FCC Modular Approval Request

FCC ID: ZMOM910GL

Cover Letter(s)

Download: PDF
FCCID_3959202

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: _ZMOM910GL_ Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, the EUT has RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Yes, the EUT has its buffered are provided) to ensure that the module will comply with Part 15 requirements modulation. under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. Yes, the EUT has its own power supply regulation,U600 is the PMU PMD9607.It supply 14 LDOS and 4 buck circuit 4. The modular transmitter must comply with the antenna requirements of Section Yes, the EUT meets the FCC 15.203 and 15.204(c). The antenna must either be permanently attached or employ antenna requirements; unique a “unique” antenna coupler (at all connections between the module and the antenna, antenna connector and photo including the cable).. of antenna are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Yes, the EUT was tested with module must not be inside another device during testing. This is intended to a test board, Please see test demonstrate that the module is capable of complying with Part 15 emission limits report and setup photo regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the Yes, please see exhibition FCC ID is not visible when the module is installed inside another device, then the label sample for the FCC ID outside of the device into which the module is installed must also display a label of this module. And also in referring to the enclosed module. This exterior label can use wording such as the the exhibition Users manual, following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains there are instructions deliver FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning to the OEM on how to label may be used. The Grantee may either provide such a label, an example of which the end product. must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating Yes, the EUT is compliant requirements applicable to the transmitter and the manufacturer must provide with all applicable FCC rules. adequate instructions along with the module to explain any such requirements. A Details instructions for copy of these instructions must be included in the application for equipment maintaining compliance are authorization. For example, there are very strict operational and timing given in the User Manual. requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure Yes, the EUT complies with requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific RF exposure requirement. Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA).

RF_734_00, Issue 1 Name and surname of applicant (or authorized representative): Yin Jixiong Date: 2018-07-24 Signature:


Document Created: 2018-08-07 20:44:06
Document Modified: 2018-08-07 20:44:06
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC