Users Manual

FCC ID: YZP-REBETZ37E

Users Manual

Download: PDF
FCCID_4088081

41248]| 24 3.7" 3—color Graphic type ESL User manual Copyright©. 2018. All Rights Reserved. @ LGOJ4—4!!

1. Overview CJ2]4] 23 = Remote control device provides customer with several functions as below / Waking Tag up from sleep mode v Updating new purchase image on Tag v Deleting purchase image on Tag v Returning a Tag to be factory settings Display Area Profile Hook Battery Cover @LG Innotek deounc ut s iemcreno wany Webiecoorfa mmnew w mm n nowe sn w voume on a on ns mealue mum wea se moretrowe wraey c mamow A remote controller or a NFC Device contact point for communication. = Remo—con description «_ LED : One of any buttons is pushed, red led turns on. 0@ After sending some data to a Tag, red led will turn off. Registration : Updating New Purchase Information on Tag = Release : Deleting Purchase Information on Tag Reset : Returning a Tag to be factory settings E = = Keep Alive : Waking Tag up from sleep mode Copyright©. 2018. All Rights Reserved. @ LGO|t—4!!

2. Updating new purchase image on Tag Clglb] 28 C & J m ¢—C C 1 To change purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag‘s display 2. Press and hold ‘Registration‘ button on remote controller until Red LED off (about 0.5 seconds) 3. When Tag is successfully received ‘Registration‘ data from remote controller, Tag‘s display will be changed to "Connected" for a few minutes. That means Tag hides purchase image to read Tag‘s IEEE MAC address through the Barcode scanner. 4. In NMS Client, download new purchase image to the Tag in registration status When image downloading is finished successfully, Tag‘s display will be changed to new purchase image Casel) If image downloading is failed, Tag‘s display will be changed to "Busy". After "Alive Time", this Tag will be download new purchase image again Copyright©. 2018. All Rights Reserved. @ LGO|—4!!

3. Deleting purchase information on Tag C124] 23 ‘,)V\S/ 0\0 Eis o esm t Wrive *\af 7,900. e C & J ho To release(delete) purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Release‘ button until red LED off (about 0.5 seconds) 3. If Tag was received ‘Reset‘ command from remote controller, Tag will delete purchase information and Tag‘s display will be changed to "Ready" 4. After step.3, Tag goes to deep sleep mode and doesn‘t communicate with gateway until receiving ‘Keep Alive‘ or ‘Registration‘ data from remote controller Copyright©. 2018. All Rights Reserved. @ LGOJ4—4!!

4. Waking Tag up CI2]4] 28 0\0 es ts fes ol E) be oi 0\0 es ts hss ol E) be e rve CS 7,900 pRclooe zoo ow ME NE moaoo WNIE NE Wine BRed _~.«. 1 cA éi «. $109 e ||||n::|:::;l:;‘|l:::l‘;| ( To wake Tag up from sleep mode, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Keep Alive‘ button until Red LED off (about 0.5 seconds) 3. Tag will wake up and goes to next step. It‘s depends on connection information with gateway casel) If this Tag wasn‘t connected with a gateway before sleep mode, go to 4—1 case?) If this Tag was connected with a gateway before sleep mode, go to 4—2 4—1. Searching gateway and goes to the next step. it‘s depends on searching results casel) If Tag was successfully connected, Tag‘s display will be changed to "Ready" case?) If Tag wasn‘t connected, Tag‘s display(may be "Ready") will be refreshed 4—2. Sending ‘Keep Alive‘ packet to gateway and Tag will go to sleep mode again casel) If Tag was received response from gateway, this Tag will go to "sleep mode" until the specified time in gateway. After "sleep mode", this Tag will send "Keep Alive" Packet to gateway again. case?) If Tag wasn‘t received response from Gateway, this Tag will retry three times. After that, Tag‘s display will be changed to "Disconnected". Also this Tag will perform a whole channel scan every five minutes. Copyright©. 2018. All Rights Reserved. @ LGOJ4—4!!

5. Returning a Tag to be factory settings Clglb] 28 m Cc XAS 7,900 — 2 2016.10.20 14:34:59 mon ow IRINE NE 353,003 To make a Tag to be factory reset status, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Reset‘ button until Red LED off (about 0.5 seconds) 3. If Tag was received ‘Reset‘ command from remote controller, Tag goes back to factory settings and Tag‘s display will be changed to "Ready" After step.3, Tag goes to deep sleep mode and doesn‘t communicate with gateway until receiving ‘Keep Alive‘ or ‘Registration‘ data from remote controller casel) If Tag was received "Keep Alive" or "Registration" command from remote controller, this Tag will perform a whole channel scan. case?) If Tag was received "Reset" or "Release" command from remote controller, Tag‘s display will be changed to "Ready" again Copyright©. 2018. All Rights Reserved. @ LGOJ4—4!!

6. Tag status Cl94] 23 Symbol Mode Image C (IJ _2 Deep Sleep Mode Connected with Gateway =§ q7 Disconnected with Gateway ~— OJ Battery discharge (the battery needs to be replaced) I'L__T.I Image download Failure("Busy") Copyright©. 2018. All Rights Reserved. @1LG°==

Regulation Information Trade name: Manufacturer: LG Innotek Co., Ltd. (Jangduk-dong) 26, Hanamsandan 5beon-ro, Gwangsan-gu, Gwangju, 62229, Korea Model name: REBE-TZ37E, REBE-TZ37F Operating frequency: 2405 MHz ~ 2480 MHz for Zigbee, 13.56 MHz for NFC (Receiving only) Maximum transmit power: 10 dBm for Zigbee Can be contacted via website: www.lginnotek.com FCC Compliance Statement (for products subject to Part 15) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirement. CE RF Radiation Exposure Statement Caution: This equipment complies with European RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. EU Representative LG Innotek Co., Ltd. Am Limespark 2 (Innovapark) 65843 Sulzbach am Taunus, Germany

@ LG Innotek A24 47} 34 I-IUI-A‘IJHJI-% uEO C u_ X I—Ql Arg E‘ISI : IIlOl_lr_E‘ll ( ) 7lAR| 44 : e%A34 #y7i7i(PAdioleSAIAARe 4417]7]) 240 : REBE—TZ37E, REBE—TZ37F AIZA 4 A1Z37} : 4x]0| S (4) / §t—t 41249 :4180 45 £7] QIE¥H# : R—C—LGW—REBE—TZ37E — 2A AfQF : IEEE 802.15.4 (Zighee) — A8ZIfA : 2402 MHz ~ 2480 MHz (Zigbee), 13.56 MHz (NFC) —Al34 :16 71 — 343 : 10 mW/MHz O| 6t E 7 |*le §#Ol84¥#81014 ¢!%]246 20 n O|4| A—8 6t&+ 7| *t}O)=& SAR 4| C|¥27|AHM & 250 SaRn AlgiStI o 91 7l?l€ 7144 (B€) UA 49717124 #2 218014 AS stt l8 4402 s{0], Z2E 140¥ 8 & 4 464C


Document Created: 2018-08-27 20:51:24
Document Modified: 2018-08-27 20:51:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC