Calibration report part 3

FCC ID: ZMOL850GL

RF Exposure Info

Download: PDF
FCCID_4014815

U m TTL in Collaboration with Add: No.51 Xueyuan Road, Haidian Distrct, Beijing, 100191, China Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: cttl@chinatt.com hitpywwwchinattL.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear(frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «_ Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. « Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. + Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned underthe liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. «_ Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. & SAR measured: SAR measured at the stated antenna input power. «_ SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z17—97036 Page 2 of 8

U m___________________ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: etl@chinatt.com hitps/wwscchinattlen Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.0.8.1258 Extrapolation Advanced Extapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz+ 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £0.2) °C 39.0 £6 % 1.77 mhoim + 6 % Head TSL temperature change during test «10 °C ~— ~—— SAR result with Head TSL SAR averaged over 1_cm"_(1 g) of Head TSL Condition SAR measured 250 mW input power 13.0 mW /g SAR for nominal Head TSL parameters normalized to 1W 52.4 mW 1 £ 20.8 % (k=2) SAR averaged over 10 cm" (10 g) of Head TSL Condition SAR measured 250 mW input power 6.04 mW /g SAR for nominal Head TSL parameters normalized to 1W 24.3 mW ig £ 20.4 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 220 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.020.2) °C 52346 % 1.93 mhoim £ 6 % Body TSL temperature change during test «10 °C s« m SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 12.6 mW /g SAR for nominal Body TSL parameters normalized to 1W 50.5 mW / + 20.8 % (k=2) SAR averaged over 10 Cm" (10 g) of Body TSL Condition SAR measured 250 mW input power 5.82 mW /g SAR for nominal Body TSL parameters normalized to 1W 23.3 mW 1g 4 20.4 % (k=2) Certificate No: Z17—97036 Page 3 of 8

:@@h_ TTL in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.00+ 5.940 Retur Loss ~24.30B Antenna Parameters with Body TSL Impedance, transformed to feed point 48.70+ 6.25]0 Return Loss —23.80B General Antenna Parameters and Design Electrical Delay (one direction) 1.257 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97036 Page 4 of 8

U omm___________________ TT[‘/ in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp:/wwwchinattl.en DASYS Validation Report for Head TSL Date: 03.21.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 952 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: f= 2450 MHz; 0 = 1.768 S/m; er = 39.02; p = 1000 kg/m3 Phantom section: Right Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASYS Configuration: * Probe: EX3DV4 — SN3617; ConvF(7.74, 7.74, 7.74); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) «+ Electronics: DAE4 Sn777; Calibrated: $/22/2016 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=Smm Reference Value = 104.6 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 27.0 W/kg SAR(I g) = 13 W/kg; SAR(10 g) = 6.04 W/kg Maximum value of SAR (measured) =21.7 W/kg d8 0 ~4.42 —8.84 13.26 —17.68 2210 E: 0 dB =21.7 W/kg = 13.36 dBW/kg Certificate No: Z17—97036 Page5 of 8

U omm__________________ TTL a s p_e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp=//wwwchinattl.en Impedance Measurement Plot for Head TSL Ti siT Log ag 10. oode/ ner 0.000d8 [F1] 5+99 r5t—2.3300000 one <24. 268 do £0.00 30. co 20. 0o 10.00 0. coop « —10. 00 * —20. 00 ~30.00 ~40. 00 ~50, 00 A IMIRRM S11 snith (R+JX) Scale 10000 [F1 oel] »1 24500000 anz 51.964 n 5.9372 o. 305. Certificate No: 17—97036 Page 6 of 8

U oo____________________ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinatl.com hitp=//wwwchinatt.en DASY5 Validation Report for Body TSL Date: 03.21.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 952 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: {= 2450 MHz; 0 = 1.931 S/m; s, = 52.27; p= 1000 kg/m‘ Phantom section: Center Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS Configuration: + Probe: EX3DV4 — SN3617; ConvF(7.8, 7.8, 7.8); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn777; Calibrated: 8/22/2016 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=Smm Reference Value = 96.07 V/m; Power Drift =—0.04 dB Peak SAR (extrapolated) = 26.4 W/kg SAR(I g) = 12.6 W/kg; SAR(10 g) = 5.82 W/kg Maximum value of SAR (measured) = 20.9 W/kg ~4.41 —8.82 13.22 17.63 —22.04 5 i 0 dB =20.9 W/kg = 13.20 dBW/kg Certificate No: Z17—97036 Page 7 of8

Report No.: BL-SZ1870481-701

Report No.: BL-SZ1870481-701 F.8 2600 MHz Dipole

'@é‘_— iinas «9099 Calibration Laboratory of $¥ Schweizerischer Kalibrierdienst Schml_d & Partner % Service suisse d‘étalonnage Engineering AG Lo Servizio svizzero i taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ?/,,/l/,—\\\ Swiss Calibration Service frlitds Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreament for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 0) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connectorto the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certficate No: D2600V2—1095_Jult7 Page 2 of 8

:@@h_é Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2600 MHz * 1 MHz Head TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.96 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 87.2 26 % 2.04 mho/m + 6 % Head TSL temperature change during test <0.5 °C lied lassd SAR result with Head TSL SAR averaged over1 em‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 14.5 Wkg SAR for nominal Head TSL parameters normalized to 1W 56.4 Wikg 2 17.0 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL condition SAR measured 250 mW input power 6.40 Wikg SAR for nominal Head TSL parameters normalized to 1W 25.2 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.5 2.16 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 51.6 + 6 % 2.22 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— —~— SAR result with Body TSL SAR averaged over 1 m‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 13.8 Wikg SAR for nominal Body TSL parameters normalized to 1W 54.3 W/kg 2 17.0 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 250 mW input power 6.15 Wikg SAR for nominal Body TSL parameters normalized to 1W 24.4 Wikg 2 16.5 % (k=2) Certificate No: D2600V2—1095_Jul17 Page 3 of 8

:%n_—_J Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 472 0 —7.4jo Return Loss —21.9 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 44.6 0 — 5.9 jn Return Loss —21.5 0B General Antenna Parameters and Design [ Electrical Delay (one direction) 1.150 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Thedipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions® paragraph. The SAR data are not affected by this change. The overall dipole length is stil according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 12, 2016 Certiicate No: D2600V2—1095_Jul17 Page 4 of 8

C mm DASY5 Validation Report for Head TSL Date: 10.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1095 Communication System: UID 0 — CW:; Frequency: 2600 MHz Medium parameters used: f= 2600 MHz; 0 = 2.04 $/m; £, = 37.2; p = 1000 kg/m‘ Phantomsection: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.96, 7.96, 7.96); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronies: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom5.0 (front); Type: QD 000 PSO AA: Serial: 1001 * DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=Smm, dz=5mm Reference Value = 114.1 V/m; Power Drift —0.08 dB Peak SAR (extrapolated) = 31.2 W/kg SAR(I g) = 14.5 W/kg; SAR(1O g) = 6.4 W/kg Maximum value of SAR (measured) = 24.2 W/ke 5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 24.2 W/kg = 13.84 dBW/kg Gertficate No: D2600V2—1095_Jul17 Page 5 of 8

C mm ____________ Impedance Measurement Plot for Head TSL 10 Jul zoi i4:30i14 CHZ sar a ucrs m47A700 —7.3535a ©.9244 pF 2 600.000 000 maz Del ca ; o fvg 16" Hia cn2e sir Los 5 d8/REF —20 ce m—21.851 ds _2 £00.000 000 Mkz Ca Hig start 2 400,000 008 Niz Stor 2 200.000 000 hiz Certficate No: D2600V2—1095_Jult7 Page 6 of 8

C en DASY5 Validation Report for Body TSL Date: 10.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; ‘ype: D2600V2; Serial: D2600V2 — SN:1095 Communication System: UID0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz: 0 = S$/m; & = 51.6; p = 1000 kg/m‘ Phantomsection: Flat Section Mcasurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.94, 7.94, 7.94); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom5.0 (back); Type: QD 000 P50 AA; Serial: 1002 * DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 103.9 V/m; Power Drift —0.04 dB Peak SAR (extrapolated) = 28.9 W/kg SAR(I g) = 13.8 W/kg; SAR(10g) = 6.15 W/kg Maximumvalue of SAR (measured) =22.1 W/kg dB 0 ~4.00 —12.00 —16.00 —20.00 0 dB = 22.1 W/kg = 13.44 dBW/kg Certificate No: D2600V2—1095_Jul17 Page 7 of 8

Report No.: BL-SZ1870481-701

U m 2 Add: No.51 Xueyuan Road, Haidian District. Beijing, 100191, China %,/R CAUBRATION Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 '/,,m\“\ CNAS LO570 E—mail: ettl@chinatt.com hitpywwwchinattl.en Client baluntek Certificate No: 2Z17—97083 TIFICATE _____. * es es s Object D5GHzV2 — SN: 1200 Calibration Procedure(s) FD—Z11—003—01 Calibration Procedures fordipole validation kits Calibration date: June 29, 2017 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(2223)C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 22—Sep—16 (CTTL, No.J16X06809) Sep—17 Power sensor NRV—Z5 100595 22—Sep—16 (CTTL, No.J16X06808) Sep—17 ReferenceProbe EX3DV4 SN 7433 26—Sep—16(SPEAG,No.EX3—7433_Sep16) Sep—17 DAE4 SN 1331 19—Jan—17(CTTL—SPEAG,No.217—97015) Jan—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 13—Jan—17 (CTTL, No.J17X00286) Jan—18 NetworkAnalyzer ES071C MY46110673 13—Jan—17 (CTTL, No.J17X00285) Jan—18 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer 1‘{‘ Reviewed by: Lin Hao SAR Test Engineer Approved by: QiDianyuan SAR Project Leader Issued: July 1, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z17—97083 Page 1 of 14

w e_____________________ '\‘ in Collaboration with a=‘7"]"J, sn a $ e a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E : ettl@chinattl.com hitp://www.chinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessmentof specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30OMHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «_ Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. «_ Antenina Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. «_ Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connectorto the feed point. The Return Loss ensures low reflected power. No uncertainty required. «_ Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z17—97083 Page 2 of 14

0) m TTL 2.A ® In Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2070 ax: +86—10—62304633—2504 E—mail: eitl@chinattl.com hitps/wwwchinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1 DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4 mm, dz = 1.4 mm Graded Ratio = 1.4 (Z direction) 5250 MHz + 1 MHz Frequency 5600 MHz + 1 MHz 5750 MHz + 1 MHz Head TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0£0.2) °C 35.8 +6 % 4.63 mho/m + 6 % Head TSL temperature change during test <1.0 °C —— —— SAR result with Head TSL at 5250 MHz SAR averaged over 1 m‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 7.63 mW /g SAR for nominal Head TSL parameters normalized to 1W 76.2 mW Ig # 24.4 % (k=2) SAR averaged over 10 c‘ (10 g) of Head TSL Condition SAR measured 100 mW input power 2.18 mW /g SAR for nominal Head TSL parameters normalized to 1W 21.8 mW ig £ 24.2 % (k=2) Certificate No: Z17—97083 Page 3 of 14

U m ® in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinatt.com http:/iwwwchinattl.en Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36226 % 4.96 mho/m x 6 % Head TSL temperature change during test <1.0 °C — — SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.23 mW /g SAR for nominal Head TSL parameters normalized to 1W 82.6 mW ig £ 24.4 % (k=2) SAR averaged over 10 cn" (10 g) of Head TSL Condition SAR measured 100 mW input power 2.35 mW /g SAR for nominal Head TSL parameters normalized to 1W 23.6 mW /g £ 24.2 % (k=2) Head TSL parameters at 5750 MHz Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.2 +6 % 5.11 mhoim +6 % Head TSL temperature change during test <1.0 °C «—— —— SAR result with Head TSL at 5750 MHz SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.05 mW /g SAR for nominal Head TSL parameters normalized to 1W 80.8 mW Ig £ 24.4 % (k=2) SAR averaged over 10 cm" (10 g) of Head TS Condition SAR measured 100 mW input power 2.28 mW /g SAR for nominal Head TSL parameters normalized to 1W 22.9 mW Ig £ 24.2 % (k=2) Certificate No: Z17—97083 Page 4 of 14

U m ® in Collaboration with Ti L282 Add: No.51 Xueyuan Road, Haidian Dis ict, Beijing. 100191, China Tel 86—10—62304633—2070 Fax: +86—10—62304633—2504 : ettl@chinattl.com hitps/wwwchinattl.en Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL paramoters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 £0.2) °C 48.1 +6 % 5.42 mho/m + 6 % Body TSL temperature change during test <1.0 °C — — SAR result with Body TSL at 5250 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.54 mW /g SAR for nominal Body TSL parameters normalized to 1W 75.2 mW Ig £ 24.4 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 100 mW input power 2.13 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.2 mW ig + 24.2 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were led. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £0.2) °C 47.6 26 % 5.77 mholm 6 % Body TSL temperature change during test «1.0 °C —— —— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cCn‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.82 mW / g SAR for nominal Body TSL parameters normalized to 1W 77.9 mW Ig # 24.4 % (k=2) SAR averaged over 10 cn»"_(10 g) of Body TSL Condition SAR measured 100 mW input power 220 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.9 mW Ig 24.2 % (k=2) Certificate No: Z17—97083 Page 5 of 14

U s _i© in Collsboration with = TTL a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitpy/Awwwchinattl.en Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0£0.2) °C 47.5 £ 6 % 5.84 mho/m x 6 % Body TSL temperature change during test «10 °C — «—— SAR result with Body TSL at 5750 MHz SAR avoraged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 7.53 mW /g SAR for nominal Body TSL parameters normalized to 1W 75.0 mW Ig £ 24.4 % (k=2) SAR averaged over 10 Cm?" (10 g) of Body TSL Condition SAR measured 100 mW input power 2.12 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.1 mW Ig + 24.2 % (k=2) Certificate No: Z17—97083 Page 6 of 14

Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: eitl@chinattl.com hpy/wwmchinattl.cn Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 48.20 — 4.57)0 Return Loss —26.00B Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 55.20 + 2.14j0 Return Loss —25.40B Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 50.60 — 3.2510 Return Loss ~29.708 Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 47.90—2.79)0 Return Loss —29.008 Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.30 + 3.88J0 Return Loss —24.108 Antenna Parameters with Body TSL at 5750 MHz Impedance, transformed to feed point 51.90— 2200 Return Loss ~30.908 Certificate No: Z17—97083 Page 7 of14

J m r\* in Collaboration with m TTL a Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China le : +86—10—62304633—2070 Fax: +86—10—62304633—2504 I: ettl@chinattl.com hitps//wwmwchinattl.en General Antenna Parameters and Design Electrical Delay (onedirection) ] 1.315 ns After long term use with 100W radiated power, only a slight warming of the dipole nearthe feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to thedipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97083 Page 8 of 14

C mm 77L a s Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps/wwachinattlen DASY5 Validation Report for Head TSL Date: 06.29.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1200 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; a = 4.633 mho/m; er = 35.82; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 4.957 mho/m; er = 36.23; p = 1000 kg/im3, Medium parameters used: f = 5750 MHz; a = 5.107 mho/m; er = 36.17; p = 1000 kg/m3, Phantom section: Left Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7433; ConvF(5.13,5.13,5.13); Calibrated: 2016/9/26, ConvF(4.59,4.59,4.59); Calibrated: 2016/9/26, ConvF(4.66,4.66,4.66); Calibrated: 2016/9/26, * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1331; Calibrated: 2017/1/19 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration /Pin=100mW, d=10mm, f=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.36 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 30.2 Wikg SAR(1 g) = 7.63 Wikg; SAR(10 g) = 2.18 Wikg Maximum value of SAR (measured) = 18.0 W/kg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 54.3 V/im; Power Drift = 0.01 dB Peak SAR (extrapolated) = 33.9 W/kg SAR(1 g) = 8.23 Wikg; SAR(10 g) = 2.35 W/kg Maximum value of SAR (measured) = 19.4 Wikg Certificate No: Z17—97083 Page 9 of 14

@@n‘_—l a7T1Tr. gfi_&a_ Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62 504 E—mail: cttl@chinattl.com hitpi/wwwcchi Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 54.85 V/im; Power Drift = 0.02 dB Peak SAR (extrapolated) = 33.6 W/kg SAR(1 g) = 8.05 Wikg; SAR(10 g) = 2.28 Wikg Maximum value of SAR (measured) = 19.7 W/kg 0 dB = 19.7 Wikg = 12.94 dBWikg Certificate No: Z17—97083 Page 10 of 14

+86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps/wwwchinattl.en Impedance Measurement Plot for Head TSL Tri siX Log way 10. 00d87 mer 0. 000ds TF1] 5900. rs3—5.2500000 onz ~26.013 db ao.00 $. $:5990008 @HE "Be:eP oo 30. 00 20.c0 10.00 o. cc0p —10.00 ~20, 00 ~30. 00 ~40.00 a a snith (ReJ®) scale 1.000u [ri. vel] »r 3.2500000 onz «8.180 o —4.5607 n c.6l 2 $.6000000 one 55.218 0. 2.1404 0. 60,832 pn 5 $.7500000 onz 50.573 n —5.2488 0. 8:5199 pr & Certificate No: Z17—97083 Page 11 of 14

LCO‘ en C' in Collaboration with CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctl@chinatt.com hups/www.chinattl.en DASY5 Validation Report for Body TSL Date: 06.28.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5GHzV2 — SN: 1200 Communication System: CW; Frequency: 5250 MHz, Frequency: 5600 MHz, Frequency: 5750 MHz, Medium parameters used: f = 5250 MHz; a = 5.418 mho/m; er = 48.07; p = 1000 kg/m3, Medium parameters used: f = 5600 MHz; 0 = 5.767 mho/m; er = 47.59; p = 1000 kg/m3, Medium parameters used: f = 5750 MHz; a = 5.844 mho/m; &r = 47.51; p = 1000 kg/im3, Phantom section: Center Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS Configuration: * Probe: EX3DV4 — SN7433; ConvF(4.68,4.68,4.68); Calibrated: 2016/9/26, ConvF(3.98,3.98,3.98); Calibrated: 2016/9/26,ConvF(4.35,4.35,4.35); Calibrated: 2016/9/26, * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 2017/1/19 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/3 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration /Pin=100mW, d=10mm, f=5250 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 39.45 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 29.1 W/kg SAR(1 g) = 7.54 Wikg; SAR(10 g) = 2.13 Wikg Maximum value of SAR (measured) = 17.7 Wikg Dipole Calibration /Pin=100mW, d=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 62.62 V/im; Power Drift = —0.05 dB Peak SAR (extrapolated) = 32.9 W/kg SAR(1 g) = 7.82 Wikg; SAR(10 g) = 2.2 Wikg Maximum value of SAR (measured) = 18.7 Wikg Certificate No: Z17—97083 Page 12 of 14

:@@n_é T11 3—;1&9— Add: No.51 Xucyuan Road. Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304 5 E—mail: ettl@chinattl.com hitps/fwwwchinattl Dipole Calibration /Pin=100mW, d=10mm, f=5750 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.40 V/im; Power Drift = 0.04 dB Peak SAR (extrapolated) = 31.3 Wikg SAR(1 g) = 7.53 Wikg; SAR(10 g) = 2.12 Wikg Maximum value of SAR (measured) = 18.5 Wikg —10.00 20.00 —30.00 ~40.00 50.00 0 dB = 18.5 Wikg = 12.67 dBWikg Certificate No: Z17—97083 Page 13 of 14

Report No.: BL-SZ1870481-701 --END OF REPORT--


Document Created: 2018-09-13 20:26:30
Document Modified: 2018-09-13 20:26:30
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC