19030048SAR-1_FCC_SAR_Appendix_C2

FCC ID: YHLBLUG8

RF Exposure Info

Download: PDF
FCCID_4280130

In Collabaration with I”il e _a CALIDRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hittp:/wwwwchinattl.en Impedance Measurement Plot for Body TSL Tri s11 tog Hag 10.00d8/ reF 0.000d8 [F1} 50. 00 z 34— 83500000 itz — 46. 00 20.00 20. 00 10.00 0.000 —10.00 7 Bs +. sz —20.00 § id ~10.00 50. 00 —— _—__— x MSH s11 saith (tJx) seate 1,0000 (F1 oel} o »1 §35,.00000 tz 46.638 0 ~6,.7757 n 28.1/0 pFCo / A~ 1 Start 655 M BW 100 Ne Step oss ctte Pnd 1 Certificate No: Z18—60116 Page 8 of 8

In Collaboration with wl &¥ mt 4# a(/"}/, ‘ SNJ/z _ PERAH s i pe a s q — $* \\-"/ d n 2 4 * RBI caurration tatormon {Je=E® gocl {E@Ag 6 Wik Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China €/¢:\\\? & CALIBRATION Tel: +86—10—62304633—2079 E—mail: ett{@chinattl.com Fax:+86—10—62304633—2504 http://wwwchinattl.en Wls‘ w S CNAS 1.0570 Client Hydsoft Testing Co., Ltd Certificate No: 218—60119 CALIBRATION CERTIFICATE Object D1800V2 — SN: 24140 Calibration Procedure(s) FF—211—003—01 Calibration Procedures for dipole validation kits Calibration date: May 18, 2018 This calibration Cerfificate documents the traceabhility to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)‘c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 102083 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRP—Z91 100542 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAE4 SN 1525 02—Oct—17(SPEAG,No.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 . NetworkAnalyzer E5071C MY46110873 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer e {( Z_/ Reviewed by: Lin Hao SAR Test Engineer . Tfidi'%? B Approved by: Qi Dianyuan .. SAR Project Leader ie C 3 Issued: May 20, 2018 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: Z18—60119 Page 1 of 8

t In Collaboration with ‘/"}"/, s _p_ e a 00 CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: 186—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp://www.chinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices usedin close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to positionits feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60119 Page 2 of 8

In Collaboration with 4‘ s p_ e a q CALIBRATION LABRORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett@chinattl.com https//wwa.chinattl.en Measurement Conditions DASY system configuration, as far as not givenon page 1. DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 1800 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 41.0% 6 % 1.36 mho/m + 6 % Head TSL temperature change during test <1.0 °C SAR result with Head TSL SAR averagedover 1_cnm" _(1 g) of Head TSL Condition SAR measured 250 mW input power 9.57 mW /g SAR for nominal Head TSL parameters normalized to 1W 39.2 mW 7qg £ 18.8 % (k=2) SAR averaged over 10 cCn(10 g) of Head TSL Condition SAR measured 250 mW input power 4.92 mW 1 g SAR for nominal Head TSL parameters normalized to 1W 20.0 mW 1g 4 18.7 % (ke2) Body TSL parameters The following parameters and calculations were applied. Temporature Pormnittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 54.8% 6 % 1.48 mho/m # 6 % Body TSL temperature change during test <1.0 °C SAR result with Body TSL SAR averaged over 1 _cm" _(1 g) of Body TSL Condition SAR measured 250 mW input power 9.53 mW /g SAR for nominal Body TSL parameters normalized to 1W 39.0 mW 1g + 18.8 % (k=2) SAR averaged over 10 cm" (10 g) of Body TSL Condition SAR measured 250 mW input power 4.96 mW /g SAR for nominal Body TSL parameters normalized to 1W 201 mW 1g 4 18.7 % (ke2) Certificate No: Z18—60119 Page 3 of 8

In Callabartation with s_ p e a 0 CALIBRATION LABORATORY Add: No,51 Xucyuan Road, Haidian District, Beijing, 100191, China ‘Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp//wwwchinattl.en Appendix (Additional assessments outside the scope of CNAS L.0570) Antenna Parameters with Head TSL Impedance, transformed to feed point 48.70— 3.10]0 Return Loss —29.30B Antenna Parameters with Body TSL Impedance, transformed to feed point 43.80— 3.22jQ Return Loss —22.6d4B General Antenna Parameters and Design Electrical Delay (one direction) 1.059 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60119 Page 4 of 8

& In Collsbaration with "",‘v’«' B , :‘f.; fi—b @ q'EJ 6 CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett@chinattl.com hitp://www.chinattl.en DASYS Validation Report for Head TSL Date: 05.17.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1800 MHz; Type: D1800V2; Serial; D1800V2 — SN: 20140 Communication System: UID 0, CW; Frequency: 1800 MHz; Duty Cycle: 1: 1 Medium parameters used: f= 1800 MHz; o = 1.359 8/m; sr = 40.97; p = 1000 kg/m3 Phantomsection: Flat Section Measurement Standard: DASYS (IEBE/IEC/ANSI C63.19—2007) DASYS Configuration: e Probe: EX3DV4 — SN7464; ConyF(8.42, 8.42, 8.42); Calibrated: 9/12/2017; e Sensor—Surface; 1,4mm (Mechanical Surface Detection) e Electronics: DABA4 Sn{525; Calibrated: 10/2/2017 & Phantom: Triple Flat Phantom5.1C; Type: QD 000 P51 CA; Serial; 1 161/1 e Measurement SW; DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=S$mm, dy=5mm, dz=5mm Reference Value = 99.70 V/m; Power Drift =—0.07 dB Peak SAR (extrapolated) = 18.9 W/kg SAR(I g)=9.57 W/kg; SAR(10 g) = 4.92 W/kg Maximumvalue of SAR (measured) = 15.5 W/kg —7.56 |—r1.35 1—15.13 & ~18.91 0 dB =15,5 W/kg =11.90 dBW/g Certificate No: Z18—60119 Page 5 of 8

. In Collaboration with i /Iu v'i/:" ,/y :” fi‘) ” fiL‘j’ ,,fl, i § CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hittp://wwww.chinattl.en Impedance Measurement Plot for Head TSL Tri s11 Log Hag 10.000a/ ref 0.000d8 [Fi} 5990 153 ~1,0000000 onz —20. 313 do 40.00 30. 00 20. 00 10,00 0. 000 —10.00 r—yee —20,00 —. § ~20,00 —40.00 50. 00 PIGE] si1 smith (R+Jx) scale 1,000u [FL vel) >1 1,8000000 cHz 48.659 n ~3,1005 0 28. $18—pF _ T*~% IBatnéeet = ~_—— iimmnnons — _ irAW 100He —Step 2 o NB( Certificate No: Z18—60119 Page 6 of 8

In Collabaration with 1j , s_p_ e a q CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett{@chinattl.com http:/www.chinattl.on DASY5 Validation Report for Body TSL Date: 05.16.2018 Test Laboratory: CTTL, Beijing, China DUT; Dipole 1800 MHz; Type: D1800V2; Serial: D1800V2 — SN: 20140 Communication System: UID 0, CW; Frequency: 1800 MHz; Duty Cycle: 1:1 Medium parameters used: f= 1800 MHz; 0 = 1.481 $/m; sr = 54.84; p = 1000 kg/m3 Phantom section: Center Section Measurement Standard: DASY5 (IBEE/IEC/ANSI C63.19—2007) DASYS5 Configuration: e Probe: EX3DV4 — SN7464; ConyF(8.45, 8.45, 8.45); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) « Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 & Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 116171 e Mcasurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=Smm, dz=5mm Reference Value = 86.02 V/m; Power Drift =—0.08 dB Peak SAR (extrapolated) = 17.8 W/kg SAR(I g)=9.53 W/kg; SAR(10 g) = 4.96 W/kg Maximum value of SAR (measured) = 14.8 W/kg ) —10.40 [—13.07 ~17.34 0 dB =14.8 W/kg =11,70 dBW/kg Certificate No: Z18—60119 Page 7 of 8

In Collsboration with s p e a 0 CALIBRATION LAGORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett{@chinattl.com http:/lwww.chinatth.on Impedance Measurement Plot for Body TSL "Tri si1 Log Hag 10.00d5/ ReF0,000db [F1] 5990 rsa~1,8000000 ailz —22. 617 da 40. 00 30. 00 20. 00 10.00 0. 000 p) 10. 00 rrrrreaaagl *h o L222z —20,00 \Y\ ol 30. 00 —40, 00 —50. 00 > a p[BZ] si1 saith (ReJX) scale 1.000U [Fi oel) >L 1.8000000 Gilz 43.843 n —3.2175 0 27.480—pFr=ians Rieeaert 1Stat 166t _ _ mssc ——oiwinh _ ——inCc * tupe orron Certificate No: Z18—60119 Page 8 of 8

r In Collaboration with \\{\\‘w”/,’ A 'l'mikfil T"V‘/, s_p e 0 ___ $y [E aon in CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China — se CNAS t F2 < //—'\\‘\§ a. v CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 "lalyho CNAS 10570 E—mail: ettt@chinattl.com hittps/www.chinatthon Client Hydsoft Testing Co., Ltd Certificate No: 218—60120 CALIBRATION CERTIFICATE Object D1900V2 — SN: 509 Calibration Procedure(s) FP—211—003—01 Calibration Procedures for dipole validationkits Calibration date: May 18, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements andthe uncertainties with confidence probability are given onthe following pages andare part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22#3)‘c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID i# Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRV—Z5 100542 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAEA4 SN 1525 02—Oct—17(SPEAG,No.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibratedby, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 NetworkAnalyzer ES071C MY46110673 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Name Function Signature Cali alibrated by $ i Zhao Jing f SAR Test Engineer —}g [_/ Reviewed by: Lin Hao SAR Test Engineer Tk(itjéi Approvedby: Qi Dianyuan SAR Project Leader .‘—M.fl,w/ Issued: May 20, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z18—60120 Page 1 of 8

r In Collabaration with s‘/"/‘/, Cl« s p_ e a q _ CALIERATION LAGORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—6230—4633—2504 E—mail: ett!@chinattl.com https//wwwehinattl.en lossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximily to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available fromthe Validation Reportat the end of the certificate. All figures statedin the certificate are validat the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacerto positionits feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned underthe liquidfilled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input powerof 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are usedto calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60120 Page 2 of 8

In Callabaration with TT 80 . . CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitpo//www.chinattLen Measurement Conditions DASY systemconfiguration, as far as not givenon page 1. DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Centor— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 1900 MHz a 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Pormittivity Conductivity Nominal Head TSL paramoters 22.0 °C 40.0 140 mho/m MeasuredHead TSL. parameters (22.0 2 0.2) °C 40.7 £ 6 % 1.40 mho/m + 6 % Head TSL temperature change during test <1.0 °C ——— SAR result with Head TSL SAR avoragedover 1 cm" (1g) of Hoad TSL Condition ofi e ce —____‘ SAR measured 250 mW input power 9.85 mW /g SAR for nominal Head TSL parameters normalized to 1W 30.6 mW 7g & 18.8 % (lc2) SAR avoragedover 10 cm> (10 g) of Head TSL Condition SAR measured 250 mW input power 5.04 mW /g SAR for nominal Head TSL. parameters normalized to 1W 20.2 mW 7g 18.7 % (Ic=2) Body TSL parameters The following parameters andcalculations were applied. Temporature Pormittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m MeasuredBody TSL parameters (22.0 £ 0.2) °C 54.6 + 6 % 1.49 mho/m£ 6 % Body TSL temperature change during test <1.0 °C SAR result with Body TSL SAR averagedover 1_cn" _(1 g) of Body TSL Condition SAR measured 250 mW input power 9.73 mW /g SAR for nominal Body TSL parameters normalized to 1W 39.5 mW /g £ 18.8 % (k=2) SAR averagedover 10 cmJ (10 g) of Body TSL Condition SAR measured 250 mW input power 5.04 mW / g SAR for nominal Body TSL parameters normalizedto 1W 20.4 mW 1g # 18.7 % (k2) Certificate No: Z18—60120 Page 3 of 8

,& " In Callaboratic with ——aa aD t ®‘/"/ /,s_ p e a 0_ l0« CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62301633—2079 Fax: +86—10—62304633—2504 E—mail: ettt@chinattl.com hitps//hwww.ehinattl.en Appondix (Additional assessments outside the scope of CNAS 1.0570) Antenna Parameters with Head TSL Impedance, transformedto feed point 45.50— 6.56J0 Return Loss —21.60B Antenna Paramoters with Body TSL Impedance, transformedto feed point 44.30— 3.95J0 Return Loss —22.70B General Antenna Parameters and Design CJ Electrical Delay (one direction) 1.065 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connectedto the secondarm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching whenloaded according to the position as explainedin the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole lengthis still according to the Standard. No excessive force must be appliedto the dipole arms, because they might bendor the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60120 Page 4 of 8

In Callabarationwith ‘T"T/.s p e a g _ ‘r CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—623041633—2079 Fax: +86—10—62304633—2504 E—mail: ett@chinattl.com http://www.chinatt.en DASY5 Validation Report for Head TSL Date: 05.18.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 « SN;: 509 Communication System: UID 0, CW; Frequeney: 1900 MHz; Duty Cyele: 1: 1 Medium parameters used: [= 1900 MHz; 0 = 1.4 8/m; er = 40.69; p = 1000 kg/m3 Phantom section: Right Section Mecasurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7464; ConvF(8.39, 8.39, 8.39); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAEA4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 116171 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Sean (7x‘7x7) (7x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, dz=5mm Reference Value = 100.3 V/m; Power Drift =—0.06 dB Peak SAR(extrapolated) = 19.7 W/kg SAR(I g) =9.85 W/kg; SAR(1O g) = 5.04 W/kg Maximum value of SAR (measured) = 15.9 W/kg 12.76 17.01 ig= —21.26 0 dB = 15.9 W/kg =12.01 dBW/kg Certificate No: Z18—60120 Page 5 of 8

% In Callabaration with T"F/ s a 4 17 t CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett@chinattl.com hitp//www.chinattl.en Impedance Measurement Plot for Head TSL. ir1 s11 Log fag 10,.00d8/ ref 0.000d8 (F1) so. 00 >1 1.9000000 aliz —21.617 da 40.00 30,00 20.00 10,00 0.000 ; 1000 | hniniak..L. punets ~20,00 *R e 4 ~20.00 * ~40.00 ~50.00 — y DpS®) s11 suich (Rijx) seale 1.000u [F1 oel) »11,9000000 oiz 45. 514 0 —6.5605 0 12. 76®—pF o ~—_ ue 1 Stert 1.7 GHe IFOW100 He Step2.1 o [ROllt Certificate No: Z18—60120 Page 6 of 8

In Collabaration with T"V‘/ s p e a 9 CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China ‘Tel: +86—10—62304633—2079 Fax: +86—10—623041633—2504 E—mail: ettt@chinattl.com http://wwas.chinattLen DASYS Validation Report for Body TSL Date: 05.16.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type; D1900V2; Serial; D1900V2 — SN: 509 Communication System: UID 0, CW; Frequency: 1900 MHz; Duty Cyele: 1:1 Medium parameters used: [= 1900 MHz; 0 = 1493 $/m; &, = 54.55; p = 1000 kg/m" Phantomsection: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI C€63.19—2007) DASYS Configuration: e Probe: EX3DV4 — SN7464; ConyF(8.32, 8.32, 8.32); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x‘7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 83.13 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 18.3 W/kg SAR(I g)=9.73 W/kg; SAR(1O g) = 5.04 W/kg Maximum value of SAR (measured) = 15.3 W/kg dB 0 —3.61 4.01 +10.02 4442 .. ~18.03 0 dB = 15.3 W/kg =11.85 dBW/kg Certificate No: Z18—60120 Page 7 of 8

In Collabaration with o un gpt T"T/s a CALIRRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com https//wwwehinattLen Impedance Measurement Plot for Body TSL [ ir1 sit Log May 10.00d8/ ref 000008 [F1} 590 (51~1,5000000 onz ~27.700 do — 40.00 | 30.00 | 2000 | | 10.00 0.000 —10, 00 * Siasues.. ssm ~—__ a ~20.00 *s= i¥ ..uen —50.00 —40, 60 ~$0,00 —— — ~——% (MHH s1t smith (@1Jx) scale 1.000u (r1 vel) »1 19000000 altz 44320 0 3.9408 0 11.749[(-;7?'”-7 * * i * / ~ C 1 Swi17Gt Irew100 e stcp21 ct Ki Certificate No: Z18—60120 Page 8 of 8

sez m3 in Collaboration with ‘\\\\\E'/’Iu/,l BA i®‘/";‘}, s_p_ e 3 9 $y3 A AEEi g E. 4 O 4 EAuBRAToN Lanoratory: M CN /_\ x AS datk \“\ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China > v CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 fil.\\\‘\ CNAS LO570 E—mail: ettl@chinattl.com Hitp://www.chinattl.en Client TA(Beijing) Certificate No: Z16—97114 CALIBRATION CERTIFICATE Object D2450V2 — SN: 883 Calibration Procedure(s) FD—z11—2—003—01 Calibration Procedures for dipole validation kits Calibration date: July 5, 2016 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility; environment temperature(22#3)‘c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Reference Probe EX3DV4 SN 7307 19—Feb—16(SPEAG,No.EX3—7307_Feb16) Feb—17 DAE4 SN 771 02—Feb—16(CTTL—SPEAG,N0.Z16—97011) Feb—17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 01—Feb—16 (CTTL, No.J16X00893) Jan—17 Network Analyzer E5071C MY46110673 26—Jan—16 (CTTL, No.J16X00894) Jan—17 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer z%J Reviewed by: Qi Dianyuan SAR Project Leader Approved by: Lu Bingsong Deputy Director of the laboratory %;Z’ Issued: July 7, 2 16 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z16—97114 Page 1 of 8

We $ In Collaboration with 428 e #=‘/"}‘/, s _DB__2_ 3 _8 k ‘(J\”un/\'l ION LABRORATORY Wiigeges~ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com Hitp://www.chinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z16—97114 Page 2 of 8

In Collebaration with s& p5 ea 2 © CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.on Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.8.8.1258 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 39.0 +6 % 1.77 mho/m 6 % Head TSL temperature change during test <1.0 °C SAR result with Head TSL SAR averaged over 1_cm> _(1 g) of Head TSL Condition SAR measured 250 mW input power 13.0 mW/g SAR for nominal Head TSL parameters normalized to 1W 52.4 mW /g & 20.8 % (k=2) SAR averaged over 10 em (10 g) of Head TSL Condition SAR measured 250 mW input power 6.06 mW /g SAR for nominal Head TSL parameters normalized to 1W 24.3 mW 1g £ 20.4 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 52.9 +6 % 1.97 mho/m +6 % Body TSL temperature change during test <1.0 °C ——— SAR result with Body TSL SAR averaged over 1 cm" (1 g) of Body TSL Condition SAR measured 250 mW input power 13.0 mW/g SAR for nominal Body TSL parameters normalized to 1W 51.8 mW ig + 20.8 % (k=2) SAR averaged over 10 em (10 g) of Body TSL Condition SAR measured 250 mW input power 6.18 mW /g SAR for nominal Body TSL parameters normalized to 1W 24.7 mW Ig * 20.4 % (k=2) Certificate No: Z16—97114 Page 3 of 8

In Collaboration with ®C + __ _2 3 € « CALIBRATION LABRORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com Http:/www.chinattl.en Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 54.60+2.77j0 Return Loss —25.80B Antenna Parameters with Body TSL Impedance, transformed to feed point 50.70+ 4.28J0 Return Loss —27.30B General Antenna Parameters and Design Electrical Delay (one direction) 1.263 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z16—97114 Page 4 of 8

In Collaboration with 1‘J, CALIBRATION s_p e_LABORATORY a q Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.en DASY5 Validation Report for Head TSL Date: 07.05.2016 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 883 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: £= 2450 MHz; 0 = 1.767 S/m; sr = 39.01; p = 1000 kg/m3 Phantomsection: Right Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7307; ConvF(7.36, 7.36, 7.36); Calibrated: 2/19/2016; e Sensor—Surface: 2mm (Mechanical Surface Detection) e Electronics: DAE4 Sn771; Calibrated: 2/2/2016 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 106.5 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 26.7 W/kg SAR(I g) = 13 W/kg; SAR(10 g) =6.06 W/kg Maximum value of SAR (measured) = 19.7 W/kg dB 0 ~4.45 —8.90 13.36 —17.81 £.: —22.26 1 0 dB = 19.7 W/kg = 12.94 dBW/kg Certificate No: Z16—97114 Page 5 of 8

!“‘* In Collaboration with !” [ s o_ e 3u9 _ ——atd l/ » CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinattl.com Hitp://www.chinattl.en Impedance Measurement Plot for Head TSL Tri s11 Log Mag 10.00d8/ Ref 0.000ds [F1] 10. 68 >1 2.4500000 cHz —25.815 do 40. 00 30. 00 20.00 10.00 0. 000 p) —10.00 =20.00 i —30.00 —40.00 |I>iMiE] ~50.00 si1 smith (@+jx) scale 1.000U [F1 bel] < »1 2.4500000 Ghz 54.583 o 2.7724 o 180.10—pf° 1 Stat 225 6tz TFBW 100 He Stop 2.65 oHte Teeil(1 Certificate No: Z16—97114 Page 6 of 8

_* * In Collaboration with @‘ /"}‘}, CALIBRATION Y2 l‘l‘ a 0 s_p_ eLABORATORY clgrzgy.o Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinattl.com Hitp://www.chinattl.en DASYS5 Validation Report for Body TSL Date: 07.05.2016 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 883 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: £= 2450 MHz; o = 1.972 $/m; & = 52.92; p = 1000 kg/m‘ Phantom section: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASYS5 Configuration: e Probe: EX3DV4 — SN7307; ConvF(7.22, 7.22, 7.22); Calibrated: 2/19/2016; e Sensor—Surface: 2mm (Mechanical Surface Detection) e Electronics: DAE4 Sn771; Calibrated: 2/2/2016 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.89 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 25.6 W/kg SAR(I g) = 13 W/kg; SAR(10 g) = 6.18 W/kg Maximumvalue of SAR (measured) = 19.3 W/kg dB 0 ~4.22 ~8.44 ~12.65 —16.87 L»" 3 —21.09 i * 0 dB = 19.3 W/kg = 12.86 dBW/kg Certificate No: Z16—97114 Page 7 of 8

!‘- h In Collaboration with @@‘}"/‘}, 5_ _p__ & 3 _O _, ¥ j 4 e ——an Ru V/ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett!@chinattl.com Hitp://www.chinattl.en Impedance Measurement Plot for Body TSL Tri si1 Log Mag 10.00d8/ Ref 0.000d8 [F1i] I 15900 t5a—2.2300000 onz —27.332 ds | 40.00 20.00 | 20.00 |_ 10.00 | 0.000p) n J —10.00 h | —20.00 i | —30.00 | —40.00 | ~50.00 x |>um® si1 smith (R+jx) scale 1.000U [F1 Del] »>1. 2,4500000 cz 50.671 n 4.2707 n 278.9 \ (1. Start 2.25 GHz IFBW 100 He Stop 2.55 6t [eSslil Certificate No: Z16—97114 Page 8 of 8

Justification for Extended SAR Dipole Calibrations Date of Return Loss Dipole Delta (%) Impedance Delta(ohm) Measurement (dB) July. 05, 2016 -25.8 - 54.6 - Head 2450 MHz July. 01, 2018 -23.8 7.8 53.8 -0.8 Note: The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification results meet the requirement of extended calibration.

Justification for Extended SAR Dipole Calibrations Date of Return Loss Dipole Delta (%) Impedance Delta(ohm) Measurement (dB) July. 05, 2016 -27.3 - 50.7 - Body 2450 MHz July. 01, 2018 -27.2 0.4 51.9 1.2 Note: The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification results meet the requirement of extended calibration.


Document Created: 2019-05-11 14:29:00
Document Modified: 2019-05-11 14:29:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC