Modular-Approval-Letter

FCC ID: ZI8EA45

Cover Letter(s)

Download: PDF

                                                                          BossPac Engineering And Technology
                                                        Applicant:                                                               FCC ID:       ZI8EA45
                                                                          Inc.
                                                Test Report S/N:          45461472-R2.0                                          ISED ID       9648A-EA45



EXHIBIT 6 – FCC MODULAR APPROVAL LETTER


                                                                           See Attached




   ©2019 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the expressed written permission of Celltech Labs Inc.   Page 9 of 48


Date: 17 January 2019

TO:
Federal Communications Commission
Authorization and Evaluation Division
7435 Oakland Mills Rd.
Columbia, MD 21046

RE: [Single[Limited][Split] Modular Approval Attestation of FCC ID: ZI8EA45

This is a request for a [Single[Limited][Split] Modular Approval of FCC ID: ZI8EA45 in accordance with 47
CFR 15.212(b). The following is a declaration of conditions. A ✔ denotes compliance to the applicable
rule part.

 §15.212 Modular transmitters.

 (a) Single modular transmitters consist of a completely self-contained radiofrequency transmitter device that is
 typically incorporated into another product, host or device. Split modular transmitters consist of two
 components: a radio front end with antenna (or radio devices) and a transmitter control element (or specific
 hardware on which the software that controls the radio operation resides). All single or split modular
 transmitters are approved with an antenna. All of the following requirements apply, except as provided in
 paragraph (b) of this section.
 (1) Single modular transmitters must meet the following requirements to obtain a modular transmitter approval.

             (i) The radio elements of the modular transmitter must have their own shielding. The physical
             crystal and tuning capacitors may be located external to the shielded radio elements.

     ✔       (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided)
             to ensure that the module will comply with part 15 requirements under conditions of excessive data
             rates or over-modulation.
             (iii) The modular transmitter must have its own power supply regulation.


     ✔       (iv) The modular transmitter must comply with the antenna and transmission system requirements
             of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ
             a “unique” antenna coupler (at all connections between the module and the antenna, including the
             cable). The “professional installation” provision of §15.203 is not applicable to modules but can
             apply to limited modular approvals under paragraph (b) of this section.

             (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not
             be inside another device during testing for compliance with part 15 requirements. Unless the
             transmitter module will be battery powered, it must comply with the AC line conducted
             requirements found in §15.207. AC or DC power lines and data input/output lines connected to the
             module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)).
             The length of these lines shall be the length typical of actual use or, if that length is unknown, at
             least 10 centimeters to insure that there is no coupling between the case of the module and
             supporting equipment. Any accessories, peripherals, or support equipment connected to the
             module during testing shall be unmodified and commercially available (see §15.31(i)).

     ✔       (vi) The modular transmitter must be equipped with either a permanently affixed label or must be

_____________________________________________________________________________________
                                         BossPac Engineering & Technology
                                 th
                          1450 28 Street NE, Bay 8, Calgary, Alberta, CANADA, T2A 7W6
                                      Toll Free 866-616-1226 www.bosspac.com


             capable of electronically displaying its FCC identification number.
                       (A) Manufacturers must ensure that only transmitter control elements and radio front end
                       components that have been approved together are capable of operating together. The
                       transmitter module must not operate unless it has verified that the installed transmitter
                       control elements and radio front end have been authorized together. Manufacturers may
                       use means including, but not limited to, coding in hardware and electronic signatures in
                       software to meet these requirements, and must describe the methods in their application
                       for equipment authorization.
                       (B) If the modular transmitter uses an electronic display of the FCC identification number,
                       the information must be readily accessible and visible on the modular transmitter or on the
                       device in which it is installed. If the module is installed inside another device, then the
                       outside of the device into which the module is installed must display a label referring to
                       the enclosed module. This exterior label can use wording such as the following: “Contains
                       FCC certified transmitter module(s).” Any similar wording that expresses the same
                       meaning may be used. The user manual must include instructions on how to access the
                       electronic display. A copy of these instructions must be included in the application for
                       equipment authorization.
      ✔      (vii) The modular transmitter must comply with any specific rules or operating requirements that
             ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions
             along with the module to explain any such requirements. A copy of these instructions must be
             included in the application for equipment authorization.

      ✔      viii) The modular transmitter must comply with any applicable RF exposure requirements in its final
             configuration.

      ✔      (iv) Manufacturers must ensure that only transmitter control elements and radio front end
             components that have been approved together are capable of operating together. The transmitter
             module must not operate unless it has verified that the installed transmitter control elements and
             radio front end have been authorized together. Manufacturers may use means including, but not
             limited to, coding in hardware and electronic signatures in software to meet these requirements,
             and must describe the methods in their application for equipment authorization.

 (b) A limited modular approval may be granted for single or split modular transmitters that do not comply with all
 of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or
 power supply regulation, if the manufacturer can demonstrate by alternative means in the application for
 equipment authorization that the modular transmitter meets all the applicable part 15 requirements under the
 operating conditions in which the transmitter will be used. Limited modular approval also may be granted in
 those instances where compliance with RF exposure rules is demonstrated only for particular product
 configurations. The applicant for certification must state how control of the end product into which the module
 will be installed will be maintained such that full compliance of the end product is always ensured.


Attestation:
This is an application for a limited single modular approval. This module is not intended to be sold or
distributed to 3rd party integrators and the manufacture and integration of this module is strictly under the
control of BossPac Engineering and Technology Inc. This module is intended to be integrated only into
those host products identified in this application. The host products are industrial in nature and are not to
be sold or distributed to the general public. The host products are to be installed by professionally trained
personnel only and under the guidance of BossPac Engineering and Technology Inc.

_____________________________________________________________________________________
                                          BossPac Engineering & Technology
                                  th
                           1450 28 Street NE, Bay 8, Calgary, Alberta, CANADA, T2A 7W6
                                       Toll Free 866-616-1226 www.bosspac.com


     Applicant
       Name:
                                 Anthony Bastiaansen                               Applicant Title:    Engineer

     Applicant
    Signature:
                                                                                   Signature Date:    17 Jan 2019




_____________________________________________________________________________________
                                    BossPac Engineering & Technology
                            th
                     1450 28 Street NE, Bay 8, Calgary, Alberta, CANADA, T2A 7W6
                                 Toll Free 866-616-1226 www.bosspac.com



Document Created: 2019-01-17 12:24:39
Document Modified: 2019-01-17 12:24:39

© 2019 FCC.report
This site is not affiliated with or endorsed by the FCC