Test Report

FCC ID: XPYVERAP174

Test Report

Download: PDF
FCCID_4190160

FCC Measurement/Technical Report on 007178 VN4610 FCC ID: Contains XPYVERAP174 IC: - Test Report Reference: MDE_VECTOR_1701_FCCb_REV1 Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1.1 Applied Standards 3 1.2 Measurement Summary / Signatures 4 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 8 3.3 Ancillary Equipment 8 3.4 Auxiliary Equipment 8 3.5 EUT Setups 9 3.6 Operating Modes 9 3.7 Product labelling+ 9 4 Test Results 10 4.1 RF Output power 10 4.2 transmit spurious emissions radiated 14 5 Test Equipment 21 6 Antenna Factors, Cable Loss and Sample Calculations 23 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 23 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 24 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 25 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 26 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 27 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 28 7 Setup Drawings 29 8 Measurement Uncertainties 30 9 Photo Report 30 TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 2 of 30

Applied Standards and Test Summary 1.1 APPLIED STANDARDS Type of Authorization Certification for a DSRCS On-Board Unit. Certification for a DSRCS Roadside Unit. Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (23-10-17 Edition) and 90 (23-10-17) and 95 (23-10-17 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 90, Subpart M – Intelligent Transportation Systems Radio Service Part 95, Subpart L – DSRCS On-Board Units FCC §2.1046, §95.3167, §95.3189 & ASTM E2213-03 §8.9.1 FCC §2.1049 ASTM E2213-03 §8.9.2 FCC §2.1055 & ASTM E2213-03 §8.9.4 FCC §2.1051 & ASTM E2213-03 §8.9.2 & ASTM E2213-03 §8.9.3 FCC §2.1053 & ASTM E2213-03 §8.9.2 & ASTM E2213-03 §8.9.3 The tests were performed according ANSI C63.26:2015 TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 3 of 30

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.2 Measurement Summary / Signatures. 1.2 MEASUREMENT SUMMARY / SIGNATURES FCC §2.1046, §90.377, §95.3167 & ASTM E2213-03 §8.9.1 RF Output Power Final Result OP-Mode Setup FCC Radio Technology, Operating Frequency IEEE 802.11p, low channel Setup_02 Passed IEEE 802.11p, mid channel Setup_02 Passed IEEE 802.11p, CH 180 (5900 MHz) Setup_02 Passed IEEE 802.11p, CH 182 (5910 MHz) Setup_02 Passed IEEE 802.11p, high channel Setup_02 Passed FCC §2.1049 Emission Bandwidth Final Result OP-Mode Setup FCC Radio Technology, Operating Frequency IEEE 802.11p, low channel Setup_01 NP IEEE 802.11p, mid channel Setup_01 NP IEEE 802.11p, high channel Setup_01 NP ASTM E2213-03 §8.9.2 Transmit Spectrum Mask Final Result OP-Mode Setup FCC Radio Technology, Operating Frequency IEEE 802.11p, low channel Setup_01 NP IEEE 802.11p, mid channel Setup_01 NP IEEE 802.11p, high channel Setup_01 NP FCC §2.1055 & ASTM E2213-03 §8.9.4 Frequency Tolerance Final Result OP-Mode Setup FCC Radio Technology, Operating Frequency IEEE 802.11p, mid channel Setup_01 NP TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 4 of 30

layers A Bureau Veritas Group Company FCC §2.1051 & ASTM E2213—03 §8.9.2 & ASTM E2213—03 §8.9.3 Transmit Spurious Emissions Conducted Final Result OP—Mode Setup FCC Radio Technology, Operating Frequency TEEE 802.11p, low channel Setup_O1 NP IEEE 802.11p, mid channel Setup_O1 NP IEEE 802.11p, high channel Setup_O1 NP FCC §2.1053 & ASTM E2213—03 §8.9.2 & ASTM E2213—03 §8.9.3 Transmit Spurious Emissions Radiated Final Result OP—Mode Setup FCC Radio Technology, Operating Frequency IEEE 802.11p, low channel (MIMO) Setup_O1 Passed IEEE 802.11p, CH 180 (5900 MHz) (MIMO) Setup_O1 Passed IEEE 802.11p, high channel Setup_O1 NP NP — not performed Revision History Report version control Version Release date Change Description Version validity initial 2018—11—16 # invalid REV1 2019—02—08 * Page 1: IC number removed valid Page 3: Part 90, Subpart M — Intelligent Transportation Systems Radio Service as applicable standard added. Page 4: §90.377 added as reference for output power. Page 11: Wrong column headers in SISO table corrected. Page 11: additional comment for clarification of SISO mode added. a layers Not all tests applicable for the device have been performed. y D bPL Dipl.—Ing. Daniel Gall 7 layers GmbH, Borsigsix 40880 Ratingen, Germ: + M_‘ LL (responsible for accreditation scopefone +49 (0)2102 74Beshonsible for testing and report) Dipl.—Ing. Marco Kullik TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 5 of 30

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 Responsible for accreditation scope: Dipl.-Ing. Daniel Gall Report Template Version: 2018-04-11 2.2 PROJECT DATA Responsible for testing and report: Dipl.-Ing. Marco Kullik Employees who performed the tests: documented internally at 7Layers Date of Report: 2019-02-08 Testing Period: 2018-10-23 to 2018-10-24 2.3 APPLICANT DATA Company Name: Vector Informatik GmbH Address: Holderäckerstaße 36 70499 Stuttgart Germany Contact Person: Mr. Stefan Weber 2.4 MANUFACTURER DATA Company Name: Vector Informatik GmbH Address: Holderäckerstaße 36 70499 Stuttgart Germany Contact Person: Mr. Dominik Englert TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 6 of 30

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device IEEE 802.11p / CAN / GNSS Interface product description Product name VN4610 Type 007178 Declared EUT data by the supplier Voltage Type DC (powered via ANC1) Voltage Level EUT:12 V, DC ANC1: 120 V / 60 Hz Tested Modulation Type OFDM, ½ BPSK, 10 MHz BW Specific product The VN4610 is an interface with USB PC connection for accessing description IEEE 802.11p and CAN FD networks for on-board units and road- side units transmitting in the 5850-5925 MHz frequency band using 10 MHz bandwidth per channel. It supports data rates from 3 Mbps up to 27 Mbps and transmission and reception on 2 antennas simultaneously (TX/RX antenna diversity). Supported channels: 172, 174, 176, 178, 180, 182, 184 Ports of the device - DC in (2x): ANC1 via 2m cable connected (cables connected - USB: 2m USB Certified Hi-Speed cable connected during testing) - WLAN p Antenna Port (2x): 2 antennas connected - GNSS Port: ANC2 via 3m antenna cable connected - Ethernet: 1 m shielded CAT5e cable connected - CAN bus port (2x): CH3 & CH4: looped via 3m shielded CAN bus cable - CH6-IO: 3 m terminated shielded CAN bus cable connected Antenna External antennas, 5.9 dBi gain (value used for E.I.R.P. calculation, tested without antennas) Tested Datarates 3 Mbps Special software used Vector CANoe software running on Windows 7 laptop for testing The main components of the EUT are listed and described in chapter 3.2 EUT Main components. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 7 of 30

3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description EUT B DE1327000aa02 Standard Sample Sample Parameter Value Serial No. 000265 HW Version 3.0 SW Version 10.8.22 Comment NOTE:The short description is used to simplify the identification of the EUT in this test report. 3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, HW, SW, S/N) ANC1 FRIWO Gerätebau GmbH, MSIG-REM- AC/DC Adapter FGG-FW7520-12, -, -, - ANC2 Taoglas, AA.162, -, -, 162TT18290312 Active GPS/GLONASS Antenna ANC3 Taoglas, TD.10.5113, -, -, - 5.9GHz DSRC Antenna SMA, Article number: 07204 ANC4 Taoglas, TD.10.5113, -, -, - 5.9GHz DSRC Antenna SMA, Article number: 07204 3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) - - - TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 8 of 30

3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale Setup_01 EUT B + ANC1 + ANC2 + ANC3 + Radiated Test Setup ANC4 Setup_02 EUT B + ANC1 Conducted Test Setup 3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.6.1 TEST CHANNELS Channel 172 (low) 178 (mid) 180 182 184 (high) Frequency [MHz] 5860 5890 5900 5910 5920 3.6.1 POWER SETTINGS The power was set to the maximum possible value possible by the SW of the EUT. The duty cycle was appr. 98 % for all tests. 3.7 PRODUCT LABELLING+ 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 9 of 30

4 TEST RESULTS 4.1 RF OUTPUT POWER Standard FCC Part 95 Subpart L and FCC Part 90 Subpart M The test was performed according to: FCC §2.1046, §95.3167 & ASTM E2213-03 §8.9.1 4.1.1 TEST DESCRIPTION The Equipment Under Test (EUT) was set up to perform the output power measurements. The results recorded were measured with the modulation which produces the worst-case (highest) output power. The reference level of the spectrum analyzer was set higher than the output power of the EUT. The EUT was connected to the spectrum analyzer via a short coax cable with a known loss. Analyzer settings: • Resolution Bandwidth (RBW): 1 MHz • Video Bandwidth (VBW): 3 MHz • Trace: Average (Power Averaging) • Sweeps: 1000 • Sweeptime: coupled • Detector: RMS • Trigger: gated on IF Power The channel power function of the spectrum analyser was used (Used channel bandwidth = nominal bandwidth) 4.1.2 TEST REQUIREMENTS / LIMITS According to ASTM E2213-03 §8.9.1, Private OBU operations in Channels 172, 174, 176, 178 and 184 shall not exceed 28.8 dBm antenna input power and 33 dBm EIRP. Private OBU operations in Channel 175 shall not exceed 10 dBm antenna input power and 23 dBm EIRP. Private OBU operations in Channels 180, 181 and 182 shall not exceed 20 dBm antenna input power and 23 dBm EIRP. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 10 of 30

4.1.3 TEST PROTOCOL Ambient temperature: 24 °C Air Pressure: 1017 hPa Humidity: 37 % SISO Operation E.I.R.P. Margin Margin Max Limit Limit to Limit to Limit Verdict Power Power Antenna Max. E.I.R.P. conducted conducted cond. E.I.R.P. Channel Frequency Antenna 1 Antenna 2 Gain Power Power power power power power No. [MHz] [dBm] [dBm] [dBi] [dBm] [dBm] [dBm] [dBm] [dB] [dB] 172 5860 17.7 17.5 5.9 17.7 23.6 28.8 33.0 11.1 9.4 Passed 178 5890 17.2 16.9 5.9 17.2 23.1 28.8 33.0 11.6 9.9 Passed 180 5900 15.3 14.5 5.9 15.3 21.2 20.0 23.0 4.7 1.8 Passed 182 5910 15.6 14.5 5.9 15.6 21.5 20.0 23.0 4.4 1.5 Passed 184 5920 17.0 16.4 5.9 17.0 22.9 28.8 33.0 11.8 10.1 Passed Note: Either antenna 1 or 2 is used. The margins are calculated for the antenna port with the highest output power for each frequency. MIMO Operation E.I.R.P. Margin Margin E.I.R.P. Limit Limit to Limit to Limit Verdict Power Power Antenna Combined Combined conducted conducted cond. E.I.R.P. Channel Frequency Antenna 1 Antenna 2 Gain Power Power power power power power No. [MHz] [dBm] [dBm] [dBi] [dBm] [dBm] [dBm] [dBm] [dB] [dB] 172 5860 17.1 16.5 5.9 19.8 25.7 28.8 33.0 9.0 7.3 Passed 178 5890 16.8 15.9 5.9 19.4 25.3 28.8 33.0 9.4 7.7 Passed 180 5900 12.8 11.8 5.9 15.3 21.2 20.0 23.0 4.7 1.8 Passed 182 5910 12.5 11.7 5.9 15.1 21.0 20.0 23.0 4.9 2.0 Passed 184 5920 16.3 15.3 5.9 18.8 24.7 28.8 33.0 10.0 8.3 Passed Remark: Please see next sub-clause for the measurement plot (for bold printed values). TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 11 of 30

4.1.4MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Antenna 1, Ch. 172 (SISO) Antenna 2, Ch. 172 (SISO TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 12 of 30

Antenna 1, Ch. 180 (MIMO) Antenna 2, Ch. 180 (MIMO) 4.1.5TEST EQUIPMENT USED Radio Lab TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 13 of 30

4.2 TRANSMIT SPURIOUS EMISSIONS RADIATED Standard FCC Part 95 Subpart L and FCC Part 90 Subpart M The test was performed according to: ANSI C63.26 4.2.1TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.26 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz - IF–Bandwidth: 100 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 100 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 14 of 30

Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 100 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 2. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Above 26 GHz the measurement distance is reduced to 1 m. Step 2: Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 100 kHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 100 kHz - Measuring time: 1 s 4.2.2TEST REQUIREMENTS / LIMITS According to ASTM E2213-03 §8.9.2.2 the transmitted spectral mask for Class A, B, C and D devices are shown in Figs. 12-15. In addition, all DSRC site installations shall limit the EIRP in the transmitted spectrum to -25 dBm or less in the 100 kHz at the channel edges and the band edges. Additional filtering that supplements the filtering provided by the transmitter may be needed for some antenna/transmitter combinations. The DSRC transmitted spectrum mask is relative to the device class of operation. The power in the transmitted spectrum for all DSRC devices shall be -25 dBm or less within 100 kHz outside all channel and band edges. This will be accomplished by attenuation the transmitted signal 100 kHz outside the channel and band edges by 55 + 10log(p) dB, where P is the total transmitted power in watts. The transmitted spectral density of the transmitted signal for all TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 15 of 30

devices shall fall within the spectral mask, as detailed in Table 10. The measurements shall be made using a 100 kHz resolution bandwidth and 30 kHz video bandwidth. ASTM E2213-03 §8.9.3 Spurious transmissions from compliant devices shall comply with national regulations. 4.2.3TEST PROTOCOL Ambient temperature: 23 °C Air Pressure: 1016 - 1021 hPa Humidity: 35 - 39 % MIMO Mode Spurious Margin Transmitter Spurious Level Peak RBW Limit to Frequency Antenna Frequency Verdict Detector [kHz] [dBm] Limit [MHz] [MHz] [dBm] [dB] ANC3 5860 ANC4 - - - - - Passed ANC3 5900 ANC4 - - - - - Passed Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 16 of 30

4.2.4 MEASUREMENT PLOTS 30 MHz – 1 GHz 0 -10 -20 FCC_95 -30 -40 Level in dBm -50 -60 -70 -80 -90 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz TX frequency 5860 MHz 0 -10 -20 FCC_95 -30 -40 Level in dBm -50 -60 -70 -80 -90 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz TX frequency 5900 MHz TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 17 of 30

1 GHz – 26 GHz 30 20 10 5.859005000 GHz 0 13.306 dBm -10 -20 FCC_95 -30 Level in dBm -40 -50 -60 -70 -80 -90 -100 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz TX frequency 5860 MHz TX frequency 5860 MHz, the peak above the limit is not to be compared against the limit since it is the intentional transmitter 30 5.899882500 GHz 20 8.228 dBm 10 0 -10 -20 FCC_95 -30 Level in dBm -40 -50 -60 -70 -80 -90 -100 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz TX frequency 5900 MHz TX frequency 5900 MHz, the peak above the limit is not to be compared against the limit since it is the intentional transmitter TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 18 of 30

26 GHz – 40 GHz FCC_95 -25 -30 -35 -40 -45 Level in dBm -50 -55 -60 -65 -70 -75 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Frequency in GHz Horizontal antenna polarisation TX on CH 172 (5860 MHz) FCC_95 -25 -30 -35 -40 -45 Level in dBm -50 -55 -60 -65 -70 -75 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Frequency in GHz Vertical antenna polarisation TX on 5860 TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 19 of 30

FCC_95 -25 -30 -35 -40 -45 Level in dBm -50 -55 -60 -65 -70 -75 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Frequency in GHz Horizontal antenna polarisation TX on CH 180 (5900 MHz) FCC_95 -25 -30 -35 -40 -45 Level in dBm -50 -55 -60 -65 -70 -75 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Frequency in GHz Vertical antenna polarisation TX on CH 180 (5900 MHz) 4.2.5TEST EQUIPMENT USED Radiated Emissions TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 20 of 30

5 TEST EQUIPMENT 1 Radio Lab Conducted Radio Test Lab Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 1.2 Opus10 THI ThermoHygro Lufft Mess- und 7482 2017-03 2019-03 (8152.00) Datalogger 03 Regeltechnik (Environ) GmbH 1.3 SMB100A Signal Rohde & Schwarz 107695 2017-07 2020-07 Generator 9 kHz - 6 GHz 1.4 VT 4002 Climatic Vötsch 58566002150010 2018-04 2020-04 Chamber 1.5 FSV30 Signal Analyzer Rohde & Schwarz 103005 2018-04 2020-04 10 Hz - 30 GHz 1.6 SMBV100A Vector Signal Rohde & Schwarz 259291 2016-10 2019-10 Generator 9 kHz - 6 GHz 1.7 MFS Rubidium Datum-Beverly 5489/001 2018-07 2019-07 Frequency Standard 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 MFS Rubidium Datum GmbH 002 2018-10 2019-10 Frequency Normal MFS 2.2 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik Datalogger 13 GmbH (Environ) 2.3 Anechoic 10.58 x 6.38 x Frankonia none 2018-06 2021-06 Chamber 6.00 m³ 2.4 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-07 2021-07 biconicals 2.5 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 2.6 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 2.7 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2018-06 2020-06 Room 4.60m x PRB 4.05m (l x w x h) 2.8 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 21 of 30

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.9 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 2.10 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer 2.11 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 2.12 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 2.13 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 2.14 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 2.15 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 2.16 TT 1.5 WI Turn Table Maturo GmbH - 2.17 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 2.18 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 2.19 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 2.20 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2018-01 2021-01 2.21 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik (Environ) GmbH 2.22 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2016-11 2018-11 Spectrum Analyzer 2.23 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 2.24 AS 620 P Antenna mast HD GmbH 620/37 2.25 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/379070 (Rohacell) 9 2.26 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 2.27 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 2.28 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/11920 513 2.29 HF 907 Double-ridged Rohde & Schwarz 102444 2018-07 2021-07 horn 2.30 HF 906 Double-ridged Rohde & Schwarz 357357/001 2018-03 2021-03 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 22 of 30

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0,15 10,1 0,1 10,0 5 10,3 0,1 10,2 7 10,5 0,2 10,3 10 10,5 0,2 10,3 12 10,7 0,3 10,4 14 10,7 0,3 10,4 16 10,8 0,4 10,4 18 10,9 0,4 10,5 20 10,9 0,4 10,5 22 11,1 0,5 10,6 24 11,1 0,5 10,6 26 11,2 0,5 10,7 28 11,2 0,5 10,7 30 11,3 0,5 10,8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 23 of 30

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0,009 20,50 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,01 20,45 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,015 20,37 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,02 20,36 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,025 20,38 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,03 20,32 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,05 20,35 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,08 20,30 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,1 20,20 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,2 20,17 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,3 20,14 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,49 20,12 -79,6 0,1 0,1 0,1 0,1 -80 300 3 0,490001 20,12 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,5 20,11 -39,6 0,1 0,1 0,1 0,1 -40 30 3 0,8 20,10 -39,6 0,1 0,1 0,1 0,1 -40 30 3 1 20,09 -39,6 0,1 0,1 0,1 0,1 -40 30 3 2 20,08 -39,6 0,1 0,1 0,1 0,1 -40 30 3 3 20,06 -39,6 0,1 0,1 0,1 0,1 -40 30 3 4 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 5 20,05 -39,5 0,2 0,1 0,1 0,1 -40 30 3 6 20,02 -39,5 0,2 0,1 0,1 0,1 -40 30 3 8 19,95 -39,5 0,2 0,1 0,1 0,1 -40 30 3 10 19,83 -39,4 0,2 0,1 0,2 0,1 -40 30 3 12 19,71 -39,4 0,2 0,1 0,2 0,1 -40 30 3 14 19,54 -39,4 0,2 0,1 0,2 0,1 -40 30 3 16 19,53 -39,3 0,3 0,1 0,2 0,1 -40 30 3 18 19,50 -39,3 0,3 0,1 0,2 0,1 -40 30 3 20 19,57 -39,3 0,3 0,1 0,2 0,1 -40 30 3 22 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 24 19,61 -39,3 0,3 0,1 0,2 0,1 -40 30 3 26 19,54 -39,3 0,3 0,1 0,2 0,1 -40 30 3 28 19,46 -39,2 0,3 0,1 0,3 0,1 -40 30 3 30 19,73 -39,1 0,4 0,1 0,3 0,1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 24 of 30

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18,6 0,6 0,29 0,04 0,23 0,02 0,0 3 3 50 6,0 0,9 0,39 0,09 0,32 0,08 0,0 3 3 100 9,7 1,2 0,56 0,14 0,47 0,08 0,0 3 3 150 7,9 1,6 0,73 0,20 0,59 0,12 0,0 3 3 200 7,6 1,9 0,84 0,21 0,70 0,11 0,0 3 3 250 9,5 2,1 0,98 0,24 0,80 0,13 0,0 3 3 300 11,0 2,3 1,04 0,26 0,89 0,15 0,0 3 3 350 12,4 2,6 1,18 0,31 0,96 0,13 0,0 3 3 400 13,6 2,9 1,28 0,35 1,03 0,19 0,0 3 3 450 14,7 3,1 1,39 0,38 1,11 0,22 0,0 3 3 500 15,6 3,2 1,44 0,39 1,20 0,19 0,0 3 3 550 16,3 3,5 1,55 0,46 1,24 0,23 0,0 3 3 600 17,2 3,5 1,59 0,43 1,29 0,23 0,0 3 3 650 18,1 3,6 1,67 0,34 1,35 0,22 0,0 3 3 700 18,5 3,6 1,67 0,42 1,41 0,15 0,0 3 3 750 19,1 4,1 1,87 0,54 1,46 0,25 0,0 3 3 800 19,6 4,1 1,90 0,46 1,51 0,25 0,0 3 3 850 20,1 4,4 1,99 0,60 1,56 0,27 0,0 3 3 900 20,8 4,7 2,14 0,60 1,63 0,29 0,0 3 3 950 21,1 4,8 2,22 0,60 1,66 0,33 0,0 3 3 1000 21,6 4,9 2,23 0,61 1,71 0,30 0,0 3 3 (dLimit = 10 m) 30 18,6 -9,9 0,29 0,04 0,23 0,02 -10,5 10 3 50 6,0 -9,6 0,39 0,09 0,32 0,08 -10,5 10 3 100 9,7 -9,2 0,56 0,14 0,47 0,08 -10,5 10 3 150 7,9 -8,8 0,73 0,20 0,59 0,12 -10,5 10 3 200 7,6 -8,6 0,84 0,21 0,70 0,11 -10,5 10 3 250 9,5 -8,3 0,98 0,24 0,80 0,13 -10,5 10 3 300 11,0 -8,1 1,04 0,26 0,89 0,15 -10,5 10 3 350 12,4 -7,9 1,18 0,31 0,96 0,13 -10,5 10 3 400 13,6 -7,6 1,28 0,35 1,03 0,19 -10,5 10 3 450 14,7 -7,4 1,39 0,38 1,11 0,22 -10,5 10 3 500 15,6 -7,2 1,44 0,39 1,20 0,19 -10,5 10 3 550 16,3 -7,0 1,55 0,46 1,24 0,23 -10,5 10 3 600 17,2 -6,9 1,59 0,43 1,29 0,23 -10,5 10 3 650 18,1 -6,9 1,67 0,34 1,35 0,22 -10,5 10 3 700 18,5 -6,8 1,67 0,42 1,41 0,15 -10,5 10 3 750 19,1 -6,3 1,87 0,54 1,46 0,25 -10,5 10 3 800 19,6 -6,3 1,90 0,46 1,51 0,25 -10,5 10 3 850 20,1 -6,0 1,99 0,60 1,56 0,27 -10,5 10 3 900 20,8 -5,8 2,14 0,60 1,63 0,29 -10,5 10 3 950 21,1 -5,6 2,22 0,60 1,66 0,33 -10,5 10 3 1000 21,6 -5,6 2,23 0,61 1,71 0,30 -10,5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 25 of 30

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24,4 -19,4 0,99 0,31 -21,51 0,79 2000 28,5 -17,4 1,44 0,44 -20,63 1,38 3000 31,0 -16,1 1,87 0,53 -19,85 1,33 4000 33,1 -14,7 2,41 0,67 -19,13 1,31 5000 34,4 -13,7 2,78 0,86 -18,71 1,40 6000 34,7 -12,7 2,74 0,90 -17,83 1,47 7000 35,6 -11,0 2,82 0,86 -16,19 1,46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31,0 -23,4 0,47 1,87 0,53 -27,58 1,33 4000 33,1 -23,3 0,56 2,41 0,67 -28,23 1,31 5000 34,4 -21,7 0,61 2,78 0,86 -27,35 1,40 6000 34,7 -21,2 0,58 2,74 0,90 -26,89 1,47 7000 35,6 -19,8 0,66 2,82 0,86 -25,58 1,46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35,6 -57,3 0,56 1,28 -62,72 2,66 0,94 1,46 8000 36,3 -56,3 0,69 0,71 -61,49 2,84 1,00 1,53 9000 37,1 -55,3 0,68 0,65 -60,80 3,06 1,09 1,60 10000 37,5 -56,2 0,70 0,54 -61,91 3,28 1,20 1,67 11000 37,5 -55,3 0,80 0,61 -61,40 3,43 1,27 1,70 12000 37,6 -53,7 0,84 0,42 -59,70 3,53 1,26 1,73 13000 38,2 -53,5 0,83 0,44 -59,81 3,75 1,32 1,83 14000 39,9 -56,3 0,91 0,53 -63,03 3,91 1,40 1,77 15000 40,9 -54,1 0,98 0,54 -61,05 4,02 1,44 1,83 16000 41,3 -54,1 1,23 0,49 -61,51 4,17 1,51 1,85 17000 42,8 -54,4 1,36 0,76 -62,36 4,34 1,53 2,00 18000 44,2 -54,7 1,70 0,53 -62,88 4,41 1,55 1,91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 26 of 30

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40,2 -23,5 0,72 -35,85 6,20 2,81 2,65 18500 40,2 -23,2 0,69 -35,71 6,46 2,76 2,59 19000 40,2 -22,0 0,76 -35,44 6,69 3,15 2,79 19500 40,3 -21,3 0,74 -35,07 7,04 3,11 2,91 20000 40,3 -20,3 0,72 -34,49 7,30 3,07 3,05 20500 40,3 -19,9 0,78 -34,46 7,48 3,12 3,15 21000 40,3 -19,1 0,87 -34,07 7,61 3,20 3,33 21500 40,3 -19,1 0,90 -33,96 7,47 3,28 3,19 22000 40,3 -18,7 0,89 -33,57 7,34 3,35 3,28 22500 40,4 -19,0 0,87 -33,66 7,06 3,75 2,94 23000 40,4 -19,5 0,88 -33,75 6,92 3,77 2,70 23500 40,4 -19,3 0,90 -33,35 6,99 3,52 2,66 24000 40,4 -19,8 0,88 -33,99 6,88 3,88 2,58 24500 40,4 -19,5 0,91 -33,89 7,01 3,93 2,51 25000 40,4 -19,3 0,88 -33,00 6,72 3,96 2,14 25500 40,5 -20,4 0,89 -34,07 6,90 3,66 2,22 26000 40,5 -21,3 0,86 -35,11 7,02 3,69 2,28 26500 40,5 -21,1 0,90 -35,20 7,15 3,91 2,36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 27 of 30

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26,5 43,4 -11,2 4,4 -15,6 3 0,5 27,0 43,4 -11,2 4,4 -15,6 3 0,5 28,0 43,4 -11,1 4,5 -15,6 3 0,5 29,0 43,5 -11,0 4,6 -15,6 3 0,5 30,0 43,5 -10,9 4,7 -15,6 3 0,5 31,0 43,5 -10,8 4,7 -15,6 3 0,5 32,0 43,5 -10,7 4,8 -15,6 3 0,5 33,0 43,6 -10,7 4,9 -15,6 3 0,5 34,0 43,6 -10,6 5,0 -15,6 3 0,5 35,0 43,6 -10,5 5,1 -15,6 3 0,5 36,0 43,6 -10,4 5,1 -15,6 3 0,5 37,0 43,7 -10,3 5,2 -15,6 3 0,5 38,0 43,7 -10,2 5,3 -15,6 3 0,5 39,0 43,7 -10,2 5,4 -15,6 3 0,5 40,0 43,8 -10,1 5,5 -15,6 3 0,5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 28 of 30

7 SETUP DRAWINGS Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 29 of 30

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty AC Power Line Power ± 3.4 dB Field Strength of spurious radiation Power ± 5.5 dB 6 dB / 26 dB / 99% Bandwidth Power ± 2.9 dB Frequency ± 11.2 kHz Conducted Output Power Power ± 2.2 dB Band Edge Compliance Power ± 2.2 dB Frequency ± 11.2 kHz Frequency Stability Frequency ± 25 Hz Power Spectral Density Power ± 2.2 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_VECTOR_1701_FCCb_REV1 Page 30 of 30


Document Created: 2019-02-25 22:23:57
Document Modified: 2019-02-25 22:23:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC