Module Approval Letter

FCC ID: YQD-M10

Cover Letter(s)

Download: PDF
FCCID_3623992

Company:Queclink Wireless Solutions Co.,Ltd Add:Room 501, Building 9, No 99, TianZhou Road, Shanghai, China Tel: +86 21 51082965-805 Fax: +86 21 54451990 Applicant Queclink Wireless Solutions Co.,Ltd FCC ID: YQD‐M10 Section 15.212 Modular Transmitters Request for Modular Approval  Request for Limited Modular Approval   Requirements EUT Conditions Comply(Y/N) Single Modular Approval Requirements 1 The radio elements of the modular The shielding of the radio Y transmitter must have their own shielding. portion can be The physical crystal and tuning capacitors demonstrated in EXHIBIT B may be located external to the shielded External Photo. radio elements. 2 The modular transmitter must have All inputs to the modules Y buffered modulation/data inputs (if such are buffered through logic inputs are provided) to ensure that the or microprocessor inputs. module will comply with part 15 Refer to Schematics. requirements under conditions of excessive data rates or over‐modulation. 3 The modular transmitter must have The modular rated power is Y its own power supply regulation. 4.0V. Refer to User manual. 4 The modular transmitter must comply The modular transmitter Y with the antenna and transmission system doesn’t have antenna requirements of §§15.203, 15.204(b) and connector which is 15.204(c). The antenna must either be accessible by user. Please permanently attached or employ a refer to: External “unique” antenna coupler (at all photograph exhibit. The connections between the module and the Maximum antenna gain antenna, including the cable). The allowed for user with this “professional installation” provision of device is 7.0dBi in GSM 850/ §15.203 is not applicable to modules but GPRS 850 and 3.00dBi in can apply to limited modular approvals GSM1900/ GPRS1900. under paragraph (b) of this section. 5 The modular transmitter must be The modular transmitter Y tested in a stand‐alone configuration, is connected to the i.e., the module must not be inside controlled board when another device during testing for testing. compliance with part 15 Please refer to setup requirements. Unless the transmitter photo. module will be battery powered, it must comply with the AC line conducted requirements found in

§15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). 6 If using a permanently affixed label, FCC ID is shown on the Y the modular transmitter must be label and permanently labeled with its own FCC affixed to this modular identification number, and, if the FCC transmitter, please Refer identification number is not visible to the label drawing. when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: YQD‐M10” or “Contains FCC ID: YQD‐M10”. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

7 The modular transmitter must The necessary Y comply with any specific rules or explanation to be operating requirements that complied with this ordinarily apply to a complete requirement is transmitter and the manufacturer contained in the user must provide adequate instructions manual, please along with the module to explain any refers to the User such requirements. A copy of these manual. instructions must be included in the application for equipment authorization. 8 The modular transmitter must The modular comply Y comply with any applicable RF with any applicable RF exposure requirements in its final exposure requirements configuration. in its final configuration. Sincerely Yours, Signature: Printed name: Wei Peng Title: manager


Document Created: 2017-10-31 14:15:52
Document Modified: 2017-10-31 14:15:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC