RF Exposure Evaluation

FCC ID: YBN-AIVIP42M0

RF Exposure Info

Download: PDF
FCCID_4036739

TEST REPORT No.: 18-1-0086501T05a According to: FCC Regulations Part 1.1310 Part 2.1091 IC-Regulations RSS-102, Issue 5 for Robert Bosch Car Multimedia GmbH AIVIP42M0 FCC-ID: YBN-AIVIP42M0 IC: 9595A-AIVIP42M0 Laboratory Accreditation and Listings Voluntary Controls for Industry Canada Electromagnetic Emissions Reg. No.: MRA US-EU 0003 Reg. No.: 3462D-2 R-2666 C-2914, Reg. No.: 3462D-3 T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 17 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 18-1-0086501T05a, Page 2 of 17 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. Summary of tests results .................................................................................................................................. 3 2. ADMINISTRATIVE DATA ............................................................................................................................... 4 2.1. Identification of the testing laboratory ............................................................................................................. 4 2.2. Test location .................................................................................................................................................... 4 2.3. Organizational items ........................................................................................................................................ 4 2.4. Applicant’s details ........................................................................................................................................... 4 2.5. Manufacturer’s details ..................................................................................................................................... 4 1.2 Summary of product description ....................................................................................................................... 5 1.3 Refer Rules ....................................................................................................................................................... 5 1.4 EUT Technologies ............................................................................................................................................ 5 1.5 Antenna Information ......................................................................................................................................... 7 2.6. EUT, Auxiliary Equipment (AE) and EUT set-ups ......................................................................................... 11 2.7. EUT operating modes ...................................................................................................................................... 11 2.8. Test mode software .......................................................................................................................................... 11 3. MEASUREMENTS ............................................................................................................................................. 12 3.1. Radio Frequency Exposure Evaluation §2.1091 .............................................................................................. 12 3.1.Test location ..................................................................................................................................................... 12 3.2 Evaluation Rules for FCC Standard .................................................................................................................. 12 3.3 Limits for FCC Standard .................................................................................................................................. 12 3.4 Requirements and limits for RSS Standard ...................................................................................................... 13 3.5 MPE Calculation method .................................................................................................................................. 13 3.7 Evaluation Method............................................................................................................................................ 14 3.8 Conclusion ........................................................................................................................................................ 16 4. MEASUREMENT UNCERTAINTIES, INSTRUMENTS AND ANCILLARY ............................................ 17 5. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................. 17 CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 3 of 17 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The presented Equipment Under Test (in this report, hereinafter referred as EUT) integrates a BT BDR/EDR 2.4 GHz RF Transceiver (Hopping Mode), WLAN 2.4 GHz RF Transceiver and WLAN 5GHz RF Transceiver. Other implemented wireless technologies were not considered within this test report. Following tests have been performed to show compliance with applicable FCC Part 2.1091 and FCC Part 1.1310 of the FCC CFR 47 Rules. 1.1. Summary of tests results RF-Exposure Evaluation (separation distance user to RF-radiating element greater 20cm) References & Limits EUT EUT Test cases Port FCC Test Limit RSS Test Limit op. Result set-up Standard Standard mode RF-Field Cabinet Strength Radio + Limits: frequency RSS- Inter- §2.1091 FCC: Chapter 4 radiation 102, 1,2 1,2,3 Pass Connecting §2.1093 “general Table4 exposure Issue 5 Cables population/ Requirements (conducted) uncontrolled” environment Remark: 1.) See separate test reports & corresponding annexes for following installed technologies FCC WLAN 2.4GHz: BTL-FCCP-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 FCC BT BDR/EDR: BTL-FCCP-1-1808C227_BT_ AIVIP42M0 MDG1810008 FCC WLAN 5GHz BTL-FCCP-3-1808C227_5G_ AIVIP42M0 MDG1810008 ISED WLAN 2.4GHz: BTL-ISEDR-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 ISED BT BDR/EDR: BTL-ISEDR-1-1808C227_BT_ AIVIP42M0 MDG1810008 ISED WLAN 5GHz BTL-ISEDR-3-1808C227_5G_ AIVIP42M0 MDG1810008 2.) Calculations based on Tune-Up Info delivered by applicant Digital unterschrieben Ninovic von Niels Jeß DN: cn=Niels Jeß, o=CETECOM GmbH, Perez ou=Branch Duesseldorf, 2018.10. 16 10:26: email=niels.jess@cet ecom.com, c=DE Datum: 2018.10.16 11:38:16 +02'00' 22 +01'00' ...................................................... .................................................... Dipl.-Ing. Niels Jeß Dipl.-Ing. Ninovic Perez Responsible for test section Responsible for test report CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 4 of 17 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report: Dipl.-Ing Ninovic Perez Responsible for project: Dipl.-Ing. Ninovic Perez Receipt of EUT: 2018-08-29 Date(s) of test: 2018-09-03 – 2018-09-12 Date of report: 2018-10-12 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: Robert Bosch Car Multimedia GmbH Address: Robert-Bosch-Straße 200 31137 Hildesheim Germany Contact person: Mr. Salvatore Miraglia 2.5. Manufacturer’s details Manufacturer’s name: please see applicant's details Address: please see applicant's details CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 5 of 17 1.2 Summary of product description FCC ID: YBN-AIVIP42M0 ISED: 9595A-AIVIP42M0 Product name AIVIP42M0 General population/uncontrolled environment Exposure category Occupational exposure/controlled environment Conducted ERP Output power EIRP Peak Source-based time-averaging Antenna gain details refer Chapter 1.5 2T2R MIMO 3T3R 4T4R Technology 1T1R non-MIMO 1T2R 2T1R Standalone Evaluation type Simultaneous transmission 20 cm Evaluation distance XXX cm declares by manufacturer Production Unit EUT type Engineering Unit Mobile device Device type Fixed device CFR 47 FCC Part 2.1091 CFR 47 FCC Part 1.1310 Refer rules KDB 447497 D01v06 October 23, 2015 KDB 865664 D01v01r02 October 23, 2015 1.3 Refer Rules IEEE Standard for Safety Levels with Respect to Human Exposure to Radio ANSI C95.1–1999 Frequency Electromagnetic Fields, 3 kHz to 300 GHz. KDB 447498 D01 v06 October 23, Mobile and Portable Devices RF Exposure Procedures and Equipment 2015 Authorization Policies. KDB 865664 D01v01r02 October RF Exposure Compliance Reporting and Documentation Considerations. 23, 2015 CFR 47 FCC Part 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. CFR 47 FCC Part 1.1310 Radiofrequency radiation exposure limits. 1.4 EUT Technologies Wireless Frequency bands Operation mode Duty cycle Technologies 850 Voice (GMSK) 1 slot 12.5% GSM 1900 Support DTM (Dual Transfer Mode) 8 1 slot (1 Up, 4 Down) 12.5% 12.5% 10 2 slots (2 Up, 4 Down) 850 GPRS (GMSK) 25% GPRS 1900 Multi – Slot Class 12.5% 12 4 slots (4 Up, 4 Down) 25% 37.5% CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 6 of 17 50% 8 1 slot (1 Up, 4 Down) 12.5% 12.5% 10 2 slots (2 Up, 4 Down) 25% 850 EDGE (8-PSK) EDGE 12.5% 1900 Multi – Slot Class 25% 12 4 slots (4 Up, 4 Down) 37.5% 50% UMTS Rel.99 (Voice & Data) Band II HSDPA(Rel.5) WCDMA Band IV HSUPA(Rel.6) 100% (UMTS) Band V DC-HSDPA(Rel.8) HSPA+(Rel.7) 1xRTT (Voice & Data) BC0 1xEVDO Rel.0 CDMA BC1 100% 1xEVDO Rel.A (CDMA2000) BC10 1xAdvanced Support SV-DO (1xRTT-1xEVDO) Band 2 QPSK Band 4 16QAM Band 5 Band 7 Band 12 2 Uplinks 2 Downlinks Band 13 100% LTE-FDD Rel.11 Carrier 2 Uplinks 3 Downlinks Band 17 Aggregation 3 Uplinks 2 Downlinks Band 25 3 Uplinks 3 Downlinks Band 26 Band 27 Band 30 Supports SV-LTE (1xRTT-LTE) QPSK 63.3% 16QAM This device supports uplink –downlink Band 38 configuration Band 39 2 Uplinks 2 Downlinks 0-6. The Band 40 LTE-TDD Rel.11 Carrier 2 Uplinks 3 Downlinks configuration Band 41 Aggregation 3 Uplinks 2 Downlinks with highest Band 42 3 Uplinks 3 Downlinks duty cycle was used (configuration. 0 at 63.3%) Supports SV-LTE (1xRTT-LTE) 2412 – 2462 MHz IEEE 802.11b 50% 2412 – 2472 MHz 2412 – 2462 MHz IEEE 802.11g 50% 2412 – 2472 MHz 2.4GHz IEEE 802.11n 2412 – 2462 MHz 50% HT20 2412 – 2472 MHz IEEE 802.11n 2422 – 2452 MHz 50% HT40 Wi-Fi 5180 – 5240 MHz 5260 – 5320 MHz IEEE 802.11a 50% 5500 – 5700 MHz 5745 – 5825 MHz 5GHz 5180 – 5240 MHz IEEE 802.11n 5260 – 5320 MHz 50% HT20 5500 – 5700 MHz 5745 – 5825 MHz CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 7 of 17 5190 – 5230 MHz IEEE 802.11n 5270 – 5310 MHz 50% HT40 5510 – 5670 MHz 5755 – 5795 MHz 5180 – 5240 MHz IEEE 802.11ac 5260 – 5320 MHz 50% VHT20 5500 – 5700 MHz 5745 – 5825 MHz 5190 – 5230 MHz IEEE 802.11ac 5270 – 5310 MHz 50% VHT40 5510 – 5670 MHz 5755 – 5795 MHz 5210 – 5210 MHz IEEE 802.11ac 5290 – 5290 MHz 50% VHT80 5530 – 5530 MHz 5775 – 5775 MHz Supports Band gap channels 1 MHz Others 2.4GHz 2402 – 2472 MHz 100% Bandwidth Version 2.1+EDR 77.5% Version 3.0+HS 77.5% Bluetooth 2.4GHz Version 4.0 100% Version 4.1+EDR 77.5% Version 4.2+EDR 77.5% 1.5 Antenna Information Wireless Frequency bands Antenna type Maximum antenna gain Technologies PIFA PCB Antenna 0 GSM 850 PIFA PCB Antenna 1 PIFA PCB Antenna 0 GSM 1900 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band II PIFA PCB Antenna 1 PIFA PCB Antenna 0 WCDMA (UMTS) Band IV PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band V PIFA PCB Antenna 1 CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 8 of 17 PIFA PCB Antenna 0 CDMA800 PIFA PCB Antenna 1 CDMA (CDMA2000) PIFA PCB Antenna 0 CDMA1900 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 2 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 4 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 5 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 7 PIFA PCB Antenna 1 LTE-FDD PIFA PCB Antenna 0 Band 12 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 13 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 17 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 25 PIFA Antenna 1 PCB CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 9 of 17 PIFA PCB Antenna 0 Band 26 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 27 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 38 PIFA PCB Antenna 1 PIFA PCB Antenna 0 LTE-TDD Band 39 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 40 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 41 PIFA PCB Antenna 1 PIFA PCB Antenna 0 Band 42 PIFA PCB Antenna 1 PIFA PCB Antenna 0 2.6dBi gain max PIFA 2.4GHz PCB Antenna 1 PIFA PCB Antenna 2 Wi-Fi PIFA PCB Antenna 0 3.8dBi gain max 5GHz PIFA PCB Antenna 1 PIFA Antenna 2 CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 10 of 17 PCB PIFA Antenna 0 PCB PIFA Others 2.4GHz Antenna 1 PCB PIFA Antenna 2 PCB PIFA Bluetooth 2.4GHz Antenna 0 0.2dBi gain max PCB CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 11 of 17 2.6. EUT, Auxiliary Equipment (AE) and EUT set-ups Please refer to the following test reports: FCC WLAN 2.4GHz: BTL-FCCP-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 FCC BT BDR/EDR: BTL-FCCP-1-1808C227_BT_ AIVIP42M0 MDG1810008 FCC WLAN 5GHz BTL-FCCP-3-1808C227_5G_ AIVIP42M0 MDG1810008 ISED WLAN 2.4GHz: BTL-ISEDR-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 ISED BT BDR/EDR: BTL-ISEDR-1-1808C227_BT_ AIVIP42M0 MDG1810008 ISED WLAN 5GHz BTL-ISEDR-3-1808C227_5G_ AIVIP42M0 MDG1810008 2.7. EUT operating modes EUT Description of Additional information operating operating modes mode no.*) WLAN 2.4 802.11b/g/n op. 1 TX-Mode With help of special test firmware a continuous traffic mode. *2) Fixed channel modulated TX-Mode hopping With help of special test firmware a continuous traffic mode could be op. 2 off established with help of a Bluetooth base simulator. (R&S CBT32) WLAN 5 GHz 802.11a/n The EUT was put to Fixed Channel (Modulated) Continuous transmissions op. 3 TX-Mode mode with help of test software (Labtool) Fixed channel modulated *) EUT operating mode no. is used to simplify the test report. 2.8. Test mode software Test software name: Dut labtool SW version: 2.0.089 SW date: Mar. 09, 2016 Save location: Local test notebook Dell Inspiron 15-7559 CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 12 of 17 3. Measurements 3.1. Radio Frequency Exposure Evaluation §2.1091 3.1.Test location test location  CETECOM Essen   For Evaluation instruments are not needed. Results are determined by calculation based on applicants delivered Tune-Up procedure. 3.2 Evaluation Rules for FCC Standard Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane- wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. 3.3 Limits for FCC Standard Table 1: LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) (A) Limits for Occupational/Controlled Exposure Frequency range Electric field strength Magnetic field strength Power density Averaging time [MHz) [V/m] [A/m] [mW/cm²] [minutes] 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f2)* 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- 6 1500-100,000 -- -- 6 (B) Limits for General Population/Uncontrolled Exposure Frequency range Electric field strength Magnetic field strength Power density Averaging time [MHz) [V/m] [A/m] [mW/cm²] [minutes] 0.3-3.0 614 1.63 *(100) 30 3.0-30 824/f 2.19/f *(180/f²) 30 30-300 27.5 0.073 0.2 30 300-1500 - - f/1500 30 1500-100,000 - - 1.0 30 f=frequency in MHz *Plane-wave equivalent power density NOTE1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. These limits apply to amateur station licensees and members of their immediate household as discussed in the text. NOTE2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. As discussed in the text, these limits apply to neighbours living near amateur radio stations. CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 13 of 17 3.4 Requirements and limits for RSS Standard 2.5 Exemption Limits for Routine Evaluation All transmitters are exempt from routine SAR and RF exposure evaluations provided that they comply with the requirements of sections 2.5.1 or 2.5.2. If the equipment under test (EUT) meets the requirements of sections 2.5.1 or 2.5.2, applicants are only required to submit a properly signed declaration of compliance (see Annex C). The information contained in the RF exposure technical brief may be limited to the value(s) of the maximum output power, the information that demonstrates how the maximum output power of the transmitter was derived and the rationale for the separation distances applied (see Table 1), which must be based on the most conservative exposure condition for the applicable module or host platform test procedure requirements. 2.5.2 Exemption Limits for Routine Evaluation — RF Exposure Evaluation RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows:  below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance);  at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz;  at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); RSS-102, Issue 5  at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz;  at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). In these cases, the information contained in the RF exposure technical brief may be limited to information that demonstrates how the e.i.r.p. was derived. 2.6 User Manual Requirements The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions (e.g. proper accessory required, including the proper orientation of the device in the accessory, maximum antenna gain in the case of detachable antenna), in order to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual. The user manual of devices intended for controlled use shall also include information relating to the operating characteristics of the device; the operating instructions to ensure compliance with SAR and/or RF field strength limits; information on the installation and operation of accessories to ensure compliance with SAR and/or RF field strength limits; and contact information where the user can obtain Canadian information on RF exposure and compliance. Other related information may also be included. 3.5 MPE Calculation method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 EIRP P  G S  4R 2 4R 2 S  4R 2 G NUMERIC  P Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 14 of 17 R=distance to the centre of radiation of the antenna 3.7 Evaluation Method 3.7.1 Standalone Valid for WLAN/BT Mode: • The peak power was checked on 3 frequencies (lowest/middle/highest) within each operable WiFi band and the results compared to applicant’s declared power values (tune-up info). • No duty-cycle correction factor is applicable Please find in the following tables the calculations based on applicants tune-up information for the power values. Results for FCC Standard Operation Mode Frequency Declared Antenna Gain Declared Duty cycle Declared Equivalent MPE Lim it MPE-Value Margin to Fraction for Max. on channel m axim um m axim um EIRP Maxim um conducted output Lim it: conducted (Measured+ conducted pow er (output Co-Location Fraction- output Tune-up) output pow er x duty calculations Value pow er pow er cycle) within (m W/cm ^2) (dBi) (dBm ) Frequency- (MHz) (dBm ) % (W) (m W) (m W/cm ^2) (m W/cm ^2) Band 2412,0 9,9 2,6 12,5 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 W-LAN 2437,0 9,9 2,6 12,5 100% 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 0,0035378 2.4GHz 2462,0 9,9 2,6 12,5 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 2402,0 -2,20 0,2 -2,0 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 Bluetooth 2442,0 -2,20 0,2 -2,0 100% 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 0,0001255 BDR/ DER 2480,0 -2,20 0,2 -2,0 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 Operation Frequency on Declared Max. positive Declared Path Loss EIRP Duty cycle Maxim um Equivalent MPE-Value MPE-Value Margin Mode channel m axim um tolerance Antenna Gain to ext. EIRP EIRP Maximum conducted according antenna (EIRP x duty Fraction output pow er m anufacturer connector cycle) Fraction for Value 's tune-up according Co-location info m anufacturer within calculations Frequency (MHz) (dBm ) (dBi) (dB) (dBm ) (%) (W) (m W) (m W/cm ^2) (m W/cm ^2) (m W/cm ^2) band (dB) 5180,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5200,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5240,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5260,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5280,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5320,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5500,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5580,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5700,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5745,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5785,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5825,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5190,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5230,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5270,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5310,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 5510,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5550,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5670,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5755,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5795,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5270,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5310,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 5510,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 W-LAN 5GHz 5550,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5670,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 W-LAN 5GHz 5755,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5795,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 1. Output power including tune-up tolerance; 2. Output power was adjust to duty cycle at 100% if measured duty cycle less than 98%; 3. MPE evaluate distance is 20cm from user manual provide by manufacturer; 4. Depending on output power and antenna gain only the worst case is reported; CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 15 of 17 Results for RSS Standard Operation Mode Frequency Declared Antenna Gain Declared Duty cycle Declared Equivalent MPE Lim it MPE-Value Margin to Fraction for Max. on channel m axim um m axim um EIRP Maxim um conducted output Lim it: conducted (Measured+ conducted pow er (output Co-Location Fraction- output Tune-up) output pow er x duty calculations Value pow er pow er cycle) within (m W/cm ^2) (dBi) (dBm ) Frequency- (MHz) (dBm ) % (W) (m W) (m W/cm ^2) (m W/cm ^2) Band 2412,0 9,9 2,6 12,5 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 W-LAN 2437,0 9,9 2,6 12,5 100% 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 0,0035378 2.4GHz 2462,0 9,9 2,6 12,5 0,0178 17,8 1,0000 0,00354 0,9965 0,003538 2402,0 -2,20 0,2 -2,0 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 Bluetooth 2442,0 -2,20 0,2 -2,0 100% 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 0,0001255 BDR/ DER 2480,0 -2,20 0,2 -2,0 0,0006 0,6 1,0000 0,00013 0,9999 0,000126 Maxim um calculated MPE value: Low est MPE- 1,0000 [m W/cm ^2] Lim it: Highest MPE 0,0035 [m W/cm ^2] value: Low est Margin 0,9965 [m W/cm ^2] to lim it: Operation Frequency on Declared Max. positive Declared Path Loss EIRP Duty cycle Maxim um Equivalent MPE-Value MPE-Value Margin Mode channel m axim um tolerance Antenna Gain to ext. EIRP EIRP Maximum conducted according antenna (EIRP x duty Fraction output pow er m anufacturer connector cycle) Fraction for Value 's tune-up according Co-location info m anufacturer within calculations Frequency (MHz) (dBm ) (dBi) (dB) (dBm ) (%) (W) (m W) (m W/cm ^2) (m W/cm ^2) (m W/cm ^2) band (dB) 5180,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5200,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5240,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5260,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5280,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5320,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5500,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5580,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5700,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 5745,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5785,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 0,0023 (20MHZ BW) 5825,0 100% 0,011 11,48 1,0000 0,00228 0,9977 0,0023 W-LAN 5GHz 5190,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5230,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5270,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5310,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 5510,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5550,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5670,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5755,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 0,0019 (40MHz BW) 5795,0 100% 0,010 9,77 1,0000 0,00194 0,9981 0,0019 W-LAN 5GHz 5270,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5310,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 5510,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 W-LAN 5GHz 5550,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5670,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 W-LAN 5GHz 5755,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 0,0008 (80MHz BW) 5795,0 100% 0,004 3,89 1,0000 0,00077 0,9992 0,0008 Maximum calculated MPE value: 5GHz Low est MPE- 1,0000 [W/m ^2] Lim it: Highest MPE- 0,0023 [W/m ^2] value: Margin to 0,9977 [W/m ^2] lim it CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 16 of 17 3.7.3 Simultaneous Transmission MPE According to KDB447498 for Transmitters used in mobile exposure conditions for simultaneous transmission operations; ∑ of MPE ratios ≤ 1.0 W-LAN Bluetooth WLAN 2.4GHz BDR/DER 5GHz Ratio of MPE- 0,003537774 0,000125525 0 Value/Limit W-LAN 0,003537774 -- 0,003663299 0,003537774 2.4GHz Bluetooth 0,000125525 0,003663299 -- 0,000125525 BDR/DER WLAN 0,000000000 0,003537774 0,000125525 0,000000000 5GHz Maximum-Value 0,0036633 3.8 Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. The measurement results comply with the RSS-102, Issue 5. CETECOM_TR18_1_0086501T05a

Test Report 18-1-0086501T05a, Page 17 of 17 4. Measurement uncertainties, Instruments and Ancillary Please refer to the following test reports: FCC WLAN 2.4GHz: BTL-FCCP-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 FCC BT BDR/EDR: BTL-FCCP-1-1808C227_BT_ AIVIP42M0 MDG1810008 FCC WLAN 5GHz BTL-FCCP-3-1808C227_5G_ AIVIP42M0 MDG1810008 ISED WLAN 2.4GHz: BTL-ISEDR-2-1808C227_2.4G_ AIVIP42M0 MDG1810008 ISED BT BDR/EDR: BTL-ISEDR-1-1808C227_BT_ AIVIP42M0 MDG1810008 ISED WLAN 5GHz BTL-ISEDR-3-1808C227_5G_ AIVIP42M0 MDG1810008 5. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2018-10-12 END OF TEST REPORT CETECOM_TR18_1_0086501T05a


Document Created: 2018-10-16 11:38:16
Document Modified: 2018-10-16 11:38:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC