RF Exposure Evaluation

FCC ID: YBN-AIVISBX0

RF Exposure Info

Download: PDF
FCCID_4248610

TEST REPORT No.: 18-1-0221601T06a-C1 According to: FCC Regulations Part 1.1310 Part 2.1091 IC-Regulations RSS-102, Issue 5 for Robert Bosch Car Multimedia GmbH AIVISBX0 Navigationsystem with WLAN and Bluetooth FCC: YBN-AIVISBX0 ISED: 9595A-AIVISBX0 Laboratory Accreditation and Listings Voluntary Controls for Electromagnetic Industry Canada Emissions Reg. No.: MRA US-EU 0003 Reg. No.: 3462D-2 R-2666 C-2914, Reg. No.: 3462D-3 T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 18-1-0221601T06a-C1, Page 2 of 17 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. Summary of tests results .................................................................................................................................. 3 1.2. Attestation:....................................................................................................................................................... 3 2. ADMINISTRATIVE DATA ............................................................................................................................... 4 2.1. Identification of the testing laboratory ............................................................................................................. 4 2.2. Test location .................................................................................................................................................... 4 2.3. Organizational items ........................................................................................................................................ 4 2.4. Applicant’s details ........................................................................................................................................... 4 2.5. Manufacturer’s details ..................................................................................................................................... 4 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 5 3.1. Summary of product description ...................................................................................................................... 5 3.2. EUT Technologies ........................................................................................................................................... 5 3.3. Antenna Information ........................................................................................................................................ 5 3.4. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 6 3.5. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 6 3.6. EUT set-ups ..................................................................................................................................................... 6 3.7. EUT operating modes ...................................................................................................................................... 6 4. MEASUREMENTS ............................................................................................................................................. 7 4.1. Radio Frequency Exposure Evaluation §2.1091 .............................................................................................. 7 4.1.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') ................ 7 4.2. Requirements and limits for RSS Standard ..................................................................................................... 9 4.3. MPE Calculation method ................................................................................................................................. 9 4.4. Evaluation Method........................................................................................................................................... 10 4.5. Results for fixed and mobile ............................................................................................................................ 10 4.6. Conclusion ....................................................................................................................................................... 16 4.7. Measurement uncertainties .............................................................................................................................. 16 5. ABBREVIATIONS USED IN THIS REPORT ................................................................................................. 17 6. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 17 7. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................. 17 Table of annex Total pages Annex 1: Separate document applicant’s document “Tune_up_info_AIVISBX0.pdf” 02 Annex 2: Separate document applicant’s document “CETECOM-TR18-1-0048201T07a.pdf” 36 Annex 3: External photographs of EUT (separate document) CETECOM- TR18-1-0048201T02a-A2 08 The listed attachments are an integral part of this report. CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 3 of 17 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The presented Equipment Under Test (in this report, hereinafter referred as EUT) integrates a BT 2.4 GHz RF Transceiver. Other implemented wireless technologies were not considered within this test report. Following tests have been performed to show compliance with applicable FCC Part 2.1091 and FCC Part 1.1310 of the FCC CFR 47 Rules. 1.1. Summary of tests results RF-Exposure Evaluation (separation distance user to RF-radiating element greater 20cm) References & Limits EUT EUT Test cases Port FCC Test Limit RSS Test Limit op. Result set-up Standard Standard mode RF-Field Strength Radio Limits: frequency §1.1310 RSS- FCC: Chapter 4 radiation Cabinet §2.1091 102, 1 2 Pass “general Table 4 exposure §2.1093 Issue 5 population/ Requirements uncontrolled” environment Remark: Calculations based on Datasheet delivered by applicant 1.2. Attestation: I declare that all measurements were performed by me or under my supervision and that all measurements have been performed and are correct to my best knowledge and belief to Industry Canada standards. All requirements as shown in above table are met in accordance with enumerated standards. The current version of the Test Report CETECOM_TR18-1-0221601T06a-C1 replaces the Test Report CETECOM_TR18-1-0221601T06a dated 2018-12-10. The replaced test report is herewith invalid. Digital unterschrieben von B.Sc. Mohamed Ahmed DN: cn=B.Sc. Mohamed Ahmed, o=Cetecom GmbH, ou=RC/EMC, email=mohamed.ahmed@cetec om.com, c=DE Datum: 2018.12.17 15:41:08 +01'00' ...................................................... ......................................................... Dipl.-Ing. Niels Jeß B.Sc. Mohamed Ahmed Responsible for test section Responsible for test report CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 4 of 17 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report: B.Sc. Mohamed Ahmed Responsible for Project: Dipl. Ing. Ninovic Perez Receipt of EUT: -- Date(s) of test: -- Date of report: 2018-12-17 2.4. Applicant’s details Applicant’s name: Robert Bosch Car Multimedia GmbH Address: Robert-Bosch-Straße 200 31139 Hildesheim Germany Contact person: Mr. Salvatore Miraglia 2.5. Manufacturer’s details Manufacturer’s name: please see applicant's details Address: please see applicant's details CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 5 of 17 3. Equipment under test (EUT) 3.1. Summary of product description FCC ID: YBN-AIVISBX0 Product name AIVISBX0 General population/uncontrolled environment Exposure category Occupational exposure/controlled environment Conducted ERP Output power EIRP Peak Source-based time-averaging Antenna gain details refer Annex 2 2T2R MIMO 3T3R 4T4R Technology 1T1R non-MIMO 1T2R 2T1R Standalone Evaluation type Simultaneous transmission 20 cm Evaluation distance XXX cm declares by manufacturer Production Unit EUT type Pre-Production Unit Engineering Unit Mobile device Device type Fixed device CFR 47 FCC Part 2.1091 CFR 47 FCC Part 1.1310 Refer rules KDB 447497 D01v06 October 23, 2015 KDB 865664 D01v01r02 October 23, 2015 3.2. EUT Technologies Wireless Frequency bands Operation mode Technologies 2.4GHz 802.11 b/g/n WLAN 5GHz 802.11 a/n/ac Bluetooth LE Bluetooth 2.4GHz Bluetooth EDR 3.3. Antenna Information Wireless Frequency bands Antenna type Maximum antenna gain Technologies 2.4GHz PIFA WLAN Antenna 0 refer to Annex 2 5GHz PCB PIFA Bluetooth 2.4GHz Antenna 1 refer to Annex 2 PCB CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 6 of 17 3.4. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) Navigationsystem EUT A AIVISBX0 with WLAN and 0005091 C-Sample 1003 Bluetooth *) EUT short description is used to simplify the identification of the EUT in this test report. 3.5. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE short S/N HW SW descrip- Auxiliary Equipment Type serial number hardware status software status tion *) AE 1 -- -- -- -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.6. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) set. 1 EUT A -- *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. 3.7. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) op. 1 WLAN Only theoretically calculation op. 2 Bluetooth Only theoretically calculation *) EUT operating mode no. is used to simplify the test report. CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 7 of 17 4. Measurements 4.1. Radio Frequency Exposure Evaluation §2.1091 4.1.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 For Evaluation instruments are not needed. Results are determined by calculation based on applicants delivered Tune-Up procedure. 4.1.2. Requirements The criteria used for the evaluation of human exposure to radio frequency radiation is table 1 according FCC §1.1310 and table chapter 4.2 of RSS-102 standard and it is subject for evaluation of the RF exposure prior to FCC: §1.1310 equipment authorization. As the mobile equipment is authorized under Part 22 (Subpart H) and Part 24 of the FCC Rules, it is subject for evaluation of the RF exposure prior to equipment authorization. Further information on evaluating compliance with these limits can be found in the FCC’s OST/OET Bulletin Number 65, ‘‘Evaluating Compliance with FCC-Specified Guidelines for Human Exposure to Radiofrequency Radiation.’’ For purposes of these requirements mobile devices are defined by the FCC as transmitters designed to be used FCC § 2.1091 in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between radiating structures and the body of the user or nearby persons. These devices are normally evaluated for exposure potential with relation to the MPE limits given in Table 1 of Appendix A. 4.1.2.1. Valid for FCC Table 1: LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency range Electric field strength Magnetic field strength Power density Averaging time [MHz) [V/m] [A/m] [mW/cm²] [minutes] 30 - 300 61.4 0.163 1.0 6 300 - 1500 - f/300 6 1500 - 100,000 - 5 6 (B) Limits for General Population / Uncontrolled Exposure 0.3 – 1.34 614 1.63 *(100) 30 1.34 – 30 824/f 2.19/f *(180/f²) 30 30 - 300 27.5 0.073 0.2 30 300 - 1500 - - f/1500 30 1500 – 100,0 - - 1.0 30 f=frequency in MHz *Plane-wave equivalent power density NOTE1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. These limits apply to amateur station licensees and members of their immediate household as discussed in the text. NOTE2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. As discussed in the text, these limits apply to neighbours living near amateur radio stations. CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 8 of 17 4.1.3 General Limits: Cellular Radiotelephone Service (subpart H of part 22) FCC: §1.1307 Non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 1000 W ERP (1640 W EIRP) Personal Communications Services (part 24) FCC §1.1307 Broadband PCS (subpart E): non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 2000 W ERP (3280 W EIRP) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Table 1(B) Limits for General Population/Uncontrolled Exposure FCC §1.1310 300–1500 MHz: f/1500 mW/cm² 1500–100,000 MHz: 1.0 mW/cm² Subject to routine evaluation is required when the device operate at frequencies of 1.5 GHz or below and their FCC §2.1091 effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. (a) Base stations are limited to 1640 watts peak equivalent isotropically radiated power (e.i.r.p.) with an antenna FCC §24.232 height up to 300 meters HAAT. b) Mobile/portable stations are limited to 2 watts e.i.r.p. peak power, … (a) Maximum ERP. The effective radiated power (ERP) of base transmitters and cellular repeaters must not exceed FCC §22.913 500 Watts. The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts. FCC §27.50 (10) Portable stations (hand-held devices) are limited to 3 watts ERP; and (C )(10) (4) Fixed, mobile, and portable (hand-held) stations operating in the 1710-1755 MHz band are limited to 1 watt FCC §27.50(d) EIRP. KDBs No. 447498 D01 v06 CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 9 of 17 4.2. Requirements and limits for RSS Standard 2.5 Exemption Limits for Routine Evaluation All transmitters are exempt from routine SAR and RF exposure evaluations provided that they comply with the requirements of sections 2.5.1 or 2.5.2. If the equipment under test (EUT) meets the requirements of sections 2.5.1 or 2.5.2, applicants are only required to submit a properly signed declaration of compliance (see Annex C). The information contained in the RF exposure technical brief may be limited to the value(s) of the maximum output power, the information that demonstrates how the maximum output power of the transmitter was derived and the rationale for the separation distances applied (see Table 1), which must be based on the most conservative exposure condition for the applicable module or host platform test procedure requirements. 2.5.2 Exemption Limits for Routine Evaluation — RF Exposure Evaluation RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows:  below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance);  at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz;  at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); RSS-102, Issue 5  at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz;  at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). In these cases, the information contained in the RF exposure technical brief may be limited to information that demonstrates how the e.i.r.p. was derived. 2.6 User Manual Requirements The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions (e.g. proper accessory required, including the proper orientation of the device in the accessory, maximum antenna gain in the case of detachable antenna), in order to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual. The user manual of devices intended for controlled use shall also include information relating to the operating characteristics of the device; the operating instructions to ensure compliance with SAR and/or RF field strength limits; information on the installation and operation of accessories to ensure compliance with SAR and/or RF field strength limits; and contact information where the user can obtain Canadian information on RF exposure and compliance. Other related information may also be included. 4.3. MPE Calculation method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 EIRP P  G S  4R 2 4R 2 S  4R 2 GNUMERIC  P Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the centre of radiation of the antenna CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 10 of 17 4.4. Evaluation Method 4.4.1. Standalone Valid for WLAN & BT Mode: • The peak power was checked on 3 frequencies (lowest/middle/highest) within the BT band and the results compared to applicant’s declared power values (datasheet). • No duty-cycle correction factor is applicable Please find in the following tables the calculations based on applicants datasheet for the power values and antenna gain. 4.5. Results for fixed and mobile 4.5.1. Results for FCC Standard 4.5.1.1. MPE results for 2.4GHz Operation Mode Frequency Declared Max. positive Measured Calculated Duty cycle Calculated Calculated EIRP MPE Lim it MPE-Value Margin to Fraction for Max. on channel m axim um tolerance Antenna Gain m axim um EIRP m axim um incl. Duty cycle accord. Lim it: conducted according (Output pow er EIRP ((Output pow er + Table 1 Co-Location Fraction- output m anfacturer's + (Output Tune-up)) x calculations Value pow er tune-up info Tune-up) pow er + Duty cycle) within Tune-up) (dB) Frequency- (MHz) (dBm ) (m W) Band (dBm ) (dBi) % (W) (m W/cm ^2) (m W/cm ^2) (m W/cm ^2) 2402,0 -2,5 0,0 0,4 -2,1 0,0006 0,6 1,0000 0,0001 0,9999 0,000122 Bluetooth 0,9999 2440,0 -2,5 0,0 0,4 -2,1 100% 0,0006 0,6 1,0000 0,0001 0,000122 0,0001221 2.4GHZ 2480,0 -2,5 0,0 0,4 -2,1 0,0006 0,6 1,0000 0,0001 0,9999 0,000122 2412,0 12,6 0,0 1,5 14,1 0,0257 25,7 1,0000 0,0051 0,9949 0,005114 WLAN 2.4GHZ 2440,0 12,6 0,0 1,5 14,1 100% 0,0257 25,7 1,0000 0,0051 0,9949 0,005114 0,0051136 2462,0 12,6 0,0 1,5 14,1 0,0257 25,7 1,0000 0,0051 0,9949 0,005114 Maxim um calculated MPE value: Low est MPE- 1,0000 [m W/cm ^2] Lim it: Highest MPE 0,0051 [m W/cm ^2] value: Low est Margin 0,9949 [m W/cm ^2] to lim it: CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 11 of 17 4.5.1.2. MPE results for 5GHz Operation Frequency on Declared Max. positive Measured Calculated Duty cycle Calculated Calculated MPE-Value MPE-Value Margin Mode channel maximum tolerance Antenna Gain maximum maximum EIRP incl. Duty Maximum conducted according EIRP EIRP cycle Fraction output power manufacturer' (Output power (Output power ((Output Fraction for Value s tune-up info + + power + Co-location Tune-up) Tune-up) Tune-up)) x within calculations Duty cycle) Frequency (dB) (MHz) (dBm) (dBi) (dBm) (%) (W) (mW) (mW/cm^2) (mW/cm^2) (mW/cm^2) band 5180,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 W-LAN 5GHz 5200,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 0,0044 (20MHZ BW) 5240,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 5260,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 W-LAN 5GHz 5280,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 0,0044 (20MHZ BW) 5320,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 5500,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 W-LAN 5GHz 5580,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 0,0044 (20MHZ BW) 5700,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 5745,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 W-LAN 5GHz 5785,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 0,0044 (20MHZ BW) 5825,0 100% 0,022 22,28 1,0000 0,00443 0,9956 0,0044 W-LAN 5GHz 5190,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 0,0043 (40MHz BW) 5230,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 W-LAN 5GHz 5270,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 0,0043 (40MHz BW) 5310,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 5510,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 W-LAN 5GHz 5550,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 0,0043 (40MHz BW) 5670,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 W-LAN 5GHz 5755,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 0,0043 (40MHz BW) 5795,0 100% 0,021 21,38 1,0000 0,00425 0,9957 0,0043 5210,0 100% 0,008 7,59 1,0000 0,00151 0,9985 0,0015 W-LAN 5GHz 5290,0 100% 0,008 7,59 1,0000 0,00151 0,9985 0,0015 0,0015 (80MHz BW) 5530,0 100% 0,008 7,59 1,0000 0,00151 0,9985 0,0015 5775,0 100% 0,008 7,59 1,0000 0,00151 0,9985 0,0015 Maximum calculated MPE value: 5GHz Low est MPE- 1,0000 [W/m ^2] Lim it: Highest MPE- 0,0043 [W/m ^2] value: Margin to 0,9957 [W/m ^2] lim it 4.5.1.3. MPE results for co-location CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 12 of 17 W-LAN Bluetooth W-LAN 2.4GHz 2.4GHz 5GHz Ratio of MPE- 0,00511364 0,000122104 0,00425334 Value/Limit W-LAN 0,00511364 -- 0,005235744 0,00936698 2.4GHz Bluetooth 0,000122104 0,005235744 -- 0,004375445 2.4GHz W-LAN 0,00425334 0,00936698 0,004375445 -- 5GHz Maximum-Value 0,00936698 1. Output power including tune-up tolerance; 2. Output power was adjust to duty cycle at 100% if measured duty cycle less than 98%; 3. MPE evaluate distance is 20cm from user manual provide by manufacturer; 4. Depending on output power and antenna gain only the worst case is reported; CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 13 of 17 4.5.2. Results for RSS Standard 4.5.2.1. MPE Results for 2.4GHz Operation Mode Frequency Declared Max. positive Measured Calculated Duty-Cycle Maxim um Calculated EIRP incl. MPE Lim it MPE-Value Margin on channel m axim um tolerance Antenna m axim um EIRP EIRP Duty cycle accord. Table 4 conducted according Gain (Output pow er + ((Output pow er + Maximum output m anfacturer's Tune-up) Tune-up)) x Fraction Fraction for pow er tune-up info Duty cycle) Value Co-location within (W/m ^2) calculations (MHz) (dBm ) (dB) (dBi) (dBm ) % (W) (W) (W/m ^2) (W/m ^2) Frequency band 2402,0 -2,5 0,0 0,4 100% 0,0006 0,0006 5,35080 0,0012 5,3496 0,000228 Bluetooth 2.4GHZ 2442,0 -2,5 0,0 0,4 100% 0,0006 0,0006 5,41154 0,0012 5,4103 0,000226 0,00023 2480,0 -2,5 0,0 0,4 100% 0,0006 0,0006 5,46895 0,0012 5,4677 0,000223 2402,0 12,6 0,0 1,5 100% 0,0257 0,0257 5,35080 0,0511 5,2997 0,009557 WLAN 2.4GHZ 2442,0 12,6 0,0 1,5 100% 0,0257 0,0257 5,41154 0,0511 5,3604 0,009450 0,00956 2462,0 12,6 0,0 1,5 100% 0,0257 0,0257 5,44179 0,0511 5,3907 0,009397 Maximum calculated MPE value: Low est MPE- 5,3508 [W/m ^2] Lim it: Highest MPE 0,0012 [W/m ^2] value: Low est m argin 5,3496 [W/m ^2] to lim it CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 14 of 17 4.5.2.2. MPE Results for 5GHz Operation Frequency on Measured Measured EIRP Duty cycle Maximum Equivalent MPE Limit MPE-Value Margin Maximum Mode channel maximum Antenna Gain EIRP EIRP accord. Table conducted (EIRP x duty 4 Fraction Fraction for output power cycle) Value Co-location within calculations Frequency (MHz) (dBm) (dBi) (dBm) (% ) (W) (mW) (W/m^2) (W/m^2) (W/m^2) band 5180,0 100% 0,022 22,28 9,0471 0,0443 9,0027 0,0049 W-LAN 5GHz 5200,0 100% 0,022 22,28 9,0709 0,0443 9,0266 0,0049 0,0049 (20MHZ BW) 5240,0 100% 0,022 22,28 9,1186 0,0443 9,0742 0,0049 5260,0 100% 0,022 22,28 9,1423 0,0443 9,0980 0,0048 W-LAN 5GHz 5280,0 100% 0,022 22,28 9,1661 0,0443 9,1217 0,0048 0,0048 (20MHZ BW) 5320,0 100% 0,022 22,28 9,2135 0,0443 9,1691 0,0048 5500,0 100% 0,022 22,28 9,4254 0,0443 9,3811 0,0047 W-LAN 5GHz 5580,0 100% 0,022 22,28 9,5189 0,0443 9,4745 0,0047 0,0047 (20MHZ BW) 5700,0 100% 0,022 22,28 9,6583 0,0443 9,6140 0,0046 5745,0 100% 0,022 22,28 9,7103 0,0443 9,6660 0,0046 W-LAN 5GHz 5785,0 100% 0,022 22,28 9,7565 0,0443 9,7122 0,0045 0,0046 (20MHZ BW) 5825,0 100% 0,022 22,28 9,8025 0,0443 9,7582 0,0045 W-LAN 5GHz 5190,0 100% 0,021 21,38 9,0590 0,0425 9,0165 0,0047 0,0047 (40MHz BW) 5230,0 100% 0,021 21,38 9,1067 0,0425 9,0641 0,0047 W-LAN 5GHz 5270,0 100% 0,021 21,38 9,1542 0,0425 9,1117 0,0046 0,0046 (40MHz BW) 5310,0 100% 0,021 21,38 9,2016 0,0425 9,1591 0,0046 5510,0 100% 0,021 21,38 9,4371 0,0425 9,3946 0,0045 W-LAN 5GHz 5550,0 100% 0,021 21,38 9,4839 0,0425 9,4413 0,0045 0,0045 (40MHz BW) 5670,0 100% 0,021 21,38 9,6235 0,0425 9,5810 0,0044 W-LAN 5GHz 5755,0 100% 0,021 21,38 9,7219 0,0425 9,6794 0,0044 0,0044 (40MHz BW) 5795,0 100% 0,021 21,38 9,7680 0,0425 9,7255 0,0044 5210,0 100% 0,008 7,59 9,0829 0,0151 9,0678 0,0017 W-LAN 5GHz 5290,0 100% 0,008 7,59 9,1779 0,0151 9,1628 0,0016 0,0017 (80MHz BW) 5530,0 100% 0,008 7,59 9,4605 0,0151 9,4454 0,0016 5775,0 100% 0,008 7,59 9,7450 0,0151 9,7299 0,0015 Maximum calculated MPE value: 5GHz Low est MPE- 9,0471 [W/m ^2] Lim it: Highest MPE- 0,0425 [W/m ^2] value: Margin to 9,0045 [W/m ^2] lim it CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 15 of 17 4.5.2.3. MPE results for co-location W-LAN W-LAN W-LAN 2.4GHz 2.4GHz 5GHz Ratio of MPE- 0,009556768 0,000228198 0,00470134 Value/Limit W-LAN 0,009556768 0,01911354 0,00978497 0,014258109 2.4GHz Bluetooth 0,000228198 0,0002282 0,0002282 0,000228198 2.4GHz W-LAN 0,00470134 0,01425811 0,00492954 0,009402681 5GHz Maximum- 0,0191135 Value 1. Output power including tune-up tolerance; 2. Output power was adjust to duty cycle at 100% if measured duty cycle less than 98%; 3. MPE evaluate distance is 20cm from user manual provide by manufacturer; 4. Depending on output power and antenna gain only the worst case is reported; CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 16 of 17 4.6. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. The measurement results comply with the RSS-102, Issue 5. 4.7. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based on a RF-Measurement Reference Frequency range Remarks confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Substitution Power Output radiated - 30 MHz - 4 GHz 3.17 dB method Cel- Cel- Set-up No. BT1 W1 W2 C1 C2 Power Output conducted - 9 kHz - 12.75 GHz N/A 0.60 -- -- -- - 12.75 - 26.5GHz N/A 0.82 -- -- -- Conducted emissions - 9 kHz - 2.8 GHz 0.70 N/A -- -- -- N/A - not on RF-port 2.8 GHz - 12.75GHz 1.48 N/A -- -- -- applicable 12.75 GHz - 18GHz 1.81 N/A -- -- -- 18 GHz - 26.5GHz 1.83 N/A -- -- -- 0.1272 ppm (Delta Marker) Frequency Occupied bandwidth - 9 kHz - 4 GHz error 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency Emission bandwidth 9 kHz - 4 GHz error - See above: 0.70 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic Radiated emissions 30 MHz - 1 GHz 4.2 dB field - Enclosure 1 GHz - 20 GHz 3.17 dB E-field Substitution Table: measurement uncertainties, valid for conducted/radiated measurements CETECOM_TR18_1_0221601T06a-C1

Test Report 18-1-0221601T06a-C1, Page 17 of 17 5. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV , AVG, CAV Average detector EIRP Equivalent isotropically radiated power, determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission, USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification, Dokuments from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power 6. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) FCC, Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) MRA US-EU Commission 558 Radiated Measurements above 1 GHz, 3 m (FAR) 0003 Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R-2666 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G-301 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C-2914 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room 7. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2018-12-10 C1 80MHz bandwidth added, Measured Power adjusted for each BW 2018-12-17 END OF TEST REPORT CETECOM_TR18_1_0221601T06a-C1


Document Created: 2018-12-17 16:03:38
Document Modified: 2018-12-17 16:03:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC