MPE Report

FCC ID: ZCB620GB

RF Exposure Info

Download: PDF
FCCID_2769180

RF EXPOSURE TEST FCC ID: ZCB620GB Applied procedures / limit These devices are not exempted from compliance does not exceed the Commission’s RF exposure guidelines. Unless a device operates at substantially low power levels, with a low gain antenna(s), supporting information is generally needed to establish the various potential operating configurations and exposure conditions of a transmitter and its antenna(s) in order to determine compliance with the RF exposure guidelines. In order to demonstrate compliance with MPE requirement(see Section 2.1091),the following information is typically needed: Calculation that estimates the minimum separation distance (20 cm or more) between an antenna and persons required to satisfy power density limits defined for free space. Antenna installation and device operating instructions for installers(professional/unskilled users),and the parties responsible for ensuring compliance with the RF exposure requirement Any caution statements and/or warming labels that are necessary in order to comply with the exposure limits Any other RF exposure related issues that may affect MPE compliance. FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency(RF) radiation as specified in 1.1307(b). (A) Limits for Occupational / Controlled Exposure Electric Field Magnetic Field Averaging Time Frequency Power Density (S) Strength (E) Strength (H) |E|2,|H|2or S Range (MHz) (mW/ cm2) (V/m) (A/m) (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Electric Field Magnetic Field Averaging Time Frequency Power Density (S) Strength (E) Strength (H) |E|2,|H|2 or S Range (MHz) (mW/ cm2) (V/m) (A/m) (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density

MPE CALCULATION METHOD Calculation Method of RF Safety Distance: P :power input to the antenna in Mw EIRP :Equivalent(effective) isotropic radiated power. S :power density mW/ cm2 G ;numeric gain of antenna relative to isotropic radiator R :distance to centre of radiation in cm FCC radio frequency exposure limits may be exceeded at distances closer than r cm from the antenna of this device EIRP=10(Antenna Gain+Peak Output Power/10) Note: 1. s=1.0 mW /cm2 for limits for General Population/Uncontrolled Exposures. 2. The time averaged power over 30 minutes will be equaled Output Power. 3. The Power Density at a distance of 20cm calculated from the formula is far below the limit of 1MW/ cm2

TEST RESULTS Maximum Peak Output power Antenna Limit of Conducted Distance Power Density Channel to antenna Gain 2 Power Density Result Output Power (cm) (mW/ cm ) (mW) (numeric) (mW/ cm2) (dBm) 802.11b 3dBi 2412MHz 14.92 31.046 20 0.012 1 Pass (1.995) 3dBi 2437MHz 14.83 30.409 20 0.012 1 Pass (1.995) 3dBi 2462MHz 14.75 29.854 20 0.012 1 Pass (1.995) 802.11g 3dBi 2412MHz 13.94 24.774 (1.995) 20 0.01 1 Pass 3dBi 2437MHz 13.73 23.605 (1.995) 20 0.009 1 Pass 3dBi 2462MHz 13.13 20.559 (1.995) 20 0.008 1 Pass 802.11n20 3dBi 2412MHz 12.16 16.444 (1.995) 20 0.007 1 Pass 3dBi 2437MHz 12.33 17.1 (1.995) 20 0.007 1 Pass 3dBi 2462MHz 12.49 17.742 (1.995) 20 0.007 1 Pass 802.11n40 3dBi 2422MHz 11.07 12.794 (1.995) 20 0.005 1 Pass 3dBi 2437MHz 11.13 12.972 (1.995) 20 0.005 1 Pass 3dBi 2452MHz 11.16 13.062 (1.995) 20 0.005 1 Pass


Document Created: 2015-09-28 11:42:56
Document Modified: 2015-09-28 11:42:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC