Test Report

FCC ID: YZZGRP2616

Test Report

Download: PDF
FCCID_4433898

Page 34 of 116 Report No.: 190708003RFC-4 IEEE 802.11ac-VHT80 Channel 42 Channel 58 Channel 106 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 35 of 116 Report No.: 190708003RFC-4 5.4 6 DB BANDWIDTH & OCCUPIED BANDWIDTH FCC 47 CFR Part 15 Subpart E Section 15.407 (e) Test Requirement: RSS-247 Issue 2 Section 6.2.4.1 Test Method: KDB 789033 D02 v02r01 Section C.2 Limit: Within the 5.725-5.85 GHz band, the minimum 6 dB bandwidth of U-NII devices shall be at least 500 kHz. Test Procedure: The output from the transmitter was connected to an attenuator and then to the input of the RF Spectrum Analyzer. Spectrum analyzer according to the following Settings: a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) ≥ 3 * RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.5.3 for details. Instruments Used: Refer to section 3 for details Test Mode: Transmitter mode Test Results: Pass Test Data: Channel/ 6 dB 99% 6 dB Mode Frequency Bandwidth Bandwidth Bandwidth Pass / Fail (MHz) (MHz) (MHz) Limit 149 (5745) 16.34 16.574 > 500 kHz Pass IEEE 802.11a 157 (5785) 16.34 16.583 > 500 kHz Pass 165 (5825) 16.32 16.543 > 500 kHz Pass 149 (5745) 17.32 17.732 > 500 kHz Pass IEEE 802.11n-HT20 157 (5785) 17.20 17.708 > 500 kHz Pass 165 (5825) 17.40 17.735 > 500 kHz Pass 151 (5755) 35.69 36.183 > 500 kHz Pass IEEE 802.11n-HT40 159 (5795) 35.73 36.182 > 500 kHz Pass 149 (5745) 17.56 17.728 > 500 kHz Pass IEEE 802.11ac-VHT20 157 (5785) 16.91 17.738 > 500 kHz Pass 165 (5825) 17.34 17.702 > 500 kHz Pass 151 (5755) 35.78 36.182 > 500 kHz Pass IEEE 802.11ac-VHT40 159 (5795) 36.05 36.204 > 500 kHz Pass IEEE 802.11ac-VHT80 155 (5775) 75.38 75.481 > 500 kHz Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 36 of 116 Report No.: 190708003RFC-4 The test plots as follows: IEEE 802.11a IEEE 802.11n-HT20 Channel 149 Channel 157 Channel 165 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 37 of 116 Report No.: 190708003RFC-4 IEEE 802.11n-HT40 Channel 151 Channel 159 IEEE 802.11ac-VHT20 Channel 149 Channel 157 Channel 165 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 38 of 116 Report No.: 190708003RFC-4 IEEE 802.11 ac-VHT40 Channel 151 Channel 159 IEEE 802.11ac-VHT80 Channel 155 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 39 of 116 Report No.: 190708003RFC-4 5.5 MAXIMUM CONDUCTED OUTPUT POWER OR E.I.R.P FCC 47 CFR Part 15 Subpart E Section 15.407 (a)(1)(2)(3) Test Requirement: RSS-247 Issue 2 Section 6.2.1.1/6.2.2.1/6.2.3.1/6.2.4.1 Test Method: KDB 789033 D02 v02r01 Section E.3.a (Method PM) Limits: FCC 47 CFR Part 15 Subpart E 1. For the band 5.15-5.25 GHz. (i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm). (ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. Fixed point-to-point U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding reduction in the maximum conducted output power or maximum power spectral density. For fixed point-to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in maximum conducted output power and maximum power spectral density is required for each 1 dB of antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to- point operations. (iv) For client devices in the 5.15-5.25 GHz band, the maximum conducted output power over the frequency band of operation shall not exceed 250 mW provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 2. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 3. For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 40 of 116 Report No.: 190708003RFC-4 Limits: RSS-247 Issue 2 1. Frequency band 5150-5250 MHz For OEM devices installed in vehicles, the maximum e.i.r.p. shall not exceed 30 mW or 1.76 + 10 log10B, dBm, whichever is less. Devices shall implement transmitter power control (TPC) in order to have the capability to operate at least 3 dB below the maximum permitted e.i.r.p. of 30 mW. For other devices, the maximum e.i.r.p. shall not exceed 200 mW or 10 + 10 log10B, dBm, whichever power is less. B is the 99% emission bandwidth in megahertz. The e.i.r.p. spectral density shall not exceed 10 dBm in any 1.0 MHz band. 2. Frequency band 5250-5350 MHz For OEM devices installed in vehicles, the maximum e.i.r.p. shall not exceed 30 mW or 1.76 + 10 log10B, dBm, whichever is less. Devices shall implement TPC in order to have the capability to operate at least 3 dB below the maximum permitted e.i.r.p. of 30 mW. Devices, other than devices installed in vehicles, shall comply with the following: a) The maximum conducted output power shall not exceed 250 mW or 11 + 10 log10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1.0 MHz band; b) The maximum e.i.r.p. shall not exceed 1.0 W or 17 + 10 log10B, dBm, whichever is less. B is the 99% emission bandwidth in megahertz. Note that devices with a maximum e.i.r.p. greater than 500 mW shall implement TPC in order to have the capability to operate at least 6 dB below the maximum permitted e.i.r.p. of 1 W. Additional requirements In addition to the above requirements, devices shall comply with the following, where applicable: a) Outdoor fixed devices with a maximum e.i.r.p. greater than 200 mW shall comply with the following e.i.r.p. at different elevations, where θ is the angle above the local horizontal plane (of the Earth) as shown below: i. -13 dBW/MHz for 0o≤ θ< 8o ii. -13 − 0.716 (θ-8) dBW/MHz for 8o ≤ θ< 40o iii. -35.9 − 1.22 (θ-40) dBW/MHz for 40o ≤ θ ≤45o iv. -42 dBW/MHz for θ > 45o The measurement procedure defined in Annex A of this document shall be used to verify the compliance to the e.i.r.p. at different elevations. b) Devices, other than outdoor fixed devices, having an e.i.r.p. greater than 200 mW shall comply with either i. or ii. below: i. devices shall comply with the e.i.r.p. elevation mask in 6.2.2.3(a); or ii. devices shall implement a method to permanently reduce their e.i.r.p. via a firmwarefeature in the event that the Department requires it. The test report must demonstratehow the device’s power table can be updated to meet this firmware requirement. Themanufacturer shall provide this firmware to update all systems automatically incompliance with the directions received from the Department. 3. Frequency bands 5470-5600 MHz and 5650-5725 MHz The maximum conducted output power shall not exceed 250 mW or 11 + 10 log 10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1.0 MHz band. The maximum e.i.r.p. shall not exceed 1.0 W or 17 + 10 log10B, dBm, whichever is less. B is the 99% emission bandwidth in megahertz. Note that devices with a maximum e.i.r.p. greater than 500 mW shall implement TPC in order to have the capability to operate at least 6 dB below the maximum permitted e.i.r.p. of 1 W. 4. Frequency band 5725-5850 MHz The maximum conducted output power shall not exceed 1 W. The output power spectral density shall not exceed 30 dBm in any 500 kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the output power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 41 of 116 Report No.: 190708003RFC-4 corresponding reduction in transmitter conducted power. Fixed point-to-point operations exclude the use of point-to-multipoint3 systems, omnidirectional applications and multiple collocated transmitters transmitting the same information. Test Procedure: 1. Connected the EUT’s antenna port to measure device by 10dB attenuator. 2. Method PM is used to perform output power measurement, trigger and gating function of wide band power meter is enabled to measure max output power of Tx on burst. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.5.3 for details. Instruments Used: Refer to section 3 for details Test Mode: Transmitter mode Test Results: Pass Test Data: Directional gain and the maximum output power limit. RSS-247 Issue 2 Frequency Band Antenna Gain (dBi)) Power Limits (dBm) U-NII-1 4 23.00 U-NII-2A 4 24.00 U-NII-2C 4 24.00 U-NII-3 4 30.00 FCC 47 CFR Part 15 Subpart E Frequency Band Antenna Gain (dBi)) Power Limits (dBm) U-NII-1 4 24.00 U-NII-2A 4 24.00 U-NII-2C 4 24.00 U-NII-3 4 30.00 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 42 of 116 Report No.: 190708003RFC-4 Frequency band 5150-5250 MHz RSS-247 Issue 2: For IEEE 802.11a, the minimum 99% emission bandwidth is 17.044MHz 10 dBm + 10log10 (17.044) = 22.32 dBm < 23 dBm So the 22.32 dB limit applicable For IEEE 802.11n-HT20/ ac-VHT20, the minimum 99% emission bandwidth is 18.036 MHz 10 dBm + 10log10 (18.036) = 22.56 dBm < 23 dBm So the 22.56 dB limit applicable For IEEE 802.11n-HT40/ ac-VHT40/ ac-VHT80, the minimum 99% emission bandwidth is 36.408 MHz 10 dBm + 10log10 (36.408) = 25.61 dBm > 23 dBm So the 23 dB limit applicable Channel/ Maximum e.i.r.p Limit Mode Pass / Fail Frequency (MHz) (dBm) (dBm) 36 (5180) 20.27 22.32 Pass IEEE 802.11a 44 (5220) 20.21 22.32 Pass 48 (5240) 20.18 22.32 Pass 36 (5180) 20.05 22.56 Pass IEEE 802.11n-HT20 44 (5220) 20.11 22.56 Pass 48 (5240) 19.82 22.56 Pass 38 (5190) 19.91 23 Pass IEEE 802.11n-HT40 46 (5230) 19.9 23 Pass 36 (5180) 20.03 22.56 Pass IEEE 802.11ac-VHT20 44 (5220) 20.09 22.56 Pass 48 (5240) 19.91 22.56 Pass 38 (5190) 19.95 23 Pass IEEE 802.11ac-VHT40 46 (5230) 19.89 23 Pass IEEE 802.11ac-VHT80 42 (5210) 19.74 23 Pass Remark: 1. Maximum e.i.r.p = Maximum conducted output power + Antenna Gain Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 43 of 116 Report No.: 190708003RFC-4 FCC 47 CFR Part 15 Subpart E: Channel/ Maximum conducted output Limit Mode Frequency power (dBm) Pass / Fail (dBm) (MHz) Meas Power Corr’d Power 36 (5180) 16.14 16.27 24 Pass IEEE 802.11a 44 (5220) 16.08 16.21 24 Pass 48 (5240) 16.05 16.18 24 Pass 36 (5180) 15.91 16.05 24 Pass IEEE 802.11n-HT20 44 (5220) 15.97 16.11 24 Pass 48 (5240) 15.68 15.82 24 Pass 38 (5190) 15.64 15.91 24 Pass IEEE 802.11n-HT40 46 (5230) 15.63 15.90 24 Pass 36 (5180) 15.89 16.03 24 Pass IEEE 802.11ac- 44 (5220) 15.95 16.09 24 Pass VHT20 48 (5240) 15.77 15.91 24 Pass IEEE 802.11ac- 38 (5190) 15.68 15.95 24 Pass VHT40 46 (5230) 15.62 15.89 24 Pass IEEE 802.11ac- 42 (5210) 15.22 15.74 24 Pass VHT80 Remark: 1. Corr’d Power = Meas Power + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 44 of 116 Report No.: 190708003RFC-4 Frequency band 5250-5350 MHz RSS-247 Issue 2: For IEEE 802.11 a, the minimum 99% emission bandwidth is 17.077 MHz 11 dBm + 10log10 (17.077) = 23.32 dBm < 24dBm So the 23.32 dB limit applicable For IEEE 802.11n-HT20/ ac-VHT20, the minimum 99% emission bandwidth is 17.999 MHz 11 dBm + 10log10 (17.999) = 23.55 dBm < 24dBm So the 23.55 dB limit applicable For IEEE 802.11 n-HT40/ac-VHT40/ac-VHT80, the minimum 99% emission bandwidth is 36.364 MHz 11 dBm + 10log10 (36.364) = 26.60 dBm > 24 dBm (200mW) So the 24 dB limit applicable FCC 47 CFR Part 15 Subpart E: For IEEE 802.11 a/n/ac, the minimum 26 dB emission bandwidth is 22.50 MHz 11 dBm + 10log10 (25.50) = 24.52 dBm > 24 dBm (200mW) So the 24 dB limit applicable Maximum conducted output Channel/ Limit (dBm) power (dBm) Pass / Mode Frequency FCC Part RSS-247 Fail (MHz) Meas Power Corr’d Power 15E 52 (5260) 16.11 16.24 24 23.32 Pass IEEE 802.11a 60 (5300) 15.92 16.05 24 23.32 Pass 64 (5320) 15.99 16.12 24 23.32 Pass 52 (5260) 15.88 16.02 24 23.55 Pass IEEE 802.11n- 60 (5300) 15.57 15.71 24 23.55 Pass HT20 64 (5320) 15.66 15.80 24 23.55 Pass IEEE 802.11n- 54 (5270) 15.56 15.83 24 24 Pass HT40 62 (5310) 14.45 14.72 24 24 Pass 52 (5260) 15.63 15.77 24 23.55 Pass IEEE 802.11ac- 60 (5300) 15.58 15.72 24 23.55 Pass VHT20 64 (5320) 15.39 15.53 24 23.55 Pass IEEE 802.11ac- 54 (5270) 15.60 15.87 24 24 Pass VHT40 62 (5310) 14.36 14.63 24 24 Pass IEEE 802.11ac- 58 (5290) 14.89 15.41 24 24 Pass VHT80 Remark: 1. Maximum conducted output power = Conducted output power + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 45 of 116 Report No.: 190708003RFC-4 Frequency bands 5470-5725 MHz (RSS-247 Issue 2 Not including 5600-5650 MHz) RSS-247 Issue 2: For IEEE 802.11 a, the minimum 99% emission bandwidth is 17.048 MHz 11 dBm + 10log10 (17.048) = 23.32 dBm < 24 dBm So the 23.32 dB limit applicable For IEEE 802.11n-HT20/ac-VHT20, the minimum 99% emission bandwidth is 18.011 MHz 11 dBm + 10log10 (18.011) = 23.56 dBm < 24 dBm So the 23.56 dB limit applicable For IEEE 802.11 n-HT40/ac-VHT40/ac-VHT80, the minimum 99% emission bandwidth is 36.370 MHz 11 dBm + 10log10 (36.370) = 26.61 dBm > 24 dBm So the 24 dB limit applicable FCC 47 CFR Part 15 Subpart E: For IEEE 802.11 a/n/ac, the minimum 26 dB emission bandwidth is 21.40 MHz 11 dBm + 10log10 (21.40) = 24.30 dBm > 24 dBm So the 24 dB limit applicable Maximum conducted output Channel/ power (dBm) Limit (dBm) Pass / Mode Frequency SISO Fail (MHz) FCC Part RSS-247 Meas Power Corr’d Power 15E 100 (5500) 15.67 15.80 24 23.30 Pass IEEE 802.11a 116 (5580) 15.39 15.52 24 23.30 Pass 140 (5700) 14.17 14.30 24 23.30 Pass 100 (5500) 15.14 15.28 24 23.55 Pass IEEE 802.11n- 116 (5580) 14.87 15.01 24 23.55 Pass HT20 140 (5700) 13.83 13.97 24 23.55 Pass 102 (5510) 15.15 15.42 24 24 Pass IEEE 802.11n- 110 (5550) 15.14 15.41 24 24 Pass HT40 134 (5670) 14.15 14.42 24 24 Pass 100 (5500) 15.26 15.40 24 23.55 Pass IEEE 802.11ac- 116 (5580) 15.00 15.14 24 23.55 Pass VHT20 140 (5700) 14.00 14.14 24 23.55 Pass 102 (5510) 15.25 15.52 24 24 Pass IEEE 802.11ac- 110 (5550) 15.21 15.48 24 24 Pass VHT40 134 (5670) 14.05 14.32 24 24 Pass IEEE 802.11ac- 106 (5530) 14.64 15.16 24 24 Pass VHT80 Remark: 1. Maximum conducted output power = Conducted output power + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 46 of 116 Report No.: 190708003RFC-4 Frequency band 5725-5850 MHz Maximum conducted output Channel/ power (dBm) Limit Pass / Mode Frequency (MHz) (dBm) Fail Meas Power Corr’d Power 149 (5745) 14.93 15.06 30 Pass IEEE 802.11a 157 (5785) 15.10 15.23 30 Pass 165 (5825) 15.37 15.50 30 Pass 149 (5745) 14.55 14.69 30 Pass IEEE 802.11n-HT20 157 (5785) 14.41 14.55 30 Pass 165 (5825) 14.99 15.13 30 Pass 151 (5755) 14.56 14.83 30 Pass IEEE 802.11n-HT40 159 (5795) 14.73 15.00 30 Pass 149 (5745) 14.69 14.83 30 Pass IEEE 802.11ac-VHT20 157 (5785) 14.75 14.89 30 Pass 165 (5825) 15.09 15.23 30 Pass 151 (5755) 14.62 14.89 30 Pass IEEE 802.11ac-VHT40 159 (5795) 14.79 15.06 30 Pass IEEE 802.11ac-VHT80 155 (5775) 13.95 14.47 30 Pass Remark: 1. Maximum conducted output power = Conducted output power + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 47 of 116 Report No.: 190708003RFC-4 5.6 PEAK POWER SPECTRAL DENSITY FCC 47 CFR Part 15 Subpart E Section 15.407 (a)(1)(2)(3) Test Requirement: RSS-247 Issue 2 Section 6.2.1.1/6.2.2.1/6.2.3.1/6.2.4.1 Test Method: KDB 789033 D02 v02r01 Section F Limits: FCC 47 CFR Part 15 Subpart E 1. For the band 5.15-5.25 GHz. (i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm). (ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. Fixed point-to-point U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding reduction in the maximum conducted output power or maximum power spectral density. For fixed point-to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in maximum conducted output power and maximum power spectral density is required for each 1 dB of antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to- point operations. (iv) For client devices in the 5.15-5.25 GHz band, the maximum conducted output power over the frequency band of operation shall not exceed 250 mW provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 2. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 3. For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 48 of 116 Report No.: 190708003RFC-4 Limits: RSS-247 Issue 2 1. Frequency band 5150-5250 MHz For OEM devices installed in vehicles, the maximum e.i.r.p. shall not exceed 30 mW or 1.76 + 10 log 10B, dBm, whichever is less. Devices shall implement transmitter power control (TPC) in order to have the capability to operate at least 3 dB below the maximum permitted e.i.r.p. of 30 mW. For other devices, the maximum e.i.r.p. shall not exceed 200 mW or 10 + 10 log10B, dBm, whichever power is less. B is the 99% emission bandwidth in megahertz. The e.i.r.p. spectral density shall not exceed 10 dBm in any 1.0 MHz band. 2. Frequency band 5250-5350 MHz For OEM devices installed in vehicles, the maximum e.i.r.p. shall not exceed 30 mW or 1.76 + 10 log10B, dBm, whichever is less. Devices shall implement TPC in order to have the capability to operate at least 3 dB below the maximum permitted e.i.r.p. of 30 mW. Devices, other than devices installed in vehicles, shall comply with the following: a) The maximum conducted output power shall not exceed 250 mW or 11 + 10 log10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1.0 MHz band; b) The maximum e.i.r.p. shall not exceed 1.0 W or 17 + 10 log10B, dBm, whichever is less. B is the 99% emission bandwidth in megahertz. Note that devices with a maximum e.i.r.p. greater than 500 mW shall implement TPC in order to have the capability to operate at least 6 dB below the maximum permitted e.i.r.p. of 1 W. Additional requirements In addition to the above requirements, devices shall comply with the following, where applicable: a) Outdoor fixed devices with a maximum e.i.r.p. greater than 200 mW shall comply with the following e.i.r.p. at different elevations, where θ is the angle above the local horizontal plane (of the Earth) as shown below: i. -13 dBW/MHz for 0o≤ θ< 8o ii. -13 − 0.716 (θ-8) dBW/MHz for 8o ≤ θ< 40o iii. -35.9 − 1.22 (θ-40) dBW/MHz for 40o ≤ θ ≤45o iv. -42 dBW/MHz for θ > 45o The measurement procedure defined in Annex A of this document shall be used to verify the compliance to the e.i.r.p. at different elevations. b) Devices, other than outdoor fixed devices, having an e.i.r.p. greater than 200 mW shall comply with either i. or ii. below: iii. devices shall comply with the e.i.r.p. elevation mask in 6.2.2.3(a); or iv. devices shall implement a method to permanently reduce their e.i.r.p. via a firmwarefeature in the event that the Department requires it. The test report must demonstratehow the device’s power table can be updated to meet this firmware requirement. Themanufacturer shall provide this firmware to update all systems automatically incompliance with the directions received from the Department. 3. Frequency bands 5470-5600 MHz and 5650-5725 MHz The maximum conducted output power shall not exceed 250 mW or 11 + 10 log 10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1.0 MHz band. The maximum e.i.r.p. shall not exceed 1.0 W or 17 + 10 log10B, dBm, whichever is less. B is the 99% emission bandwidth in megahertz. Note that devices with a maximum e.i.r.p. greater than 500 mW shall implement TPC in order to have the capability to operate at least 6 dB below the maximum permitted e.i.r.p. of 1 W. 4. Frequency band 5725-5850 MHz The maximum conducted output power shall not exceed 1 W. The output power spectral density shall not exceed 30 dBm in any 500 kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the output power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 49 of 116 Report No.: 190708003RFC-4 corresponding reduction in transmitter conducted power. Fixed point-to-point operations exclude the use of point-to-multipoint3 systems, omnidirectional applications and multiple collocated transmitters transmitting the same information. Test Procedure: The output from the transmitter was connected to an attenuator and then to the input of the RF Spectrum Analyzer. Spectrum analyzer according to the following Settings: 1. For U-NII-1, U-NII-2A, U-NII-2C band: Using method SA-2 a) Set span to encompass the entire emission bandwidth (EBW) of the signal. b) Set RBW = 1 MHz, Set VBW ≥ 3 RBW, Detector = RMS c) Sweep time = auto, trigger set to “free run”. d) Trace average at least 100 traces in power averaging mode. e) Record the max value and add 10 log (1/duty cycle) 2. For U-NII-3 band: a) Set span to encompass the entire emission bandwidth (EBW) of the signal. b) Set RBW = 500 kHz, Set VBW ≥ 3 RBW, Detector = RMS c) Use the peak marker function to determine the maximum power level in any 500 kHz band segment within the fundamental EBW. d) Sweep time = auto, trigger set to “free run”. e) Trace average at least 100 traces in power averaging mode. f) Record the max value and add 10 log (1/duty cycle) Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.5.3 for details. Instruments Used: Refer to section 3 for details Test Mode: Transmitter mode Test Results: Pass Test Data: Directional gain and the maximum output power limit. RSS-247 Issue 2: PSD Limits (dBm/MHz or Frequency Band Antenna Gain (dBi)) dBm/500kHz) U-NII-1 4 10.00 U-NII-2A 4 11.00 U-NII-2C 4 11.00 U-NII-3 4 30.00 FCC 47 CFR Part 15 Subpart E: PSD Limits (dBm/MHz or Frequency Band Antenna Gain (dBi)) dBm/500kHz) U-NII-1 4 11.00 U-NII-2A 4 11.00 U-NII-2C 4 11.00 U-NII-3 4 30.00 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 50 of 116 Report No.: 190708003RFC-4 Frequency band 5150-5250 MHz RSS-247 Issue 2 Channel/ Frequency e.i.r.p. spectral Limit Pass / Mode (MHz) density (dBm/MHz) (dBm/MHz) Fail 36 (5180) 7.71 10 Pass IEEE 802.11a 44 (5220) 7.35 10 Pass 48 (5240) 7.28 10 Pass 36 (5180) 7.12 10 Pass IEEE 802.11n-HT20 44 (5220) 7.18 10 Pass 48 (5240) 6.62 10 Pass 38 (5190) 5.80 10 Pass IEEE 802.11n-HT40 46 (5230) 5.89 10 Pass 36 (5180) 6.99 10 Pass IEEE 802.11ac-VHT20 44 (5220) 6.71 10 Pass 48 (5240) 6.50 10 Pass 38 (5190) 6.08 10 Pass IEEE 802.11ac-VHT40 46 (5230) 5.91 10 Pass IEEE 802.11ac-VHT80 42 (5210) 2.97 10 Pass Remark: 1. e.i.r.p. spectral density = Power spectral density + Duty Cycle Factor + Antenna Gain FCC 47 CFR Part 15 Subpart E Channel/ Power spectral density Limit Pass / Mode Frequency (dBm/MHz) (dBm/MHz) Fail (MHz) Meas PSD Corr’d PSD 36 (5180) 3.577 3.71 11 Pass IEEE 802.11a 44 (5220) 3.218 3.35 11 Pass 48 (5240) 3.151 3.28 11 Pass 36 (5180) 2.975 3.12 11 Pass IEEE 802.11n-HT20 44 (5220) 3.039 3.18 11 Pass 48 (5240) 2.475 2.62 11 Pass 38 (5190) 1.529 1.80 11 Pass IEEE 802.11n-HT40 46 (5230) 1.613 1.89 11 Pass 36 (5180) 2.854 2.99 11 Pass IEEE 802.11ac-VHT20 44 (5220) 2.570 2.71 11 Pass 48 (5240) 2.365 2.50 11 Pass 38 (5190) 1.816 2.08 11 Pass IEEE 802.11ac-VHT40 46 (5230) 1.646 1.91 11 Pass IEEE 802.11ac-VHT80 42 (5210) -1.554 -1.03 11 Pass Remark: 1. Power spectral density = Conducted power spectral density + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 51 of 116 Report No.: 190708003RFC-4 Frequency band 5250-5350 MHz Channel/ Power spectral density Limit Pass / Mode Frequency (dBm/MHz) (dBm/MHz) Fail (MHz) Meas PSD Corr’d PSD 52 (5260) 2.814 2.95 11 Pass IEEE 802.11a 60 (5300) 2.539 2.67 11 Pass 64 (5320) 2.809 2.94 11 Pass 52 (5260) 2.897 3.04 11 Pass IEEE 802.11n-HT20 60 (5300) 2.145 2.29 11 Pass 64 (5320) 2.513 2.66 11 Pass 54 (5270) 1.222 1.50 11 Pass IEEE 802.11n-HT40 62 (5310) 0.167 0.44 11 Pass 52 (5260) 2.254 2.39 11 Pass IEEE 802.11ac-VHT20 60 (5300) 2.057 2.19 11 Pass 64 (5320) 2.313 2.45 11 Pass 54 (5270) 1.197 1.46 11 Pass IEEE 802.11ac-VHT40 62 (5310) 0.320 0.59 11 Pass IEEE 802.11ac-VHT80 58 (5290) -1.958 -1.43 11 Pass Remark: 1. Power spectral density = Conducted power spectral density + Duty Cycle Factor Frequency bands 5470-5725 MHz (RSS-247 Issue 2 Not including 5600-5650 MHz) Channel/ Power spectral density Limit Pass / Mode Frequency (dBm/MHz) (dBm/MHz) Fail (MHz) Meas PSD Corr’d PSD 100 (5500) 3.212 3.34 11 Pass IEEE 802.11a 116 (5580) 3.056 3.19 11 Pass 140 (5700) 1.939 2.07 11 Pass 100 (5500) 2.844 2.99 11 Pass IEEE 802.11n-HT20 116 (5580) 2.928 3.07 11 Pass 140 (5700) 1.761 1.90 11 Pass 102 (5510) 1.732 2.01 11 Pass IEEE 802.11n-HT40 110 (5550) 1.286 1.56 11 Pass 134 (5670) 0.778 1.05 11 Pass 100 (5500) 2.705 2.84 11 Pass IEEE 802.11ac- 116 (5580) 2.664 2.80 11 Pass VHT20 140 (5700) 1.494 1.63 11 Pass 102 (5510) 1.795 2.06 11 Pass IEEE 802.11ac- 110 (5550) 1.853 2.12 11 Pass VHT40 134 (5670) 0.346 0.61 11 Pass IEEE 802.11ac- 106 (5530) -1.919 -1.39 11 Pass VHT80 Remark: 1. Power spectral density = Conducted power spectral density + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 52 of 116 Report No.: 190708003RFC-4 Frequency band 5725-5850 MHz Channel/ Power spectral density Limit Pass / Mode Frequency (dBm/500kHz) (dBm/500KHz) Fail (MHz) Meas PSD Corr’d PSD 149 (5745) 0.127 0.26 30 Pass IEEE 802.11a 157 (5785) -0.364 -0.23 30 Pass 165 (5825) 0.225 0.36 30 Pass 149 (5745) -0.678 -0.53 30 Pass IEEE 802.11n-HT20 157 (5785) -0.557 -0.41 30 Pass 165 (5825) -0.050 0.09 30 Pass 151 (5755) -2.536 -2.26 30 Pass IEEE 802.11n-HT40 159 (5795) -2.003 -1.73 30 Pass 149 (5745) -0.521 -0.38 30 Pass IEEE 802.11ac- 157 (5785) -0.396 -0.26 30 Pass VHT20 165 (5825) -0.052 0.08 30 Pass IEEE 802.11ac- 151 (5755) -2.199 -1.93 30 Pass VHT40 159 (5795) -1.770 -1.50 30 Pass IEEE 802.11ac- 155 (5775) -5.591 -5.07 30 Pass VHT80 Remark: 1. Power spectral density = Conducted power spectral density + Duty Cycle Factor Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 53 of 116 Report No.: 190708003RFC-4 The test plots as follows: IEEE 802.11a IEEE 802.11n-HT20 Channel 36 Channel 44 Channel 48 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 54 of 116 Report No.: 190708003RFC-4 IEEE 802.11a IEEE 802.11n-HT20 Channel 52 Channel 60 Channel 64 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 55 of 116 Report No.: 190708003RFC-4 IEEE 802.11a IEEE 802.11n-HT20 Channel 100 Channel 116 Channel 140 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 56 of 116 Report No.: 190708003RFC-4 IEEE 802.11a IEEE 802.11n-HT20 Channel 149 Channel 157 Channel 165 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 57 of 116 Report No.: 190708003RFC-4 IEEE 802.11n-HT40 Channel 38 Channel 46 Channel 54 Channel 62 Channel 102 Channel 110 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 58 of 116 Report No.: 190708003RFC-4 IEEE 802.11n-HT40 Channel 134 Channel 151 Channel 159 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 59 of 116 Report No.: 190708003RFC-4 IEEE 802.11ac-VHT20 IEEE 802.11ac-VHT40 Channel 36 Channel 38 Channel 44 / Channel 48 Channel 46 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com


Document Created: 2019-09-07 10:33:02
Document Modified: 2019-09-07 10:33:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC