User Manaual

FCC ID: YZP-REBEMZ42A

Users Manual

Download: PDF
FCCID_2619941

2015.04.19 ELS 4.2 Mono Graphic Type Manual Ver. 0.1

1. ELS Description & Key Function «Remote control device provides customer with several functions as below ¥ Waking Tag up from sleep mode ¥— Updating new purchase image on Tag ¥ Deleting purchase image on Tag ¥ Returning a Tag to be factory settings C#> Display Area Lt Profile Hook aaasaass1sasss s u sy y Battery Cover Apple Juice296ml $7.99 IMll! Zigi: sc «Remo—con description l Registration LED : One of any buttons is pushed, green led turs on. After sending some data to a Tag, green led will turn off. | Release Registration : Updating New Purchase Information on Tag | { Keep Alve Release : Deleting Purchase Information on Tag Reset : Returning a Tag to be factory settings Keep Alive : Waking Tag up from sleep mode @LG Innot« : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user‘s authority to operate the equipment. This appliance and its antenna must not be co—ocated or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cn must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. LGOJ—4 74

2. "Registration" Key Function Ready Connected I. BeB » UEctt d To change purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag‘s display 2. Press and hold ‘Registration‘ button on remote controller until green LED off (about 0.5 seconds) 3. When Tag is successfully received ‘Registration‘ data from remote controller, Tag‘s display will be changed to "Connected" for a few minutes. That means Tag hides purchase image to read Tag‘s IEEE MAC address through the Barcode scanner In NMS Client, download new purchase image to the Tag in registration status When image downloading is finished successfully, Tag‘s display will be changed to new purchase image Copyright©. 2015. All Rights Reserved. @ LGOIEEEJI

3. "Release" Key Function EEcpvse Ready $7 ® 9 9 » I Bn M Zoisoir sotenn To release(delete) purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Release‘ button until green LED off (about 0.5 seconds) 3. If Tag was received ‘Reset‘ command from remote controller, Tag will delete purchase information and Tag‘s display will be changed to "Ready" 4. After step.3, Tag goes to deep sleep mode and doesn‘t communicate with gateway until receiving ‘Keep Alive‘ or ‘Registration‘ data from remote controller Disconnect Ie mm Copyright©. 2015. All Rights Reserved. @ LGOIEEEJI

4. "Keep Alive" Key Function Case 1 Ready Ready ino n ino n Case 2 F | Connected t: inen n Case 3 Apple Juice 296m $7.99 |hss To wake Tag up from sleep mode, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Keep Alive‘ button until green LED off (about 0.5 seconds) 3. Tag will wake up and goes to next step. It‘s depends on connection information with gateway case1) If this Tag wasn‘t connected with a gateway before sleep mode, go to 4—1 case2) If this Tag was connected with a gateway before sleep mode, go to 4—2 4—1. Searching gateway and goes to the next step. it‘s depends on searching results case1) If Tag was successfully connected, Tag‘s display will be changed to "Ready" case?) If Tag wasn‘t connected, Tag‘s display(may be "Ready") will be refreshed 4—2. Sending ‘Keep Alive‘ packet to gateway and Tag will go to sleep mode again Copyright©. 2015. All Rights Reserved. @ LGOIEEEJI

5. "Reset" Key Function Eym Ready $7.99 ® uoo unn mnn I"IIII“ 20150101 Juice 20150101 $0.02/ml To make a Tag to be factory reset status, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold ‘Reset‘ button until green LED off (about 0.5 seconds) 3. If Tag was received ‘Reset‘ command from remote controller, Tag goes back to factory settings and Tag‘s display will be changed to "Ready" 4. After step.3, Tag goes to deep sleep mode and doesn‘t communicate with gateway until receiving ‘Keep Alive‘ or ‘Registration‘ data from remote controller Copyright©. 2015. All Rights Reserved. @ LGOIEEEJI

6. Status Display Aluj at Ready Deep Sleep mode neott Connected Connected to gateway L Disconnect Disconnected to gateway nomm Image downloading fail Busy No Battery Battery is dis—charged (to need changing battery) ncetd Copyright©. 2015. All Rights Reserved. @ LGOIEEEJI


Document Created: 2015-05-19 10:39:35
Document Modified: 2015-05-19 10:39:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC