Test report 15B - report

FCC ID: YBN-PIVISBX0

Test Report

Download: PDF
FCCID_4182313

TEST REPORT No.: 18-1-0200901T08a-C1 According to: FCC Regulations Part 15.109, Class B ISED-Regulations RSS-Gen, Issue 5 ICES-003, Issue 6 for Robert Bosch Car Multimedia GmbH PIVISBX0 Multimedia Device with WLAN and Bluetooth FCC-ID: YBN-PIVISBX0 ISED: 9595A- PIVISBX0 Laboratory Accreditation and Listings Voluntary Controls for Electromagnetic Industry Canada Emissions Reg. No.: 3462D-1 Reg. No.: 3462D-2 Reg. No.: Reg. No.: 3462D-3 R-4552, C-20009, Accredited EMC-Test Laboratory T-20006, G-20013 MRA US-EU 0003 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Laboratory Accreditation and Listings Page 1 of 18 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 18-1-0200901T08a-C1, Page 2 of 18 Table of contents 1. SUMMARY OF TEST RESULTS................................................................................................................... 3 1.1. RX mode, tests overview according FCC Part 15B and Canadian ISED (RSS) Standards .......................... 3 1.2. Attestation:.................................................................................................................................................... 3 2. ADMINISTRATIVE DATA ............................................................................................................................ 4 2.1. Identification of the testing laboratory .......................................................................................................... 4 2.2. Test location ................................................................................................................................................. 4 2.3. Organizational items ..................................................................................................................................... 4 2.4. Applicant’s details ........................................................................................................................................ 5 2.5. Manufacturer’s details .................................................................................................................................. 5 2.6. Factory details ............................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) .............................................................................................................. 6 3.1. EUT: Type, S/N etc. and short descriptions used in this test report ............................................................. 6 3.2. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions ............................................................... 6 3.3. EUT set-ups .................................................................................................................................................. 6 3.4. EUT operating modes ................................................................................................................................... 7 4. DESCRIPTION OF TEST SYSTEM SET-UP’S ........................................................................................... 8 4.1. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz ............................................ 8 4.2. Test system set-up for radiated electric field measurement above 1 GHz .................................................... 9 5. MEASUREMENTS ........................................................................................................................................ 10 5.1. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz ......................................................... 10 5.2. General Limit - Radiated emissions, above 1 GHz ..................................................................................... 11 5.3. Measurement uncertainties ......................................................................................................................... 12 6. ABBREVIATIONS USED IN THIS REPORT ............................................................................................ 13 7. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES .................... 13 8. INSTRUMENTS AND ANCILLARY ........................................................................................................... 14 9. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ........................................................................ 18 END OF TEST REPORT ................................................................................................................................... 18 Table of annex Total pages SEPARATE ANNEX 1: DIAGRAM OF TESTING “CETECOM_TR18-1-0200901T08a-A1” 6 SEPARATE ANNEX 2: INTERNAL PHOTOGRAPHS OF EUT “Supplied by Customer” SEPARATE ANNEX 3: EXTERNAL PHOTOGRAPHS OF EUT “CETECOM_TR18-1-0200901T08a-A3” 10 SEPARATE ANNEX 4: TEST SETUP PHOTOGRAPHS “CETECOM_TR18-1-0200901T08a-A4” 4 The listed attachments are an integral part of this report. CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 3 of 18 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. Also we refer on special conditions which the applicant should fulfill according §2.927 to §2.948, special focus regarding modification of the equipment and availability of sample equipment for market surveillance tests. The Equipment Under Test (in this report, hereinafter referred as EUT) is a Car Radio System with Navigation, WLAN and Bluetooth technology. A typical operation mode was set-up as described in chapter 3.4 according applicants instructions. Following tests have been performed to show compliance with applicable FCC Part 15, Subpart B (Unintentional Radiators) of the CFR 47 Rules, Edition 2015 and Canadian RSS standards. 1.1. RX mode, tests overview according FCC Part 15B and Canadian ISED (RSS) Standards No. of References & Limits EUT EUT Diagram Test case Port op- Result set-up group FCC Standard RSS Section Test limit mode RSS-132, FCC 15.109 Receiver Issue 3: 6.6 class B limits Cabinet + §15.109 RSS-Gen, 3&4 Interconnec §15.33 1 1 Passed radiated Issue 5: 5.3 RSS-Gen: ting cables §15.35 emissions RSS 133, Chapter 5.3+Chapter Issue 6: 6.6 7.1.2 Remark: 1.2. Attestation: I declare that all measurements were performed by me or under my supervision and that all measurements have been performed and are correct to my best knowledge and belief to Industry Canada standards. All requirements as shown in above table are met in accordance with enumerated standards. The current version of the Test Report CETECOM_TR18-1-0200901T08a-C1 replaces the Test Report CETECOM_ TR18-1-0200901T08a dated 2018-12-28. The replaced test report is herewith invalid. Digital unterschrieben von B.Sc. Mohamed Ahmed DN: cn=B.Sc. Mohamed Ahmed, o=Cetecom GmbH, ou=RC/EMC, email=mohamed.ahmed@ceteco m.com, c=DE Datum: 2019.01.24 16:36:56 +01'00' ...................................................... .................................................... Dipl.-Ing. Niels Jeß B.Sc. Mohamed Ahmed Responsible for test section Responsible for test report CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 4 of 18 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report: B.Sc. M. Ahmed project leader: Dipl.-Ing N. Perez Receipt of EUT: 2018-12-30 Date(s) of test: 2018-12-17 – 2018-12-21 Date of report: 2019-01-24 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 5 of 18 2.4. Applicant’s details Applicant’s name: Robert Bosch Car Multimedia GmbH Address: Robert-Bosch-Straße 200 31139 Hildesheim Germany Contact person: Mr. Salvatore Miraglia 2.5. Manufacturer’s details Applicant’s name: Robert Bosch Car Multimedia GmbH Address: Robert-Bosch-Straße 200 31139 Hildesheim Germany 2.6. Factory details Factory 1: Robert Bosch Car Multimedia Portugal, S.A. Address: Rua Max Grundig, 35-Lomar 4705-820 Braga Portugal Factory 2: Robert Bosch (Malaysia) Address: Free Trade Zone 11900 Bayan Lepas, Penang Malaysia Factory 3: Bosch Automotive Products (Wuhu) Co., Ltd. Address: No. 88 Guandoumen Road, Jujiang District Wuhu City Anhui Province China CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 6 of 18 3. Equipment under test (EUT) 3.1. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) EUT A Multimedia Device PIVISBX0 with WLAN and 0001814 001 1052 S25 Bluetooth *) EUT short description is used to simplify the identification of the EUT in this test report. 3.2. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) AE 1 P-IVI USB Box USB Box -- -- -- P-IVI LVDS-Video- AE 2 Video-Generator -- -- -- Generator#02 AE 3 RF Splitter -- -- -- -- Load Box PIVI +2 AE 4 -- -- -- -- Meter Harness RJ 45 Dual Audio- Dual Audio-Video AE 5 -- -- -- Video Balun Balun RJ 45 Quad Audio- AE 6 Quad Audio-Balun -- -- -- Balun 8 Inch Display AE 7 PIVIDISP0 001 Module AE 8 Display Cable *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.3. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) EUT A + AE 1 + AE 2 + AE 3 + AE 4 + set. 1 Used for radiated measurements. AE 5 + AE 6 + AE 7 + AE 8 *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 7 of 18 3.4. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) CAN + GPS and op. 1 CAN + Broadcasting receiver (FM/ AM) and GPS activated broadcast RX mode EUT operating mode no. is used to simplify the test report. CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 8 of 18 4. Description of test system set-up’s 4.1. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2014 chapter 8, ANSI C63.10-2013 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 0.8 m height which is placed on the taining the EUT’s worst-case operation mode, cable turntable. By rotating the turntable (range 0° to position, etc. 360°, step 90°) and the EUT itself either on 3- orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical frequency orthogonal axis (defined operational position of is done to locate the frequency more precisely. After EUT) the emission spectrum and it’s this step, for all identified critical frequencies, the characteristics was recorded with an EMI- maximum peak was determined. receiver, broadband antenna and software. Following parameters were varied: the turntable Measurement antenna: horizontal and vertical, angle continuously in the range 0 to 360 degree, the heights: 1,0 m and 1,82 m as worst-case EUT itself either over 3-orthogonal axis (not determined by an exploratory emission defined usage position) or 2-orthogonal axis measurements. The results are documented in a (defined usage position). The measurement antenna diagram. Critical frequencies (low margin to height between 1 m and 4 m. limit) are saved within a table for further investigations. If various operating modes are On the determined worst-case position, a final supported, further investigations are made to find measurement with necessary bandwidth and the worst-case of them. Also the interconnection detector according standard has been carried out. cables and equipment position were varied in order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 9 of 18 4.2. Test system set-up for radiated electric field measurement above 1 GHz Specification: ANSI C63.4-2014 chapter 8, ANSI C63.10-2013 chapter 6.6 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a CISPR 16-4 compliant fully anechoic room (FAR) recognized by the regulatory commissions. The measurement distance was set to 3 meter for frequencies up to 18 GHz and 2 meter above 18 GHz. A bicon-log or horn antenna is used for frequency range 1 GHz to 40 GHz. Due to use of a fully anechoic room the measurement antennas are set to fixed antenna height of 1.55 m and the site validation criteria accord. CISPR 16-1-4:2010, Chapter 8.3 is fulfilled. The EUT is aligned within 3 dB beamwidth of the measurement antenna, on big EUTs several surface measurements are performed. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 1.55 m height which is placed on the taining the EUT’s worst-case operation mode, turntable. By rotating the turntable (range 0° to cable position, etc. 360°, step 15°) and the EUT itself either on 3- orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT) the emission spectrum and it’s precisely. After this step, for all identified critical characteristics was recorded with an EMI- frequencies, the maximum peak was determined. receiver, broadband antenna and software. The measurements are performed in horizontal Following parameters were varied: the turntable and vertical polarization of the measurement angle continuously in the range 0 to 360 degree, antennas. The results are documented in a the EUT itself either over 3-orthogonal axis (not diagram. Critical frequencies (low margin to defined usage position) or 2-orthogonal axis limit) are saved within a table for further (defined usage position). The measurement investigations. If various operating modes are antenna height is fixed to 1.55 m. supported, further investigations are made to find the worst-case of them. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA (1) EC = Electrical field – corrected value ER = Receiver reading M = LT - EC (2) M = Margin LT = Limit AF = Antenna factor CL = Cable loss DF = Distance correction factor (if used) GA = Gain of pre-amplifier (if used) All units are dB-units, positive margin means value is below limit. CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 10 of 18 5. Measurements 5.1. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz 5.1.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE Supply Voltage  via laptop  13.5VDC 5.1.2. Requirements/Limits FCC  Part 15 Subpart B, §15.109, class B  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205  RSS-Gen., Issue 5, Chapter 8.9, Table 5+7 (license-exempt radio apparatus)  RSS-Gen., Issue 5, Chapter 7.1.2, Table 4 (receiver) ISED  ICES-003, Issue 6, Table 5 (Class B)  RSS-247, Issue 1, Chapter 5 (DTS2.4GHZ Band)  C63.4-2014 ANSI  C63.10-2013 Radiated emissions limits, 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 54.0 5.1.3. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan, max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous tx-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 5.1.4. MEASUREMENT RESULTS The results are presented below in summary form only. For more information please see diagrams. Table of measurement results: Dia- Set- OP- Used detector Result gram Frequency range up mode Remark no. no. no. PK AV QP 3.01a 30 MHz – 1 GHz Set. 1 Op. 1 EUT laying    passed 3.01b 30 MHz – 1 GHz Set. 1 Op. 1 EUT standing    passed Remark: -- CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 11 of 18 5.2. General Limit - Radiated emissions, above 1 GHz 5.2.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab. 337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025 302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2  376 BBHA9120E  antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DCpower  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery 350 Car battery  Supply  via laptop  13.5VDC Voltage 5.2.2. Requirements/Limits  Part 15 Subpart B, §15.109 class B FCC  Part 15 Subpart C, §15.209 for frequencies defined in §15.205  Part 15 Subpart C, §15.407(b)(1)(2)(3)(4)  RSS-Gen., Issue 5, Chapter 8.9, Table 5+7 (transmitter licence excempt)  RSS-Gen., Issue 5, Chapter 8.9, Table 3 (receiver) ISED  ICES-003, Issue 6, Chapter 6.2.2, Table 7 (class B)  RSS-247, Issue 2, Chapter 6  C63.4-2014 ANSI  C63.10-2013 Limits Frequency AV AV Peak Peak [MHz] [µV/m] [dBµV/m] [µV/m] [dBµV/m] or [dBm/MHz] above 1 GHz for frequencies as defined in §15.205 500 54.0 5000 74.0 dBµV/m or RSS-Gen., Issue 5, §8.10 - Table 5 5.2.3. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW 1 MHz / 3 MHz Mode: Repetitive-Scan, max-hold Scan step 400 kHz Sweep-Time Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” 5.2.4. Measurement Results The results are presented below in summary form only. For more information please see diagrams. Set- OP- Used detector Result Diagram Frequency up mode Remark no. range no. no. PK AV QP 4.01a 1 – 18 GHz Set. 1 Op. 1 --    passed 4.01b 18 – 26GHz Set. 1 Op. 1 --    passed Remark: -- CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 12 of 18 5.3. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based on a RF-Measurement Reference Frequency range Remarks confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Substitution Power Output radiated - 30 MHz - 4 GHz 3.17 dB method Cel- Cel- Set-up No. BT1 W1 W2 -- C1 C2 Power Output conducted - 9 kHz - 12.75 GHz N/A 0.60 0.7 0.25 N/A -- - 12.75 - 26.5GHz N/A 0.82 -- N/A N/A -- Conducted emissions - 9 kHz - 2.8 GHz 0.70 N/A 0.70 N/A 0.69 -- N/A - not on RF-port 2.8 GHz - 12.75GHz 1.48 N/A 1.51 N/A 1.43 -- applicable 12.75 GHz - 18GHz 1.81 N/A 1.83 N/A 1.77 -- 18 GHz - 26.5GHz 1.83 N/A 1.85 N/A 1.79 -- Power density - 1 – 2.8GHz 1.40 dB -- 0.1272 ppm (Delta Marker) Frequency Occupied bandwidth - 9 kHz - 4 GHz error 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency Emission bandwidth 9 kHz - 4 GHz error - See above: 0.70 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic Radiated emissions 30 MHz - 1 GHz 4.2 dB field - Enclosure 1 GHz - 20 GHz 3.17 dB E-field Substitution Table: measurement uncertainties, valid for conducted/radiated measurements CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 13 of 18 6. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV , AVG, CAV Average detector EIRP Equivalent isotropically radiated power, determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission, USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification, Dokuments from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) FCC, Federal Communications (MRA US-EU 558 Radiated Measurements above 1 GHz, 3 m (FAR) Commission 0003) 348 Mains Ports Conducted Interference Measurements Laboratory Division, USA 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R-20013 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G-20013 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C-20009 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T-20006 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 14 of 18 8. Instruments and Ancillary the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 607 Signal Generator SMR 20 832033/011 V1.25 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 670 Univ. Radio Communication Tester CMU 200 106833 µP1 =V8.50, Firmware = V.20 689 Vector Signal Generator SMU200 100970 02.20.360.142 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 15 of 18 8.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 16.05.2019 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 16.05.2019 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 16.05.2019 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 15.05.2019 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 30.05.2019 36/12 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO - 31.07.2021 M 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.05.2021 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 15.05.2019 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.05.2021 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.05.2021 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 RT Harmonics Analyzer dig. 119 B10 G60547 BOCONSULT 36 M - 30.05.2019 Flickermeter 133 horn antenna 18 GHz (Meas 1) 3115 9012-3629 EMCO 36 M 1c 10.03.2020 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 36 M - 10.03.2020 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2020 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2019 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 30.05.2019 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2020 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2020 WRCA 800/960- 267 notch filter GSM 850 9 Wainwright GmbH pre-m 2 6EEK 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 Model 47 (10 dB) 50 274 attenuator (10 dB) 50 W BG0321 Weinschel pre-m 2 W 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 17.05.2019 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 14.03.2020 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 20.03.2020 331 Climatic Test Chamber -40/+180 Grad HC 4055 43146 Heraeus Vötsch 24 M - 30.10.2019 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2020 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 17.05.2019 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 24.05.2019 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 17.05.2019 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 30.05.2019 389 Digital Multimeter Keithley 2000 0583926 Keithley pre-m - 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 30.06.2019 LUFFT Mess u. 405 Thermo-/Hygrometer OPUS 10 THI 126.0604.0003.3.3.3.22 24 M - 30.03.2019 Regeltechnik GmbH 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 06.03.2019 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 10.03.2020 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.05.2019 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2020 CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 16 of 18 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.05.2019 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2021 Automotive Cons. 477 ReRadiating GPS-System AS-47 - - 3 Fink 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 16.05.2019 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d System CTC NSA-Verification SAR- System EMI field ETS Lindgren / 487 - 24 M - 31.03.2019 EMI (SAR) NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 30.06.2019 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- WRCG 824/849- 503 band reject filter SN 5 Wainwright pre-m 2 814/859-60/10SS HF Relais Box 517 relais switch matrix SE 04 Keithley pre-m 2 Keithley System 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 18.05.2019 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 10 dB Broadband resistive power 530 R 416110000 LOT 9828 - pre-m 2 divider 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.07.2019 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 30.07.2019 36/12 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz - 31.07.2021 M System CTC S-VSWR Verification System EMI Field ETS 550 - 24 M - 30.03.2019 SAR-EMI SAR S-VSWR Lindgren/CETECOM System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 08.08.2019 VSWR 36/12 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia - 31.03.2019 M 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 594 Wideband Radio Communication Tester CMW 500 101757 Rohde & Schwarz 12 M - 30.05.2019 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 17.05.2019 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 15.05.2019 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 R416120000 20dB 613 Attenuator Lot. 9828 Radiall pre-m 2 10W 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2020 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 30.05.2019 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 Generic Test Load 625 Generic Test Load USB - CETECOM - 2 USB 627 data logger OPUS 1 201.0999.9302.6.4.1.43 G. Lufft GmbH 24 M - 30.03.2019 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 HDMI cable with 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 Ethernet 1m HDMI cable with 638 HDMI Kabel with Ethernet 1,5 m flach - Reichelt - 2 Ethernet 1,5m 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 Certified HDMI cable 641 HDMI cable with Ethernet - PureLink - 2 with 642 Wideband Radio Communication Tester CMW 500 126089 Rohde&Schwarz 24 M - 24.05.2019 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2020 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.05.2019 Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 29.03.2019 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.05.2019 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 24 M - 16.05.2019 691 OSP120 Base Unit OSP120 106833 Rohde & Schwarz 12 M - 30.05.2019 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 29.05.2020 CTC-Radio Lab 693 TS8997 - Rohde&Schwarz 12 M 5 30.05.2019 1_TS8997 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 701 CMW500 wide. Radio Comm. CMW500 158150 Rohde & Schwarz 12 M - 30.07.2019 MA 4010-KT080- MA4170-KT100-XPET- 703 INNCO Antennen Mast INNCO pre-m - XPET-ZSS3 ZSS3 CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 17 of 18 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due INNCO Systems 704 INNCON Controller CO 3000-4port CO3000/933/38410516/L pre-m - GmBh 711 Harmonic Mixer 90 GHz - 140GHz RPG FS-Z140 101004 RPG 36 M - 22.02.2020 712 Harmonic Mixer 75 GHz - 110GHz FS-Z110 101468 Rohde & Schwarz 36 M - 22.02.2020 713 Harmonic Mixer, 50 GHz - 75GHz FS-Z75 101022 Rohde & Schwarz 36 M - 22.05.2020 714 Signal Analyzer 67GHz FSW67 104023 Rohde & Schwarz 24 M - 28.02.2020 RPG Radiometer 715 Harmonic Mixer, 140 GHz - 220GHz FS-Z220 101009 36 M - 03.08.2020 Physics RPG Radiometer 716 Harmonic Mixer 220 GHz to 325 GHZ FS-Z325 101005 36 M - 13.02.2020 Physics 747 Spectrum Analyzer FSU 26 200152 Rohde & Schwarz 12 M - 30.05.2019 748 Pickett-Potter Horn Antenna FH-PP 4060 010001 Radiometer Physiscs 36 M - 749 Pickett-potter Horn Antenna FH-PP 60-90 010003 Radiometer Physics - - 750 Pickett-Potter Horn Antenna FH-PP 140-220 010011 Radiometer Physics - - optoCAN-FD mk-messtechnik 751 Digital Optical System 17-010416 - - Transceiver GmbH optoCAN-FD mk-messtechnik 752 Digital Optical System 17-010083 - - Transceiver GmbH optoCAN-FD mk-messtechnik 753 Digital Optical System 17-010084 - - Transceiver GmbH optoCAN-FD mk-messtechnik 754 Digital Optical System 17-010415 - - Transceiver GmbH optoLAN-100-MAX mk-messtechnik 755 Digital Optical System 17-010795 - - Transceiver GmbH 758 Signal Generator SMU 200A 100754 Rohde & Schwarz 24 M - 11.10.2019 780 Spectrum Analyzer FSH3 101726 Rohde & Schwarz 24 M - 19.07.2019 Elektro-Automatik 781 Power Supply PS 2042-10 B 2815450369 - - GmbH &Co.KG lektro-Automatik 782 Power Supply PS 2042-10 B 2815450348 - - GmbH &Co.KG 783 Spectrum Analyzer FSU 26 100414 Rohde & Schwarz 12 M - 30.05.2019 784 Power Supply NGSM 32/10 00196 Rohde & Schwarz 12 M - RF Step Attenuator 785 RSP 860712/012 Rohde & Schwarz 12 M - 0…139.9dB 786 SAR Probe ES3DV3 3340 Speag 36 M - 14.02.2021 787 OSP OSP B157WX 101264 Rohde & Schwarz 12 M - 30.05.2019 Seibersdorf 788 Precision Omnidirectional Dipole POD 618 6182558/Q 36 M - 30.06.2021 Labaratories Seibersdorf 789 Precision Omnidirectional Dipole POD 16 162496/Q 36 M - 30.06.2021 Laboratories CETECOM_TR18-1-0200901T08a-C1

Test Report 18-1-0200901T08a-C1, Page 18 of 18 8.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months. between this every 12 months internal validation 36/12 M Calibration every 36 months. between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 9. Versions of test reports (change history) Version Applied changes Date of release -- Inital release 2018-12-28 C1 Administrative Data and EUT Type updated 2019-01-24 END OF TEST REPORT CETECOM_TR18-1-0200901T08a-C1


Document Created: 2019-01-24 14:55:59
Document Modified: 2019-01-24 14:55:59
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC