test report - DSS (BT) - full

FCC ID: YBN-LCN2K70C10

Test Report

Download: PDF
FCCID_2725279

TEST REPORT No.: 6-0461-14-3-1e-C1 According to: FCC Part 15.247 for Robert Bosch Car Multimedia GmbH LCN2K70B10 Radio Navigation System (Bluetooth 2.4GHz) FCC ID: YBN-LCN2K70B10 Laboratory Accreditation and Listings Voluntary Controls for Industry Canada Electromagnetic Emissions Reg. No.: 3462D-1 Reg. No.: MRA US-EU 0003 Reg. No.: 3462D-2 R-2666 C-2914, Reg. No.: 3462D-3 T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 33 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 6-0461-14-3-1e-C1, Page 2 of 33 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. Tests measurement overview according of US FCC CFR47, Part 15C Standards .......................................... 3 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant’s details ........................................................................................................................................... 5 2.5. Manufacturer’s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Technical data of main EUT declared by applicant ......................................................................................... 6 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 7 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 7 3.4. EUT set-ups ..................................................................................................................................................... 7 3.5. EUT operating modes ...................................................................................................................................... 8 3.6. Configuration of cables used for testing .......................................................................................................... 8 3.7. Test system set-up for conducted RF-measurements at antenna port .............................................................. 9 3.8. Test system set-up for radiated magnetic field measurements below 30 MHz ................................................ 10 3.9. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz ............................................... 11 3.10. Test system set-up for radiated electric field measurement above 1 GHz ..................................................... 12 4. MEASUREMENTS ............................................................................................................................................. 13 4.1. RF-Parameter - 20 dB Bandwith ..................................................................................................................... 13 4.2. RF-Parameter - Channel carrier frequency separation for FHSS-systems ....................................................... 15 4.3. RF-Parameter - Time of occupancy for FHSS systems ................................................................................... 16 4.4. RF-Parameter - Specification for hopping channel numbers for FHSS systems ............................................. 17 4.5. RF-Parameter - 20 dBc power specification .................................................................................................... 18 4.6. RF-Parameter – RF Power conducted.............................................................................................................. 20 4.7. General Limit - Radiated field strength emissions below 30 MHz .................................................................. 22 4.8. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz .............................................................. 24 4.9. General Limit - Radiated emissions, above 1 GHz .......................................................................................... 26 4.10. RF-Parameter - Radiated Band Edge compliance measurements .................................................................. 27 4.11. Measurement uncertainties ............................................................................................................................ 29 5. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 29 6. INSTRUMENTS AND ANCILLARY ................................................................................................................ 30 6.1. Used equipment “CTC” ................................................................................................................................... 30 7. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................. 33 Table of annex Total pages Annex 1: Test set-up photographs - separate document TR6-0461-14-3-1e –A1 6 Annex 2: Measurement diagrams - separate document TR6-0461-14-3-1e –A2 63 Annex 3: External EUT photographs - separate document TR6-0461-14-3-1e –A3 16 Annex 4: Internal EUT photographs - separate document TR6-0461-14-3-1e –A4 8 TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 3 of 33 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The presented Equipment Under Test (in this report, hereinafter referred as EUT) integrates a Bluetooth© transmitter. Other implemented wireless technologies are not considered within this test report. Following test cases have been performed to show compliance with applicable FCC Part 2 and Part 15 rules of the FCC CFR Title 47 Rules, Edition 4th November 2014 standards. 1.1. Tests measurement overview according of US FCC CFR47, Part 15C Standards References and Limits EUT EUT Test cases Port op. Result FCC Standard Test limit set-up mode TX-Mode Radio Enclosure + “general frequency §1.1307(b) Interconnecting population/uncontrolled exposure §2.1091 2 1 passed cables environment” requirements §2.1093 (radiated) Table 1 (MPE) 20 dB 2 1 bandwidth Antenna §15.247 At least 25 kHz or 2/3 of terminal passed Channel carrier (a)(1) 20 dB bandwith (conducted) frequency 2 2 separation Antenna 99% occupied terminal -- 99% Power bandwidth 2 1 passed bandwidth (conducted) Channel average Antenna §15.247 Occupancy time terminal 0.4 seconds 2 2 passed (a)(1) (iii) and number of (conducted) channels Transmitter Antenna §15.247 Peak output terminal < 125 mW 2 1 passed (b)(1) power (conducted) TR6-0461-14-3-1e-C1

m Test Report 6—0461—14—3—1e—C1, Page 4 of33 ct”com . 125 mW (EIRP) for reapouet eak output Enclosure : g15247 antenna with i directional 1 1 passed f power radiated (radiated) (b)@) gain less o 46y Out—Of—Band 20 dBc and Emissions in RF— emissions Antenna §15247 restricted bands must terminal ("” meet the general 2 1 passed Band—Edge (conducted) fieldstrength radiated emissions limits CHoim,qr® Enclosure+ pasny Emissions in restricted avengl + emissions Interconnecting $HELE §15.205 bands must meet the 1 1 passed restaed cables 13200 general field—strength Sends (radiated) * radiated limits AC—Power Lines FCC §15.107 AC]‘;:"" §15.207 class B limits s x N/A Conducted §15.207 limits Emissions Remark : N/A: not applicable NT: not tested The current version ofthe Test Report 6—0461—14—3—1e—C1 replaces the Test Report 6—0461—14—3—1e dated 2015—05—20. The replaced Test report is herewith invalid. CETECOM " omm im Teelbruch 116 smcs 45219 Essen j /’ ~, Tel: + 49 i0) 20 i, %/\—/ > Fax: + 40 (0) — Dipl.—Ing. Ch. Lorenz M. Nunier Responsible for test section Responsible for test report TRé0461—14—3—1e—C

Test Report 6-0461-14-3-1e-C1, Page 5 of 33 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Project leader: Dipl.-Ing N. Perez Responsible for test report: M. Nunier Receipt of EUT: 2015-03-18 Date(s) of test: 2015-03-24 to 2015-05-13 Date of report: 2015-07-14 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: Robert Bosch Car Multimedia GmbH Address: Robert-Bosch-Straße 200 31132 Hildesheim Germany Contact person: Mr. Dirk Zamow 2.5. Manufacturer’s details Manufacturer’s name: please see Applicant's details Address: please see Applicant's details TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 6 of 33 3. Equipment under test (EUT) 3.1. Technical data of main EUT declared by applicant Main function Radio Navigation System Type LCN2K70B10 Frequency range and channels 2402 MHz to 2480 MHz  Ch. 0 to Ch. 78  Ch. 0 to Ch. 40 (US/Canada -bands) Type of modulation (packet types)  BT 1.0 / BT 1.1: DH1/DH3/DH5 – GFSK  BT 2.0 / BT 2.1: DH1/2DH3/2DH5 – Pi/4 DQPSK 3DH1/3DH3/3DH5 – 8DPSK  BT 3.0: same as BT 2.1 + MAC/PHY DATA  BT 4.0: DH1/DH3/DH5 – GFSK Number of channels  0 to 78 (USA/Canada -bands)  0 to 40 Antenna Type  Integrated  External, no RF- connector  External, separate RF-connector Antenna Gain 4.2dBi gain maximum in 2.4 GHz band Nominal output power 4dBm (Bluetooth power class 2) FCC-ID YBN-LCN2K70B10 Installed options  GPS (not tested within this test report)  FM-Radio (Receiver only) Power supply  DC power only: 13.5 Volt Special EMI components -- EUT sample type  Production  Pre-Production  Engineering Firmware  for normal  Special version for test execution use FCC label attached  yes  no TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 7 of 33 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware software status tion*) status Radio Navigation EUT A LCN2K70B10 3130494 051 F014 System Radio Navigation EUT B LCN2K70B10 3130476 051 F014 System *) EUT short description is used to simplify the identification of the EUT in this test report. 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) AE 1 Main Wiring long TH24HW-CS2 #1 -- -- AE 2 USB Harness USCAR30 #11 -- -- AE 3 USB Harness TCU-USB #12 -- -- AE 4 Main Wiring short TH18HW-CS2 #2 -- -- AE 5 Ignition Unit Nissan LCN2 #1 -- -- AE 6 GPS-Antenna GPS #1 -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) EUT A + AE 1 + AE 2 + AE 3 + AE 4 + set. 1 Used for radiated tests AE 5 + AE 6 set. 2 EUT B + AE 1+ AE 4 + AE 5 Used for conducted tests *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 8 of 33 3.5. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) With help of special test firmware (special HMI version F016) a op. 1 Bluetooth signal was transmitted continuously by the EUT. The choice TX-Mode of modulation schemes and channels are possible. See spcial document from aplicant “Short Start-Up instruction ..” With help of special test firmware a connection could be established to a op. 2 TX-Mode hopping on Bluetooth base simulator. (R&S CBT32). Hopping mode was activated with help of a Bluetooth base simulator. (R&S CBT32) *) EUT operating mode no. is used to simplify the test report. 3.6. Configuration of cables used for testing Cable S/N HW Cable length number Item Type serial number hardware status Cable 1 Main Wiring long #1 -- 2m Cable 2 USB Harness #11 -- 2m Cable 3 USB Harness See §3.3 #12 -- 2m Cable 4 Main Wiring short #2 -- 1m Cable 5 GPS Antenna #1 0.36m TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 9 of 33 3.7. Test system set-up for conducted RF-measurements at antenna port Specification: ANSI C63.10-2009 General Description: The EUT‘s RF-signal is first attenuated before it is connected to the input of the RF-coupler. The direct output branch is connected to the spectrum – analyzer, the coupled branch to the communication tester. The specific attenuation is determined prior to the measurement within a set-up calibration. The value is taken into account by correcting the measurement readings on the spectrum- analyzer either by a transducer factor (TDF) or an relative offset to reference level. Schematic: Testing method: According to ANSI 63.10-2009 for each individual test, see more details in each chapter. TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 10 of 33 3.8. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.4-2009 chapter 8.2.1, ANSI C63.10-2009 chapter 6.4 General Description: Evaluating the radiated field emissions are done first by an exploratory emission measurement and a final measurement for most critical frequencies determined. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commission. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (step cable position, etc. 90°, range 0°to 360°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT), the emission spectrum was recorded. The precisely. After this step, for all identified critical loop antenna was moved at least to frequencies, the maximum peak was determined. 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to Following parameters were varied: the turntable maximize the emissions. The results are angle continuously in the range 0 to 360 degree, documented in a diagram. Critical frequencies the EUT itself either over 3-orthogonal axis (not (low margin to limit) are saved within a data defined usage position) or 2-orthogonal axis reduction table for further investigations. If (defined usage position). various operating modes are supported, further investigations are made to find the worst-case. On the determined worst-case position, a final Also the interconnection cables and equipment measurement with necessary bandwidth and position were varied in order to maximize the detector according standard has been carried out. emissions. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors: IEEC Transaction EMC, Vol. 47, No. 3 , Aug. 2005, Journal Paper “Extrapolating Near-field emissions of low frequency loop transmitters”. TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 11 of 33 3.9. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2009 chapter 8, ANSI C63.10-2009 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (range cable position, etc. 0° to 360°, step 90°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT) the emission spectrum and it’s precisely. After this step, for all identified critical characteristics was recorded with an EMI- frequencies, the maximum peak was determined. receiver, broadband antenna and software. Following parameters were varied: the turntable Measurement antenna: horizontal and vertical, angle continuously in the range 0 to 360 degree, heights: 1,0 m and 1,82 m as worst-case the EUT itself either over 3-orthogonal axis (not determined by an exploratory emission defined usage position) or 2-orthogonal axis measurements. The results are documented in a (defined usage position). The measurement diagram. Critical frequencies (low margin to antenna height between 1 m and 4 m. limit) are saved within a table for further investigations. If various operating modes are On the determined worst-case position, a final supported, further investigations are made to find measurement with necessary bandwidth and the worst-case of them. Also the interconnection detector according standard has been carried out. cables and equipment position were varied in order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. TR6-0461-14-3-1e-C1

Test Report 6—0461—14—3—1e—C1, Page 12 of 33 CETECOM* n 3.10. Test system set—up for radiated electric field measurement above 1 GHz Specification: ANSI C63.4—2009 chapter 8, ANSI C63.10—2009 chapter 6.6 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a CISPR 16—4 compliant fully anechoic room (FAR) recognized by the regulatory commissions. The measurement distance was set to 3 meter for frequencies up to 18 GHz and 2 meter above 18 GHz. A bicon—log or hom antenna is used for frequency range 1 GHz to 40 GHz. Due to use of a fully anechoic room the measurement antennas are set to fixed antenna height of 1.55 m and the site validation criteria accord. CISPR 16—1—4:2010, Chapter 8.3 is fulfilled. The EUT is aligned within 3 dB beamwidth of the measurement antenna, on big EUT‘s several surface measurements are performed. Schematic: 3neter turntable Log.per. dipol antenna Anechoic Room 1 or 3 meters data link PC + Software Testing method: Exploratory, preliminary measurements Final measurementon criticalfrequencies The EUT and its associated accessories are Based on the exploratory measurements, the most placed on a non—conductive position manipulator critical frequencies are re—measured by main— (tipping device) of 1.55 m height which is placed taining the EUT‘s worst—case operation mode, on the turntable. By rotating the turntable. (range cable position, etc. 0° to 360°, step 15°) and the EUT itself either on 3—orthogonal axis (portable equipment} or 2— First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT} the emission spectrum and it‘s precisely. After this step, for all identified critical characteristies was recorded with an EMI— frequencies, the maximum peak was determined. receiver, broadband antenna and software. The measurements are performed in horizontal Following parameters were varied: the turntable and vertical polarization of the measurement angle continuously in the range 0 to 360 degree, antennas. The results are documented in a the EUT itself either over 3—orthogonalaxis (not diagram. Critical frequencies (low margin to defined usage position} or 2—orthogonal axis limit) are saved within a table for further (defined usage position}. The measurement investigations. If various operating modes are antenna height is fixed to 1.55 m. supported, further investigations are madeto find the worst—case of them. Also the interconnection On the determined worst—case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: Ec=Er + AF + C+Dr— Ga (1) Ec = Electrical field — corrected value Er = Receiver reading M=Lt— Ee (2) M = Margin Ly=Limit AF = Antenna factor C1 = Cable loss Dr= Distance correction factor (if used) Ga = Gain of pre—amplifier (if used) All units are dB—units, positive margin means value is below limit. TR6—0461—14—3—1e—C1

Test Report 6-0461-14-3-1e-C1, Page 13 of 33 4. Measurements 4.1. RF-Parameter - 20 dB Bandwith 4.1.1.Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.  receiver  377 ESCS30  001 ESS  489 ESU   otherwise  530 10dB Att.  613 20dB Att.   cable K4  Directional Coupler 1539R-10 4.1.2. Requirements: FCC  §15.247 (a) (1) (1) Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 kHz or the 20 dB bandwidth of the hopping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.5 MHz band may have Remark hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW. (2) DSSS Systems using digital modulation techniques may operate in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 4.1.3. EUT settings For FHSS-systems hopping mode was switched-off so fixed three different channels could be measured. The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 4.1.4. Measurement method The measurement was performed with the RBW set to 10kHz. The span was set to cover the complete carrier. Three carrier frequencies (low/middle/high) were used for showing the compliance with this requirement. A DELTA Marker method was set to measure the bandwidth compared to the highest In-Band power. The operating modes have been varied (e.g. data rate, modulation scheme, etc.). The hopping-mode is switched off. 4.1.5. Spectrum-Analyzer Settings Span Set as to fully display the emissions and approximate 20dB below the PEAK level Resolution Bandwidth Set to approx 1% …3% of the emission width (RBW) Video Bandwidth (VBW) 3 times the resolution bandwidth Sweep time Coupled and low enough to have no gaps within power envelope Detector Sample (if bin width: Span/no. of frequency points SA < 0.5*RBW SA otherwise Peak detector) Sweep mode Repetitive Mode, Max hold TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 14 of 33 4.1.6. Results: DH3 packet type (GFSK-Modulation) Set-up no.: 2 20 dB Bandwidth Op. mode: 1 [kHz] TNom = 21°C Low channel = 0 Middle channel =39 High channel = 78 VNom = 13.5 V (2402 MHz) (2441 MHz) (2480 MHz) Maximum Value 932.69 927.88 932.69 Remark: see diagrams in separate annex 2 2DH3 Packet type (Pi/4-QPSK Modulation) Set-up no.: 2 20 dB Bandwidth Op. mode: 1 [kHz] TNom = 21°C Low channel = 0 Middle channel =39 High channel = 78 VNom = 13.5 V (2402 MHz) (2441 MHz) (2480 MHz) Maximum Value 1317.31 1317.31 1312.50 Remark: see diagrams in separate annex 2 3DH5 packet type (8DPSK Modulation) Set-up no.: 2 20 dB Bandwidth Op. mode: 1 [kHz] TNom = 21°C Low channel = 0 Middle channel =39 High channel = 78 VNom = 13.5 V (2402 MHz) (2441 MHz) (2480 MHz) Maximum Value 1274.04 1274.04 1274.04 Remark: see diagrams in separate annex 2 4.1.7. Verdict: pass TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 15 of 33 4.2. RF-Parameter - Channel carrier frequency separation for FHSS-systems 4.2.1.Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU    spectr. analys.  381 380 FSBS  120 FSEM  264 FSEK    otherwise  530 10dB Att.  613 20dB Att.   cable K4  cable K5 4.2.2. Requirements: FCC  §15.247 (a) (1) (1) FHHS Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 kHz or the 20 dB bandwidth of the hopping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB Remark bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW. (2) DSSS Systems using digital modulation techniques may operate in the 902-928 MHz, 2400- 2483.5 MHz, and 5725-5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 4.2.3. EUT settings For FHSS-systems hopping mode was switched-off so fixed three different channels could be measured. The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 4.2.4. Measurement method The measurement to prove this requirement was performed with a low RBW of 100kHz, peak detector and trace Hold-Max function in order to resolve each frequency carrier separately. The span of the frequency analyzer was set to cover the carrier investigated as well as its neighbour channels. A frequency DELTA Marker method was set to measure the frequency separation between the channels. 4.2.5. Limits Either: 1. 25 kHz or 20dB BW or 2. 25kHz and 2/3of BW if Power<125mW 4.2.6. Measurement Results Set-up no.: 2 Channel separation Op. mode: 2 TNom = 21°C Measured around middle channel VNom = 13.5 V (2441 MHz) Measured Result valid for DH5 and 3DH5 >1MHz Applicants declared value 1 MHz according BT-core spec. Remark: see diagrams enclosed in annex 2 for different modulations 4.2.7. Result: passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 16 of 33 4.3. RF-Parameter - Time of occupancy for FHSS systems 4.3.1.Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU    spectr. analys.  381 380 FSBS  120 FSEM  264 FSEK    otherwise  530 10dB Att.  613 20dB Att.   cable K4  cable K5 4.3.2. Requirements: FCC  §15.247 (a) (1) iii Frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 Remark seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. Frequency hopping systems may avoid or suppress transmissions on a particular hopping frequency provided that a minimum of 15 channels are used. 4.3.3. Method for measuring the occupancy time: The measurement was performed with a spectrum analyzer set to ZERO span. The device was set to work within the defined specification with frequency hopping mode to on. The spectrum-analyzer was set the MAX-Hold positive peak detector mode. The sweep time set as long as necessary to capture the full signal burst per hopping channel. The burst on-period is captured by setting appropriate markers in the rising and falling edges. 4.3.4. Calculations: Formula for calculating the dwell time (pseudo-hopping sequence over all channels assumed): Average Dwell Time: Timeslot length  Hop rate  time period number of hopping channels For Bluetooth® following is valid: The maximum staying time of 0.4 seconds within a 31.6 second period in data mode is constant for Bluetooth® devices and independent from the packet type. For longer packet types the hopping data rate is reduced according the packet type length in order to comply with this requirement. Calculated according mentioned-above formula: Hop rate per Packet types Hop rate[1/s] Channels Time period Transmissions channels DH1/2DH1/3DH1 1600 20.25 640 DH3/2DH3/3DH3 533,33 79 6.75 31.6 214 DH5/2DH5/3DH5 320 4.05 128 4.3.5. Measurement results. Set-up 1, Op. Mode 2 Measured pulse width for different packet types/modulations (see annex 2 for diagrams): Average Dwell time [ms] Packet types PulseWidth Transmissions (approx transmissions on one channel per one milli second) DH1 387.82 µs 640 248.2048 DH3 1.6458 ms 214 352.2012 DH5 2.8958 ms 128 370.6624 2DH1 397.1152 µs 640 254.1537 2DH3 1.6538 214 353.9132 2DH5 2.9038 ms 128 371.6864 3DH1 403.8461 µs 640 258.4615 3DH3 1.6538 ms 214 353.9132 3DH5 2.8958 ms 128 370.6624 Remarks: table shows only maximum values, for more details please see annex 2 4.3.6. Test result passed < 400 msec TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 17 of 33 4.4. RF-Parameter - Specification for hopping channel numbers for FHSS systems 4.4.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU    spectr. analys.  489 ESU  120 FSEM  264 FSEK  489 ESU   power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise 613 20dB Attenuator  cable K4 4.4.2. Requirements: FCC  §15.247 (a) (1) iii Frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels Remark employed. Frequency hopping systems may avoid or suppress transmissions on a particular hopping frequency provided that a minimum of 15 channels are used. (2) DSSS Systems using digital modulation techniques may operate in the 902-928 MHz, 2400- 2483.5 MHz, and 5725-5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 4.4.3. Method for measurement of the channel numbers: The measurement was performed with spectrum analyzer’s RBW set to 300kHz. The device was set to work within the defined specification with frequency hopping mode set to on. The spectrum-analyzer was set to MAX-Hold positive peak detector mode. After a trace stabilization period the trace is recorded and the number of channels counted. 4.4.4. Results Set-up no. 1 Number of channels Op. Mode 2 TNOM = 21°C 79 VNOM = 13.5V Remark: see diagrams enclosed in the separate annex A2 Checked for DH5, 2DH5 and 3DH5 packet types RESULT: passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 18 of 33 4.5. RF-Parameter - 20 dBc power specification 4.5.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  443 System CTC-FAR-EMI-  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU    spectr. analys.  489 ESU  120 FSEM  264 FSEK    power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  613 20 dB Attenuator  cable K4 4.5.2. Reference: §15.247, §15.205, RSS-210: A8.5 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. 4.5.3. EUT settings: For FHHS-systems hopping mode was switched-off so fixed three different channels could be measured.The EUT was instructed to send with maximum power (if adjustable) according to applicants instructions. 4.5.4. Measurement method: The frequency spectrum was investigated for conducted spurious emissions values lower than 20dB related to the RF-carrier power value. Three carrier frequencies (low/middle/high channel) were used for showing the compliance with this requirement. The detector were chosen according §15.209(d). The video bandwidth (VBW) was chosen 10 times the resolution bandwidth (RBW). The frequency scan was up to 10 times the highest channel frequency within the operational mode. The spectrum-analyzer was set to MAX-PEAK Detector, MAX-Hold Mode. For FHSS-systems hopping mode was switched-off so fixed three different channels could be measured. The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. 4.5.5. Results: 4.5.5.1. DH5-Packet type (GFSK-Modulation) Set-up no.: 2 RF-Conducted test: 20 dBc spurious emissions Op-Mode: 1 Low channel =0 Middle channel = 39 High channel = 78 (2402 MHz) (2441 MHz) (2480 MHz) Level Reference Level Reference Level Reference Frequency (In-Band) = -0.8 dBm (In-Band) = -1.27 dBm (In-Band) = -2.49 dBm Range Limit= -20.8 dBm Limit= -21.27 dBm Limit= -22.49 dBm Frequency Value Frequency Value Frequency Value [MHz] [dBc] [MHz] [dBc] [MHz] [dBc] 150 kHz to >30 >30 >30 30MHz No No No 30MHz to 2.8 remarkable >30 remarkable >30 remarkable >30 GHz peaks found peaks found peaks found 2.8 to 18 GHz >25 >25 >25 18 to 25 GHz >25 >25 >25 Band-Edge -- >49.87 -- -- >46.37 (Hopping mode) Remark: see diagrams in annex 2 The limit on the diagrams is 20dB under the reference level measured In-Band for each channel TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 19 of 33 4.5.5.2. 2DH5-Packet type (PI/4-DQPSK Modulation) Set-up no.: 2 RF-Conducted test: 20 dBc spurious emissions Op-Mode: 1 Low channel =0 Middle channel = 39 High channel = 78 (2402 MHz) (2441 MHz) (2480 MHz) Level Reference Frequency (In-Band)= 0.23 dBm Range Limit= -19.77 dBm Frequency Value Frequency Value Frequency Value [MHz] [dBc] [MHz] [dBc] [MHz] [dBc] 150 kHz to >30 30MHz No 30MHz to 2.8 Not Not remarkable >30 -- -- GHz performed performed peaks found 2.8 to 18 GHz >25 18 to 25 GHz >25 Band-Edge -- >44.69 -- -- >47.62 (Hopping mode) Remark: see diagrams in annex 2 The limit on the diagrams is 20dB under the reference level measured In-Band for each channel Only channel 0 performed, not critical modulation scheme 4.5.5.3. 3DH5-Packet type (8DPSK-Modulation) Set-up no.: 2 RF-Conducted test: 20 dBc spurious emissions Op-Mode: 1 Low channel =0 Middle channel = 39 High channel = 78 (2402 MHz) (2441 MHz) (2480 MHz) Level Reference Level Reference Level Reference Frequency (In-Band) = 0.26 dBm (In-Band) = -0.13 dBm (In-Band) = -1.23 dBm Range Limit= -19.74 dBm Limit= -20.13 dBm Limit= -21.23 dBm Frequency Value Frequency Value Frequency Value [MHz] [dBc] [MHz] [dBc] [MHz] [dBc] 150 kHz to No >30.0 -- >30.0 -- >30.0 30MHz remarkable 30MHz to 2.8 peaks found >30.0 >30.0 >30.0 -- -- GHz 2.8 to 18 GHz >25.0 -- >30.0 -- >25.0 18 to 25 GHz >25.0 -- >30.0 -- >25.0 Band-Edge -- >39.92 -- -- >49.19 (Hopping mode) Remark: see diagrams in annex 2 The limit on the diagrams is 20dB under the reference level measured In-Band for each channel 4.5.6. Verdict: passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 20 of 33 4.6. RF-Parameter – RF Power conducted 4.6.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  443 System CTC-FAR-EMI-  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU    spectr. analys.  489 ESU  120 FSEM  264 FSEK    power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  613 20dB Attenuator  Directional Coupler 1539R-10 4.6.2. Requirements:  §15.247 (b) (1) for FHSS Bluetooth FCC  §15.247 (b) (3) for DSSS  C63.10-2009 (chapt 6.101) (for FHSS Bluetooth) ANSI  C63.10-2009 (chapt 6.102) 4.6.3. Reference: EUT antenna characteristics:  Directional Gain < 6 dBi (measured: difference between measured conducted and radiated eirp. power)  Directional Gain > 6 dBi (measured / applicant’s declaration) -> conducted power reduction necessary 4.6.4. EUT settings: For FHHS-systems hopping mode was switched-off so fixed three different channels could be measured. The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 4.6.5. Measurement method: The measurement was performed in non-hopping transmission mode with the carrier set to lowest/middle and highest channel. The power was also checked for different data rates, modulation scheme or packet types if applicable. TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 21 of 33 4.6.6. Settings on Spectrum-Analyzer: Center Frequency Nominal channel frequency Span 25 MHz Resolution Bandwidth (RBW) 5 MHz > 20dB-Bandwidth of the signal Video Bandwidth (VBW) 3 times the resolution bandwidth = 10MHz Sweep time coupled Detector Peak, Max hold mode Sweep Mode Repetitive mode 4.6.7. Conducted measurement: Max. Peak Power  Maximum declared antenna gain [isotropical]: 4.2dBi < 6dBi accord. standard  Rated nominal power: Bluetooth Power Class 2 - 4dBm (2.51mW) MAX PEAK POWER (conducted) Set-up no.: 1 Packet Low channel = 0 Middle channel = 39 High channel = 78 Op-Mode: 1 type (2402 MHz) (2441 MHz) (2480 MHz) DH5 -0.42 -0.79 -2.02 Measured Peak power 2DH5 1.48 1.04 -0.07 [dBm] 3DH5 1.83 1.33 0.24 Limit 0.125 Watt (21dBm) Remark: -- TEST RESULT: passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 22 of 33 4.7. General Limit - Radiated field strength emissions below 30 MHz 4.7.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  357 NRV-Z1  600 NRVD  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 4.7.2. Requirements FCC Part 15, Subpart C, §15.205 & §15.209 ANSI C63.10-2009 Frequency Field strength limit Distance Remarks [MHz] [μV/m] [dBμV/m] [m] 0.009 – 0.490 2400/f (kHz) 67.6 – 20Log(f) (kHz) 300 Correction factor used due to measurement distance of 3 m 0.490 – 1.705 24000/f (kHz) 87.6 – 20Log(f) (kHz) 30 Correction factor used due to measurement distance of 3 m 1.705 – 30 30 29.5 30 Correction factor used due to measurement distance of 3 m 4.7.3. Test condition and test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz RBW/VBW = 200 Hz Scan step = 80 Hz Scan data  150 kHz – 30 MHz RBW/VBW = 9 kHz Scan step = 4 kHz  other: EMI-Receiver or Scan-Mode  6 dB EMI-Receiver Mode  3dB Spectrum analyser Mode Analyzer Settings Detector Peak (pre-measurement) and Quasi-PK/Average (final if applicable) Mode: Repetitive-Scan, max-hold Sweep-Time Coupled – calibrated display if continuous signal otherwise adapted to EUT’s individual transmission duty-cycle General measurement procedures Please see chapter “Test system set-up radiated magnetic field measurements below 30 MHz” 4.7.4. Measurement Results Table of measurement results: Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark Result No. range no. no. Range No. PK AV QP 2.04 Low 0 9 kHz-30 MHz 1 1 No critical frequencies found    passed 2.05 Middle 39 9 kHz-30 MHz 1 1 No critical frequencies found    passed 2.06 High 78 9 kHz-30 MHz 1 1 No critical frequencies found    passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 23 of 33 4.7.5. Correction factors due to reduced meas. distance (f< 30 MHz) The used correction factors when the measurement distance is reduced, are taken from IEEC Transaction EMC, Vol 47, No.3, Aug. 2005, Journal Paper “EXTRAPOLATING NEAR-FIELD EMISSIONS OF LOW-FREQUENCY LOOP TRANSMITTERS”. Used Transducer factors (f < 30 MHz) 1 2 3 4 5 6 =2+3+4+5 Frequency Antenna factor Corection factor Cable loss Transducer factor 300m to 3m 30m to 3m kHz dB µV/m dB dB dB dB µV/m 9,0 20,0 -116,7 0,0 -96,7 10,6 20,0 -116,7 0,0 -96,7 12,6 20,0 -116,7 0,0 -96,7 14,8 20,0 -116,7 0,0 -96,7 17,5 20,0 -116,6 0,0 -96,6 20,7 20,0 -116,6 0,0 -96,6 24,4 20,0 -116,6 0,0 -96,6 28,9 20,0 -116,6 0,0 -96,6 34,1 20,0 -116,5 0,0 -96,5 40,3 20,0 -116,4 0,0 -96,4 47,6 20,0 -116,3 0,0 -96,3 56,2 20,0 -116,2 0,0 -96,2 66,4 20,0 -116,0 0,0 -96,0 78,4 20,0 -115,8 0,0 -95,8 92,7 20,0 -115,4 0,0 -95,4 109,4 20,0 -115,0 0,0 -95,0 129,3 20,0 -114,5 0,0 -94,5 152,7 20,0 -113,9 0,0 -93,9 180,4 20,0 -113,1 0,0 -93,1 213,1 20,0 -112,2 0,0 -92,2 251,7 20,0 -111,3 0,0 -91,3 297,3 20,0 -108,3 0,0 -88,3 351,2 20,0 -105,2 0,0 -85,2 414,8 20,0 -102,1 0,0 -82,1 490,0 20,0 -99,1 0,0 -79,1 490,0 20,0 -56,4 0,1 -36,3 582,0 20,0 -56,2 0,1 -36,1 690,0 20,0 -56,0 0,2 -35,8 820,0 20,0 -55,7 0,2 -35,5 973,0 20,0 -55,4 0,2 -35,2 1.155,0 20,0 -54,9 0,3 -34,6 1.371,0 20,0 -54,4 0,3 -34,1 1.627,0 20,0 -53,7 0,3 -33,4 1.931,0 20,0 -52,9 0,4 -32,5 2.292,0 20,0 -52,0 0,4 -31,6 2.721,0 20,0 -49,8 0,5 -29,3 3.230,0 20,0 -46,6 0,5 -26,1 3.834,0 20,0 -43,3 0,6 -22,7 4.551,0 20,0 -40,1 0,6 -19,5 5.402,0 20,0 -36,8 0,7 -16,1 6.412,0 20,0 -33,5 0,7 -12,8 7.612,0 20,0 -30,3 0,8 -9,5 9.035,0 20,0 -27,0 0,8 -6,2 10.725,0 20,0 -23,9 0,9 -3,0 12.730,0 20,0 -21,2 0,9 -0,3 15.111,0 20,0 -19,3 1,0 1,7 17.937,0 20,0 -18,4 1,0 2,6 21.292,0 20,0 -18,2 1,1 2,9 25.274,0 20,0 -18,3 1,1 2,8 30.000,0 20,0 -18,4 1,2 2,8 TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 24 of 33 4.8. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz 4.8.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 4.8.2. Requirements/Limits  Part 15 Subpart B, §15.109, class B FCC  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205  C63.4-2009 ANSI  C63.10-2009 Radiated emissions limits, 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 49.0 4.8.3. Restricted bands of operation, §15.205 MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 0.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.20725-4.20775 37.5-38.25 1645.5-1646.5 9.3-9.5 6.215-6.218 73-74.6 1660-1710 10.6-12.7 6.26775-6.26825 74.8-75.2 1718.8-1722.2 13.25-13.4 6.31175-6.31225 108-121.94 2200-2300 14.47-14.5 8.291-8.294 123-138 2310-2390 15.35-16.2 8.362-8.366 149.9-150.05 2483.5-2500 17.7-21.4 8.37625-8.38675 156.52475-156.52525 2690-2900 22.01-23.12 8.41425-8.41475 156.7-156.9 3260-3267 23.6-24.0 12.29-12.293 162.0125-167.17 3332-3339 31.2-31.8 12.51975-12.52025 167.72-173.2 3345.8-3358 36.43-36.5 12.57675-12.57725 240-285 3600-4400 Above 38.6 13.36-13.41 322-335.4 -- -- Remark: only spurious emissions are allowed within these frequency bands not exceeding the limits per §15.209 Remark: TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 25 of 33 4.8.4. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan, max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous tx-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 4.8.5. MEASUREMENT RESULTS The results are presented below in summary form only. For more information please see diagrams enclosed in annex2. Table of measurement results: Result Dia- Carrier Channel Set- OP- Used detector Frequency gram up mode Remark range no. no. no. Range No. PK AV QP 3.04 Low 0 1 1    passed 30MHz to 3.05 Middle 39 1GHz 1 1    passed 3.06 High 78 1 1    passed Remark: TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 26 of 33 4.9. General Limit - Radiated emissions, above 1 GHz 4.9.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2    antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DCpower  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  611 E3632A line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 4.9.2. Requirements/Limits  Part 15 Subpart B, §15.109 class B FCC  Part 15 subpart C, §15.209 @ frequencies defined in §15.205 ANSI  C63.4-2009  C63.10-2009 Limits, 3 meters Frequency AV AV Peak Peak [MHz] [µV/m] [dBµV/m] [µV/m] [dBµV/m] above 1 GHz 500 54.0 5000 74.0 4.9.3. Test condition and measurement test set-up Signal ink to test system (if used):  air link  cable connection EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW 1 MHz / 3 MHz Mode: Repetitive-Scan, max-hold Scan step 400 kHz Sweep-Time Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” 4.9.4. Measurement Results The results are presented below in summary form only. For more information please see diagrams in annex 2. Dia- Carrier Channel Set- OP- Used detector Result Frequency gram up mode Remark range no. no. no. Range No. PK AV QP 4.04 Low 0 1 to 18GHz 1 1 --    passed 18 to 25 4.07 Low 0 1 1 --    passed GHz 4.05 Middle 39 1 to 18GHz 1 1 --    passed 18 to 25 4.08 Middle 39 1 1 --    passed GHz 4.06 High 78 1 to 18GHz 1 1 --    passed 18 to 25 4.09 High 78 1 1 --    passed GHz Remark: TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 27 of 33 4.10. RF-Parameter - Radiated Band Edge compliance measurements 4.10.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2    antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DC power  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  611 E3632A line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 4.10.2. Requirements/Limits  Part 15 Subpart B, §15.109 class B FCC  Part 15 subpart C, §15.209 @ frequencies defined in §15.205 ANSI  C63.4-2009  C63.10-2009 4.10.3. Measurement Method For uncritical results where a measurement bandwidth of 1MHz can clearly show the compliance without influencing the results, a field strength measurement was performed only to show compliance. For critical results a Marker-Delta marker method was used for showing compliance to restricted bands according §15.205. The method is according ANSI 63.10:2009 “Marker-Delta method”. The method consists of three independent steps: 1. Step: Prior to the measurement the fundamental radiated In-Band field strength was performed. The determined value is used as reference value. 2. Step: Second step consist of finding the relative attenuation between the fundamental emission and the maximum local out-of-band emission (within 2 MHz range around the band edge either on the band-edge directly or some modulation product if the level is greater than that on the band-edge) when measured with lower resolution bandwidth. 3. Step: The delta value recorded in step 2 will be subtracted from value recorded in step 1, thus giving the required field strength at the band-edge. This value must fulfil the requirements for radiated spurious emissions in restricted bands in §15.205 (RSS-Gen) with the general limits of §15.209 or RSS-Gen.. 4.10.4. EUT settings A fully loaded battery was used and changed if required in order to keep the voltage constant over the test time. The EUT was instructed to send with maximum power (if adjustable) according to applicants instructions. 4.10.5. Measurements results: for non-restricted bands near-by (§15.247) Remark: TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 28 of 33 4.10.6. Measurements results: for restricted bands near-by (§15.205) Remark: 4.10.7. Verdict: passed TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 29 of 33 4.11. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it contribution to the overall uncertainty according it’s statistical distribution calculated. Calculated uncertainty based RF-Measurement Reference Frequency range Remarks on a confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Power Output radiated - 30 MHz - 4 GHz 3.17 dB Substitution Power Output conducted - 9 kHz - 20 GHz 1.0 dB - Conducted emissions - 9 kHz - 20 GHz 1.0 dB - on antenna ports 20 GHz - 40 GHz 0.1272 ppm (Delta Marker) Frequency error Occupied bandwidth - 9 kHz - 4 GHz 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency error Emission bandwidth 9 kHz - 4 GHz - 1.0 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic field Radiated emissions 30 MHz - 1 GHz 4.2 dB E-field - Enclosure 1 GHz - 20 GHz 3.17 dB Substitution (Power) Table: measurement uncertainties, valid for conducted/radiated measurements 5. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) FCC, Federal Communications MRA US-EU 558 Radiated Measurements above 1 GHz, 3 m (FAR) Commission 0003 348 Mains Ports Conducted Interference Measurements Laboratory Division, USA 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R-2666 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G-301 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C-2914 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 30 of 33 6. Instruments and Ancillary 6.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 6.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 264 Spectrum Analyzer FSEK 30 826939/005 Bios=2.1, Analyzer= 3.20 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 TSI 1.53 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 31 of 33 6.1.2. Single instruments and test systems Ref.-No. calibration Remark Interval of Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 30.04.2016 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 30.04.2016 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 30.04.2016 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 30.04.2017 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 31.03.2016 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO 36/12 M - 31.03.2017 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.04.2018 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 30.04.2018 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 30.04.2017 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1g 31.07.2015 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 Helmholtz coil: 2x10 coils 090 Helmholtz coil: 2x10 coils in series - RWTÜV 24 M 4 31.03.2016 in 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.04.2018 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.04.2018 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 31.03.2016 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 36 M - 30.04.2018 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 31.03.2016 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 31.03.2016 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 31.03.2016 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 31.03.2016 264 Spectrum Analyzer FSEK 30 826939/005 Rohde & Schwarz 12 M - 30.04.2016 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 31.03.2016 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 31.03.2016 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 287 pre-amplifier 25MHz - 4GHz AMF-2D-100M4G-35-10P 379418 Miteq 12 M 1c 31.07.2015 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 31.07.2015 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 30.04.2016 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 31.03.2017 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 31.03.2017 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 Heraeus Vötsch 24 M - 30.11.2014 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 31.03.2016 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 30.04.2017 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 31.03.2016 356 power sensor NRV-Z1 882322/014 Rohde & Schwarz 24 M - 31.03.2015 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 30.04.2017 371 Bluetooth Tester CBT32 100153 R&S 24 M - 31.03.2016 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 24 M - 30.04.2017 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 30.04.2016 389 Digital Multimeter Keithley 2000 0583926 Keithley 24 M - 30.04.2017 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 30.04.2016 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 30.04.2016 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 31.03.2017 System EMI field (SAR) 441 CTC-SAR-EMI Cable Loss - CETECOM 12 M 5 30.01.2016 Cable 443 CTC-FAR-EMI-RSE System CTC-FAR-EMI- - ETS-Lindgren / 12 M 5 31.07.2015 TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 32 of 33 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due RSE CETECOM WRCT 1850.0/2170.0- Wainwright Instruments 448 notch filter WCDMA_FDD II 5 12 M 1c 31.07.2015 5/40- GmbH WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 31.07.2015 8SSK 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.04.2016 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 31.03.2016 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.04.2018 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2018 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 30.04.2017 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 31.07.2015 10P System EMI field (SAR) ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI - 24 M - 30.06.2015 NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 30.04.2016 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 31.07.2015 6EEK 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 30.04.2017 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.04.2016 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 30.04.2016 548 Digital-Barometer GBP 2300 without Greisinger GmbH 36 M - 30.06.2015 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.03.2015 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 31.07.2015 557 System CTC-OTA-2 R&S TS8991 - Rohde & Schwarz 12 M 5 30.09.2015 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 31.07.2015 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 31.03.2016 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 594 Wideband Radio Communication Tester CMW 500 101757 Rohde & Schwarz 12 M - 30.04.2016 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz 36 M - 31.03.2016 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Rohde & Schwarz 24 M - 30.04.2017 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 30.04.2017 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 30.04.2017 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 31.03.2016 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 01.12.2015 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4.1.4 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.04.2017 3 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 636 Thermal Imaging camera Ti32 Ti32-12060213 Fluke Corporation 36 M - 31.07.2015 HDMI cable with Ethernet 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 1m 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 642 Wideband Radio Communication Tester CMW 500 126089 Rohde&Schwarz 12 M - 30.04.2016 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 31.03.2016 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.04.2016 Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 30.04.2017 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.04.2016 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - TR6-0461-14-3-1e-C1

Test Report 6-0461-14-3-1e-C1, Page 33 of 33 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 24 M - 31.03.2016 693 TS8997 CTC-Radio Lab 1_TS8997 - Rohde&Schwarz 12 M 5 01.05.2015 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 6.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 7. Versions of test reports (change history) Version Applied changes Date of release 1.0 Initial release 2015-05-20 1.1 corrections in chapter 4.5 2015-07-14 -- -- -- TR6-0461-14-3-1e-C1


Document Created: 2019-09-23 17:53:24
Document Modified: 2019-09-23 17:53:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC