MPE

FCC ID: ZHK-HS00021

RF Exposure Info

Download: PDF
FCCID_4306050

         CERPASS TECHNOLOGY CORP.                                          Report No.: TEFI1904074-975


  12. Radio Frequency Exposure
    12.1 Applicable Standards
         The measurements shown in this test report were made in accordance with the procedures given in
         FCC Part 2 (Section 2.1093)
         KDB 447498
         IEEE C95.1


         LIMIT

         KDB 447498 D01 § 4.3(a)
         For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test
         exclusion thresholds are determined by the following:
         [(max. power of channel, including tune-up tolerance, mW) / (min. test separation
         distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extrem

         *f(GHz) is the RF channel transmit frequency in GHz


         *The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below

         The test exclusions are applicable only when the minimum test separation distance is ≤
         50 mm, and for transmission frequencies between 100 MHz and 6 GHz. When the
         minimum test separation distance is < 5 mm, a distance of 5 mm according to 4.1 f) is
         applied to determine SAR test exclusion


    12.2 EUT Specification
          Frequency band               SRD: 2400MHz ~ 2483.5MHz
          (Operating)                  Bluetooth: 2402MHz ~ 2480MHz
                                       Portable (<20cm separation)
          Device category
                                       Mobile (>20cm separation)
          Exposure                     Occupational/Controlled exposure
          classification               General Population/Uncontrolled exposure
                                       Single antenna
                                       Multiple antennas
          Antenna diversity                Tx diversity
                                           Rx diversity
                                           Tx/Rx diversity
                                       MPE Evaluation*
          Evaluation applied           SAR Evaluation
                                       N/A
         Remark:

          1. The maximum conducted output power is 4.19dBm (2.624mW) at 2403.35MHz (with
             1.58dBi antenna gain.)
          2. DTS device is not subject to routine RF evaluation; MPE estimate is used to justify the
             compliance.
          3. For mobile or fixed location transmitters, no SAR consideration applied.
         *Note: Simultaneous transmission is not applicable for this EUT.


Cerpass Technology Corp.                                                      Issued Date :    May. 16, 2019
T-FD-506-0 Ver 1.0                                                            Page No.     :   49 of 50
                                                                              FCC ID.      :   ZHK-HS00021


         CERPASS TECHNOLOGY CORP.                                      Report No.: TEFI1904074-975



    12.3 Test Results
        According to the KDB447498:
         The SAR test exclusion thresholds Level:
         [(max. power of channel, including tune-up tolerance, mW) /(min. test separation distance,
         mm)] * sqrt (freq. in GHz) < 3

         Calculation

         ANT1
                                                                                              SAR test exclusion
           Channel Frequency        Max. Conducted        Max. Conducted       Distance
                                                                                                   thresholds
                    (MHz)          output power(dBm)     output power(mW)          (mm)
                                                                                                       (mW)
            2403.35-2477.35               4.19                 2.624                5                  10.00

         ANT2
                                                                                              SAR test exclusion
           Channel Frequency        Max. Conducted        Max. Conducted       Distance
                                                                                                   thresholds
                    (MHz)          output power(dBm)     output power(mW)          (mm)
                                                                                                       (mW)
            2403.35-2477.35               3.85                 2.427                5                  10.00


         Since the source-based time-averaging conducted output power is well below the SAR
          low threshold level, so the EUT is considered to comply with SAR requirement without
          testing




Cerpass Technology Corp.                                                 Issued Date :      May. 16, 2019
T-FD-506-0 Ver 1.0                                                       Page No.       :   50 of 50
                                                                         FCC ID.        :   ZHK-HS00021



Document Created: 2019-05-28 15:20:12
Document Modified: 2019-05-28 15:20:12

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC