Test Setup Photos

FCC ID: ZBCAC75H103

Test Setup Photos

Download: PDF
FCCID_4111208

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM181000899401 Fax: +86 (0) 755 2671 0594 Page: 1 of 15 Email: ee.shenzhen@sgs.com TEST REPORT Application No.: SZEM1810008994CR Applicant: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Applicant: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, Shenzhen, China Manufacturer: SHENZHEN DNS INDUSTRIES CO., LTD. Address of Manufacturer: 23/F Building A, Shenzhen International Innovation Center, No.1006 Shennan Road, Futian, Shenzhen, China Factory: HUIZHOU D&S CABLE CO., LTD. Address of Factory: LONGJIN DONGJIANG INDUSTRY ZONE, SHUIKOU, HUICHENG, HUIZHOU, GUANGDONG, CHINA Equipment Under Test (EUT): EUT Name: WIRELESS CHARGER Model No.: AC75H103 Trade mark: DNS, omars, novoo FCC ID: ZBCAC75H103 Standard(s) : 47 CFR Part 18 Date of Receipt: 2018-10-17 Date of Test: 2018-10-17 to 2018-10-23 Date of Issue: 2018-10-24 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Keny Xu EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 2 of 15 Revision Record Version Chapter Date Modifier Remark 01 2018-10-24 Original Authorized for issue by: Peter Geng /Project Engineer Eric Fu /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 3 of 15 2 Test Summary Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted 47 CFR Part 18 FCC MP-5 Part 18.307 Pass disturbance Radiated emission 47 CFR Part 18 FCC MP-5 Part 18.305 Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 4 of 15 3 Contents Page 1 COVER PAGE ............................................................................................................................................1 2 TEST SUMMARY .......................................................................................................................................3 3 CONTENTS ................................................................................................................................................4 4 GENERAL INFORMATION ........................................................................................................................5 4.1 DETAILS OF E.U.T. ...............................................................................................................................5 4.2 DESCRIPTION OF SUPPORT UNITS .........................................................................................................5 4.3 MEASUREMENT UNCERTAINTY ..............................................................................................................5 4.4 TEST LOCATION....................................................................................................................................6 4.5 TEST FACILITY......................................................................................................................................6 4.6 DEVIATION FROM STANDARDS ...............................................................................................................6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS .....................................................................................6 5 EQUIPMENT LIST ......................................................................................................................................7 6 RADIO SPECTRUM MATTER TEST RESULTS .......................................................................................8 6.1 CONDUCTED DISTURBANCE ...................................................................................................................8 6.1.1 E.U.T. Operation ............................................................................................................................8 6.1.2 Test Setup Diagram .......................................................................................................................8 6.1.3 Measurement Procedure and Data...............................................................................................8 6.2 RADIATED EMISSION ...........................................................................................................................11 6.2.1 E.U.T. Operation ..........................................................................................................................12 6.2.2 Test Setup Diagram .....................................................................................................................12 6.2.3 Measurement Procedure and Data.............................................................................................12 7 PHOTOGRAPHS ......................................................................................................................................15 7.1 TEST SETUP .......................................................................................................................................15 7.2 EUT CONSTRUCTIONAL DETAILS (EUT PHOTOS).................................................................................15 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 5 of 15 4 General Information 4.1 Details of E.U.T. Power supply: Input: DC 5V, 3A Output 1: DC 5V, 1A Output 2: DC 5V, 1A Cable: USB to DC charging line: 100cm, unshielded Operation frequency: 109.29-184.29kHz Modulation type: Load modulation Antenna type: Inductive Loop Coil Antenna Remark: This device has been tested the worst status of full load and the device has been tested with mobile phone at zero charge, intermediate charge, and full charge. 4.2 Description of Support Units Description Manufacturer Model No. Serial No. provided by AC/DC adapter CD122 N/A client(UGREEN) iPhone 8 Apple A1863 F4GVQ656JC6D Mobile Phone SAMSUNG SM-G9500 R28J9140LPB 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency ± 7.25 x 10-8 2 Duty cycle ± 0.37% 3 Occupied Bandwidth ± 3% 4 RF conducted power ± 0.75dB 5 RF power density ± 2.84dB 6 Conducted Spurious emissions ± 0.75dB ± 4.5dB (below 1GHz) 7 RF Radiated power ± 4.8dB (above 1GHz) ± 4.5dB (Below 1GHz) 8 Radiated Spurious emission test ± 4.8dB (Above 1GHz) 9 Temperature test ± 1°C 10 Humidity test ± 3% 11 Supply voltages ± 1.5% 12 Time ± 3% This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 6 of 15 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. IC#: 4620C. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 7 of 15 5 Equipment List Conducted disturbance Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shielding Room ChangZhou ZhongYu GB-88 SEM001-06 2017-05-10 2020-05-09 Measurement Software AUDIX e3 V5.4.1221d N/A N/A N/A Coaxial Cable SGS N/A SEM024-01 2018-07-12 2019-07-11 LISN Rohde & Schwarz ENV216 SEM007-01 2018-09-25 2019-09-24 LISN ETS-LINDGREN 3816/2 SEM007-02 2018-04-02 2019-04-01 EMI Test Receiver Rohde & Schwarz ESCI SEM004-02 2018-04-02 2019-04-01 Radiated emission Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27 Coaxial Cable SGS N/A SEM029-01 2018-07-12 2019-07-11 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2018-04-02 2019-04-01 (9kHz-7GHz) Trilog-Broadband Schwarzbeck VULB9168 SEM003-18 2016-01-26 2019-01-25 Antenna(25MHz-2GHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2018-04-13 2019-04-12 Co Active Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-03 2018-09-27 2019-09-26 Indicator Industry Factory Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-04 2018-09-27 2019-09-26 Indicator Industry Factory Humidity/ Temperature Mingle N/A SEM002-08 2018-09-27 2019-09-26 Indicator Changchun Barometer Meteorological DYM3 SEM002-01 2018-04-08 2019-04-07 Industry Factory This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 8 of 15 6 Radio Spectrum Matter Test Results 6.1 Conducted disturbance Test Requirement Part 18.307 Test Method: FCC MP-5 Limit: 6.1.1 E.U.T. Operation Operating Environment: Temperature: 24.3 °C Humidity: 63.5 % RH Atmospheric Pressure: 1010 mbar Pretest these a:Charge mode_Keep the EUT charging(5W) modes to find b: Charge mode_Keep the EUT charging(10W) the worst case: The worst case b: Charge mode_Keep the EUT charging(10W) for final test: 6.1.2 Test Setup Diagram 6.1.3 Measurement Procedure and Data This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 9 of 15 Mode:b; Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 10 of 15 Mode:b; Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 11 of 15 6.2 Radiated emission Test Requirement Part 18.305 Test Method: FCC MP-5 Measurement Distance: 3m Limit: 1Field strength may not exceed 10 µV/m at 1600 meters. Consumer equipment operating below 1000 MHz is not permitted the increase in field strength otherwise permitted here for power over 500 watts. 2Reduced to the greatest extent possible. 3Field strength may not exceed 10 µV/m at 1600 meters. Consumer equipment is not permitted the increase in field strength otherwise permitted here for over 500 watts. 4Induction cooking ranges manufactured prior to February 1, 1980, shall be subject to the field strength limits for miscellaneous ISM equipment. Remark: 1 This product belongs to non-ISM equipment, the field strength limit is 15uV/m at 300 meter distance. 2 Limit: 20log(15uV/m) +20log (300/3) =23.52+40=63.52dBuV/m at 3 meters distance This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 12 of 15 6.2.1 E.U.T. Operation Operating Environment: Temperature: 25 °C Humidity: 51 % RH Atmospheric Pressure: 1010 mbar Pretest these a:Charge mode_Keep the EUT charging(5W) modes to find b: Charge mode_Keep the EUT charging(10W) the worst case: The worst case b: Charge mode_Keep the EUT charging(10W) for final test: 6.2.2 Test Setup Diagram 6.2.3 Measurement Procedure and Data This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 13 of 15 Mode b: 9kHz-150kHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 14 of 15 Mode b: 150kHz-30MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM181000899401 Page: 15 of 15 7 Photographs 7.1 Test Setup Please refer to setup photos. 7.2 EUT Constructional Details (EUT Photos) Please Refer to external and internal photos for details. - End of the Report - This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-11-28 06:02:23
Document Modified: 2018-11-28 06:02:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC