Report Z-wave rev.1

FCC ID: ZKJ-KITCHENHUB1

Test Report

Download: PDF
FCCID_4178281

Haier US Appliance Solutions, Inc. RF TEST REPORT Report Type: FCC Part 15.249 & ISED RSS-210 RF report Model: UVH13012M1SS Additional Model: See Page 2 REPORT NUMBER: 190100007SHA-008 ISSUE DATE: February 18, 2019 DOCUMENT CONTROL NUMBER: TTRF15.249_V1 © 2018 Intertek

Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 TEST REPORT www.intertek.com Report no.: 190100007SHA-008 Applicant: Haier US Appliance Solutions, Inc. Appliance Park AP2-226, Louisville, KY, 40225, United States Manufacturer: Haier US Appliance Solutions, Inc. Appliance Park AP2-226, Louisville, KY, 40225, United States Product Name: KITCHEN HUB Type/Model: UVH13012M1SS Additional Model: UVH13012M2SS, UVH13012M3SS, UVH13012M4SS, UVH13012M5SS, UVH13013M1DS, UVH13013M2DS, UVH13013M3DS, UVH13013M4DS, UVH13013M5DS, UVH13014M1WM, UVH13014M2WM, VH13014M3WM, UVH13014M4WM, UVH13014M5WM, UVH13013M1TS, UVH13013M2TS, UVH13013M3TS, UVH13013M4TS, UVH13013M5TS FCC ID: ZKJ-KITCHENHUB1 IC: 10229A-KITCHENHUB1 SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2017): Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices RSS‐210 Issue 9 (August 2016): Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment RSS‐Gen Issue 5 (April 2018): General Requirements for Compliance of Radio Apparatus PREPARED BY: REVIEWED BY: Project Engineer Reviewer Wade Zhang Daniel Zhao This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.249_V1 © 2018 Intertek Page 2 of 23

Report No.: 190100007SHA-008 TEST REPORT Content REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 6 1.3 ANTENNA INFORMATION....................................................................................................................................... 6 1.4 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST................................................................................................................... 8 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 8 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 9 2.5 TEST ENVIRONMENT CONDITION:............................................................................................................................ 9 2.6 INSTRUMENT LIST .............................................................................................................................................. 10 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 11 3 RADIATED EMISSIONS ............................................................................................................................... 12 3.1 LIMIT .............................................................................................................................................................. 12 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 13 3.3 TEST CONFIGURATION ........................................................................................................................................ 14 3.4 TEST RESULTS OF RADIATED EMISSIONS ................................................................................................................. 16 4 POWER LINE CONDUCTED EMISSION......................................................................................................... 17 4.1 LIMIT .............................................................................................................................................................. 17 4.2 TEST CONFIGURATION ........................................................................................................................................ 17 4.3 MEASUREMENT PROCEDURE ............................................................................................................................... 18 4.4 TEST RESULTS OF POWER LINE CONDUCTED EMISSION............................................................................................... 19 5 ASSIGNED BANDWIDTH (20DB BANDWIDTH) ............................................................................................ 21 5.1 LIMIT .............................................................................................................................................................. 21 5.2 MEASUREMENT PROCEDURE ............................................................................................................................... 21 5.3 TEST CONFIGURATION ........................................................................................................................................ 21 5.4 THE RESULTS..................................................................................................................................................... 22 6 ANTENNA REQUIREMENT .......................................................................................................................... 23 TTRF15.249_V1 © 2018 Intertek Page 3 of 23

Report No.: 190100007SHA-008 TEST REPORT Revision History Report No. Version Description Issued Date 190100007SHA-008 Rev. 01 Initial issue of report February 18, 2019 TTRF15.249_V1 © 2018 Intertek Page 4 of 23

Report No.: 190100007SHA-008 TEST REPORT Measurement result summary TEST ITEM FCC REFERANCE IC REFERANCE RESULT RSS-210 Issue 9 Radiated emission 15.249 & 15.209 Pass Clause B.10 RSS-Gen Issue 5 Power line conducted emission 15.207 Pass Clause 8.8 Assigned bandwidth RSS-Gen Issue 5 15.215(c) Pass (20dB bandwidth) Clause 6.7 Antenna requirement 15.203 - Pass Notes: 1: NA =Not Applicable 2. Determination of the test conclusion is based on IEC Guide 115 in consideration of measurement uncertainty. 3: Additions, Deviations and Exclusions from Standards: None. TTRF15.249_V1 © 2018 Intertek Page 5 of 23

Report No.: 190100007SHA-008 TEST REPORT 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: KITCHEN HUB Type/Model: UVH13012M1SS UVH13012M2SS, UVH13012M3SS, UVH13012M4SS, UVH13012M5SS, UVH13013M1DS, UVH13013M2DS, UVH13013M3DS, UVH13013M4DS, UVH13013M5DS, UVH13014M1WM, UVH13014M2WM, VH13014M3WM, UVH13014M4WM, UVH13014M5WM, UVH13013M1TS, UVH13013M2TS, Additional Model: UVH13013M3TS, UVH13013M4TS, UVH13013M5TS The EUT is a kitchen hood which was install wireless modules, there have 20 models, and they are electrically identical except different PCB silkscreen, different software version and the man-machine interface (not change the RF parameters), appearance skin and surface treatment Description of EUT: process. Rating: 120VAC 60Hz, 4A Software Version: / Hardware Version: / Sample received date: January 10, 2019 Date of test: January 10, 2019 ~ January 31, 2019 1.2 Technical Specification Frequency Range: 902-928MHz Type of Modulation: FSK Channel Frequency: 908.42MHz Channel Number: 1 channel 1.3 Antenna information Antenna No. Model Antenna type Antenna Gain Note 1 / Internal -1.0dBi TTRF15.249_V1 © 2018 Intertek Page 6 of 23

Report No.: 190100007SHA-008 TEST REPORT 1.4 Description of Test Facility Name: Intertek Testing Services Shanghai Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is CNAS Accreditation Lab recognized, Registration No. CNAS L0139 certified, or FCC Accredited Lab accredited by these Designation Number: CN1175 organizations: IC Registration Lab Registration code No.: 2042B-1 VCCI Registration Lab Registration No.: R-4243, G-845, C-4723, T-2252 A2LA Accreditation Lab Certificate Number: 3309.02 TTRF15.249_V1 © 2018 Intertek Page 7 of 23

Report No.: 190100007SHA-008 TEST REPORT 2 TEST SPECIFICATIONS 2.1 Standards or specification 47CFR Part 15 (2017) ANSI C63.10 (2013) RSS-210 Issue 9 (August 2016) RSS-Gen Issue 5 (April 2018) 2.2 Mode of operation during the test While testing transmitting mode of EUT, the internal modulation and continuously transmission was applied. The EUT can working at 3 data rates, and we tested date rate R3 as representatively. Channel Center frequency Data rate Bit rate Symbol rate Bandwidth (MHz) (*) (KHz) R3 100 Kbps 100 Kbaud 400 908.40 R2 40 Kbps 40 Kbaud 300 R1 9.6 Kbps 19.2 Kbaud 300 The UVH13012M1SS was chosen as a representative, and there have the following test mode: Radiated test mode: Mode 1: EUT transmitted signal with internal antenna; We have verified all test modes and choose the worst mode 1 for radiated test as representatively to list the results in this report. 2.3 Test software list Test Items Software Manufacturer Version Conducted emission ESxS-K1 R&S V2.1.0 Radiated emission ES-K1 R&S V1.71 TTRF15.249_V1 © 2018 Intertek Page 8 of 23

Report No.: 190100007SHA-008 TEST REPORT 2.4 Test peripherals list Item No. Name Band and Model Description 1 Laptop computer HP, 6470b AC 230V 50Hz 2.5 Test environment condition: Test items Temperature Humidity Minimum 6dB Bandwidth Maximum conducted output power and e.i.r.p. Power spectrum density 23C 52% RH Emission outside the frequency band Occupied bandwidth Radiated Emissions in restricted frequency bands 22C 55% RH Power line conducted emission 21C 52% RH TTRF15.249_V1 © 2018 Intertek Page 9 of 23

Report No.: 190100007SHA-008 TEST REPORT 2.6 Instrument list Conducted Emission Used Equipment Manufacturer Type Internal no. Due date Test Receiver R&S ESCS 30 EC 2107 2019-07-15 A.M.N. R&S ESH2-Z5 EC 3119 2019-11-30 Shielded room Zhongyu - EC 2838 2020-01-07 Radiated Emission Used Equipment Manufacturer Type Internal no. Due date Test Receiver R&S ESIB 26 EC 3045 2019-09-12 Bilog Antenna TESEQ CBL 6112D EC 4206 2019-06-10 Horn antenna R&S HF 906 EC 3049 2019-11-17 Horn antenna ETS 3117 EC 4792-1 2020-01-09 Horn antenna TOYO HAP18-26W EC 4792-3 2020-07-09 Pre-amplifier R&S Pre-amp 18 EC5262 2019-06-10 Semi-anechoic chamber Albatross project - EC 3048 2019-07-31 RF test Used Equipment Manufacturer Type Internal no. Due date PXA Signal Analyzer Keysight N9030A EC 5338 2019-03-05 PXA Signal Analyzer Keysight N9030B EC 6078 2019-12-22 Power sensor Agilent U2021XA EC 5338-1 2019-03-05 Vector Signal Generator Agilent N5182B EC 5175 2019-03-05 MXG Analog Signal Generator Agilent N5181A EC 5338-2 2019-03-05 Test Receiver R&S ESCI 7 EC 4501 2019-09-12 Additional instrument Used Equipment Manufacturer Type Internal no. Due date Therom-Hygrograph ZJ1-2A S.M.I.F. EC 3783 2019-02-28 Pressure meter YM3 Shanghai Mengde EC 3320 2019-07-01 TTRF15.249_V1 © 2018 Intertek Page 10 of 23

Report No.: 190100007SHA-008 TEST REPORT 2.7 Measurement uncertainty The measurement uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Test item Measurement uncertainty Maximum peak output power  0.74dB Radiated Emissions in restricted frequency bands  4.90dB below 1GHz Radiated Emissions in restricted frequency bands  5.02dB above 1GHz Emission outside the frequency band  2.89dB Power line conducted emission  3.19dB TTRF15.249_V1 © 2018 Intertek Page 11 of 23

Report No.: 190100007SHA-008 TEST REPORT 3 Radiated Emissions Test result: Pass 3.1 Limit Fundamental Frequency Fundamental limit Harmonic limit (MHz) (dBuV/m) (dBuV/m) 902 - 928 94 54 2400 - 2483.5 94 54 5725 - 5875 94 54 24000 - 24250 108 68 The radiated emissions which fall in the restricted bands, must also comply with the radiated emission limits specified showed as below: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 TTRF15.249_V1 © 2018 Intertek Page 12 of 23

Report No.: 190100007SHA-008 TEST REPORT 3.2 Measurement Procedure For Radiated emission below 30MHz: a) The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c) Both X and Y axes of the antenna are set to make the measurement. d) For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e) The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz: a) The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c) The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d) For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e) The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f) The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 3 x RBW (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported TTRF15.249_V1 © 2018 Intertek Page 13 of 23

Report No.: 190100007SHA-008 TEST REPORT 3.3 Test Configuration For Radiated emission below 30MHz: EUT& 3m Support Units Turn Table 80cm Test Receiver For Radiated emission 30MHz to 1GHz: Ant. Tower 1‐4m Variable EUT& 3m Support Units Turn Table 80cm Test Receiver TTRF15.249_V1 © 2018 Intertek Page 14 of 23

Report No.: 190100007SHA-008 TEST REPORT For Radiated emission above 1GHz: Ant. Tower 1‐4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Test Receiver TTRF15.249_V1 © 2018 Intertek Page 15 of 23

Report No.: 190100007SHA-008 TEST REPORT 3.4 Test Results of Radiated Emissions Consider simultaneous transmission, EUT was tested with Zigbee, WIFI and BLE on and off, and the worst data was listed in the report. The low frequency, which started from 9 kHz to 30MHz, was pre- scanned and the result which was 20dB lower than the limit line per 15.31(o) was not reported. Corrected Frequency Correct Factor Limit Margin Antenna Reading Detector (MHz) (dB/m) (dBuV/m) (dB) (dBuV/m) H 30.00 23.10 18.60 40.00 16.90 PK H 57.21 18.80 7.30 40.00 21.20 PK H 74.71 19.70 7.50 40.00 20.30 PK H 146.63 39.90 11.90 43.50 3.60 PK H 197.17 26.50 10.90 43.50 17.00 PK H 296.31 34.10 14.70 46.00 11.90 PK H 451.82 32.80 18.60 46.00 13.20 PK H 601.50 28.10 20.80 46.00 17.90 PK H 908.42 88.50 23.50 94.00 5.50 PK H 1816.84 43.70 29.30 54.00 10.30 PK V 30.00 34.40 18.60 40.00 5.60 PK V 47.49 33.60 9.70 40.00 6.40 PK V 61.10 33.30 6.90 40.00 6.70 PK V 111.64 20.40 12.70 43.50 23.10 PK V 148.58 36.30 11.80 43.50 7.20 PK V 197.17 29.70 10.90 43.50 13.80 PK V 300.20 29.40 14.70 46.00 16.60 PK V 451.82 30.90 18.60 46.00 15.10 PK V 595.67 27.10 20.70 46.00 18.90 PK V 908.42 86.30 23.50 94.00 7.70 PK V 1816.84 43.60 29.30 54.00 10.40 PK Remark: 1. Correct Factor = Antenna Factor + Cable Loss (+ Amplifier, for higher than 1GHz), the value was added to Original Receiver Reading by the software automatically. 2. Corrected Reading = Original Receiver Reading + Correct Factor 3. Margin = Limit - Corrected Reading 4. If the PK Corrected Reading is lower than AV limit, the AV test can be elided. Example: Assuming Antenna Factor = 30.20dB/m, Cable Loss = 2.00dB, Gain of Preamplifier = 32.00dB, Original Receiver Reading = 10.00dBuV, Limit = 40.00dBuV/m. Then Correct Factor = 30.20 + 2.00 – 32.00 = 0.20dB/m; Corrected Reading = 10dBuV + 0.20dB/m = 10.20dBuV/m; Margin = 40.00dBuV/m - 10.20dBuV/m = 29.80dB. TTRF15.249_V1 © 2018 Intertek Page 16 of 23

Report No.: 190100007SHA-008 TEST REPORT 4 Power line conducted emission Test result: Pass 4.1 Limit Conducted Limit (dBuV) Frequency of Emission (MHz) QP AV 0.15-0.5 66 to 56* 56 to 46 * 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. 4.2 Test Configuration EUT Peripheral devices LISN LISN EMI receiver TTRF15.249_V1 © 2018 Intertek Page 17 of 23

Report No.: 190100007SHA-008 TEST REPORT 4.3 Measurement Procedure Measured levels of ac power-line conducted emission shall be the emission voltages from the voltage probe, where permitted, or across the 50 Ω LISN port (to which the EUT is connected), where permitted, terminated into a 50 Ω measuring instrument. All emission voltage and current measurements shall be made on each current-carrying conductor at the plug end of the EUT power cord by the use of mating plugs and receptacles on the LISN, if used. Equipment shall be tested with power cords that are normally supplied or recommended by the manufacturer and that have electrical and shielding characteristics that are the same as those cords normally supplied or recommended by the manufacturer. For those measurements using a LISN, the 50 Ω measuring port is terminated by a measuring instrument having 50 Ω input impedance. All other ports are terminated in 50 Ω loads. Tabletop devices shall be placed on a platform of nominal size 1 m by 1.5 m, raised 80 cm above the reference ground plane. The vertical conducting plane or wall of an RF-shielded (screened) room shall be located 40 cm to the rear of the EUT. Floor-standing devices shall be placed either directly on the reference ground-plane or on insulating material as described in ANSI C63.4. All other surfaces of tabletop or floor-standing EUTs shall be at least 80 cm from any other grounded conducting surface, including the case or cases of one or more LISNs. The bandwidth of the test receiver is set at 9 kHz. TTRF15.249_V1 © 2018 Intertek Page 18 of 23

Report No.: 190100007SHA-008 TEST REPORT 4.4 Test Results of Power line conducted emission Test Curve: L Line Test Data: Quasi‐peak Average Frequency (MHz) level Limit Margin level limit Margin dB(V) dB(V) (dB) dB(V) dB(V) (dB) 0.315 47.17 59.83 12.66 39.73 49.83 10.10 1.131 44.61 56.00 11.39 29.65 46.00 16.35 2.009 46.54 56.00 9.46 32.29 46.00 13.71 2.765 44.62 56.00 11.38 32.90 46.00 13.10 5.052 40.26 60.00 19.74 32.10 50.00 17.90 14.964 32.26 60.00 27.74 22.22 50.00 27.78 TTRF15.249_V1 © 2018 Intertek Page 19 of 23

Report No.: 190100007SHA-008 TEST REPORT Test Curve: N Line Test Data: Quasi‐peak Average Frequency (MHz) level Limit Margin level limit Margin dB(V) dB(V) (dB) dB(V) dB(V) (dB) 0.475 45.74 56.42 10.68 39.50 46.42 6.92 0.789 47.03 56.00 8.97 37.22 46.00 8.78 1.061 47.15 56.00 8.85 38.45 46.00 7.55 1.747 45.91 56.00 10.09 37.68 46.00 8.32 2.901 46.43 56.00 9.57 41.61 46.00 4.39 23.968 24.57 60.00 35.43 18.89 50.00 31.11 Remark: 1. Correct Factor = LISN Factor + Cable Loss, the value was added to Original Receiver Reading by the software automatically. 2. Corrected Reading = Original Receiver Reading + Correct Factor 3. Margin = Limit ‐ Corrected Reading 4. If the PK Corrected Reading is lower than AV limit, the AV test can be elided. TTRF15.249_V1 © 2018 Intertek Page 20 of 23

Report No.: 190100007SHA-008 TEST REPORT 5 Assigned bandwidth (20dB bandwidth) Test result: Pass 5.1 Limit Intentional radiators must be designed to ensure that the 20dB bandwidth of the emission is contained within the allocated frequency band. 5.2 Measurement Procedure The 20dB Bandwidth is measured using the Spectrum Analyzer. Set Span = 2 to 3 times the 20 dB bandwidth, RBW = approximately 1% of the 20 dB bandwidth, VBW˃RBW, Sweep = auto, Detector = peak, Trace = max hold. The test was performed at 2 channels (lowest and highest channel). 5.3 Test Configuration EUT Spectrum Analyzer TTRF15.249_V1 © 2018 Intertek Page 21 of 23

Report No.: 190100007SHA-008 TEST REPORT 5.4 The results 20dB Bandwidth 99% Bandwidth FL FH Channel Frequency (kHz) (kHz) (MHz) (MHz) 908.4MHz 123.7 109.98 ˃ 902 ˂ 928 TTRF15.249_V1 © 2018 Intertek Page 22 of 23

Report No.: 190100007SHA-008 TEST REPORT 6 Antenna requirement Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. Result: EUT uses used a no-standard electrical connector antenna to the intentional radiator, so it can comply with the provisions of this section. **************************************** END **************************************** TTRF15.249_V1 © 2018 Intertek Page 23 of 23


Document Created: 2019-02-22 16:20:04
Document Modified: 2019-02-22 16:20:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC