User manual

FCC ID: YAHMA-810

Users Manual

Download: PDF
FCCID_4244930

USER MANUAL MA-810 MOUNTING PARTS & FUNCTION Vibration out Chime 58mm Chime Vibration Pad Volume control On/Off Function Switch DC Jack Flasher On Cancel Off Pad Pad 12V On Ready Zone LED Indicator Melody Speaker Wall mounded selector button Put on the desk Top Zone selector button CODE MATCHING & TUNE SELECTION FunctionSwitch Step1:Insert the battery into the transmitter to be ID * Chime used (Doorbell button) * Light & Chime Battery compartment Battery cover * Light Step 2: Insert the batteries into the receiver (chime unit). POWER Step 3:Enter pairing mode for the receiver (chime unit). Press & hold the ● zone 12V DC selector button for 3 seconds. The LED in 400mA zone #1 will flash. Chime On Step 4: Press the ● zone selector button again to Zone selector Off Pad Pad 12V On Ready move to the zone you wish to pair with. Press button Melody selector the ♫ melody selector button to scroll button through the melodies. Once you hear a melody you prefer, do not press any button as the melody is set for that zone. 1.5 V e 'C' Size 'C' Size 'C' Siz 1.5V 1.5V Step 5: Once the zone & melody are selected, trigger the transmitter once to pair. If successful, the receiver (chime unit) will generate two short 3 x 'C' size tones. Press the ● zone selector button to exit the pairing mode, the system is now ready to use. To stop the Chime while the receiver (chime unit) is alerting press Setup the reset button. This Bed Shaker must be worked with the Echochime 300 when using the Deletetheremotebuttononthechimememory vibration function. First,Pressandholdthe'Learning'buttonfor3secondstoenterthelearning Bed Shaker mode.Pressthe'Learnbuttontoselectthezoneyouwanttodelete.Press On/Off Vibration out DC jack andholdboththe' Learning' and the ' Melody' button 3 seconds. The On chime will generate a tone to indicate the remote on this zone has been deleted. Off Pad 12V Pad On Ready On Change the melody/ tone on desired zone Off 12V ready indicator Pad Pad 12V On Ready First,Pressandholdthe'Learning'buttonfor3secondstoenterthelearning Pad On inducator mode.Pressthe'Learnbuttontoselectthezoneyouwanttochange.Press the'Melody'buttontoselectthenewmelody/toneandthenpushtheremote button.Youwillhearatonetoindicatethemelodyhasbeenchanged. DC jack: If using the Bed Shaker , it must be connected with a 12V 400mA AC/DC adaptor to this jack. BATTERY LOW INDICATOR 12V ready indicator: This indicator will light up, when the 12V adaptor is If a zone LED light is blinking, it indicates that the battery is low for connected correctly. this transmitter. You must replace the battery as soon as possible. Bed Shaker on/off: Slide this switch to turn on or turn off the vibration function. If the white flash at the top of the Chime blinks every 5 seconds, this Pad on indicator: If the Bed Shaker on/off switch is slide to on position, this LED indicates the receiver batteries are low. You must replace the batteries of the indicator will light up to indicate vibration function is ready. receiver. Vibration out: Plug the Bed Shaker to this jack. FCC Statement: 12V DC This equipment has been tested and found to comply with the limits for a Class B digital 400mA device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and On Off Pad Pad 12V On Ready used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the Using the Bed Shaker, it must interference by one or more of the following measures: be connected with a 12V * Reorient or relocate the receiving antenna. 400mA AC/DC adaptor * Increase the separation between the equipment and receiver. * Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must Cancel Button accept any interference received, including interference that may cause undesired operation. Pressing the 'Cancel' Button will stop the chime and light after the unit has been activated. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: Modifications to this product will void the user's authority to operate this equipment. RoHS 2002/95/EC CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCT


Document Created: 2019-04-10 16:52:17
Document Modified: 2019-04-10 16:52:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC