Modular Approval Letter

FCC ID: ZMOL860GLD

Cover Letter(s)

Download: PDF
FCCID_4253976

Fibocom Wireless Inc. 5/F, Tower A, Technology Building II, 1057 Nanhai Blvd, Nanshan, Shenzhen, China 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: ZMOL860GLD Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. Y The EUT provides the RF shielding. See EUT photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Y are provided) to ensure that the module will comply with Part 15 requirements The EUT has its buffered under conditions of excessive data rates or over-modulation. modulation. 3. The modular transmitter must have its own power supply regulation. Y The EUT has its own power supply regulation, please see the Schematic Diagram. 4. The modular transmitter must comply with the antenna requirements of Section Y 15.203 and 15.204(b)(c). The antenna must either be permanently attached or The EUT meets the FCC employ a “unique” antenna coupler (at all connections between the module and the antenna requirements; unique antenna, including the cable). antenna connector and photo of antenna are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Y module must not be inside another device during testing. This is intended to The EUT was tested with a test demonstrate that the module is capable of complying with Part 15 emission limits board, Please see test report regardless of the device into which it is eventually installed. and setup photo 6. The modular transmitter must be equipped with either a permanently affixed label Y or must be capable of electronically displaying its FCC identification number in The FCC ID is ZMOL860GLD accordance with 15.212 (a)(1)(vi)(A) / (B). 7. The modular transmitter must comply with any specific rule or operating Y requirements applicable to the transmitter and the manufacturer must provide The EUT is compliant with all adequate instructions along with the module to explain any such requirements. A applicable FCC rules. Details copy of these instructions must be included in the application for equipment instructions for maintaining authorization. For example, there are very strict operational and timing compliance are give in the User requirements that must be met before a transmitter is authorized for operation under Manual. Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure Y requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and The EUT complies with RF specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and exposure requirement. 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance.

Fibocom Wireless Inc. 5/F, Tower A, Technology Building II, 1057 Nanhai Blvd, Nanshan, Shenzhen, China 04 April 16 ___________________________________ XueShan Huang / Certification Engineer Fibocom Wireless Inc. Tel.: +86-755-26525092 E-mail: keith.huang@fibocom.com


Document Created: 2019-04-24 11:20:18
Document Modified: 2019-04-24 11:20:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC