FCC Part 22H Report

FCC ID: YHLBLUJENNYSLD

Test Report

Download: PDF
FCCID_4079693

Uni+#+nTrust Page 1 of 29 Report No.: 181027005RFM—1 FCC TEST REPORT Product Name: Feature Phone Trade Mark: BLU Model No.: JENNY SLIDE Report Number: 181027005RFM—1 Test Standards: FCC 47 CFR Part 22 Subpart H FCC 47 CFR Part 2 FGG ID: YHLBLUJENNYSLD Test Result: PASS Date of Issue: November 19, 2018 Prepared for: BLU Products, Inc. 10814 NW 33rd St # 100 Doral, FL 33172 Prepared by: Shenzhen UnionTrust Quality and Technology Co., Ltd. 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China TEL: +86—755—2823 0888 FAX: +86—755—2823 0886 Tested by: Reviewed by: Kevin Liang Assistant Manager Approved by: November 19, 2018 Shenzhen UnionTrust Quality and Technology Co:; Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86—755—28230888 Fax: +86—755—28230886 E—mail: info@uttlab.com Hitp:/www.uttlab.com

Page 2 of 29 Report No.: 181027005RFM-1 Version Version No. Date Description V1.0 November 19, 2018 Original Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 3 of 29 Report No.: 181027005RFM-1 CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1 CLIENT INFORMATION ........................................................................................................................................ 4 1.2 EUT INFORMATION ............................................................................................................................................ 4 1.2.1 GENERAL DESCRIPTION OF EUT ............................................................................................................ 4 1.2.2 DESCRIPTION OF ACCESSORIES.............................................................................................................. 4 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD ................................................................................. 5 1.4 DESCRIPTION OF SUPPORT UNITS ...................................................................................................................... 5 1.5 TEST LOCATION ................................................................................................................................................. 5 1.6 TEST FACILITY ................................................................................................................................................... 5 1.7 DEVIATION FROM STANDARDS ............................................................................................................................ 6 1.8 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................. 6 1.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 6 1.10 MEASUREMENT UNCERTAINTY ........................................................................................................................... 6 2. TEST SUMMARY ...................................................................................................................................................... 7 3. EQUIPMENT LIST .................................................................................................................................................... 8 4. TEST CONFIGURATION .......................................................................................................................................... 9 4.1 ENVIRONMENTAL CONDITIONS FOR TESTING ........................................................................................................ 9 4.1.1 NORMAL OR EXTREME TEST CONDITIONS ............................................................................................... 9 4.2 TEST SETUP .................................................................................................................................................... 10 4.2.1 FOR RADIATED EMISSIONS TEST SETUP ................................................................................................ 10 4.2.2 FOR CONDUCTED RF TEST SETUP ........................................................................................................ 12 4.3 TEST CHANNELS ............................................................................................................................................. 13 4.4 SYSTEM TEST CONFIGURATION ........................................................................................................................ 13 4.5 PRE-SCAN ....................................................................................................................................................... 13 5. RADIO TECHNICAL REQUIREMENTS SPECIFICATION .................................................................................... 14 5.1 REFERENCE DOCUMENTS FOR TESTING ............................................................................................................ 14 5.2 EFFECTIVE RADIATED POWER (ERP) ............................................................................................................... 14 5.3 CONDUCTED OUTPUT POWER .......................................................................................................................... 16 5.4 PEAK-TO-AVERAGE RATIO ................................................................................................................................ 17 5.5 99%&26DB BANDWIDTH ................................................................................................................................. 19 5.6 BAND EDGE AT ANTENNA TERMINALS ............................................................................................................... 21 5.7 SPURIOUS EMISSIONS AT ANTENNA TERMINALS ................................................................................................. 23 5.8 FIELD STRENGTH OF SPURIOUS RADIATION ........................................................................................................ 25 5.9 FREQUENCY STABILITY .................................................................................................................................... 28 APPENDIX 1 PHOTOS OF TEST SETUP ..................................................................................................................... 29 APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS ................................................................................. 29 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 4 of 29 Report No.: 181027005RFM-1 1. GENERAL INFORMATION 1.1 CLIENT INFORMATION Applicant: BLU Products, Inc. Address of Applicant: 10814 NW 33rd St # 100 Doral, FL 33172 Manufacturer: BLU Products, Inc. Address of Manufacturer: 10814 NW 33rd St # 100 Doral, FL 33172 1.2 EUT INFORMATION 1.2.1 General Description of EUT Product Name: Feature Phone Model No.: JENNY SLIDE Add. Model No.: N/A Trade Mark: BLU DUT Stage: Identical Prototype GSM Bands: GSM850/1900 EUT Supports Function: 2.4 GHz ISM Band: Bluetooth V2.1+EDR IMEI Code: 869181029926126, 869181029926134 Sample Received Date: October 26, 2018 Sample Tested Date: October 26, 2018 to November 2, 2018 1.2.2 Description of Accessories Adapter Trade Mark: BLU Model No.: US-NB-0550 Input: 100-240 V~50/60 Hz 0.15 A Output: 5.0 V 550 mA AC Cable: N/A DC Cable: 1 Meter, Unshielded without ferrite Battery Trade Mark: BLU Model No.: N4C820T Battery Type: Lithium-ion Rechargeable Battery Rated Voltage: 3.7 Vdc Rated Capacity: 820 mAh Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 5 of 29 Report No.: 181027005RFM-1 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD Support Networks: GSM Type of Modulation: GSM GMSK Frequency Range: GSM 850: 824.2-848.8 MHz Max RF Output Power: GSM 850: 32.70dBm Type of Emission: GSM 850: 245KGXW Antenna Type: PIFA Antenna Antenna Gain: -0.4 dBi GPRS Class: Class 12 Normal Test Voltage: 3.7 Vdc Extreme Test Voltage: 3.5 to 4.2Vdc Extreme Test -30 °C to +50 °C Temperature: 1.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested with associated equipment below. 1) Support Equipment Description Manufacturer Model No. Serial Number Supplied by N/A N/A N/A N/A N/A 2) Support Cable Cable No. Description Connector Length Supplied by 1 Antenna Cable SMA 0.30 Meter UnionTrust 1.5 TEST LOCATION Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China 518109 Telephone: +86 (0) 755 2823 0888 Fax: +86 (0) 755 2823 0886 1.6 TEST FACILITY The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L9069 The measuring equipment utilized to perform the tests documented in this report has been calibrated once a year or in accordance with the manufacturer's recommendations, and is traceable under the ISO/IEC/EN 17025 to international or national standards. Equipment has been calibrated by accredited calibration laboratories. IC-Registration No.: 21600-1 The 3m Semi-anechoic chamber of Shenzhen UnionTrust Quality and Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 21600-1. A2LA-Lab Certificate No.: 4312.01 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 6 of 29 Report No.: 181027005RFM-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC Accredited Lab. Designation Number: CN1194 Test Firm Registration Number: 259480 1.7 DEVIATION FROM STANDARDS None. 1.8 ABNORMALITIES FROM STANDARD CONDITIONS None. 1.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER None. 1.10 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the Product as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. No. Item Measurement Uncertainty 1 Conducted emission 9KHz-150KHz ±3.8 dB 2 Conducted emission 150KHz-30MHz ±3.4 dB 3 Radiated emission 9KHz-30MHz ±4.9 dB 4 Radiated emission 30MHz-1GHz ±4.7 dB 5 Radiated emission 1GHz-18GHz ±5.1 dB 6 Radiated emission 18GHz-26GHz ±5.2 dB 7 Radiated emission 26GHz-40GHz ±5.2 dB Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 7 of 29 Report No.: 181027005RFM-1 2. TEST SUMMARY FCC 47 CFR Part 22 Subpart H Test Cases Test Item Test Requirement Test Method Result Effective Radiated FCC 47 CFR Part 2.1046(a) & ANSI/TIA-603-E-2016 & PASS Power (ERP) FCC 47 CFR Part 22.913(a) KDB 971168 D01v03r01 Conducted Output FCC 47 CFR Part 2.1046(a) & ANSI/TIA-603-E-2016 & PASS Power FCC 47 CFR Part 22.913(a) KDB 971168 D01v03r01 ANSI/TIA-603-E-2016 & Peak-to-average ratio FCC 47 CFR Part 22.913(a) PASS KDB 971168 D01v03r01 ANSI/TIA-603-E-2016 & 99%&26dB Bandwidth FCC 47 CFR Part 2.1049(h) PASS KDB 971168 D01v03r01 Band Edge at antenna FCC 47 CFR Part 2.1051 & ANSI/TIA-603-E-2016 & PASS terminals FCC 47 CFR Part 22.917(a) KDB 971168 D01v03r01 Spurious emissions at FCC 47 CFR Part 2.1051 & ANSI/TIA-603-E-2016 & PASS antenna terminals FCC 47 CFR Part 22.917(a)(b) KDB 971168 D01v03r01 Field strength of FCC 47 CFR Part 2.1053 & ANSI/TIA-603-E-2016 & PASS spurious radiation FCC 47 CFR Part 22.917(a)(b) KDB 971168 D01v03r01 FCC 47 CFR Part 2.1055 & ANSI/TIA-603-E-2016 & Frequency stability PASS FCC 47 CFR Part 22.355 KDB 971168 D01v03r01 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 8 of 29 Report No.: 181027005RFM-1 3. EQUIPMENT LIST Radiated Emission Test Equipment List Serial Cal. date Cal. Due date Used Equipment Manufacturer Model No. Number (mm dd, yyyy) (mm dd, yyyy) 3M Chamber & ETS-LINDGREN 3M N/A Dec. 20, 2015 Dec. 19, 2018 Accessory Equipment Receiver R&S ESIB26 100114 Dec. 10, 2017 Dec. 10, 2018 Broadband Antenna ETS-LINDGREN 3142E 00201566 Dec. 17, 2017 Dec. 17, 2018 Preamplifier HP 8447F 2805A02960 Dec. 10, 2017 Dec. 10, 2018 Broadband Antenna ETS-LINDGREN 3142E-PA 00201891 May 19, 2018 May 19, 2019 (Pre-amplifier) Horn Antenna ETS-LINDGREN 3117 00164202 Dec. 17, 2017 Dec. 17, 2018 Horn Antenna ETS-LINDGREN 3117-PA 00201874 May 22, 2018 May 22, 2019 (Pre-amplifier) Multi device ETS-LINDGREN 7006-001 00160105 N/A N/A Controller Wideband Radio Communication R&S CMW500 116254 June 07, 2018 June 07, 2019 Tester Test Software Audix e3 Software Version: 9.160323 2/3/4G RF Test System Equipment List Serial Cal. date Cal. Due date Used Equipment Manufacturer Model No. Number (mm dd, yyyy) (mm dd, yyyy) 1316.3003K07 Receiver R&S ESR7 Dec. 10, 2017 Dec. 10, 2018 -101181-K3 EXA Spectrum KEYSIGHT N9010A MY51440197 Dec.10, 2017 Dec. 10, 2018 Analyzer Wideband Radio Communication R&S CMW500 116254 June 07, 2018 June 07, 2019 Tester DC Source KIKUSUI PWR400L LK003024 Sep. 14, 2018 Sep. 13, 2019 Temp & Humidity 58566133290 Votisch VT4002 June 05, 2018 June 05, 2019 chamber 020 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 9 of 29 Report No.: 181027005RFM-1 4. TEST CONFIGURATION 4.1 ENVIRONMENTAL CONDITIONS FOR TESTING 4.1.1 Normal or Extreme Test Conditions Test Environment Selected Values During Tests Ambient Test Condition Temperature (°C) Voltage (V) Relative Humidity (%) TN/VN +15 to +35 3.7 20 to 75 TL/VL -30 3.5 20 to 75 TH/VL +50 3.5 20 to 75 TL/VH -30 4.2 20 to 75 TH/VH +50 4.2 20 to 75 Remark: 1) The EUT just work in such extreme temperature of -30 °C to +50 °C and the extreme voltage of 3.5 V to 4.2 V, so here the EUT is tested in the temperature of -30 °C to +50 °C and the voltage of 3.5 V to 4.2 V. 2) VN: Normal Voltage; TN: Normal Temperature; TL: Low Extreme Test Temperature; TH: High Extreme Test Temperature; VL: Low Extreme Test Voltage; VH: High Extreme Test Voltage. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 10 of 29 Report No.: 181027005RFM-1 4.2 TEST SETUP 4.2.1 For Radiated Emissions test setup Setup - 1_ERP Test setup Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 11 of 29 Report No.: 181027005RFM-1 Setup - 2_EIRP Test setup Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 12 of 29 Report No.: 181027005RFM-1 4.2.2 For Conducted RF test setup Normal Environment Extreme Environment Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 13 of 29 Report No.: 181027005RFM-1 4.3 TEST CHANNELS RF Channel Band Tx/Rx Frequency Low(L) Middle(M) High(H) Tx Channel 128 Channel 190 Channel 251 GSM (824 MHz ~ 849 MHz) 824.2 MHz 836.6 MHz 848.8 MHz 4.4 SYSTEM TEST CONFIGURATION For emissions testing, the equipment under test (EUT) setup to transmit continuously to simplify the measurement methodology. Care was taken to ensure proper power supply voltages during testing. During testing, radiated emission were performed with the EUT set to transmit at the channel with highest output power as worst-case scenario. It was powered by a 3.7Vdc rechargeable Li-on battery. Only the worst case data were recorded in this test report. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates, X/Y/Z axis, and antenna ports. All readings are extrapolated back to the equivalent three meter reading using inverse scaling with distance. Analyzer resolution is 100 kHz or greater for frequencies below 1000MHz. The resolution is 1 MHz or greater for frequencies above 1000MHz. The spurious emissions more than 20 dB below the permissible value are not reported. Radiated emission measurement were performed from the lowest radio frequency signal generated in the device which is greater than 9 kHz to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. 4.5 PRE-SCAN Pre-scan under all rate at lowest middle and highest channel, find the transmitter power as below: SIM 1 Card Conducted transmitter power measurement result. GSM 850 Maximum Average Power (dBm) Channel 128 190 251 Frequency(MHz) 824.2 MHz 836.6 MHz 848.8 MHz GSM (GMSK, 1Tx-slot) 32.69 32.70 32.67 GPRS (GMSK, 1Tx-slot) 32.63 32.65 32.66 GPRS (GMSK, 2Tx-slot) 31.02 31.15 31.21 GPRS (GMSK, 3Tx-slot) 29.43 29.62 29.70 GPRS (GMSK, 4Tx-slot) 27.95 28.13 28.34 Pre-scan all mode, find worse case mode are chosen to the report, the worse mode applicability and tested channel detail as below: Band Radiated Conducted 1) GSM (GMSK, 1Tx-slot) Link 1) GSM (GMSK,1Tx-slot) Link GSM/GPRS 2) GPRS (GMSK, 1Tx-slot) Link 2) GPRS (GMSK, 1Tx-slot) Link Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 14 of 29 Report No.: 181027005RFM-1 5. RADIO TECHNICAL REQUIREMENTS SPECIFICATION 5.1 REFERENCE DOCUMENTS FOR TESTING No. Identity Document Title Frequency allocations and radio treaty matters; general rules and 1 FCC 47 CFR Part 2 Subpart J regulations 2 FCC 47 CFR Part 22 Subpart H Cellular Radiotelephone Service Land Mobile FM or PM Communications Equipment Measurement 3 ANSI/TIA-603-E-2016 and Performance Standards 4 KDB 971168 D01 KDB 971168 D01 Power Meas License Digital Systems v03r01 5.2 EFFECTIVE RADIATED POWER (ERP) Test Requirement: FCC 47 CFR Part 2.1046(a) & FCC 47 CFR Part 22.913(a) Test Method: KDB 971168 D01v03& ANSI/TIA-603-E-2016 Limit: The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts. Test Procedure: Test procedure as below: 1) The EUT was powered ON and placed on a 0.8/1.5m high table at a 3 meter semi/fully Anechoic Chamber. The antenna of the transmitter was extended to its maximum length. Modulation mode and the measuring receiver shall be tuned to the frequency of the transmitter under test. 2) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3) The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360°the turntable. After the fundamental emission was maximized, a field strength measurement was made. 4) Steps 1) to 3) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 5) The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 6) A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 3) is obtained for this set of conditions. 7) The output power into the substitution antenna was then measured. 8) Steps 6) and 7) were repeated with both antennas polarized. 9) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB where: Pg is the generator output power into the substitution antenna. 10) Test the EUT in the lowest channel, the middle channel the Highest channel 11) The radiation measurements are performed in X, Y, Z axis positioning for EUT operation mode, and found the Y axis positioning which it is worse case. 12) Repeat above procedures until all frequencies measured was complete. Frequency Detector RBW VBW Remark Receiver Setup: 30MHz-1GHz Peak 100kHz 300kHz Peak Above 1GHz Peak 1MHz 3MHz Peak Test Setup: Refer to section 4.2.1 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Test Data: See table below Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 15 of 29 Report No.: 181027005RFM-1 Maximum ERP (dBm) Limit Channel GSM Result (dBm) Lowest 30.14 38.45 Pass Middle 30.15 38.45 Pass Highest 30.12 38.45 Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 16 of 29 Report No.: 181027005RFM-1 5.3 CONDUCTED OUTPUT POWER Test Requirement: FCC 47 CFR Part 2.1046(a) & FCC 47 CFR Part 22.913(a) Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 Limit: The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts. Test Procedure: The EUT was set up for the maximum power with GSM, GPRS, EDGE, WCDMA, CDMA2000, and LTE link data modulation and link up with simulator. Set the EUT to transmit under low, middle and high channel and record the power level shown on simulator. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.2.2 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Test Data: The full result refer to section 4.5 for details. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 17 of 29 Report No.: 181027005RFM-1 5.4 PEAK-TO-AVERAGE RATIO Test Requirement: FCC 47 CFR Part 22.913(a) Test Method: KDB 971168 D01v03r01 In measuring transmissions in this band using an average power technique, the peak- Limit: to-average ratio (PAR) of the transmission may not exceed 13 dB Test Procedure: The transmitter output was connected to a calibrated coaxial cable and coupler, the other end of which was connected to a spectrum analyzer. a) Set resolution/measurement bandwidth ≥ signal’s occupied bandwidth b) Set the number of counts to a value that stabilizes the measured CCDF curve c) Record the maximum PAPR level associated with a probability of 0.1 % Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.2.2 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Test Data: See table below GSM GPRS Limit Channel Result 1Tx-slot 1Tx-slot (dBm) Lowest 1.03 2.99 13 Pass Middle 3.02 1.66 13 Pass Highest 4.74 3.13 13 Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 18 of 29 Report No.: 181027005RFM-1 The test plot as follows: GSM 1Tx-slot GPRS 1Tx-slot Lowest Channel Middle Channel Highest Channel Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 19 of 29 Report No.: 181027005RFM-1 5.5 99%&26DB BANDWIDTH Test Requirement: FCC 47 CFR Part 2.1049(h) & FCC 47 CFR Part 22.917(b) Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 Limit: No Limit Test Procedure: The transmitter output was connected to a calibrated coaxial cable and coupler, the other end of which was connected to a spectrum analyzer. The occupied bandwidth was measured with the spectrum analyzer at the low, middle and high channel in each band. The 99% and -26dB bandwidths was also measured and recorded. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.2.2 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Test Data: See table below 99% & 26 dB Bandwidth Frequency 26 dB BW 99% BW Test Mode Channel (MHz) (kHz) (kHz) 128 824.2 317.2 243.28 GSM 1Tx-slot 190 836.6 315.1 241.72 251 848.8 317.5 244.59 128 824.2 312.8 241.70 GPRS 1Tx-slot 190 836.6 324.7 244.04 251 848.8 322.6 245.07 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 20 of 29 Report No.: 181027005RFM-1 The test plot as follows: GSM GPRS Lowest Channel Middle Channel Highest Channel Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 21 of 29 Report No.: 181027005RFM-1 5.6 BAND EDGE AT ANTENNA TERMINALS Test Requirement: FCC 47 CFR Part 2.1051 & FCC 47 CFR Part 22.917(a) Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 Limit: The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The emission limit equal to -13 dBm. Test Procedure: The transmitter output was connected to a calibrated coaxial cable and coupler, the other end of which was connected to a spectrum analyzer. For each band edge measurement: 1) Set the spectrum analyzer span to include the block edge frequency. 2) Set a marker to point the corresponding band edge frequency in each test case. 3) Set display line at -13 dBm 4) Set resolution bandwidth to at least 1% of emission bandwidth. 5) Set spectrum analyzer with RMS detector. 6) Record the max trace plot into the test report Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.2.2 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 22 of 29 Report No.: 181027005RFM-1 The test plot as follows: GSM 1Tx-slot GPRS 1Tx-slot Lowest Channel Highest Channel Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 23 of 29 Report No.: 181027005RFM-1 5.7 SPURIOUS EMISSIONS AT ANTENNA TERMINALS Test Requirement: FCC 47 CFR Part 2.1051 & FCC 47 CFR Part 22.917(a)(b) Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 Limit: The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The emission limit equal to -13 dBm. Test Procedure: The EUT makes a phone call to the communication simulator. All measurements were done at low, middle and high operational frequency range. b. Measuring frequency range is from 30 MHz to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. Set RBW & VBW to 100 kHz for the measurement below 1 GHz, and 1 MHz for the measurement above 1 GHz. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset. Test Setup: Refer to section 4.2.2 for details. Instruments Used: Refer to section 3 for details Test Mode: Link mode Test Results: Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 24 of 29 Report No.: 181027005RFM-1 The test plot as follows: GSM 1Tx-slot GPRS 1Tx-slot Lowest Channel Middle Channel Highest Channel Remark: 1) All the above conduction data, the fundamental frequency is not marked, it may exceed the limit, please ignore it. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 25 of 29 Report No.: 181027005RFM-1 5.8 FIELD STRENGTH OF SPURIOUS RADIATION Test Requirement: FCC 47 CFR Part 2.1053 & FCC 47 CFR Part 22.917(a)(b) Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 Receiver Setup: Frequency Detector RBW VBW Remark 0.009 MHz-30 MHz Peak 10 kHz 30 KHz Peak 30 MHz-1 GHz Quasi-peak 100 kHz 300 KHz Peak Above 1 GHz Peak 1 MHz 3 MHz Peak Limits: The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The emission limit equal to -13 dBm. Test Setup: Refer to section 4.2.1 for details. Test Procedures: 1. Scan up to 10th harmonic, find the maximum radiation frequency to measure. 2. The technique used to find the Spurious Emissions of the transmitter was the antenna substitution method. Substitution method was performed to determine the actual ERP/EIRP emission levels of the EUT. Test procedure as below: 1) The EUT was powered ON and placed on a 0.8/1.5m high table at a 3 meter semi/fully Anechoic Chamber. The antenna of the transmitter was extended to its maximum length. Modulation mode and the measuring receiver shall be tuned to the frequency of the transmitter under test. 2) The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3) The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360°the turntable. After the fundamental emission was maximized, a field strength measurement was made. 4) Steps 1) to 3) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 5) The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 6) A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 3) is obtained for this set of conditions. 7) The output power into the substitution antenna was then measured. 8) Steps 6) and 7) were repeated with both antennas polarized. 9) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB where: Pg is the generator output power into the substitution antenna. 10) Test the EUT in the lowest channel, the middle channel the Highest channel 11) The radiation measurements are performed in X, Y, Z axis positioning for EUT operation mode, and found the Y axis positioning which it is worse case. 12) Repeat above procedures until all frequencies measured was complete. Equipment Used: Refer to section 3 for details. Test Result: Pass The measurement data as follows: Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 26 of 29 Report No.: 181027005RFM-1 Radiated Emission Test Data GSM 1Tx-slot_Lowest Channel Horizontal Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1648.400 -47.95 3.59 -44.36 -13.00 -31.36 Peak 2 8242.000 -45.76 18.37 -27.39 -13.00 -14.39 Peak 3 9066.200 -45.80 18.74 -27.06 -13.00 -14.06 Peak Vertical Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1648.400 -35.10 3.59 -31.51 -13.00 -18.51 Peak 2 6593.600 -54.87 19.11 -35.76 -13.00 -22.76 Peak 3 7417.800 -52.29 18.30 -33.99 -13.00 -20.99 Peak GSM 1Tx-slot_Middle Channel Horizontal Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1673.200 -44.10 3.88 -40.22 -13.00 -27.22 Peak 2 4183.000 -55.43 13.67 -41.76 -13.00 -28.76 Peak 3 9202.600 -48.29 19.21 -29.08 -13.00 -16.08 Peak Vertical Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1673.200 -34.77 3.88 -30.89 -13.00 -17.89 Peak 2 7529.400 -55.27 18.31 -36.96 -13.00 -23.96 Peak 3 8366.000 -53.79 18.27 -35.52 -13.00 -22.52 Peak Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 27 of 29 Report No.: 181027005RFM-1 GSM 1Tx-slot_Highest Channel Horizontal Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1697.600 -49.97 4.17 -45.80 -13.00 -32.80 Peak 2 8488.000 -51.93 18.26 -33.67 -13.00 -20.67 Peak 3 9336.800 -47.02 19.52 -27.50 -13.00 -14.50 Peak Vertical Correction Frequency Reading Result No. factor Limit (dBm) Margin (dB) Remark (MHz) (dBm) (dBm) (dB) 1 1697.600 -34.93 4.17 -30.76 -13.00 -17.76 Peak 2 7639.200 -53.25 18.42 -34.83 -13.00 -21.83 Peak 3 8488.000 -50.69 18.26 -32.43 -13.00 -19.43 Peak Remark: 1) All tested is under the condition of the main wave is filtered out. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 28 of 29 Report No.: 181027005RFM-1 5.9 FREQUENCY STABILITY Test Requirement: FCC 47 CFR Part 2.1055 & FCC 47 CFR Part 22.355 Test Method: ANSI/TIA-603-E-2016 & KDB 971168 D01v03r01 The carrier frequency shall not depart from the reference frequency in excess of ±2.5 Limits: ppm for mobile stations. Test Setup: Refer to section 4.2.2 for details. Test Procedures: 1) Use CMW 500 or CMU 200 with Frequency Error measurement capability. a) Temp. = −30° to + 50°C b) Voltage =low voltage, 3.5 Vdc, Normal, 3.7 Vdc and High voltage, 4.2 Vdc. 2) Frequency Stability vs Temperature: The EUT is place inside a temperature chamber. The temperature is set to 20ºC and allowed to stabilize. After sufficient soak time, the transmitting frequency error is measured. The temperature is increased by 10 degrees, allowed to stabilize and soak, and then the measurement is repeated. This is repeated until +50ºC is reached. 3) Frequency Stability vs Voltage: The peak frequency error is recorded (worst-case). Equipment Used: Refer to section 3 for details. Test Result: Pass Channel/ Voltage Temperature Deviation Deviation Limit Modulation Frequency Pass/ Fail (MHz) (Vdc) (℃) (Hz) (ppm) (ppm) GSM 1Tx-slot VL 9 0.0108 ± 2.5 Pass VN TN 11 0.0131 ± 2.5 Pass VH 7 0.0084 ± 2.5 Pass 50 13 0.0155 ± 2.5 Pass 40 12 0.0143 ± 2.5 Pass 30 16 0.0191 ± 2.5 Pass GMSK 190 / 836.6 20 12 0.0143 ± 2.5 Pass VN 10 13 0.0155 ± 2.5 Pass 0 8 0.0096 ± 2.5 Pass -10 11 0.0131 ± 2.5 Pass -20 17 0.0203 ± 2.5 Pass -30 13 0.0155 ± 2.5 Pass Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com

Page 29 of 29 Report No.: 181027005RFM-1 APPENDIX 1 PHOTOS OF TEST SETUP See test photos attached in Appendix 1 for the actual connections between Product and support equipment. APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS Refer to Appendix 2 for EUT external and internal photos. *** End of Report *** The test report is effective only with both signature and specialized stamp. The result(s) shown in this report refer only to the sample(s) tested. Without written approval of UnionTrust, this report can’t be reproduced except in full. Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Qingxiang Road No.1, Longhua New District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: info@uttlab.com Http://www.uttlab.com


Document Created: 2019-04-21 16:29:37
Document Modified: 2019-04-21 16:29:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC