modular approval letter

FCC ID: ZMONL668LA

Cover Letter(s)

Download: PDF

FCCID_4322522

Modular Approval Request FCC FCC ID: _ZMONL668LA

Items to be covered Answer from applicant
1. The modular transmitter must have its own RF shielding. Y
The EUT provides the

M
RF shielding. See EUT
photo.
2. The modular transmitter must have buffered modulation/data inputs (if such inputs Y
are provided) to ensure that the module will comply with Part 15 requirements The EUT has its buffered

CO
under conditions of excessive data rates or over-modulation.
modulation.
3. The modular transmitter must have its own power supply regulation. Y
The EUT has its own
power supply regulation,
please see the Schematic
Diagram.
4. The modular transmitter must comply with the antenna requirements of Section Y
15.203 and 15.204(c). The antenna must either be permanently attached or employ The EUT meets the FCC
BO
a “unique” antenna coupler (at all connections between the module and the antenna,
including the cable)..
antenna requirements;
unique antenna
connector and photo of
antenna are shown in the
test report.
5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Y
module must not be inside another device during testing. This is intended to The EUT was tested with
demonstrate that the module is capable of complying with Part 15 emission limits
a test board, Please see
FI
regardless of the device into which it is eventually installed.
test report and setup
photo
6. The modular transmitter must be labeled with its own FCC ID number, and, if the Y
FCC ID is not visible when the module is installed inside another device, then the The FCC ID is
outside of the device into which the module is installed must also display a label ZMONL668LA
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains
FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning
may be used. The Grantee may either provide such a label, an example of which
must be included in the application for equipment authorization, or, must provide
adequate instructions along with the module which explain this requirement. In the
latter case, a copy of these instructions must be included in the application for
equipment authorization.

7. The modular transmitter must comply with any specific rule or operating Y
requirements applicable to the transmitter and the manufacturer must provide The EUT is compliant
adequate instructions along with the module to explain any such requirements. A
copy of these instructions must be included in the application for equipment
with all applicable FCC
authorization. For example, there are very strict operational and timing rules. Details
requirements that must be met before a transmitter is authorized for operation under instructions for
Section 15.231. For instance, data transmission is prohibited, except for operation maintaining compliance
under Section 15.231(e), in which case there are separate field strength level and are give in the User
timing requirements. Compliance with these requirements must be assured.
Manual.
8. The modular transmitter must comply with any applicable RF exposure Y
requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific The EUT complies with
Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g),
require that Unlicensed PCS, UNII and millimeter wave devices perform routine
RF exposure
environmental evaluation for RF Exposure to demonstrate compliance. In requirement.
addition, spread spectrum transmitters operating under Section 15.247 are
required to address RF Exposure compliance in accordance with Section
15.247(b)(4). Modular transmitters approved under other Sections of Part 15,
when necessary, may also need to address certain RF Exposure concerns,

Document Created: 2019-06-14 10:22:44
Document Modified: 2019-06-14 10:22:44

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC