MDE_UBLOX_1807_FCCh_rev01-FINAL-2019-03-18

FCC ID: XPYTOBYL210

Test Report

Download: PDF
FCCID_4218493

FCC Measurement/Technical Report on TOBY-L210 LTE/3G/2G data and voice module acc. to FCC Part 27 Subpart C FCC ID: XPYTOBYL210 IC: 8595A-TOBYL210 Test Report Reference: MDE_UBLOX_1807_FCCh_rev01 Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 5 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 7 3.3 Ancillary Equipment 8 3.4 Auxiliary Equipment 8 3.5 EUT Setups 8 3.6 Operating Modes 9 3.7 Product labelling 9 4 Test Results 10 4.1 RF power output 10 5 Test Equipment 20 6 Antenna Factors, Cable Loss and Sample Calculations 22 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 22 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 23 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 24 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 25 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 26 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 27 7 Measurement Uncertainties 28 8 Photo Report 28 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 2 of 28

Applied Standards and Test Summary 1.1 APPLIED STANDARDS Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 27, (10/1/17 Edition). The following subparts are applicable to the results in this test report. Part 27, Subpart C – Technical Standards § 27.50 – Power limits and duty cycle § 27.51 – Field strength of spurious radiation The tests were selected and performed with reference to:  FCC Public Notice 971168 applying “Measurement guidance for certification of licensed digital transmitters” 971168 D01 v03,2017-10-27  ANSI C63.26: 2015 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 3 of 28

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for Cellular Radiotelephone Service from FCC and ISED Canada Measurement FCC reference ISED reference RF Power Output §2.1046 RSS-GEN Issue 5, 6.12 §27.50 RSS-199 Issue 3, 4.4 Field strength of spurious §2.1053 RSS-GEN Issue 5, 6.13 radiation §27.51 RSS-199 Issue 3: 4.5 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 4 of 28

— ‘layers A Bureau Veritas Group Company 1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 27 Subpart C §2.1046, §27.50 RF Power Output The measurement was performed according to ANSI C63.26, KDB Final Result 971168 DO1 v03,2017—10—27 OP—Mode Setup FCC IC Frequency Band, Modulation, Channel, Frequency LTE eFDD7, QPSK, 21100, 2535 MHz S01_AAO1 Passed Passed LTE eFDD7, 16QAM, 21100, 2535 MHz So1_AA01 Passed Passed 47 CFR CHAPTER I FCC PART 27 Subpart C §2.1053, §27.51 Field strength of spurious radiation The measurement was performed according to ANSI C63.26 Final Result OP—Mode Setup FCC IC Frequency Band, Modulation, Channel, Frequency LTE eFDD7, QPSK, 21100, 2535 MHz $02_AAO1 Passed Passed Revision History Report version control Version Release date Change Description Version validity initial 2019—02—21 == invalid revO1 2019—03—18 ISED reference changed on page 4 valid COMMENT: On applicants demand not all applicable tests were tested. / ¢ . D. Ep (responsible for accreditation sco e) | \%& yoolt ( esp{':msible for testing and report) 7% ayers Dip!.—Ing. Daniel Gaf £7 l \T B.Sc. Jens Dérwald n 7 layers GmbH, Borsigstr. 11 40880 Ratingen, Germany Phone +49 (0)2102 749 0 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_revO1 Page 5 of 28

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany FCC designation number: DE0015 This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 Responsible for accreditation scope: Dipl.-Ing. Daniel Gall Report Template Version: 2017-07-14 2.2 PROJECT DATA Responsible for testing and report: B.Sc. Jens Dörwald Employees who performed the tests: documented internally at 7Layers Date of Report: 2019-03-18 Testing Period: 2018-12-18 to 2019-01-11 2.3 APPLICANT DATA Company Name: u-blox AG Address: u-blox AG CH-8800 Thalwil Switzerland Contact Person: Mr. Giulio Comar 2.4 MANUFACTURER DATA Company Name: please see applicant data Address: Contact Person: TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 6 of 28

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device GSM / UMTS and LTE module. product description Product name TOBY-L210 LTE/3G/2G data and voice module Type - Declared EUT data by the supplier General Product The EUT is a GSM / UMTS and LTE module. Description Voltage Type DC Voltage Level 3.8 V The main components of the EUT are listed and described in chapter 3.2 EUT Main components. 3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description DE1015018 aa01 radiated & conducted sample Sample Parameter Value Serial Number 352250614763 HW Version 192E01 SW Version v16.16 Comment - NOTE:The short description is used to simplify the identification of the EUT in this test report. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 7 of 28

3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) - - - 3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) AUX1 UBLOX, EVB-WL3, -, - Evaluation board AUX2 Taoglas, -, -, - External Cellular Antenna 3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale S01_AA01 aa01 + AUX1 Setup for conducted tests S02_AA01 aa01 + AUX1 + AUX2 Setup for radiated tests TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 8 of 28

3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. 3.6.1 TEST CHANNELS Center Frequency Band Uplink Channel [MHz] eFDD 7 21100 2535 3.7 PRODUCT LABELLING 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 9 of 28

4 TEST RESULTS 4.1 RF POWER OUTPUT Standard FCC Part 27, §27.50 The test was performed according to: ANSI C63.26, KDB 935210 D05 v01r01: 3.5 4.1.1 TEST DESCRIPTION The EUT was connected to the test setup according to the following diagram: The attenuation of the measuring and stimulus path are known for each measured frequency and are considered. The Spectrum Analyzer settings can be directly found in the measurement diagrams. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 10 of 28

4.1.2 TEST REQUIREMENTS / LIMITS §2,0146 Measurements Required: RF Power Output (a) For transmitters other than single sideband, independent sideband and controlled carrier radiotelephone, power output shall be measured at the RF output terminals when the transmitter is adjusted in accordance with the tune-up procedure to give the values of current and voltage on the circuit elements specified in §2.1033(c)(8). The electrical characteristics of the radio frequency load attached to the output terminals when this test is made shall be stated. FCC Part 27, § 27.50 (h) The following power limits shall apply in the BRS and EBS: (1) Main, booster and base stations. (i) The maximum EIRP of a main, booster or base station shall not exceed 33 dBW + 10log(X/Y) dBW, where X is the actual channel width in MHz and Y is either 6 MHz if prior to transition or the station is in the MBS following transition or 5.5 MHz if the station is in the LBS and UBS following transition, except as provided in paragraph (h)(1)(ii) of this section. (ii) If a main or booster station sectorizes or otherwise uses one or more transmitting antennas with a non-omnidirectional horizontal plane radiation pattern, the maximum EIRP in dBW in a given direction shall be determined by the following formula: EIRP = 33 dBW + 10 log(X/Y) dBW + 10 log(360/beamwidth) dBW, where X is the actual channel width in MHz, Y is either (i) 6 MHz if prior to transition or the station is in the MBS following transition or (ii) 5.5 MHz if the station is in the LBS and UBS following transition, and beamwidth is the total horizontal plane beamwidth of the individual transmitting antenna for the station or any sector measured at the half-power points. (2) Mobile and other user stations. Mobile stations are limited to 2.0 watts EIRP. All user stations are limited to 2.0 watts transmitter output power. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 11 of 28

4.1.3 TEST PROTOCOL RMS Ressource Conducted Radio Technology CH Bandwidth (MHz) Blocks Power (dBm) eFDD 7 QPSK mid 1 5 21.82 eFDD 7 QPSK mid 12 5 20.56 eFDD 7 QPSK mid 25 5 20.68 eFDD 7 16QAM mid 1 5 21.02 eFDD 7 16QAM mid 25 5 19.61 eFDD 7 QPSK mid 1 10 22.03 eFDD 7 QPSK mid 50 10 21.02 eFDD 7 16QAM mid 1 10 21.06 eFDD 7 16QAM mid 50 10 19.92 eFDD 7 QPSK mid 1 15 22.07 eFDD 7 QPSK mid 36 15 21.03 eFDD 7 QPSK mid 75 15 21.06 eFDD 7 16QAM mid 1 15 21.12 eFDD 7 16QAM mid 75 15 20.03 eFDD 7 QPSK mid 1 20 22.11 eFDD 7 QPSK mid 100 20 21.15 eFDD 7 16QAM mid 1 20 21.14 eFDD 7 16QAM mid 100 20 20.23 Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 12 of 28

4.1.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Frequency Band = eFDD7 QPSK 21100 20 MHz 1 RB, Channel = mid Marker 1 [T1] RBW 500 kHz RF Att 20 dB Ref Lvl 21.94 dBm VBW 2 MHz 36.5 dBm 2.53512024 GHz SWT 8.5 ms Unit dBm 36.5 26.5 dB Offset 1 [T1] 21.94 dBm A 30 2.53512024 GHz 1 CH PWR 22.11 dBm CH BW 18.04000000 MHz SGL 20 10 1VIEW 1RM 0 -10 EXT -20 -30 -40 -50 C0 C0 -60 -63.5 Start 2.515 GHz 4 MHz/ Stop 2.555 GHz Date: 10.JAN.2019 19:19:49 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 13 of 28

4.2 FIELD STRENGTH OF SPURIOUS RADIATION Standard FCC Part 2.1051 The test was performed according to: ANSI C63.26 4.2.1 TEST DESCRIPTION This test case is intended to demonstrate compliance to the applicable radiated spurious emission measurements per § 2.1053 The EUT was connected to the test setup according to the following diagram: The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software EMC32 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is also performed at 3 axes. A pre-check is performed while the EUT is powered from a DC power source. 1. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 14 of 28

- Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value - Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: Step 1: The Equipment Under Test (EUT) was set up on a non-conductive support (tilt device) at 1.5 m height in the fully-anechoic chamber. All steps were performed with one height (1.5 m) of the receiving antenna only. The EUT is turned during the preliminary measurement across the elevation axis, with a step size of 90 °. The turn table step size (azimuth angle) for the preliminary measurement is 45 °. Step 2: Due to the fact, that in this frequency range the test is performed in a fully anechoic room, the height scan of the receiving antenna instep 2 is omitted. Instead of this, a maximum search with a step size ± 45° for the elevation axis is performed. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 15 of 28

The turn table azimuth will slowly vary by ± 22.5°. The elevation angle will slowly vary by ± 45° EMI receiver settings (for all steps): - Detector: Peak, Average - IF Bandwidth = 1 MHz Step 3: Spectrum analyser settings for step 3: - Detector: Peak / Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 1 s 4.2.2 TEST REQUIREMENTS / LIMITS FCC Part 2.1051; Measurement required: Spurious emissions at antenna terminal: The radio frequency voltage or powers generated within the equipment and appearing on a spurious frequency shall be checked at the equipment output terminals when properly loaded with a suitable artificial antenna. Curves or equivalent data shall show the magnitude of each harmonic and other spurious emission that can be detected when the equipment is operated under the conditions specified in §2.1049 as appropriate. The magnitude of spurious emissions which are attenuated more than 20 dB below the permissible value need not be specified. Part 27, Subpart C – Technical Standards § 27.53m – Emission limits (4) For mobile digital stations, the attenuation factor shall be not less than 40 + 10 log (P) dB on all frequencies between the channel edge and 5 megahertz from the channel edge, 43 + 10 log (P) dB on all frequencies between 5 megahertz and X megahertz from the channel edge, and 55 + 10 log (P) dB on all frequencies more than X megahertz from the channel edge, where X is the greater of 6 megahertz or the actual emission bandwidth as defined in paragraph (m)(6) of this section. In addition, the attenuation factor shall not be less that 43 + 10 log (P) dB on all frequencies between 2490.5 MHz and 2496 MHz and 55 + 10 log (P) dB at or below 2490.5 MHz. Mobile Satellite Service licensees operating on frequencies below 2495 MHz may also submit a documented interference complaint against BRS licensees operating on channel BRS Channel 1 on the same terms and conditions as adjacent channel BRS or EBS licensees. (6) Measurement procedure. Compliance with these rules is based on the use of measurement instrumentation employing a resolution bandwidth of 1 megahertz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed; for mobile digital stations, in the 1 megahertz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least two percent may be employed, except when the 1 megahertz band is 2495-2496 MHz, in which case a resolution bandwidth of at least one percent may be employed. A narrower resolution bandwidth is permitted in all cases to improve measurement accuracy provided the measured power is integrated over the full required measurement bandwidth (i.e. 1 megahertz or 1 percent of emission bandwidth, as specified; or 1 megahertz or 2 percent for mobile digital stations, except in the band 2495-2496 MHz). The emission bandwidth is defined as the width TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 16 of 28

of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. With respect to television operations, measurements must be made of the separate visual and aural operating powers at sufficiently frequent intervals to ensure compliance with the rules. RSS-139; 6.6 Transmitter Unwanted Emissions (i) In the first 1.0 MHz bands immediately outside and adjacent to the equipment’s smallest operating frequency block,2 which can contain the equipment’s occupied bandwidth, the emission power per any 1% of the emission bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB. (ii) After the first 1.0 MHz outside the equipment’s smallest operating frequency block, which can contain the equipment’s occupied bandwidth, the emission power in any 1 MHz bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 17 of 28

4.2.3 TEST PROTOCOL eFDD 7, Test Frequency = mid Spurious Spurious Margin to Freq. Level RBW Limit Limit [MHz] [dBm] Detector [kHz] [dBm] [dB] - - - - -25.0 --- Remark: Please see next sub-clause for the measurement plot. COMMENT: No (further) spurious emissions in the range 20dB below the limit were found, therefore no measurement values are reported in the tables. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 18 of 28

4.2.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) Frequency Band = eFDD 7, Test Frequency = mid 30 MHz - 1 GHz 0 -5 -10 -15 -20 FCC_27.4_e FDD7 -25 -30 Level in dBm -35 -40 -45 -50 -55 -60 -65 -70 -75 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 1 GHz – 26 GHz 0 -10 -20 -30 -40 Level in dBm -50 -60 -70 -80 -90 -100 1G 2G 3G 4G 5G 6 8 10G 20G 26G Frequency in Hz 4.2.5 TEST EQUIPMENT USED - Radio Lab TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 19 of 28

5 TEST EQUIPMENT 1 Radio Lab FCC22/24/27 cond. Test Lab Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 FSIQ Spectrum Rohde & Schwarz 840061/005 2017-05 2019-05 Analyzer 1.2 WA1515 Broadband A856 Power Divider SMA 1.3 SMA Attenuator Coax Weinschel F9401 4T-10 Attenuator Associates 10dB SMA 2W 1.4 SMA Attenuator Coax Weinschel W3711 56-10 Attenuator Associates 10dB SMA 2W 1.5 Coax Cable Coax Cable Huber&Suhner - Sucotest 2.0m 1.6 Coax Cable Coax Cable Huber&Suhner - Sucotest SMA/SMA 1.0m 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2018-07 2019-07 2.2 MFS Rubidium Datum GmbH 002 2018-10 2020-10 Frequency Normal MFS 2.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 2.4 Anechoic 10.58 x 6.38 x Frankonia none 2016-05 2019-05 Chamber 6.00 m³ 2.5 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-07 2021-07 biconicals 2.6 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 2.7 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 2.8 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2018-06 2020-06 Room 4.60m x PRB 4.05m (l x w x h) 2.9 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 2.10 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 2.11 FSW 43 Spectrum Rohde & Schwarz 103779 2016-12 2018-12 Analyzer TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 20 of 28

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.12 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 2.13 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 2.14 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 2.15 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 2.16 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 2.17 TT 1.5 WI Turn Table Maturo GmbH - 2.18 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 2.19 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz 2.20 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 2.21 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2.22 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 2.23 ESR 7 EMI Receiver / Rohde & Schwarz 101424 2019-01 2021-01 Spectrum Analyzer 2.24 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 2.25 AS 620 P Antenna mast HD GmbH 620/37 2.26 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 2.27 ESIB 26 Spectrum Rohde & Schwarz 830482/004 Analyzer 2.28 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 2.29 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 2.30 HF 907 Double-ridged Rohde & Schwarz 102444 2018-07 2021-07 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 21 of 28

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 22 of 28

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 23 of 28

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 24 of 28

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 25 of 28

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 26 of 28

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -15.6 3 0.5 27.0 43.4 -11.2 4.4 -15.6 3 0.5 28.0 43.4 -11.1 4.5 -15.6 3 0.5 29.0 43.5 -11.0 4.6 -15.6 3 0.5 30.0 43.5 -10.9 4.7 -15.6 3 0.5 31.0 43.5 -10.8 4.7 -15.6 3 0.5 32.0 43.5 -10.7 4.8 -15.6 3 0.5 33.0 43.6 -10.7 4.9 -15.6 3 0.5 34.0 43.6 -10.6 5.0 -15.6 3 0.5 35.0 43.6 -10.5 5.1 -15.6 3 0.5 36.0 43.6 -10.4 5.1 -15.6 3 0.5 37.0 43.7 -10.3 5.2 -15.6 3 0.5 38.0 43.7 -10.2 5.3 -15.6 3 0.5 39.0 43.7 -10.2 5.4 -15.6 3 0.5 40.0 43.8 -10.1 5.5 -15.6 3 0.5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 27 of 28

7 MEASUREMENT UNCERTAINTIES Test Case(s) Parameter Uncertainty - Field strength of spurious radiation Power ± 5.5 dB - Out-of-band rejection Power ± 2.9 dB - Occupied Bandwidth Frequency ± 11.2 kHz - Input versus output spectrum - Effective radiated power, mean output Power ± 2.2 dB power and zone enhancer gain - Peak to Average Ratio - Out-of-band emission limits Power ± 2.2 dB - Conducted Spurious Emissions at Frequency ± 11.2 kHz Antenna Terminal 8 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCh_rev01 Page 28 of 28


Document Created: 2019-03-19 08:19:35
Document Modified: 2019-03-19 08:19:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC