RF Exposure Info 2

FCC ID: YY3-01120709267

RF Exposure Info

Download: PDF
FCCID_1464513

APPENDIX B: BV ADT SAR MEASUREMENT SYSTEM

APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION

APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION D1: PHANTOM

Schmid & Partner Engineering AG s p e a g Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 1 245 9700, Fax +41 1 245 9779 info@speag.com, hittp://www.speag.com Certificate of Conformity / First Article Inspection Item Oval Flat Phantom EL1 4.0 Type No QD OVA 001B Series No 1003 and higher Manufacturer SPEAG Zeughausstrasse 43 CH—8004 Zurich Switzerland Tests Complete tests were made on the prototype units QD OVA 001 AA 1001, QD OVA 001 AB 1002, pre—series units QD OVA 001 BA 1003—1005 as well as on the series units QD OVA 001 BB, 1006 ff. Test Requirement Details Units tested Dimensions Compliant with the standard IEC Dimensions of bottom Prototypes, 62209 — 2 [1] requirements for 300 MHz — 6 GHz: Samples longitudinal = 600 mm (max. dimension) width= 400 mm (min dimension) depth= 190 mm Shape: ellipse Material thickness Compliant with the standard IEC Bottom plate: Prototypes, 62209 —— 2 [1] requirements 2.0mm +/ 0.2mm All items Material Dielectric parameters for required 300 MHz — 6 GHz Material parameters frequencies Rel. permittivity = 4 +/—1, sample Loss tangent s 0.05 Material resistivity The material has been tested to be DEGMBE based Equivalent compatible with the liquids defined in simulating liquids phantoms, the standards if handled and cleaned Material according to the instructions. sample Observe Technical Note for material compatibility. Sagging Compliant with the requirements <1% typical < 0.8% if Prototypes, according to the standard. filled with 155mm of Sample Sagging of the flat section when filled HSL900 and without testing with tissue simulating liquid DUT below Standards [1] EC 62209 — 2, Draft Version 0.9, "Evaluation of Human Exposure to Radio Frequency Fields from Handheld and Body—Mounted Wireless Communication Devices in the Frequency Range of 30 MHz to 6 GHz: Human models, Instrumentation and Procedures Part 2: Procedure to determine the Specific Absorption Rate (SAR) for ... including accessories and multiple transmitters", December 2004 Conformity Based on the sample tests above, we certify that this item is in compliance with the standard [1]. Date 07.07.2005 $ e__a 5chm%qAG Signature / Stamp Zoughasfstrasse 4378004 Z\Wfld/ f Phong 41 124 aArdis — info@speag.com, httpiiiwww.speag.com Doc No 881—QD OVA 001B—C Page 1(1)

D2: DOSIMETRIC E-FIELD PROBE

Calibration Laboratory of wyt9, loar Snrieedi ‘\\\/_/ 7 Schweizerischer Kalibrierdienst Schmid & Partner i\ia\Em{/é Service suisse d‘étalonnage Engineering AG Ls Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ’«/,////-_\T\\‘v‘ Swiss Calibration Service flls Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client BV—ADT (Auden) Certificate No: EX3—3504_Jan10 |CALIBRATION CERTIFICATE I Object EX3DV3 — SN:3504 Calibration procedure(s) QA CAL—01.v6, QA CAL—14.v3, QA CAL—23.v3 and QA CAL—25.v2 Calibration procedure for dosimetric E—field probes Calibration date: January 26, 2010 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards _ ID # _ Cal Date (Certificate No.) ___________ Scheduled Calibration ___| Power meter E44198 GB41293874 1—Apr—09 (No. 217—01030) Apr—10 Power sensor E4412A MY41495277 1—Apr—09 (No. 217—01030) Apr—10 Power sensor E4412A MY41498087 1—Apr—09 (No. 217—01030) Apr—10 | Reference 3 dB Aftenuator SN: $5054 (3c) 31—Mar—09 (No. 217—01026) Mar—10 | Reference 20 dB Attenuator SN: $5086 (20b) 31—Mar—09 (No. 217—01028) Mar—10 ‘ Reference 30 dB Attenuator SN: $5129 (30b) 31—Mar—09 (No. 217—01027) Mar—10 Reference Probe ES3DV2 SN: 3013 30—Dec—09 (No. ES3—3013_Dec08) Dec—10 DAE4 SN: 660 29—Sep—09 (No. DAE4—660_SepO9) Sep—10 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator HP 8648C US3642U01700 4—Aug—99 (in house check Oct—09) In house check: Oct—11 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—09) In house check: Oct10 Name Function Signature Calibrated by: KatJa Pokovic Technical Manager é;‘ Approved by: Fin Bomholt R&D Director —+—~/Z /%/ en y P—fa Issued: January 26, 2010 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: EX3—3504_Jan10 Page 1 of 11

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service ($AS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C modulation dependentlinearization parameters Polarization @ rotation around probe axis Polarization 9 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), Le., 9 = 0 is normal to probe axis Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "EEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) 1EC 62208—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Methods Applied and Interpretation of Parameters: * NORMx,y,z: Assessed for E—field polarization 9 = 0 (f s 900 MHz in TEM—cell; > 1800 MHz: R22 waveguide}. NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E*—field uncertainty inside TSL (see below ConvF). * NORM(Mx,y,2 = NORMx,y,2 * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. «_ DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. + Axy,2; Bxy,2; Cxy,2, VRxy,z: A, B, C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. * ConvF and Boundary Effect Parameters: Assessed in flat phantomn using E—field (or Temperature Transfer Standard for f< 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. * Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. * Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Certificate No: EX3—3504_Jan10 Page 2 of 11

EX3DV3 SN:3504 January 26, 2010 Probe EX3DV3 SN:3504 Manufactured: December 15, 2003 Last calibrated: January 21, 2009 Recalibrated: January 26, 2010 Calibrated for DASY Systems (Note: non—compatible with DASY2 system!) Certificate No: EX3—3504_Jan10 Page 3 of 11

EX3DV3 SN:3504 January 26, 2010 DASY — Parameters of Probe: EX3DV3 SN:3504 Basic Calibration Parameters Sensor X Sensor Y Sensor Z |Unc (k=2) Norm (uV/(V/im)")® 0.59 0.62 0.62 |+101% DCP (my)® 97.9 95.0 98.0 Modulation Calibration Parameters UID Communication System Name PAR A B C VR Unc® dB dBuV mV (k=2) 10000 CW 0.00 X 0.00 0.00 1.00| 300 # 1.5% Y 0.00 0.00 1.001 300 Z 0.00 0.00 1.00| 300 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of NormX,Y,Z do not affect the E—field uncertainty inside TSL (see Pages 5 and 6). * Numerical lingarization parameter: uncertainty not required & Uncertainty is determined using the maximum deviation from linear response applying recatangular distribution and is expressed for the square of the field value. Certificate No: EX3—3504_Jan10 Page 4 of 11

EX3DV3 SN:3504 January 26, 2010 DASY — Parameters of Probe: EX3DV3 SN:3504 Calibration Parameter Determined in Head Tissue Simulating Media f [MHz] Validity [MHz]® Permittivity Conductivity ConvF X ConvF Y__ ConvF 2 Alpha Depth Une (k=2) 900 * 50 /+ 100 41.5 4 5% 0.97 £ 5% 9.80 9.80 9.80 0.48 0.73 £11.0% 1750 £ 50 / £ 100 40.1 4 5% 1.37 4 5% 8.70 8.70 8.70 0.50 0.67 £11.0% 1950 * 50 / £ 100 40.0 4 5% 1.40 2 5% 8.20 8.20 8.20 0.38 0.75 £11.0% 2450 * 50 / £ 100 39.2 £ 5% 1.80 £ 5% 7.77 7.77 7.77 0.21 1.06 £11.0% 2600 * 50 / £ 100 39.0 £ 5% 1.96 £ 5% 7.79 7.19 7.79 0.22 116 £110% 5200 £ 50 /+ 100 36.0 + 5% 4.66 £ 5% 4.87 4.87 4.87 0.45 1.10 £13.1% 5300 £ 50 / £ 100 35.9 £ 5% 4.176 £ 5% 4.62 4.62 4.62 0.45 1.70 £13.1% 5500 * 50 / £ 100 35.6 £ 5% 4.96 # 5% 4.51 4.51 4.51 0.50 1.70 £13.1% 5600 £ 50 /# 100 35.5 £ 5% 5.07 £ 5% 4.25 4.25 4.25 0.55 1.70 £13.1% 5800 * 50 / 100 35.3 + 5% 5.27 £ 5% 4.53 4.53 4.53 0.50 1.70 £13.1% © The validity of + 100 MHz only applies for DASY v.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band Certificate No: EX3—3504_Jan10 Page 5 of 11

EX3DV3 SN:3504 January 26, 2010 DASY — Parameters of Probe: EX3DV3 SN:3504 Calibration Parameter Determined in Body Tissue Simulating Media f (MHz] Validity [MHz]C Permittivity Conductivity ConvFX ConvFY ConvF 2 Alpha Depth Unc (k=2) 900 # 50 /# 100 55.0 £ 5% 1.05 £ 5% 9.83 9.83 9.83 0.44 0.76 #11.0% 1750 £ 50 / £ 100 §3.4 £ 5% 1.49 £ 5% 8.64 8.64 8.64 0.44 0.74 #11.0% 1950 * 50 / £ 100 53.3 £ 5% 1.52 4 5% 8.52 8.52 8.52 0.39 0.79 #11.0% 2450 * 50 /« 100 §2.17 £ 5% 1.95 4 5% 7.91 7.91 7.91 0.32 0.86 #11.0% 2600 * 50 / 100 52.5 £ 5% 216 £ 5% 7.80 7.80 7.80 0.27 0.90 #11.0% 5200 * 50 / £ 100 49.0 4 5% 5.30 £ 5% 4.45 4.45 4.45 0.50 1.80 £13.1% 5300 * 50 / + 100 48.5 4 5% 542 + 5% 4.18 4.18 4.18 0.55 1.80 £13.1% §500 * 50 / 100 48.6 4 5% 5.65 x 5% 3.91 3.91 3.91 0.60 1.80 £13.1% 5600 * 50 / + 100 48.5 * 5% 5.77 # 5% 3.70 3.70 3.70 0.65 1.80 £13.1% 5800 £ 50 / £ 100 48.2 £5% 6.00 £ 5% 3.95 3.95 3.95 0.60 1.75 £181% ° The validity of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Certificate No: EX3—3504_Jan10 Page 6 of 11

EX3DV3 SN:3504 January 26, 2010 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) 15 1.4:; 13 Frequency response (normalized) 12 11 L 10 ; o.9 . 0.8 : 0.7 ; 0.6 : o.s | o 500 1000 1500 2000 2500 3000 f [MHz] —@—TEM ~@—R22 Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—3504_Jan10 Page 7 of 11

EX3DV3 SN:3504 January 26, 2010 Receiving Pattern (¢), 9 = 0° f = 600 MHz, TEM ifi110EXX f= 1800 MHz, WG R22 —O—30 MHz —BI— 100 MHz —@—600 MHz —IB— 1800 MHz —&—2500 MHz 0 60 120 240 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—3504_Jan10 Page 8 of 11

EX3DV3 SN:3504 January 26, 2010 Dynamic Range f(SARpesq) (Waveguide R22, f = 1800 MHz) 1.E+06 , 1.2+05 1.2+04 Input Signal [xV] 1.E+08 1.E+02 1.2+01 ; 1.E+00 0.0001 0.001 0.01 0.1 1 10 100 SAR [mW/cm‘] ~—@®—not compensated —®— compensated 0.01 0.1 1 10 SAR [mW/cm‘] Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—3504_Jan10 Page 9 of 11

EX3DV3 SN:3504 January 26, 2010 Conversion Factor Assessment f= 1750 MHz, WGLS R22 (head) SAR[mW/cm?] / W 3 o a o s30 ao 2 o 0 10 20 30 40 z[mm] | —@—Analytical —O—Measurements ‘ l —@— Analytical —O—Measurements | Deviation from Isotropy in HSL Error (¢, 9), f = 900 MHz 00 s g2: poese ornona 200620 beSrrE Error [dB] 266 BI—1.00—0.80 IMl—0.80——0.60 I—0.60——0.40 1—0.40——0.20 RI—0.20—0.00 ©10.00—0.20 m10.20—0.40 0.40—0.60 ©0.60—0.80 M0.80—1.00 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: EX3—3504_Jan10 Page 10 of 11

EX3DV3 SN:3504 January 26, 2010 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) Not applicable Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 2 mm Certificate No: EX3—3504_Jan10 Page 11 of 11

D3: DAE

Schmid & Partner Engineering AG s e a Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 44 245 9700, Fax +41 44 245 9779 info@speag.com, http://www.speag.com IMPORTANT NOTICE USAGE OF THE DAE 4 The DAE unit is a delicate, high precision instrument and requires careful treatment by the user. There are no serviceable parts inside the DAE. Special attention shall be given to the following points: Battery Exchange: The battery cover of the DAE4 unit is closed using a screw, over tightening the screw may cause the threads inside the DAE to wear out. Shipping of the DAE: Before shipping the DAE to SPEAG for calibration, remove the batteries and pack the DAE in an antistatic bag. This antistatic bag shall then be packed into a larger box or container which protects the DAE from impacts during transportation. The package shall be marked to indicate that a fragile instrument is inside. E—Stop Failures: Touch detection may be malfunctioning due to broken magnets in the E—stop. Rough handling of the E—stop may lead to damage of these magnets. Touch and collision errors are often caused by dust and dirt accumulated in the E—stop. To prevent Estop failure, the customer shall always mount the probe to the DAE carefully and keep the DAE unit in a non—dusty environmentif not used for measurements. Repair: Minor repairs are performed at no extra cost during the annual calibration. However, SPEAG reserves the right to charge for any repair especially if rough unprofessional handling caused the defect. DASY Configuration Files: Since the exact values of the DAE input resistances, as measured during the calibration procedure of a DAE unit, are not used by the DASY software, a nominal value of 200 MOhm is given in the corresponding configurationfile. Important Note: Warranty and calibration is void if the DAE unit is disassembled partly or fully by the Customer. Important Note: Never attempt to grease or oil the E—stop assembly. Cleaning and readjusting of the E— stop assembly is allowed by certified SPEAG personnel only and is part of the annual calibration procedure. Important Note: To prevent damage of the DAE probe connector pins, use great care when installing the probe to the DAE. Carefully connect the probe with the connector notch oriented in the mating position. Avoid any rotational movement of the probe body versus the DAE while turning the locking nut of the connector. The same care shall be used when disconnecting the probe from the DAE. Schmid & Partner Engineering TN_BRO40315AD DAE4.doc 11.12.2009

& : o¥49p Calibration Laboratory Of \“\\t//,”’/ Schweizerischer Kalibrierdienst Schmid & Partner ;i\\_//l/;: Service suisse d‘étalonnage Engineering AG ://R > Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 'f/,l///—\\\ y Swiss Calibration Service alalAs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Certificate No: DAE4—861_Jan10 CALIBRATIONCERTIFICATE_ Object DAE4— SD 000 pod4 BJ — SN: 861 Calibration procedure(s) QA CAL-06 vi2 1. 10 ca brat|on‘rocedure orthe dataacqussn on Calibration date: January 22. 2010 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratoryfacility: environment temperature (22 « 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Cerfificate No.) Scheduled Calibration Keithiey Multimeter Type 2001 SN: 0810278 1—0ct—09 (No: 9055) Oct—10 Secondary Standards ID # Check Date (in house) Scheduled Check Calibrator Box V1.1 SE UMS 006 AB 1004 0§—Jun—09 (in house check} In house check: Jun—10 Name Function Signature Calibrated by: Ahdréa Guntli . . ‘Techhii: n Approved by: FinBomholt _\ [R&D Director _ 10 l e Issued: January 22, 2010 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4—861_Jan10 Page 1 of 5

Calibration Laboratory of ul2 Schweizerischer Kalibrierdienst Schmid & Partner ig:\%//;% Service suisse d‘étalonnage Engineering AG 7 n c Servizio svizzero di taratura . . 4w y a mean — Zeughausstrasse 43, 8004 Zurich, Switzerland ’f/,,/fi\\\\\* Swiss Calibration Service alalids Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. «_ Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. Input resistance: DAE input resistance at the connector, during internal auto—zeroing and during measurement. Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—861_Jan1O Page 2 of 5

DC Voitage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6AuV , full range = ~100...+300 mV Low Range: 1LSB = 61nV , full range = hase +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404.395 + 0.1% (k=2) 404.784 + 0.1% (k=2) 405.737 £ 0.1% (k=2) Low Range 4.01182 + 0.7% (k=2) 3.98893 + 0.7% (k=2) 4.01269 + 0.7% (k=2) Connector Angle Connector Angle to be used in DASY system 123.0°%%1° Certificate No: DAE4—861_Jan10 Page 3 of 5

Appendix 1. DC Voltage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X + Input 200003.4 —2.33 —0.00 Channel X + Input 19997.73 ~1.97 —0.01 Channel X — Input ~19999.33 1.07 —0.01 Channel Y + input 200002.5 216 —0.00 Channel Y + Input 19995.17 4.43 —0.02 Channel Y — Input 20000.88 —0.58 0.00 Channel Z + input 199999.9 —3.99 —0.00 Channel Z2 + Input 19995.97 ~3.48 —0.02 Channel Z — Input 20002.39 0.01 0.01 Low Range Reading (uV) Difference (V) Error (%) Channel X + Input 1999.9 —0.34 0.02 Channel X + Input 199.26 —0.64 —0.32 Channel X — input +200.72 —0.82 0.41 Channel Y + Input 1999.2 —0.72 —0.04 Channel Y + Input 198.82 —1.18 +0.59 Channel Y — input —201.63 ~1.83 0.92 Channel 2 + Input 2001.1 1.22 0.06 Channel 2 + Input 197.99 —2.01 ~1.01 Channel Z — Input —201,59 —1.79 0.89 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (1V) Average Reading (V) Channel X 200 5.69 4.19 +200 —2.41 —3.99 Channel Y 200 1.24 1.40 ~200 +2.48 ~2.38 Channel Z 200 9. 16 —9.25 — 200 8.58 8.07 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 see Input Voltage (mV) Channel X (uV) Channel Y (V) Channel Z (uV) Channel X 200 — 2.32 1.39 Channel Y 200 1.89 — 4.20 Channel Z 200 1.32 0.19 — Certificate No: DAE4—861_Jan10 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15980 16853 Channel Y 16068 14547 Channel Z 16088 17866 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10M Average (uV) min. Offset (uV) max. Offset (uv) 5* [():\‘,’;a“m Channel X 0.16 —1.64 1.60 0.66 Channel Y +0.58 ~2.29 0.44 0.49 Channel Z —1.24 ~3.18 0.50 0.68 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance Zeroing (MOhm) Measuring (MOhm) Channel X 0.1999 199.8 Channel Y 0.2000 201.8 Channel Z 0.1999 199.7 8. Low Battery Alarm Voltage (verified during pre test) Typical values Alarm Level (VDC) Supply (+ Vec) +7.9 Supply (— Vec) —7.6 9. Power Consumption (verified during pre test) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vec) +0.0 +6 +14 Supply (— Vec) —0.01 —8 —9g Certificate No: DAE4—861_Jan10 Page 5 of 5

D4: SYSTEM VALIDATION DIPOLE

4 4 «ul Um Calibration Laboratory of Cs/s Schweizerischer Kalibrierdienst . gst Schmid & Partner iia%il/(&}é Service suisse d‘étalonnage Engineering AG J ids Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 41/,////-3\\\\3 Swiss Calibration Service Ahilals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client ADT (Auden) Certificate No: D835V2—4d021_Apr10 [CALIBRATION CERTIFICATE Object D835V2 — SN: 40021 Calibration procedure(s) QA CAL—O5.v7 Calibration procedure for dipole validation kits Calibration date: April 29, 2010 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE criticalfor calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 06—Oct—09 (No. 217—01086) Oct—10 Power sensor HP 8481A US37202783 06—Oct—09 (No. 217—01086) Oct—10 Reference 20 dB Attenuator SN: 5086 (20g) 30—Mar—10 (No. 217—01158) Mar—11 Type—N mismatch combination SN: 5047.2 / 06327 30—Mar—10 (No. 217—01162) Mar—11 Reference Probe ESSDV3 SN: 3205 26—Jun—09 (No. ES3—3205_Jun09) Jun—10 DAE4 SN: 601 02—Mar—10 (No. DAE4—601_Mar10) Mar—11 Secondary Standards ID # Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house check Oct—09) In house check: Oct—11 RF generator R&S SMT—06 100005 4—Aug—99 (in house check Oct—09) In house check: Oct—11 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—09) In house check: Oct—10 Name Function Signature C Calibrated by: Dimcelliev Laboratory Technician TeMss Approved by: KatJa Pokovic Technical Manager Issued: April 29, 2010 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D835V2—4d021_Apr10 Page 1 of 9

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. & SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. Certificate No: D835V2—4d021_Apr10 Page 2 of 9

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V5.2 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V4.9 Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 835 MHz &1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 # 0.2) °C 41.8 x 6 % 0.89 mho/m + 6 % Head TSL temperature during test (22.0 + 0.2) °C SAR result with Head TSL SAR averaged over 1 em* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.37 mW /g SAR normalized normalized to 1W 9.48 mW / g SAR for nominal Head TSL parameters normalized to 1W 9.58 mW /g « 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 1.55 mWw /g SAR normalized normalized to 1W 6.20 mW /g SAR for nominal Head TSL parameters normalized to 1W 6.24 mW ig * 16.5 % (k=2) Certificate No: D835V2—44021_Apr10 Page 3 of 9

Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.2 0.97 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 54.9 * 6 % 0.99 mho/m + 6 % Body TSL temperature during test (22.0 + 0.2) °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 2.52 mW / g SAR normalized normalized to 1W 10.1 mWw /g SAR for nominal Body TSL parameters normalized to 1W 9.91 mW / g # 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 1.65 mWw /g SAR normalized normalized to 1W 6.60 mWw /g SAR for nominal Body TSL parameters normalized to 1W 6.52 mW / g #16.5 % (k=2) Certificate No: DB35V2—4d021_Apr10 Page 4 of 9

Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 51.5 Q —2.5 |Q Return Loss — 31.0 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 48.1 Q — 3.9 jQ Return Loss —27.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.392 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on April 22, 2004 Certificate No: D835V2—4d021_Apr10 Page 5 of 9

DASY5 Validation Report for Head TSL Date/Time: 21.04.2010 10:38:05 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:4d021 Communication System: CW; Frequency: 835 MHz; Duty Cycle: 1: 1 Medium: H$L900 Medium parameters used: f = 835 MHz; 0 = 0.89 mho/m; & = 41.8; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS5 Configuration: Probe: ES3DV3 — SN3205; ConvF(6.04, 6.04, 6.04); Calibrated: 26.06.2009 Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 02.03.2010 Phantom: Flat Phantom 4.9L; Type: QDOOOP49AA; Serial: 1001 Measurement SW: DASY5, V5.2 Build 162; SEMCAD X Version 14.0 Build 57 Pin=250 mW /d=15mm, dist=3.0mm (ES—Probe)/Zoom Scan (7x7x7) /Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.3 V/m; Power Drift = 0.018 dB Peak SAR (extrapolated) = 3.55 W/kg SAR(I g) = 2.37 mW/g; SAR(10 g) = 1.55 mW/g Maximum value of SAR (measured) = 2.77 mW/g 0 dB = 2.77mW/g Certificate No: D835V2—4d021_Apr10 Page 6 of 9

Impedance Measurement Plot for Head TSL 21 fipr 2010 @9:10:02 (CHI) s1 1 U FS 4: 51.45%a —24531 8 77.699 pF 835.000 000 MHz Del Cor fAvg 16 CH2 Cor Av 16 * START 635.000 000 MHz STOP 1 109.000 000 MHz Certificate No: D835V2—4d021_Apr10 Page 7 of 9

DASY5 Validation Report for Body Date/Time: 29.04.2010 13:27:42 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN:4d021 Communication System: CW; Frequency: 835 MHz; Duty Cycle: 1: 1 Medium: MSL900 Medium parameters used: f = 835 MHz; 0 = 0.99 mho/m; &, = 54.9; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASYS5 Configuration: e Probe: ES3DV3 — SN3205; ConvF(5.97, 5.97, 5.97); Calibrated: 26.06.2009 e Sensor—Surface: 3mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 02.03.2010 e Phantom: Flat Phantom 4.9L; Type: QDOOOP49AA; Serial: 1001 e Measurement SW: DASY5, V5.2 Build 162; SEMCAD X Version 14.0 Build 57 Pin250 mW /d=15mm, dist=3.0mm (ES—Probe)/Zoom Scan (7x7x7) /Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 56.1 V/m; Power Drift = 0.030 dB Peak SAR (extrapolated) = 3.73 W/kg SAR(1 g) = 2.52 mW/g; SAR(10 g) = 1.65 mW/g Maximum value of SAR (measured) = 2.93 mW/g 12 18 0 dB = 2.93mW/g Certificate No: D835V2—4d021_Apr10 Page 8 of 9

Impedance Measurement Plot for Body TSL 29 fApr 2010 10:04:42 (CHI) sii 1 U Fs 1: 48.107 a —3.9023 6 48.844 pF 835.000 000 MHz CH1 Markers Del 2: 58.350 a 32.508 a Cor 900.000 MHz fvg 16 CH2 CH2 Markers Cor 21—10,592 d8 $00.000 MHz fv 16° START 635.000 000 MHz STOP 1 100.000 000 MHz Certificate No: D835V2—4d021_Apr10 Page 9 of 9


Document Created: 2011-03-31 10:20:41
Document Modified: 2011-03-31 10:20:41
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC