Manual

FCC ID: YZP-REAXXOXXA

Users Manual

Download: PDF
FCCID_3270575

Confidential LG Innotek ESL Tag Controller User manual Copyright®. 2015. All Rights Reserved. @ LGOIiE—iI

Confidential 1. Overview LG Innotek = Tag controller device provides customer with several functions as below Display Area ¥~— Waking Tag up from sleep mode & Updating new purchase image on Tag _ Deleting purchase image on Tag & Returning a Tag to be factory settings J .. $109 é 9 Made In Italy o (7r. temact (r. temuct +550 +550 nmam a9n + nomam wan m = Tag Controller description I Tag Controller Symbol Mode Fucntion Match the Tag to Registration Merchandise‘s Info. Delete the Tag from Detete matched Info. Change the Next =P stored Image Function User Defined T7 * (ex. Stock Info.) x/ LED On while HF Signal transmitting / Buzzer beeps for 0.2s ¥* IF the voltage level is lower than 2.2V, it will warn to user by LED blinking Copyright®. 2015. All Rights Reserved. @©Laoi==

Confidential 2. Updating new purchase image on Tag LG innotek C 4 J —GT— 2. J To change purchase information on Tag, perform the following steps : 1. Put Tag controller near center of Tag‘s display Press and hold ‘Registration‘ button on Tag controller until red LED off (about 0.5 seconds) 3. When Tag is successfully received ‘Registration‘ data from Tag controller, Tag‘s display will be changed to "Connected" for a few minutes. That means Tag hides purchase image to read Tag‘s IEEE MAC address through the Barcode scanner. 4. In NMS Client, download new purchase image to the Tag in registration status When image downloading is finished successfully, Tag‘s display will be changed to new purchase image Case1) If image downloading is failed, Tag‘s display will be changed to "Busy". After "Alive Time", this Tag will be download new purchase image again @La9==

Confidential 3. Deleting purchase information on Tag LG innotek Red Wine _« J _ $109| mp C 4 J ! g Made In: Italy uld 2. & To release(delete) purchase information on Tag, perform the following steps : 1. Put Tag controller near center of Tag display Press and hold ‘Release‘ button until red LED off (about 0.5 seconds) 3. If Tag was received ‘Reset‘ command from Tag controller, Tag will delete purchase information and Tag‘s display will be changed to "Ready" 4. After step.3, Tag goes to deep sleep mode and doesn‘t communicate with gateway until receiving ‘Keep Alive‘ or ‘Registration‘ data from Tag controller Copyright©. 2015. All Rights Reserved. @ LGOJ—4

Confidential 4. Change Next Image LG Innotek Be(l Will(‘ 100 and Be(l Wm(' 100 ant iél ... $109 mp ié$109 } 9 JnmatHit 9 JndenA rertA 2. b To change the another saved image of Tag from former image, perform the following steps : 1. Put Tag controller near center of Tag display Press and hold ‘Next‘ button until red LED off (about 0.5 seconds) 3. If Tag was received ‘Next‘ command from Tag controller, Tag‘s display will be changed to new image Copyright©. 2015. All Rights Reserved. @ LGOI&-E—'I

Confidential 5. Spare Button LG Innotek This button is spare function. Customer will assign this button for their needs. For example stock function, etc. Copyright©. 2015. All Rights Reserved. @ LGOIEEE—"I

Confidential LG Innotek FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 14. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user‘s authority to operate the equipment. @©Laoi==


Document Created: 2017-01-18 15:05:03
Document Modified: 2017-01-18 15:05:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC