Ꮎ Measured Bandwidth : 9 ໫ FREQ. LEVEL(ᎤᎭ) LIMIT(໒໛) MARGIN(໒) LINE (໬) Q-Peak Average Q-Peak Average Q-Peak Average 0.19 32.77 20.27 N 64.26 54.26 31.49 33.99 0.34 32.78 24.88 N 59.20 49.20 26.42 24.32 0.54 21.39 11.89 N 56.00 46.00 34.61 34.11 1.48 22.84 14.04 N 56.00 46.00 33.16 31.96 4.80 18.29 10.39 N 56.00 46.00 37.71 35.61 25.06 30.63 25.83 N 60.00 50.00 29.37 24.17 0.34 36.50 34.00 H 59.33 49.33 22.83 15.33 0.40 26.90 17.60 H 57.85 47.85 30.95 30.25 0.55 26.91 22.11 H 56.00 46.00 29.09 23.89 0.76 26.03 19.93 H 56.00 46.00 29.97 26.07 1.18 25.45 17.05 H 56.00 46.00 30.55 28.95 25.06 24.41 22.71 H 60.00 50.00 35.59 27.29 Note ; 1. Line ( H ): Hot, Line ( N ): Neutral 2. All modes of operation were investigated and the worst-case emissions are reported using 11b_1Mbps 3. The limit for Class B device(s) from 150 Ꮍ to 30 Ꮎ are specified in Section of the Title 47 CFR. 4. Traces shown in plot mad using a peak detector and average detector 5. Deviations to the Specifications: None. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 65 of 67 Plots of Conducted Power line Test mode : (Neutral) Level [dBμV] 100 80 60 40 20 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 66 of 67 Test mode : (Hot) Level [dBμV] 100 80 60 40 20 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea

Report Number: F690501/RF-RTL006169-2 Page: 67 of 67 7. Antenna Requirement 7.1. Standard Applicable For intentional device, according to FCC 47 CFR Section §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section §15.247 (b) if transmitting antennas of directional gain greater than 6 ໒ i are used, the power shall be reduced by the amount in ໒ that the gain of the antenna exceeds 6 ໒ i. 7.2. Antenna Connected Construction Antenna used in this product is Internal type(PIFA) with gain of 0.7 ໒ i. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS KoreaCo., Ltd. (GunpoLaboratory) 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.ee.sgs.com/korea


Document Created: 2013-02-13 12:07:32
Document Modified: 2013-02-13 12:07:32
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC