Module Approval Request

FCC ID: ZAT26M1

Cover Letter(s)

Download: PDF
FCCID_3087554

            telefication                                                                                        RF_734_02
—Ii2—                                                                                                          04 April 16


Modular Approval Request FCC (KDB 996369 D01 & Part 15.212)

FCC ID: _ZAT26M1__

Items to be covered by Single modular transmitters.                                          Answerfrom applicant
1.    The modular transmitter must have its own RF shielding.                                YES, Please refer to External
                                                                                              Photos.
2.    The modular transmitter must have buffered modulation/data inputs (if such inputs      Yes, U1 CC2650 is used for
      are provided) to ensure that the module will comply with Part 15 requirements           this function
      under conditions of excessive data rates or over—modulation.
3.    The modular transmitter must haveits own power supply regulation.                      Yes, the U1 and L1, C8 is the
                                                                                              DC to DC power regulation.
4.    The modular transmitter must comply with the antenna requirements of Section           Yes, there is a chip antenna
      15.203 and 15.204(b)(c). The antenna must either be permanently attached or             soldered in the module.
      employ a "unique" antenna coupler (at all connections between the module and the
      antenna, including the cable).

 5.   The modular transmitter must be tested in a stand—alone configuration, i.e., the       Yes, the module is tested in a
      module must not be inside another device during testing. This is intended to            stand—alone configuration as
      demonstrate that the module is capable of complying with Part 15 emission limits       the test photos show.
      regardless of the device into which it is eventually installed.

6.    The modular transmitter must be equipped with either a permanently affixed label       YES, please refer to the
      or must be capable of electronically displaying its FCC identification number in        exhibition label sample for
      accordance with 15.212 (a)(1)(vi)(A) / (B).                                             this module.

7.    The modular transmitter must comply with any specific rule or operating                YES, please refer to the user
      requirements applicable to the transmitter and the manufacturer must provide            manual.
      adequate instructions along with the module to explain any such requirements. A
      copy of these instructions must be included in the application for equipment
      authorization. For example, there are very strict operational and timing
      requirements that must be met before a transmitter is authorized for operation under
      Section 15.231. For instance, data transmission is prohibited, except for operation
      under Section 15.231(c), in which case there are separate field strength level and
      timing requirements. Compliance with these requirements must be assured.

8.    The modular transmitter must comply with any applicable RF exposure                    YES, RF exposure statement
      requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and            is attached in the user
      specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and             manual.
       15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices
      perform routine environmental evaluation for RF Exposure to demonstrate
      compliance. In addition, spread spectrum transmitters operating under Section
      15.247 are required to address RF Exposure compliance. Modular transmitters
      approved under other Sections of Part 15, when necessary, may also need to
      address certain RF Exposure concerns, typically by providing specific
      installation and operating instructions for users, installers and other interested
      parties to ensure compliance.




                                                                                                                    x


             telefication                                                                                     RF_734_02
—i3—                                                                                                         04 April 16

 Items to be covered by Split_modular transmitters.                                            Answerfrom applicant
 1:   The modular transmitter must comply with all requirements of a single modular
      transmitter except for items (1) & (5) of the above single modular approval
      requirements.

      Only the radio front end must be shielded. The physical crystal and tuning
      capacitors may be located external to the shielded radio elements. The interface
      between the split sections of the modular system must be digital with a minimum
      signalling amplitude of 150 mV peak—to—peak.

      Control information and other data may be exchanged between the transmitter
      control elements and radio front end.

      The sections of a split modular transmitter must be tested installed in a host
      device(s) similar to that which is representative ofthe platform(s) intended for use.

      Manufacturers must ensure that only transmitter control elements and radio front
      end components that have been approved together are capable of operating together.
      The transmitter module must not operate unless it has verified that the installed
      transmitter control elements and radio front end have been authorized together.
      Manufacturers may use means including, but not limited to, coding in hardware and
      electronic signatures in software to meet these requirements, and must describe the
      methods in their application for equipment authorization.




Note: A limited modular approval (LMA) may be granted for single or split modular transmitters
that comply partially with the requirements above.




Name and surname of applicant (or authorized representative): _/Mag                                    ines __
                                                                                           [
                                                                                       /
Date: :J?u(‘) — 88— e|                                           Signature:           Lt ?          C



Document Created: 2016-08-02 15:11:24
Document Modified: 2016-08-02 15:11:24

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC