FCC Modular Approval Request

FCC ID: ZMOL860GL

Cover Letter(s)

Download: PDF
FCCID_4211190

RF_734_00, Issue 1 Limited Modular Approval Request FCC (per DA 00-1407) FCC ID: _ZMOL860GL_ Items to be covered by Limited modular transmitters Answer from applicant 1. The modular transmitter must have its own RF shielding. Y The EUT provides the RF shielding. See EUT photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs Y are provided) to ensure that the module will comply with Part 15 requirements The EUT has its buffered under conditions of excessive data rates or over-modulation. modulation. 3. The modular transmitter must have its own power supply regulation. Y The EUT has its own power supply regulation, please see the Schematic Diagram. 4. The modular transmitter must comply with the antenna requirements of Section Y 15.203 and 15.204(c). The antenna must either be permanently attached or employ The EUT meets the FCC a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. antenna requirements; unique antenna connector and photo of antenna are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Y module must not be inside another device during testing. This is intended to The EUT was tested with demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. a test board, Please see test report and setup photo 6. The modular transmitter must be labeled with its own FCC ID number, and, if the Y FCC ID is not visible when the module is installed inside another device, then the please see exhibition label outside of the device into which the module is installed must also display a label sample for the FCC ID of referring to the enclosed module. This exterior label can use wording such as the this module. And also in the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains exhibition Users manual, FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning there are instructions may be used. The Grantee may either provide such a label, an example of which deliver to the OEM on how must be included in the application for equipment authorization, or, must provide to label the end product. adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating Y requirements applicable to the transmitter and the manufacturer must provide The EUT is compliant adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment with all applicable FCC authorization. For example, there are very strict operational and timing rules. Details requirements that must be met before a transmitter is authorized for operation under instructions for Section 15.231. For instance, data transmission is prohibited, except for operation maintaining compliance under Section 15.231(e), in which case there are separate field strength level and are give in the User timing requirements. Compliance with these requirements must be assured. Manual. 8. The modular transmitter must comply with any applicable RF exposure Y requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific The EUT complies with Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine RF exposure environmental evaluation for RF Exposure to demonstrate compliance. In requirement. addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns,

RF_734_00, Issue 1 typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): _XueShan Huang_ Date:2019-03-20 Signature:


Document Created: 2019-04-04 08:43:30
Document Modified: 2019-04-04 08:43:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC