Users Manual

FCC ID: XQCBHAWS001

Users Manual

Download: PDF
FCCID_4050318

1523 26th St. Santa Monica, CA 90404 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3 (B)/NMB-3(B) – This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The FCC ID of the device in this package can be found on the back or bottom of the device. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same of equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Ring_Flood_Freeze_Sensor_legal.indd 1 4/12/18 2:26 PM

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Protect the device from direct sunlight. Install the device at dry locations, and protect it against rain and humidity. The device may not get in contact to salt water or other conductive liquids. The device must be charged only within a building in a dry state. This device may not be disassembled and used for any other purpose. This unit, and all the components are configured for the sole purpose of providing a security system. They are not approved for individual cellular use, battery use or other mishandling. A mobile app must be used to set up the device. This device is not an Access point or Hotspot and should not be used as one. To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents Version 1.1 Ring_Flood_Freeze_Sensor_legal.indd 2 4/12/18 2:26 PM

Prevent water and ice damage at home. Contents 1. Diagram 2. Begin the setup process near your Ring Alarm Base Station. 3. When prompted, scan the QR Code or enter the PIN. Flood/Freeze Sensor Ring Flood/Freeze Sensor is a smart sensor for your Ring Alarm system. Place 1. Diagram Say hello to LED Ring S et up your In the Ring app, tap Set Up a Device. Pair your Ring This begins the pairing process. The QR Code and PIN are on the back of your your Ring Ring Flood/ Flood/Freeze For Ring Alarm it anywhere that flooding or freezing Choose Security Devices, then Sensors, sensor and in the product packaging. conditions can occur. then Ring Flood/Freeze Sensor, then tap 2. In-app Setup Flood/Freeze Add Device. When the Sensor detects water or dangerously low temperatures (around Freeze Sensor To complete the setup process, follow Sensor with 40 ° F or 4.4 ° C), Ring Alarm notifies you Sensor. Setup Button in the Ring app. the in-app instructions. your Ring Base of the problem, wherever you are. 3. Pairing the Sensor Station. 4. Physical Installation Flood Sensors 5. Additional Information

Open the lid and pull out the tab. Twist the lid to the left to unlock, then lift it Watch your Sensor connect. As your Sensor pairs to your Base Station, 4. Test your Flood/Freeze Sensor. Bring your Sensor to the area you want to Close the lid. Place the lid back on the Sensor, taking Place the Sensor on the ground. Choose a spot next to a possible source 5. How to remove this Sensor from your system: How to replace the battery: Twist the lid on the Sensor counter- to remove. Next, pull out the clear battery tab. This turns on the Sensor. its LED ring blinks slowly, then quickly. Once the Sensor is paired, the LED glows Place your Ring monitor. Push the Setup button inside the Sensor care to line up the semi-circle on the rim of the lid with the “open” semi-circle on of flooding, such as your water heater, sink, or refrigerator. Take care to place Additional Open the side menu in the Ring app and tap Devices, then Base Station. Next, clockwise and lift to remove. Replace the battery with a fresh CR123A cell. Flood/Freeze information. blue for three seconds. the base. Twist the lid clockwise to lock the Sensor in a location where it won’t be select your Sensor, then tap the gear- Your Base Station finds it automatically. to test the connection. If the LED ring it in. kicked or moved unintentionally. The Sensor then reconnects to your Ring If the Sensor does not pair successfully, blinks blue, the Sensor has connected shaped icon, and tap Remove Device. Base Station automatically. the LED ring glows red. To try the pairing process again, remove and reinstall the battery inside the Sensor. Sensor. successfully and is ready to place. When prompted, open the sensor and remove and reinstall the battery to LED status patterns: If it blinks red, try the test again. You may complete the removal. find that repositioning the Sensor (even just a few inches) can improve reception Water or low How to perform a factory reset: temperature Blue Blink (1x) and allow it to reconnect. detected Setup If your Flood/Freeze Sensor stops If the Sensor cannot connect, try installing a working or can’t connect (even with a Sensor Button Ring Range Extender between your Sensor opened Red Blinks (3x) good battery), try a factory reset. or moved and Base Station, following the included instructions. To do this, press and hold the Setup button for 10 seconds. When the LED Firmware Blue & Red Blinks updating ring stops blinking, the Sensor has reset. This process disconnects the Sensor from your Alarm Base Station. To begin using the © 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Sensor again, set it up in the Ring app. Last updated: 09/26/18


Document Created: 2018-10-26 15:14:33
Document Modified: 2018-10-26 15:14:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC