Test report

FCC ID: XVBA1B01

Test Report

Download: PDF
FCCID_1518260

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 FCC 47 CFR PART 15 SUBPART C TEST REPORT For TPM Sensor Model: PA1-007 Data Applies To : PA1-001; PA1-002; PA1-003; PA1-004; PA1-005; PA1-008; PA1-011; PA1-012; PA1-013 Trade Name: SMP Issued to Standard Motor Products, Inc. 37-18 Northern Boulevard, Long Island City, New York 11101 Issued by Compliance Certification Services Inc. Tainan Lab. No. 8, Jiu Ceng Ling, Jiaokeng Village, Sinhua Township, Tainan Hsien 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date : August 05, 2011 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 March 28, 2011 Initial Issue ALL Sunny Chang 01 May 11, 2011 Add test data Page 15 Sunny Chang 02 July 25, 2011 Update test data Page 22~24 Sunny Chang Page 03 July 29, 2011 Update test data Sunny Chang 15,17,18,22-24 Page 13-14, 04 August 05, 2011 Update test data Sunny Chang 22-24 Page 2 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .............................................................................................. 4 2. EUT DESCRIPTION ..................................................................................................................... 5 3. TEST METHODOLOGY .............................................................................................................. 6 3.1 EUT CONFIGURATION ................................................................................................................. 6 3.2 EUT EXERCISE ........................................................................................................................... 6 3.3 GENERAL TEST PROCEDURES..................................................................................................... 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS.................................................. 7 3.5 DESCRIPTION OF TEST MODES .................................................................................................... 7 4. INSTRUMENT CALIBRATION................................................................................................... 8 4.1 MEASURING INSTRUMENT CALIBRATION .................................................................................. 8 4.2 MEASUREMENT EQUIPMENT USED .................................................................................. 8 4.3 MEASUREMENT UNCERTAINTY ......................................................................................... 9 5. FACILITIES AND ACCREDITATIONS ................................................................................... 10 5.1 FACILITIES.............................................................................................................................. 10 5.2 EQUIPMENT ............................................................................................................................. 10 5.3 TABLE OF ACCREDITATIONS AND LISTINGS................................................................................. 11 6. SETUP OF EQUIPMENT UNDER TEST ................................................................................ 12 6.1 SETUP CONFIGURATION OF EUT ................................................................................................ 12 6.2 SUPPORT EQUIPMENT .............................................................................................................. 12 7. FCC PART 15.231 REQUIREMENTS..................................................................................... 13 7.1 20DB BANDWIDTH............................................................................................................... 13 7.2 LIMIT OF TRANSMISSION TIME ................................................................................................... 15 7.3 DUTY CYCLE CORRECTION FACTOR .............................................................................. 17 7.4 RADIATED EMISSIONS .............................................................................................................. 19 7.5 POWERLINE CONDUCTED EMISSIONS ........................................................................................ 26 APPENDIX I PHOTOGRAPHS OF TEST SETUP....................................................................... 27 APPENDIX 1 - PHOTOGRAPHS OF EUT Page 3 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 1. TEST RESULT CERTIFICATION Applicant: Standard Motor Products, Inc. 37-18 Northern Boulevard, Long Island City, New York 11101 Equipment Under Test: TPM Sensor Trade Name: SMP Model: PA1-007 Data Applies To PA1-001; PA1-002; PA1-003; PA1-004; PA1-005; PA1-008; PA1-011; PA1-012; PA1-013 Date of Test: October 13, 2010 ~ August 04, 2011 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.207, 15.209 and Part 15.231(e). The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Eric Huang Assistant Manager Assistant Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Page 4 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 2. EUT DESCRIPTION Product TPM Sensor Trade Name SMP Model Number PA1-007 PA1-001; PA1-002; PA1-003; PA1-004; PA1-005; PA1-008; Data Applies To PA1-011; PA1-012; PA1-013 To add a series model is for business necessary. The Model Difference products are all the same except for different model number. Power Supply battery 3Vdc Frequency Range 315 MHz Modulation Technique FSK Modulation (Single mode) Antenna Designation Monopole Antenna Remark: 1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: XVBA1B01 filing to comply with Section 15.207, 15.209 and 15.231(e) of the FCC Part 15, Subpart C Rules. Page 5 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 (2003) and FCC CFR 47 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.231(e). 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4. Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4. Page 6 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 ( 2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES After the preliminary test, the EUT (model: PA1-007 had found to emit the worst emissions and therefore had been tested under normal operating and standby condition. Hardware used to control the EUT for staying in continuous transmitting and receiving mode for testing. Page 7 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Open Area Test Site # 6 Name of Serial Manufacturer Model Calibration Due Equipment Number TYPE N COAXIAL SUHNER CHA9513 6 NOV. 17, 2011 CABLE BI-LOG Antenna Sunol JB1 A070506-2 OCT. 04, 2011 LOOP ANTENNA EMCO 6502 8905-2356 JUN. 10, 2012 Pre-Amplifier HP 8447F 2944A03817 NOV. 23, 2011 EMI Receiver R&S ESVS10 833206/012 MAY 10, 2012 RF Cable SUHNER SUCOFLEX104PEA 20520/4PEA NOV. 10, 2011 Horn Antenna Com-Power AH-118 071032 DEC. 27, 2011 Spectrum Analyzer R&S FSEK 30 835253/002 JUL. 14, 2012 AFS44-00108650-42-1 Pre-Amplifier MITEQ 1205908 NOV. 23, 2011 0P-44 Turn Table Yo Chen 001 ---------- N.C.R. Antenna Tower AR TP1000A 309874 N.C.R. Controller CT SC101 ---------- N.C.R. E-INSTRUME RF Swicth ERS-180A EC1204141 N.C.R NT TELH LTD Test S/W e-3 (5.04303e) Remark: Each piece of equipment is scheduled for calibration once a year. Page 8 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 4.3 MEASUREMENT UNCERTAINTY PARAMETER UNCERTAINTY Radiated Emission, 30 to 200 MHz ±3.59dB Test Site : OATS-6 Radiated Emission, 200 to 1000 MHz ±3.27dB Test Site : OATS-6 Radiated Emission, 1 to 26.5 GHz ± 3.20dB Power Line Conducted Emission ± 2.90dB Uncertainty figures are valid to a confidence level of 95%, k=2 Page 9 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No. 8, Jiu Ceng Ling, Jiaokeng Village,Sinhua Township, Tainan Hsien 712, Taiwan (R.O.C.) The sites are constructed in conformance with the requirements of ANSI C63.7:1992, ANSI C63.4 : 2003 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” Page 10 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. Taiwan TAF The measuring facility of laboratories has been authorized or registered by the following approval agencies. Canada Industry Canada Germany TÜV NORD Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site, http://www.ccsrf.com Page 11 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Product Manufacturer Model No. Certify No. Signal cable 1 N/A ------- ------- ------- ------- No. Signal cable description A N/A -------- Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 12 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 7. FCC PART 15.231 REQUIREMENTS 7.1 20DB BANDWIDTH LIMIT The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. Test Configuration Spectrum EUT Analyzer TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The spectrum analyzer center frequency is set to the transmitter frequency. The RBW is set to 10 kHz and VBW is set 30kHz. TEST RESULTS No non-compliance noted. Test Data Frequency 20dB Limit Bandwidth Result (MHz) (KHz) (KHz) 315 136.2725451 787.5 PASS Page 13 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Test Plot Page 14 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 7.2 LIMIT OF TRANSMISSION TIME LIMIT According to 15.231(e), in addition, devices operated under the provisions of this paragraph shall be provided with a means for automatically limiting operation so that the duration of each transmission shall not be greater than one second and the silent period between transmissions shall be at least 30 times the duration of the transmission but in no case less than 10 seconds. Test Configuration Spectrum EUT Analyzer TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The spectrum analyzer center frequency is set to the transmitter frequency. The RBW and VBW are set to 1MHz. TEST RESULTS No non-compliance noted Test Data Limit of transmission time Frequency Transmission Time Limit Result (MHz) (s) (Second) 315 0.2004 1 PASS Silent period between transmission Frequency silent period between transmissions Limit Result (MHz) (s) (Second) 315 60.460922 10 PASS Page 15 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Test Plot transmission time silent period between transmissions Page 16 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 7.3 DUTY CYCLE CORRECTION FACTOR LIMIT Nil (No dedicated limit specified in the Rules) Test Configuration EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set center frequency of spectrum analyzer = operating frequency. 4. Set the spectrum analyzer as RBW, VBW=1MHz, Span = 0Hz, Adjust Sweep = 100ms. 5. Repeat above procedures until all frequency measured were complete. TEST RESULTS No non-compliance noted Test Data Tp =200.4008ms Ton = 15.719ms*5 times= 78.595ms Factor = 20 *log(Ton / Tp) = 20 * log(78.595/100) = -2.092dB Remark: Tp>100ms. Use 100ms for calcuation. Page 17 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Test Plot Ton Tp Page 18 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 7.4 RADIATED EMISSIONS LIMIT 1. According to §15.231(e), intentional radiators may operate at a periodic rate exceeding that specified in paragraph (a) and may be employed for any type of operation, including operation prohibited in paragraph (a), provided the intentional radiator complies with the provisions of paragraphs (b) through (d) of this Section, except the field strength table in paragraph (b) is replaced by the following: Field Strength of Field Strength of Fundamental Frequency Fundamental Spurious Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 – 40.70 1000 100 70 – 130 500 50 130 – 174 500 to 1500 ** 50 to 150 ** 174 – 260 1500 150 260 – 470 1500 to 5000 ** 150 to 500 ** Above 470 5000 500 Remark: ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, uV/m at 3 meters = 22.72727(F) - 2454.545; for the band 260-470 MHz, uV/m at 3 meters = 16.6667(F) - 2833.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (mV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μV/m at 3-meter) (dBμV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 19 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Test Configuration Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp Page 20 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 21 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Below 1 GHz Operation Tx / X Mode Test Date: August 04, 2011 Mode: Temperature: 20.3°C Tested by: John Chen Humidity: 51 % RH Polarity: Ver. / Hor. Duty Freq- Antenna Cable Meter Reading Limits Emission Level Cycle Margin Uency Detector Factor Loss at 3 m(dBμV) Factor at 3 m(dBμV/m) Mode (MHz) (dB/m) (dB) Horizontal Vertical (dBμV/M) (dB) Horizontal Vertical Horizontal Vertical 315.01 14.50 2.51 48.38 36.24 87.66 -2.09 65.38 53.24 -22.28 -34.42 PK 315.01 14.50 2.51 N/A N/A 67.66 -2.09 63.29 51.15 -4.37 -16.51 AVG 629.90 19.71 3.62 20.75 19.63 67.66 -2.09 44.09 42.97 -23.57 -24.69 PK 629.90 19.71 3.62 N/A N/A 47.66 -2.09 41.99 40.87 -5.67 -6.79 AVG 945.03 23.61 4.57 18.63 18.16 67.66 -2.09 46.81 46.34 -20.85 -21.32 PK 945.03 23.61 4.57 N/A N/A 47.66 -2.09 44.72 44.25 -2.94 -3.41 AVG N/A ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- Remark: 1. Measuring frequencies from 30 MHz to the 1GHz. 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3. Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (dB) = Remark Result (dBuV/m) – Limit (dBuV/m). Page 22 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Operation Tx / Y Mode Test Date: August 04, 2011 Mode: Temperature: 20.3°C Tested by: John Chen Humidity: 51 % RH Polarity: Ver. / Hor. Duty Freq- Antenna Cable Meter Reading Limits Emission Level Cycle Margin Uency Detector Factor Loss at 3 m(dBμV) Factor at 3 m(dBμV/m) Mode (MHz) (dB/m) (dB) Horizontal Vertical (dBμV/M) (dB) Horizontal Vertical Horizontal Vertical 315.03 14.50 2.51 36.75 43.28 87.66 -2.09 53.75 60.28 -33.91 -27.38 PK 315.03 14.50 2.51 N/A N/A 67.66 -2.09 51.66 58.19 -16.00 -9.47 AVG 630.02 19.72 3.62 18.26 18.61 67.66 -2.09 41.60 41.95 -26.06 -25.71 PK 630.02 19.72 3.62 N/A N/A 47.66 -2.09 39.51 39.86 -8.15 -7.80 AVG 945.06 23.62 4.57 20.37 21.26 67.66 -2.09 48.55 49.44 -19.11 -18.22 PK 945.06 23.62 4.57 N/A N/A 47.66 -2.09 46.46 47.35 -1.20 -0.31 AVG N/A ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- Remark: 1.Measuring frequencies from 30 MHz to the 1GHz. 2.Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3.Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4.Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5.Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6.Margin (dB) = Remark Result (dBuV/m) – Limit (dBuV/m). Page 23 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Operation Tx / Z Mode Test Date: August 04, 2011 Mode: Temperature: 20.3°C Tested by: John Chen Humidity: 51 % RH Polarity: Ver. / Hor. Duty Freq- Antenna Cable Meter Reading Limits Emission Level Cycle Margin Uency Detector Factor Loss at 3 m(dBμV) Factor at 3 m(dBμV/m) Mode (MHz) (dB/m) (dB) Horizontal Vertical (dBμV/M) (dB) Horizontal Vertical Horizontal Vertical 315.03 14.50 2.51 47.68 35.80 87.66 -2.09 64.68 52.80 -22.98 -34.86 PK 315.03 14.50 2.51 N/A N/A 67.66 -2.09 62.59 50.71 -5.07 -16.95 AVG 630.06 19.72 3.62 19.06 18.11 67.66 -2.09 42.40 41.45 -25.26 -26.21 PK 630.06 19.72 3.62 N/A N/A 47.66 -2.09 40.31 39.36 -7.35 -8.30 AVG 945.11 23.62 4.57 18.34 19.97 67.66 -2.09 46.52 48.15 -21.14 -19.51 PK 945.11 23.62 4.57 N/A N/A 47.66 -2.09 44.43 46.06 -3.23 -1.60 AVG N/A ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- Remark: 1.Measuring frequencies from 30 MHz to the 1GHz. 2.Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak/average detector mode. 3.Average/quasi-peak test would be performed if the peak result were greater than the average/quasi-peak limit or as required by the applicant. 4.Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5.Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 6.Margin (dB) = Remark Result (dBuV/m) – Limit (dBuV/m). Page 24 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 Above 1 GHz No emission found between lowest internal used/generated frequency above 1 GHz (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor, no record is required. Page 25 / 31

Compliance Certification Services Inc. FCC ID: XVBA1B01 Report No.: T100914406-RP1 7.5 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range Limits (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 * Decreases with the logarithm of the frequency. Test Configuration See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. TEST PROCEDURE Not applicable (Since the EUT is powered by battery) TEST RESULTS Not applicable (Since the EUT is powered by battery) Page 26 / 31


Document Created: 2011-08-05 16:37:16
Document Modified: 2011-08-05 16:37:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC