M1_BB1737-25 MAL-U

FCC ID: ZKJ-BLEA003

Cover Letter(s)

Download: PDF
FCCID_2878026

Applicant GE Appliance & Lighting FCC ID: ZKJ-BLEA003 Section 15.212 Modular Transmitters Request for Modular Approval Y Request for Limited Modular Approval Comply Requirements EUT Conditions (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular Yes, this RF Module has own RF Y transmitter must have their own shielding and therefore comply shielding. The physical crystal and to this requirement.The RF Module is tuning capacitors may be located subject to Professional Installation external to the shielded radio and Integrator is advised by the elements. integration manual how to assure compliance of final end-product into which this RF Module is integrated to the FCC regulations. 2 The modular transmitter must have Please refer the Schematic, The modular Y buffered modulation/data inputs (if transmitter have buffered modulation/data such inputs are provided) to ensure inputs U1 that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3 The modular transmitter must have its The modular has it’s own power supply Y own power supply regulation. regulation. 4 The modular transmitter must comply Referring to onboard PCB antenna Y with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section.

5 The modular transmitter must be Referring to the test setup photos. This Y tested in a stand-alone configuration, module is tested in a stand-alone i.e., the module must not be inside configuration. another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)).

6 The modular transmitter must be The modular was labeled with its own Y equipped with either a permanently FCC ID. The outside of device in to affixed label or must be capable of which the module is installed will electronically displaying its FCC labeled ‘Contains TX FCC ID: identification number. (A) If using a ZKJ-BLEA003, Please refer to User permanently affixed label, the modular Manual transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization.

7 The modular transmitter must comply The modular is comply with all Y with any specific rules or operating applicable FCC rules. requirements that ordinarily apply to a Any modifications, not expressly complete transmitter and the approved by the manufacturer could manufacturer must provide adequate void the authority to operate in these instructions along with the module to regions. explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8 The modular transmitter must comply With the documented max output power Y with any applicable RF exposure this RF Module meets the FCC SAR requirements in its final configuration. Exemption - so it can be integrated in any host device (portable/mobile/fixed) with further restrictions. A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Signature GE Appliance & Lighting Contact person: Rob Bultman Title: Manager


Document Created: 2016-01-16 10:17:00
Document Modified: 2016-01-16 10:17:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC