Test Report

FCC ID: Y9XHPIRACING00101

Test Report

Download: PDF
FCCID_2404905

FCC PART 15.247 TEST REPORT For Hobby Products International Inc. 70 Icon St, Foothill Ranch, CA 92610-3000 USA FCC ID: Y9XHPIRACING00101 Product Type: Report Type: 2CH 2.4GHz FHSS RADIO Original Report SYSTEM Test Engineer: leon Chen Report Number: RSH140821052-00 Report Date: 2014-09-18 Sula Huang Reviewed By: RF Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0.

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE ...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................4 TEST METHODOLOGY ..................................................................................................................................................4 TEST FACILITY .............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................5 EUT EXERCISE SOFTWARE ..........................................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................5 SUMMARY OF TEST RESULTS ...............................................................................................................................6 FCC §15.247 (i) & §1.1307 (b) (1) & §2.1093- RF EXPOSURE.....................................................................................7 APPLICABLE STANDARD ..............................................................................................................................................7 FCC §15.203 - ANTENNA REQUIREMENT.............................................................................................................8 APPLICABLE STANDARD ..............................................................................................................................................8 ANTENNA CONNECTOR CONSTRUCTION ......................................................................................................................8 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS...............................................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 MEASUREMENT UNCERTAINTY ....................................................................................................................................9 EUT SETUP ..................................................................................................................................................................9 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................10 TEST PROCEDURE ......................................................................................................................................................10 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................11 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................11 TEST RESULTS SUMMARY ..........................................................................................................................................11 TEST DATA ................................................................................................................................................................11 FCC §15.247(a) (1) - CHANNEL SEPARATION TEST .........................................................................................15 APPLICABLE STANDARD ............................................................................................................................................15 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................15 TEST PROCEDURE ......................................................................................................................................................15 TEST DATA ................................................................................................................................................................15 FCC §15.247(a) (1) – 20 dB BANDWIDTH TESTING ............................................................................................18 APPLICABLE STANDARD ............................................................................................................................................18 TEST PROCEDURE ......................................................................................................................................................18 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................18 TEST DATA ................................................................................................................................................................18 FCC §15.247(a) (1) (iii) - QUANTITY OF HOPPING CHANNEL TEST .............................................................21 APPLICABLE STANDARD ............................................................................................................................................21 TEST PROCEDURE ......................................................................................................................................................21 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................21 TEST DATA ................................................................................................................................................................21 FCC §15.247(a) (1) (iii) - TIME OF OCCUPANCY (DWELL TIME) ...................................................................23 APPLICABLE STANDARD ............................................................................................................................................23 FCC Part 15.247 Page 2 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 TEST PROCEDURE ......................................................................................................................................................23 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................23 TEST DATA ................................................................................................................................................................23 FCC §15.247(b) (1) - PEAK OUTPUT POWER MEASUREMENT ......................................................................26 APPLICABLE STANDARD ............................................................................................................................................26 TEST PROCEDURE ......................................................................................................................................................26 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................26 TEST DATA ................................................................................................................................................................26 FCC §15.247(d) - BAND EDGES TESTING ............................................................................................................29 APPLICABLE STANDARD ............................................................................................................................................29 TEST PROCEDURE ......................................................................................................................................................29 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................29 TEST DATA ................................................................................................................................................................29 FCC Part 15.247 Page 3 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 GENERAL INFORMATION Product Description for Equipment under Test (EUT) The Hobby Products International Inc.’s product, model number: TF-60 (FCC ID: Y9XHPIRACING00101) or ("EUT”) in this report is a 2CH 2.4GHz FHSS RADIO SYSTEM, which was measured approximately: 17.4 cm (L) x 11.2 cm (W) x 7.2 cm (H),rated input voltage: DC 6V from battery. * All measurement and test data in this report was gathered from production sample serial number: 140821052. (Assigned by BACL. Dongguan).The EUT was received on 2014-08-22. Objective This report is prepared on behalf of Hobby Products International Inc. in accordance with Part 2, Subpart J, Part 15, Subparts A, B and C of the Federal Communications Commission’s rules. The tests were performed in order to determine the EUT compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 rules. Related Submittal(s)/Grant(s) No related submittal(s). Test Methodology All measurements contained in this report were conducted with ANSI C63.4-2003, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Dongguan). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Dongguan) to collect test data is located on the No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Test site at Bay Area Compliance Laboratories Corp. (Dongguan) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 02, 2012. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2003. The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 273710. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. FCC Part 15.247 Page 4 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 SYSTEM TEST CONFIGURATION Description of Test Configuration The system was configured for testing in an engineering mode. 43 hopping channels are configured by system, and EUT was tested with low channel: 2407 MHz, middle channel: 2428MHz, and high channel: 2449MHz. Frequency Frequency Frequency Frequency Channel Channel Channel Channel (MHz) (MHz) (MHz) (MHz) 1 2407 12 2418 23 2429 34 2440 2 2408 13 2419 24 2430 35 2441 3 2409 14 2420 25 2431 36 2442 4 2410 15 2421 26 2432 37 2443 5 2411 16 2422 27 2433 38 2444 6 2412 17 2423 28 2434 39 2445 7 2413 18 2424 29 2435 40 2446 8 2414 19 2425 30 2436 41 2447 9 2415 20 2426 31 2437 42 2448 10 2416 21 2427 32 2438 43 2449 11 2417 22 2428 33 2439 / / EUT Exercise Software No exercise software was used in testing. Equipment Modifications No modification was made to the EUT. Block Diagram of Test Setup 1.0 Meter EUT N on-C onductive T able 80 cm above G round Plane 1.5 M eter FCC Part 15.247 Page 5 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 SUMMARY OF TEST RESULTS FCC Rules Description of Test Result §15.247 (i), §2.1093 RF Exposure Compliance §15.203 Antenna Requirement Compliance §15.207 (a) Conducted Emissions Not Applicable §15.205, §15.209, Radiated Emissions Compliance §15.247(d) §15.247 (a)(1) 20 dB Bandwidth Compliance §15.247(a)(1) Channel Separation Test Compliance §15.247(a)(1)(iii) Time of Occupancy (Dwell Time) Compliance §15.247(a)(1)(iii) Quantity of hopping channel Test Compliance §15.247(b)(1) Peak Output Power Measurement Compliance §15.247(d) Band Edges Compliance FCC Part 15.247 Page 6 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247 (i) & §1.1307 (b) (1) & §2.1093- RF EXPOSURE Applicable Standard According to§15.247(i) and §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB447498 D01 General RF Exposure Guidance v05r02: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. Measurement Result The maximum conducted output power= -1.48 dBm=0.71mW at 2449MHz [(max. power of channel, mW)/(min. test separation distance, mm)] · [√f(GHz)] = 0.71/5*(√2.449) = 0.22 < 3.0 So the stand-alone SAR evaluation is not necessary. FCC Part 15.247 Page 7 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.203 - ANTENNA REQUIREMENT Applicable Standard According to FCC § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Antenna Connector Construction The EUT has an internal antenna. And the antenna gain is 2 dBi and fulfills the requirement of this section. Please refer to the EUT photos. Result: Compliance. FCC Part 15.247 Page 8 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS Applicable Standard FCC §15.247 (d); §15.209; §15.205; Measurement Uncertainty Compliance or non- compliance with a disturbance limit shall be determined in the following manner： If Ulab is less than or equal to Ucispr of Table 2, then: –compliance is deemed to occur if no measured disturbance level exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level exceeds the disturbance limit. If Ulab is greater than Ucispr of Table 1, then: –compliance is deemed to occur if no measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit. Based on CISPR 16-4-2: 2011, measurement uncertainty of radiated emission at a distance of 3m at Bay Area Compliance Laboratories Corp. (Dongguan) is: 30M~200MHz: 5.0 dB 200M~1GHz: 6.2 dB 1G~6GHz: 4.45 dB 6G~18GHz: 5.23 dB Table 2 – Values of Ucispr Measurement Ucispr Radiated disturbance (electric field strength at an OATS or in a SAC) (30 MHz to 1000 MHz) 6.3 dB Radiated disturbance (electric field strength in a FAR) (1 GHz to 6 GHz) 5.2 dB Radiated disturbance (electric field strength in a FAR) (6 GHz to 18 GHz) 5.5 dB EUT Setup Below 1GHz: FCC Part 15.247 Page 9 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Above 1GHz: The radiated emission tests were performed in the 3 meters test site, using the setup accordance with the ANSI C63.4-2003. The specification used was the FCC 15.209, and FCC 15.247 limits. The spacing between the peripherals was 10 cm. EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 25 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the following configurations: Frequency Range RBW Video B/W IF B/W Detector 30 MHz – 1000 MHz 120 kHz 300 kHz 120 kHz QP 1MHz 3 MHz / PK Above 1 GHz 1MHz 10 Hz / Ave. Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz - 1 GHz, peak and Average detection modes for frequencies above 1 GHz. FCC Part 15.247 Page 10 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S EMI Test Receiver ESCI 100224 2014-05-09 2015-05-09 Sunol Antenna JB3 A060611-3 2014-07-28 2017-07-27 Sciences HP Amplifier 8447E 2434A02181 2014-09-01 2015-09-01 R&S Spectrum Analyzer FSEM DE31388 2014-05-09 2015-05-09 ETS LINDGREN Horn Antenna 3115 000 527 35 2012-09-06 2015-09-06 Mini-Circuit Amplifier ZVA-213-S+ 054201245 2014-02-19 2015-02-19 Ducommun 1007726-01 Horn Antenna ARH-4223-02 2014-06-16 2017-06-15 Technolagies 1304 QLW- Quinstar Amplifier 15964001001 2014-09-06 2015-09-06 18405536-JO * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Title 47, Part 15, Subpart C, and section 15.205, 15.209 and 15.247, with the worst margin reading of: 5.32 dB at 4898 MHz in the Horizontal polarization Test Data Environmental Conditions Temperature: 26.4°C Relative Humidity: 51% ATM Pressure: 99.7 The testing was performed by leon Chen on 2014-09-14&2014-09-15 FCC Part 15.247 Page 11 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Test Mode: Transmitting Frequency Receiver Rx Antenna Cable Amplifier Corrected FCC 15.247 Reading Detector Polar Factor loss Gain Amplitude Limit Margin (MHz) (dBμV) (PK/QP/AV) (H/V) (dB) (dB) (dB) (dBμV/m) (dBμV/m) (dB) Low Channel: 2407 MHz 2407 62.01 PK H 25.66 4.42 0.00 92.09 N/A N/A 2407 44.81 AV H 25.66 4.42 0.00 74.89 N/A N/A 2407 60.41 PK V 25.66 4.42 0.00 90.49 N/A N/A 2407 43.85 AV V 25.66 4.42 0.00 73.93 N/A N/A 2390 25.9 PK H 25.61 4.39 0.00 55.90 74.00 18.10 2390 13.47 AV H 25.61 4.39 0.00 43.47 54.00 10.53 4814 50.51 PK H 30.62 6.00 27.41 59.72 74.00 14.28 4814 37.79 AV H 30.62 6.00 27.41 47.00 54.00 7.00 7221 43.55 PK H 34.13 7.46 25.90 59.24 74.00 14.76 7221 31.05 AV H 34.13 7.46 25.90 46.74 54.00 7.26 9628 29.18 PK H 36.01 8.80 27.51 46.48 74.00 27.52 9628 18.16 AV H 36.01 8.80 27.51 35.46 54.00 18.54 1372 30.9 PK H 23.27 3.06 26.97 30.26 74.00 43.74 1372 20.18 AV H 23.27 3.06 26.97 19.54 54.00 34.46 163.3 35.17 QP H 12.55 1.56 21.44 27.84 43.50 15.66 Middle Channel: 2428 MHz 2428 62.24 PK H 25.71 4.41 0.00 92.36 N/A N/A 2428 48.21 AV H 25.71 4.41 0.00 78.33 N/A N/A 2428 60.15 PK V 25.71 4.41 0.00 90.27 N/A N/A 2428 45.93 AV V 25.71 4.41 0.00 76.05 N/A N/A 4856 51.09 PK H 30.73 6.09 27.42 60.49 74.00 13.51 4856 36.57 AV H 30.73 6.09 27.42 45.97 54.00 8.03 7284 41.62 PK H 34.28 7.49 25.89 57.50 74.00 16.50 7284 27.03 AV H 34.28 7.49 25.89 42.91 54.00 11.09 9712 28.75 PK H 36.21 8.82 27.32 46.46 74.00 27.54 9712 16.17 AV H 36.21 8.82 27.32 33.88 54.00 20.12 1307 31.03 PK H 23.10 2.93 26.91 30.15 74.00 43.85 1307 17.29 AV H 23.10 2.93 26.91 16.41 54.00 37.59 2813 32.14 PK H 26.71 5.47 27.56 36.76 74.00 37.24 2813 18.4 AV H 26.71 5.47 27.56 23.02 54.00 30.98 163.3 35.72 QP H 12.55 1.56 21.44 28.39 43.50 15.11 High Channel: 2449 MHz 2449 62.66 PK H 25.77 4.40 0.00 92.83 N/A N/A 2449 47.44 AV H 25.77 4.40 0.00 77.61 N/A N/A 2449 60.79 PK V 25.77 4.40 0.00 90.96 N/A N/A 2449 44.15 AV V 25.77 4.40 0.00 74.32 N/A N/A 2483.5 32.14 PK H 25.86 4.49 0.00 62.49 74.00 11.51 2483.5 18.01 AV H 25.86 4.49 0.00 48.36 54.00 5.64 4898 52.49 PK H 30.83 6.08 27.42 61.98 74.00 12.02 4898 39.19 AV H 30.83 6.08 27.42 48.68 54.00 5.32 7347 42.15 PK H 34.43 7.53 25.87 58.24 74.00 15.76 7347 29.79 AV H 34.43 7.53 25.87 45.88 54.00 8.12 9796 28.68 PK H 36.41 8.84 27.13 46.80 74.00 27.20 9796 15.71 AV H 36.41 8.84 27.13 33.83 54.00 20.17 1957 30.83 PK H 24.51 3.79 27.49 31.64 74.00 42.36 1957 17.59 AV H 24.51 3.79 27.49 18.40 54.00 35.60 163.3 35.49 QP H 12.55 1.56 21.44 28.16 43.50 15.34 FCC Part 15.247 Page 12 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Conducted Spurious Emissions at Antenna Port Low Channel * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -48.17 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 s 21.204560000 GHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.84 dBm 1 2.377180000 GHz A 0 D1 -1.84 dBm 1 PK MAXH Fundamental -10 LVL -20 D2 -21.84 dBm -30 -40 2 3DB -50 -60 -70 -80 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 15.SEP.2014 16:28:40 Middle Channel * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -48.64 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 s 21.204560000 GHz 10 Offset 0.5 dB Marker 1 [T1 ] -2.48 dBm 2.427120000 GHz A 0 1 D1 -2.48 dBm 1 PK MAXH -10 LVL Fundamental -20 D2 -22.48 dBm -30 -40 2 3DB -50 -60 -70 -80 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 15.SEP.2014 16:34:27 FCC Part 15.247 Page 13 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 High Channel * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -48.29 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 s 20.555340000 GHz 10 Offset 0.5 dB Marker 1 [T1 ] -2.12 dBm 1 2.427120000 GHz A 0 D1 -2.12 dBm 1 PK MAXH -10 LVL Fundamental -20 D2 -22.12 dBm -30 -40 2 3DB -50 -60 -70 -80 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 15.SEP.2014 16:40:31 FCC Part 15.247 Page 14 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(a) (1) - CHANNEL SEPARATION TEST Applicable Standard Frequency hopping systems shall have hoping channel carrier frequencies separated by a minimum of 25 kHz or the 20dB bandwidth of the hopping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.50 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20dB bandwidth of the hopping channel, whichever is greater provided the systems operate with an output power no greater than 125 mW. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Procedure Set the EUT in transmitting mode, maxhold the trace, Allow it to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. Test Data Environmental Conditions Temperature: 29.1°C Relative Humidity: 62 % ATM Pressure: 100.1Pa The testing was performed by leon Chen on 2014-09-12 Test Result: Compliance. Please refer to following tables and plots FCC Part 15.247 Page 15 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Test Mode: Transmitting Channel Frequency Limit Channel Separation Result (MHz) (MHz) (MHz) Low 2407 1.004 0.653 Pass Adjacent 2408 Middle 2428 1.004 0.653 Pass Adjacent 2429 High 2449 1.004 0.653 Pass Adjacent 2448 Note: Limit= (2/3) of 20 dB bandwidth Low Channel DELTA MARKER 1 * RBW 30 kHz Delta 1 [T1 ] 1.004 MHz * VBW 100 kHz -0.09 dB Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 1.004000000 MHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.80 dBm 1 1 2.406964000 GHz A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.4075 GHz 200 kHz/ Span 2 MHz Date: 12.SEP.2014 20:02:33 FCC Part 15.247 Page 16 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Middle Channel DELTA MARKER 1 * RBW 30 kHz Delta 1 [T1 ] 1.004 MHz * VBW 100 kHz -0.00 dB Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 1.004000000 MHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.86 dBm 1 1 2.427964000 GHz A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.4285 GHz 200 kHz/ Span 2 MHz Date: 12.SEP.2014 20:10:22 High Channel DELTA MARKER 1 * RBW 30 kHz Delta 1 [T1 ] 1.004 MHz * VBW 100 kHz 0.04 dB Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 1.004000000 MHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.74 dBm 1 1 2.447964000 GHz A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.4485 GHz 200 kHz/ Span 2 MHz Date: 12.SEP.2014 20:22:18 FCC Part 15.247 Page 17 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(a) (1) – 20 dB BANDWIDTH TESTING Applicable Standard Alternatively, frequency hopping systems operating in the 2400–2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW. Test Procedure Set the EUT in transmitting mode, maxhold the trace, Allow it to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20 dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 29.1°C-24.6°C Relative Humidity: 62 %-64 % ATM Pressure: 100.1Pa-100.7 Pa The testing was performed by leon Chen on 2014-09-12&2014-09-18. Test Result: Compliance. Please refer to following tables and plots FCC Part 15.247 Page 18 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Test Mode: Transmitting Frequency 20 dB Bandwidth Channel (MHz) (MHz) Low 2407 0.816 Middle 2428 0.980 High 2449 0.824 Please refer to the following plots. Low Channel DELTA MARKER 1 * RBW 30 kHz Delta 1 [T1 ] 816 kHz * VBW 100 kHz 0.52 dB Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 816.000000000 kHz 10 Offset 0.5 dB OBW872.000000000 kHz Marker 1 [T1 ] -21.81 dBm A 0 D1 -1.64 dBm 2.406548000 GHz 1 PK Temp 1 [T1 OBW] MAXH -10 -19.30 dBm LVL 2.406576000 GHz T1 1 Temp 2 [T1 OBW] -20 1 D2 -21.64 dBm -25.65 dBm T2 2.407448000 GHz -30 -40 3DB -50 -60 -70 -80 Center 2.407 GHz 200 kHz/ Span 2 MHz Date: 12.SEP.2014 19:55:22 FCC Part 15.247 Page 19 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Middle Channel DELTA MARKER 1 * RBW 30 kHz Delta 1 [T1 ] 980 kHz * VBW 100 kHz 0.26 dB Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 980.000000000 kHz 10 Offset 0.5 dB OBW900.000000000 kHz Marker 1 [T1 ] -22.01 dBm A 0 D1 -1.87 dBm 2.427528000 GHz 1 PK Temp 1 [T1 OBW] MAXH -10 -19.09 dBm LVL 2.427564000 GHz T1 T2 Temp 1 1 2 [T1 OBW] -20 D2 -21.87 dBm -20.32 dBm 2.428464000 GHz -30 -40 3DB -50 -60 -70 -80 Center 2.428 GHz 200 kHz/ Span 2 MHz Date: 12.SEP.2014 20:08:28 High Channel FCC Part 15.247 Page 20 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(a) (1) (iii) - QUANTITY OF HOPPING CHANNEL TEST Applicable Standard Frequency hopping systems in the 2400–2483.5 MHz band shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. Frequency hopping systems may avoid or suppress transmissions on a particular hopping frequency provided that a minimum of 15 channels are used. Test Procedure Set the EUT in hopping mode, maxhold the trace, allow it to stabilize. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 29.1°C Relative Humidity: 62 % ATM Pressure: 100.1Pa The testing was performed by leon Chen on 2014-09-12 Test Result: Compliance. Please refer to following tables and plots FCC Part 15.247 Page 21 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Test Mode: Transmitting Frequency Range Number of Limit (MHz) Hopping Channel 2400-2483.5 43 ≥15 Number of Hopping Channels DELTA MARKER 1 * RBW 100 kHz Delta 1 [T1 ] 42.585 MHz * VBW 300 kHz -0.92 dB Ref 10.5 dBm * Att 20 dB SWT 10 ms 42.585000000 MHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.67 dBm 1 2.406680000 GHz A 0 1 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Start 2.4 GHz 8.35 MHz/ Stop 2.4835 GHz Date: 12.SEP.2014 19:49:46 FCC Part 15.247 Page 22 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(a) (1) (iii) - TIME OF OCCUPANCY (DWELL TIME) Applicable Standard Frequency hopping systems in the 2400-2483.5 MHz shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. Frequency hopping systems may avoid or suppress transmissions on a particular hopping frequency provided that a minimum of 15 channels are used. Test Procedure The EUT was worked in hopping mode; Spectrum SPAN was set as zero. Sweep time was set as necessary to capture the entire dwell time per hopping channel, the quantity of pulse was get from single sweep. In addition, the time of single pulse was tested. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 29.1°C～29.2°C Relative Humidity: 62 %～63 % ATM Pressure: 100.1Pa～100.2Pa The testing was performed by leon Chen on 2014-09-15 and 2014-09-17 Test Result: Compliance. Please refer to following tables and plots Test Mode: Transmitting Pulse Width Hopping Dwell Time Limit Frequency Result (ms) Rate (s) (s) 2428 MHz 0.86 129 0.044 0.4 Pass Note: Dwell time= pulse width* hopping rate/hopping mumbers*hopping numbers*0.4 Hopping rate= 10/10*3*43 =129 pulse/second FCC Part 15.247 Page 23 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 10 hoppings per 10s RBW 1 MHz * VBW 3 MHz Ref 10 dBm * Att 20 dB SWT 10 s 10 Offset 0.5 dB A 0 SGL 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.428 GHz 1 s/ Date: 17.SEP.2014 09:32:21 3 pulse in a hopping RBW 1 MHz * VBW 3 MHz Ref 10 dBm * Att 20 dB SWT 1 s 10 Offset 0.5 dB A 0 SGL 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.428 GHz 100 ms/ Date: 17.SEP.2014 09:31:45 FCC Part 15.247 Page 24 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 860us per pulse RBW 1 MHz Delta 1 [T1 ] * VBW 3 MHz -0.04 dB Ref 10.5 dBm * Att 20 dB SWT 30 ms 860.000000 µs 10 Offset 0.5 dB Marker 1 [T1 ] -65.00 dBm -100.000000 µs A 0 SGL 1 PK * CLRWR TRG -10 TRG -10 dBm LVL -20 -30 -40 3DB -50 -60 1 1 -70 -80 Center 2.428 GHz 3 ms/ Date: 15.SEP.2014 17:55:30 FCC Part 15.247 Page 25 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(b) (1) - PEAK OUTPUT POWER MEASUREMENT Applicable Standard According to §15.247(b) (1), for frequency hopping systems operating in the 2400–2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725- 5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400–2483.5 MHz band: 0.125 watts Test Procedure Set the EUT in transmitting mode, maxhold the trace, Allow it to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 29.1°C Relative Humidity: 62 % ATM Pressure: 100.1Pa The testing was performed by leon Chen on 2014-09-12 Test Result: Compliance. Test Mode: Transmitting Frequency Peak Output Power Limit Channel (MHz) (dBm) (dBm) Low 2407 -1.61 21 Middle 2428 -1.63 21 High 2449 -1.48 21 Please refer to the following plots. FCC Part 15.247 Page 26 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Peak Output Power, Low Channel MARKER 1 * RBW 3 MHz Marker 1 [T1 ] 2.40708 GHz * VBW 3 MHz -1.61 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 2.407080000 GHz 10 Offset 0.5 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.407 GHz 1 MHz/ Span 10 MHz Date: 12.SEP.2014 20:00:25 Peak Output Power, Middle Channel MARKER 1 * RBW 3 MHz Marker 1 [T1 ] 2.42802 GHz * VBW 3 MHz -1.63 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 2.428020000 GHz 10 Offset 0.5 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.428 GHz 1 MHz/ Span 10 MHz Date: 12.SEP.2014 20:12:06 FCC Part 15.247 Page 27 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Peak Output Power, High Channel MARKER 1 * RBW 3 MHz Marker 1 [T1 ] 2.44906 GHz * VBW 3 MHz -1.48 dBm Ref 10.5 dBm * Att 20 dB SWT 2.5 ms 2.449060000 GHz 10 Offset 0.5 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.449 GHz 1 MHz/ Span 10 MHz Date: 12.SEP.2014 20:12:42 FCC Part 15.247 Page 28 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 FCC §15.247(d) - BAND EDGES TESTING Applicable Standard In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). Test Procedure 1. Set RBW of spectrum analyzer to 100 kHz with a convenient frequency span including 100 kHz bandwidth from band edge. 2. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S Spectrum Analyzer FSP 38 100478 2014-05-09 2015-05-09 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 29.1°C Relative Humidity: 62 % ATM Pressure: 100.1Pa The testing was performed by leon Chen on 2014-09-12 Test Result: Compliance FCC Part 15.247 Page 29 of 30

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RSH140821052-00 Band Edge, Left Side MARKER 4 * RBW 100 kHz Marker 4 [T1 ] 2.398755 GHz * VBW 300 kHz -49.40 dBm Ref 10.5 dBm * Att 20 dB SWT 5 ms 2.398755000 GHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.50 dBm 2.407170000 1 GHz A 0 D1 -1.5 dBm Marker 2 [T1 ] 1 PK -49.97 dBm MAXH -10 2.400000000 GHz LVL Marker 3 [T1 ] -56.91 dBm -20 D2 -21.5 dBm 2.390000000 GHz -30 -40 4 3DB 2 -50 3 -60 -70 -80 F2 F1 Start 2.38 GHz 2.75 MHz/ Stop 2.4075 GHz Date: 12.SEP.2014 19:58:54 Band Edge, Right Side MARKER 4 * RBW 100 kHz Marker 4 [T1 ] 2.45262 GHz * VBW 300 kHz -37.16 dBm Ref 10.5 dBm * Att 20 dB SWT 10 ms 2.452620000 GHz 10 Offset 0.5 dB Marker 1 [T1 ] -1.31 dBm 1 2.449118000 GHz A 0 D1 -1.31 dBm Marker 2 [T1 ] 1 PK -38.63 dBm MAXH -10 2.452500000 GHz LVL Marker 3 [T1 ] -57.54 dBm -20 D2 -21.31 dBm 2.483500000 GHz -30 4 2 -40 3DB -50 3 -60 -70 -80 F2 F1 Start 2.4485 GHz 5.15 MHz/ Stop 2.5 GHz Date: 12.SEP.2014 20:17:52 ***** END OF REPORT ***** FCC Part 15.247 Page 30 of 30


Document Created: 2014-09-28 09:55:30
Document Modified: 2014-09-28 09:55:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC