Test Report

FCC ID: ZFT-K105

Test Report

Download: PDF
FCCID_1453237

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 FCC 47 CFR PART 15 SUBPART B TEST REPORT for Mobile Phone MODEL: K105,P32D Trade Name: B-mobile Test Report Number: KS110407B01-EF Issued to: Global Mobile Communication (HK) Ltd., 7/F,Kin On Commercial Building,49-51 Jervois Street,Sheung Wan,HongKong,China Issued by: Compliance Certification Services Inc. Linkuo Laboratory No. 81-1, Lane 210, Pa-De 2nd Rd., Luchu Hsiang, Taoyuan Shien, (338), Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Issued Date: April 14, 2011 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by , A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 1 / 28

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Revision History Effect Page Rev. Issue Date Revisions Revised By 00 April 14, 2011 Initial Issue ALL Hadiif.Hoo Page 2 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION................................................................................... 4 2 EUT DESCRIPTION........................................................................................................... 5 3 TEST METHODOLOGY ................................................................................................... 6 3.1. DECISION OF FINAL TEST MODE ....................................................................................................6 4 SETUP OF EQUIPMENT UNDER TEST ........................................................................ 7 4.1. DESCRIPTION OF SUPPORT UNITS................................................................................................7 4.2. CONFIGURATION OF SYSTEM UNDER TEST ................................................................................8 5 FACILITIES AND ACCREDITATIONS ......................................................................... 9 5.1. FACILITIES..........................................................................................................................................9 5.2. ACCREDITATIONS .............................................................................................................................9 5.3. MEASUREMENT UNCERTAINTY ......................................................................................................9 5.4. LIST OF TEST EQUIPMENT ............................................................................................................10 6 CONDUCTED EMISSION MEASUREMENT.............................................................. 12 6.1. LIMITS OF CONDUCTED EMISSION MEASUREMENT .................................................................12 6.2. TEST INSTRUMENTS ......................................................................................................................12 6.3. TEST PROCEDURES .......................................................................................................................13 6.4. TEST SETUP.....................................................................................................................................14 6.5. DATA SAMPLE..................................................................................................................................14 6.6. TEST RESULTS ................................................................................................................................15 7 RADIATED EMISSION MEASUREMENT .................................................................. 17 7.1. LIMITS OF RADIATED EMISSION MEASUREMENT ......................................................................17 7.2. TEST INSTRUMENTS ......................................................................................................................19 7.3. TEST PROCEDURES .......................................................................................................................19 7.4. TEST SETUP.....................................................................................................................................21 7.5. DATA SAMPLE..................................................................................................................................22 7.6. TEST RESULTS ................................................................................................................................23 PHOTOGRAPHS OF THE TEST CONFIGURATION ........................................................... 27 APPENDIX 1 - PHOTOGRAPHS OF EUT ...................................................................A1-1 Page 3 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 1 TEST RESULT CERTIFICATION Product Name: Mobile Phone Model No.: K105, P32D Brand Name: B-mobile Applicant: Global Mobile Communication (HK) Ltd., Address : 7/F,Kin On Commercial Building,49-51 Jervois Street,Sheung Wan,HongKong,China Manufacturer: Water World Technology Co., Ltd Address : 6 Floor, Block B, Digital Building, Garden City,No.1079.Nanhai Road, NanshanDistrict, Shenzhen, Guangdong, China Tested Date: April 12,2011-April 14,2011 EMISSION Standard Item Result Remarks FCC 47 CFR Part 15 Subpart B, Conducted (Power Port) PASS Meet Class B limit ICES-003 Issue 4 ANSI C63.4-2009 Radiated PASS Meet Class B limit Note: 1. The statements of test result on the above are decided by the request of test standard only; the measurement uncertainties are not factored into this compliance determination. 2. The information of measurement uncertainty is available upon the customer’s request. Deviation from Applicable Standard None The above equipment has been tested by Compliance Certification Services Inc., and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved by: Reviewed by: Hadiif.Hoo Dohnny.Lu EMC Manager EMC Section Manager Compliance Certification Service Inc. Compliance Certification Service Inc. Page 4 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 2 EUT DESCRIPTION Product Name Mobile Phone Brand Name B-mobile Model Number K105,P32D FCC ID FCC ID: ZFT-K105 Applicant Global Mobile Communication (HK) Ltd., Housing material plastic casing EUT Type Engineering Sample. Product Sample. Mass Product Sample. Powered from an AC/DC power adapter Model Number :UTC-24 Input:100-240V 200mA 50-60Hz Output:5.0V 500mA EUT Power Rating Battery Model: BL-5B Standard Voltage:3.7V Rating Capacity:600mAh AC Power Cord Type N/A I/O Cable Type Shielded,1m I/O PORT I/O PORT TYPES Q’TY TESTED WITH 1. Micro B Port 1 1 Page 5 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 3 TEST METHODOLOGY 3.1. DECISION OF FINAL TEST MODE The EUT was tested together with the above additional components, and a configuration, which produced the worst emission levels, was selected and recorded in this report. The test configuration modes are as the following: Conduction Modes: 1 Micro B Port Data rate 2 Micro B Port Adapter Radiation Modes: 1 Micro B Port Data rate 2 Micro B Port Adapter After the preliminary scan, the following test mode was found to produce the final emission level. Conduction: Mode 2 Radiation: Mode 2 Page 6 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 4 SETUP OF EQUIPMENT UNDER TEST 4.1. DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Trade Data No. Equipment Model No. Serial No. FCC ID Power Cord Name Cable Shielded, 1.8m Un-Shielded, 1 PC 6010GC CNG44001T2 DoC HP with two 1.8m Core Note: 1) All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2) Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 7 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 4.2. CONFIGURATION OF SYSTEM UNDER TEST Receiver 120VAC **EUT (Included Support units) Test Table Page 8 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 5 FACILITIES AND ACCREDITATIONS 5.1. FACILITIES All measurement facilities used to collect the measurement data are located at No. 81-1, Lane 210, Pa-De 2nd Rd., Luchu Hsiang, Taoyuan Shien, Taiwan. The sites are constructed in conformance with the requirements of ANSI C63.4 and CISPR 22. All receiving equipment conforms to CISPR 16-1-1, CISPR 16-1-2, CISPR 16-1-3, CISPR 16-1-4, CISPR 16-1-5. 5.2. ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. USA A2LA The measuring facility of laboratories has been authorized or registered by the following approval agencies. Canada Industry Canada Japan VCCI Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site, http:///www.ccsrf.com 5.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Measurement Frequency Uncertainty Conducted emissions 0.15MHz~30MHz ± 3.43 dB Measurement Polarity Frequency Uncertainty 30MHz ~ 200MHz +/- 4.72dB H Radiated emissions 200MHz ~1000MHz +/- 4.72dB (below 1GHz) 30MHz ~ 200MHz +/- 4.83dB V 200MHz ~1000MHz +/- 4.70dB 1000MHz ~5000MHz +/- 3.92dB H Radiated emissions 5000MHz ~8000MHz +/- 3.94dB (above 1GHz) 1000MHz ~5000MHz +/- 3.92dB V 5000MHz ~8000MHz +/- 3.93dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Consistent with industry standard (e.g. CISPR 22: 2005, clause 11, Measurement Uncertainty) determining compliance with the limits shall be base on the results of the compliance measurement. Consequently the measure emissions being less than the maximum allowed Page 9 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 emission result in this be a compliant test or passing test. The acceptable measurement uncertainty value without requiring revision of the compliance statement is base on conducted and radiated emissions being less than UCISPR which is 3.6dB and 5.2dB respectively. CCS values (called ULab in CISPR 16-4-2) is less than UCISPR as shown in the table above. Therefore, MU need not be considered for compliance. 5.4. LIST OF TEST EQUIPMENT Conducted Emission Name of Equipment Manufacturer Model Serial Number Calibration Due EMI TEST RECEIVER R&S ESCI3 100781 04/29/2011 V (V-LISN) Schwarzbeck NNLK 8129 8129-143 04/29/2011 FCC-LISN-50/250-5 LISN (EUT) FCC SN:05012 04/29/2011 0-2-02 TRANSIENT LIMITER SCHAFFNER CFL9206 1710 04/29/2011 Test Software EZ-EMC NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. Radiated Emission (Test Site A (10m chamber) for 30MHz-1GHz) Name of Equipment Manufacturer Model Serial Number Calibration Due EMI Test Receiver R&S ESI26 100068 05/26/2011 Bilog Antenna Sunol JB1 A110204 06/24/2011 Pre-Amplifier Anritsu MH648A M64192 05/28/2011 System Controller Sunol SC99V 121501-1 N.C.R. Turn Table Sunol FM3022HS N/A N.C.R. Antenna Mast Sunol TWR 99-4 121501-3 N.C.R. Test Software EZ-EMC NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. Page 10 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Radiated Emission (3M Semi Anechoic Chamber (977) For 1 GHz -18GHz) Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A MY44020154 05/26/2011 EMI Test Receiver R&S ESPI3 101026 04/29/2011 Pre-Amplfier MINI ZFL-1000VH2 d041703 06/30/2011 Pre-Amplfier Miteq NSP4000-NF 870629 06/30/2011 Bilog Antenna Sunol JB1 A110204-2 06/24/2011 Horn-antenna SCHWARZBECK BBHA9120D D:266 05/07/2011 Turn Table CT CT123 4165 N.C.R Antenna Tower CT CTERG23 3256 N.C.R Controller CT CT1OO 95637 N.C.R Test Software EZ-EMC NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2.N.C.R = No Calibration Request. Page 11 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 6 CONDUCTED EMISSION MEASUREMENT 6.1. LIMITS OF CONDUCTED EMISSION MEASUREMENT Class A (dBuV) Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range 0.15 to 0.50 MHz. (3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 6.2. TEST INSTRUMENTS See list of test equipment of this test report. Page 12 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 6.3. TEST PROCEDURES Procedure of Preliminary Test z The EUT and support equipment, if needed, were set up as per the test configuration to simulate typical usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor standing equipment, it is placed on the ground plane, which has a 12 mm non-conductive covering to insulate the EUT from the ground plane. z All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. z The test equipment EUT installed by AC 120VAC/60Hz main power, through a Line Impedance Stabilization Network (LISN), which was supplied power source and was grounded to the ground plane. z All support equipment power by from a second LISN. z The test program of the EUT was started. Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT. z The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes. z During the above scans, the emissions were maximized by cable manipulation. z The test mode(s) described in Item 3.1 were scanned during the preliminary test. z After the preliminary scan, we found the test mode described in Item 3.1 producing the highest emission level. z The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test. Procedure of Final Test z EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test. z A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. z The test data of the worst-case condition(s) was recorded. Page 13 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 6.4. TEST SETUP Vert. reference plane EMI receiver 40cm EUT 80cm LISN Reference ground plane z For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 6.5. DATA SAMPLE Frequency QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Reading Reading Factor Result Result Limit Limit Margin Margin (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) x.xx 35.81 34.89 10.16 45.97 45.05 59.93 49.93 -13.96 -4.88 Correction factor (dB) = cable loss + Insertion loss of LISN+ Insertion loss of transient limiter (The transient limiter included 10 dB attenuation) (QuasiPeak/ Average)Result = (QuasiPeak/ Average)reading + Correction Factor (dB) Calculation Formula (QuasiPeak/ Average)Margin (dB) = (QuasiPeak/ Average)Result (dBuV) –(QuasiPeak/ Average)Limit (dBuV) Page 14 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 6.6. TEST RESULTS L1 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average No. Frequency Remark reading reading factor result result limit limit margin margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 1 0.1546 36.99 25.65 10.05 47.04 35.70 65.75 55.75 -18.71 -20.05 Pass 2* 0.5398 30.62 22.25 10.84 41.46 33.09 56.00 46.00 -14.54 -12.91 Pass 3 0.6170 30.71 22.15 10.89 41.60 33.04 56.00 46.00 -14.40 -12.96 Pass 4 1.1596 30.03 20.46 11.03 41.06 31.49 56.00 46.00 -14.94 -14.51 Pass 5 1.6212 30.70 19.85 11.06 41.76 30.91 56.00 46.00 -14.24 -15.09 Pass 6 2.1604 29.04 17.16 11.10 40.14 28.26 56.00 46.00 -15.86 -17.74 Pass Note: 1. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line). Page 15 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 L2 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average No. Frequency Remark reading reading factor result result limit limit margin margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 1* 0.1544 37.30 24.66 10.15 47.45 34.81 65.76 55.76 -18.31 -20.95 Pass 2 0.2329 33.84 20.88 10.17 44.01 31.05 62.35 52.35 -18.34 -21.30 Pass 3 0.5478 26.47 15.81 10.14 36.61 25.95 56.00 46.00 -19.39 -20.05 Pass 4 1.1722 26.07 13.06 10.27 36.34 23.33 56.00 46.00 -19.66 -22.67 Pass 5 1.7193 25.88 11.62 10.47 36.35 22.09 56.00 46.00 -19.65 -23.91 Pass 6 2.1881 25.00 10.31 10.61 35.61 20.92 56.00 46.00 -20.39 -25.08 Pass Note: 1. L1 = Line One (Live Line) / L2 = Line Two (Neutral Line). Page 16 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 7 RADIATED EMISSION MEASUREMENT 7.1. LIMITS OF RADIATED EMISSION MEASUREMENT Below 1GHz (for digital device) dBuV/m (At 10m) FREQUENCY (MHz) Class A Class B 30 ~ 230 40 30 230 ~ 1000 47 37 Limit tables for non-digital device: Class A Radiated Emission limit at 10m (for others) Frequency Field Strength Limit Field Strength Limit (MHZ) (uV/m)Q.P. (dBuV/m)Q.P. 30 - 88 90 39 88 - 216 150 43.5 216 – 960 210 46.4 Above 960 300 49.5 Class B Radiated Emission limit at 3m (for others) Frequency Field Strength Limit Field Strength Limit (MHZ) (uV/m)Q.P. (dBuV/m)Q.P. 30 - 88 100 40 88 - 216 150 43.5 216 – 960 200 46 Above 960 500 54 Above 1GHz(for all device) Frequency Class A (dBuV/m) (At 10m) Class B (dBuV/m) (At 3m) (MHZ) Average Peak Average Peak Above 1000 49.5 69.5 54 74 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) Emission level (dBuV/m) = 20 log Emission level (uV/m). (3) The measurement above 1GHz is at close-in distances 3m,and determine the limit L2 corresponding to the close-in distance d2 by applying the following relation: L2 = L1 (d1/d2), where L1 is the specified limit in microvolts per metre (uV/m) at the distance d1 (10m), L2 is the new limit for distance d2 (3m). So the new Class A limit above 1GHz at 3m is as following table: Page 17 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Frequency Class A (dBuV/m) (At 3m) (MHZ) Average Peak Above 1000 60 80 According to FCC Part 15.33 (b), for an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the Upper frequency of measurement range device or on which the device operates or (MHz) tunes (MHz) Below 1.75 30 1.75-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Page 18 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 7.2. TEST INSTRUMENTS See list of test equipment of this test report. 7.3. TEST PROCEDURES Procedure of Preliminary Test z The equipment was set up as per the test configuration to simulate typical usage per the user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which is placed on the ground plane. When the EUT is a floor standing equipment, it is placed on the ground plane which has a 12 mm non-conductive covering to insulate the EUT from the ground plane. z Support equipment, if needed, was placed as per ANSI C63.4. z All I/O cables were positioned to simulate typical usage as per ANSI C63.4. z The EUT received AC 120VAC/60Hz power source from the outlet socket under the turntable. All support equipment power received from another socket under the turntable. z The antenna was placed at 3 or 10 meter away from the EUT as stated in ANSI C63.4. The antenna connected to the Spectrum Analyzer via a cable and at times a pre-amplifier would be used. z The Analyzer / Receiver quickly scanned from 30MHz to 40GHz. The EUT test program was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. z Set the spectrum analyzer/ Receiver in the following setting as: Below 1GHz: RBW=100kHz / VBW=100kHz / Sweep=AUTO Above 1GHz: Peak: RBW=VBW=1MHz / Sweep=AUTO Average: RBW=1MHz / VBW=10Hz / Sweep=AUTO z The test mode(s) described in Item 3.1 were scanned during the preliminary test: z After the preliminary scan, we found the test mode described in Item 3.1 producing the highest emission level. z The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test. Page 19 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Procedure of Final Test z EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test. z The Analyzer / Receiver scanned from 30MHz to 40GHz. Emissions were scanned and measured rotating the EUT to 360 degrees, varying cable placement and positioning the antenna 1 or 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. z Recording at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. Below 1GHz the Q.P. reading and above 1GHz the Peak and Average reading are presented. z The test data of the worst-case condition(s) was recorded. Page 20 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 7.4. TEST SETUP Below 1 GHz . Above 1 GHz z For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. Page 21 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 7.5. DATA SAMPLE Frequency Reading Correct Result Limit Margin Height Degree Remark (MHz) (dBuV) Factor (dBuV/m) (dBuV/m) (dB) (cm) (°) (dB/m) x.xx 37.04 -14.00 23.04 30.00 -6.96 300 40 peak Freq. = Emission frequency in MHz Reading = Uncorrected Analyzer/Receiver reading Correct Factor = Antenna Factor + Cable Loss - Amplifier Gain Result = Reading + Factor Limit = Limit stated in standard Margin = Reading in reference to limit Height = Height of antenna Degree = Position of turn table Remark = Information of value (Peak/ QuasiPeak/Average) Calculation Formula Margin (dB) = Result (dBuV/m) – Limit (dBuV/m) Page 22 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 7.6. TEST RESULTS Below 1GHz Model No. K105 Test Mode Mode 2 Environmental 26deg.C, 78% RH, 1010hPa 6dB Bandwidth 100 kHz Conditions Antenna Pole Vertical Antenna Distance 3m Detector Function Quasi-peak. Tested by Star Standard FCC CLASS B No. Frequency Reading Correct Result Limit Margin Height Degree Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) (deg.) 1 30.0000 30.41 1.87 32.28 40.00 -7.72 100 42 peak 2 45.5200 45.07 -8.78 36.29 40.00 -3.71 100 319 peak 3 59.1000 46.53 -11.47 35.06 40.00 -4.94 100 10 peak 4 88.2000 44.70 -11.30 33.40 43.50 -10.10 100 168 peak 5 229.8200 38.07 -6.44 31.63 46.00 -14.37 100 290 peak 6 960.2300 26.85 8.07 34.92 54.00 -19.08 100 286 peak Note: 1. The other emission levels were very low against the limit. Page 23 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Model No. K105 Test Mode Mode 2 Environmental 26deg.C, 78% RH, 1010hPa 6dB Bandwidth 100 kHz Conditions Antenna Pole Horizontal Antenna Distance 3m Detector Function Quasi-peak. Tested by Star Standard FCC CLASS B No. Frequency Reading Correct Result Limit Margin Height Degree Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) (deg.) 1 30.0000 28.20 1.87 30.07 40.00 -9.93 100 229 peak 2 59.1000 41.13 -11.47 29.66 40.00 -10.34 100 114 peak 3 88.2000 45.06 -11.30 33.76 43.50 -9.74 100 0 peak 4 335.5500 36.22 -3.02 33.20 46.00 -12.80 100 111 peak 5 358.8300 32.49 -2.36 30.13 46.00 -15.87 100 158 peak 6 960.2300 27.50 8.07 35.57 54.00 -18.43 100 210 peak Note: 1. The other emission levels were very low against the limit. Page 24 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Above 1GHz Model No. K105 Test Mode Mode 2 Environmental 26deg.C, 78% RH, 1010hPa 6dB Bandwidth 1 MHz Conditions Antenna Pole Vertical Antenna Distance 3m Detector Function Peak or average. Tested by Star Standard FCC CLASS B No. Frequency Reading Correct Result Limit Margin Height Degree Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) (°) 1 1434.870 50.40 -10.37 40.03 74.00 -33.97 100 126 peak 2 1434.870 39.44 -10.37 29.07 54.00 -24.93 100 103 AVG 3 2991.984 48.96 -5.88 43.08 74.00 -30.92 100 133 peak 4 2991.984 32.86 -5.88 26.98 54.00 -27.02 100 152 AVG 5 6667.335 48.84 0.07 48.91 74.00 -25.09 100 299 peak 6 6667.335 30.98 0.07 31.05 54.00 -22.95 100 316 AVG Note: 1. The other emission levels were very low against the limit. Above 1GHz Page 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 Model No. K105 Test Mode Mode 2 Environmental 26deg.C, 78% RH, 1010hPa 6dB Bandwidth 1 MHz Conditions Antenna Pole Horizontal Antenna Distance 3m Detector Function Peak or average. Tested by Star Standard FCC CLASS B No. Frequency Reading Correct Result Limit Margin Height Degree Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) (°) 1 2052.104 55.53 -9.01 46.52 74.00 -27.48 100 129 peak 2 2052.104 37.82 -9.01 28.81 54.00 -25.19 100 120 AVG 3 2991.984 50.51 -5.88 44.63 74.00 -29.37 100 256 peak 4 2991.984 36.07 -5.88 30.19 54.00 -23.81 100 244 AVG 5 6456.914 50.85 -0.70 50.15 74.00 -23.85 100 38 peak 6 6456.914 30.47 -0.70 29.77 54.00 -24.23 100 13 AVG Note: 1. The other emission levels were very low against the limit. Page 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Page 27 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: KS110407B01-EF FCC ID: ZFT-K105 Date of Issue: April 14, 2011 RADIATED EMISSION TEST Page 28 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.


Document Created: 2011-04-20 10:55:03
Document Modified: 2011-04-20 10:55:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC