MDE_UBLOX_1807_FCCd-FINAL-2019-02-21

FCC ID: XPYTOBYL201

Test Report

Download: PDF
FCCID_4217994

FCC Measurement/Technical Report on TOBY-L201 LTE/3G data only module FCC ID: XPYTOBYL201 IC: 8595A-TOBYL201 acc. to FCC Part 15 Subpart B Test Report Reference: MDE_UBLOX_1807_FCCd Test Laboratory: 7layers GmbH Borsigstrasse 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7layers GmbH Geschäftsführer/ Borsigstraße 11 Managing Directors: Registergericht/registered: a Bureau Veritas 40880 Ratingen, Germany Frank Spiller Düsseldorf HRB 75554 Group Company T +49 (0) 2102 749 0 Bernhard Retka USt-Id.-Nr./VAT-No. DE203159652 F +49 (0) 2102 749 350 Alexandre Norré-Oudard Steuer-Nr./TAX-No. 147/5869/0385 www.7layers.com Commerzbank AG Account No. 303 016 000 Bank Code 300 400 00 IBAN DE81 3004 0000 0303 0160 00 Swift Code COBADEFF

Table of Contents 1 Applied Standards and Test Summary 3 1.1 Applied Standards 3 1.2 FCC-IC Correlation Table 4 1.3 Measurement Summary / Signatures 4 2 Administrative Data 6 2.1 Testing Laboratory 6 2.2 Project Data 6 2.3 Applicant Data 6 2.4 Manufacturer Data 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 7 3.3 Ancillary Equipment 8 3.4 Auxiliary Equipment 8 3.5 EUT Setups 8 3.6 Operating Modes 9 3.7 Product labelling 9 4 Test Results 10 4.1 Conducted Emissions at AC mains 10 4.2 Radiated Emissions 13 5 Test Equipment 18 6 Antenna Factors, Cable Loss and Sample Calculations 21 6.1 LISN R&S ESH3-Z5 (150 kHz – 30 MHz) 21 6.2 Antenna R&S HFH2-Z2 (9 kHz – 30 MHz) 22 6.3 Antenna R&S HL562 (30 MHz – 1 GHz) 23 6.4 Antenna R&S HF907 (1 GHz – 18 GHz) 24 6.5 Antenna EMCO 3160-09 (18 GHz – 26.5 GHz) 25 6.6 Antenna EMCO 3160-10 (26.5 GHz – 40 GHz) 26 7 Setup Drawings 27 8 Measurement Uncertainties 28 9 Photo Report 28 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 2 of 28

1 APPLIED STANDARDS AND TEST SUMMARY 1.1 APPLIED STANDARDS Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-15 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart B – Unintentional Radiators § 15.107 Conducted limits § 15.109 Radiated emission limits; general requirements Note: ANSI C63.4–2014 is applied. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 3 of 28

Summary Test Results: The EUT complied with all performed tests as listed in chapter 1.3 Measurement Summary / Signatures. 1.2 FCC-IC CORRELATION TABLE Correlation of measurement requirements for Information Technology Equipment (ITE) from FCC and IC Measurement FCC reference IC reference Conducted Emissions §15.107 ICES-003 Issue 6: 6.1 (AC Power Line) Radiated Spurious Emissions §15.109 ICES-003 Issue 6: 6.2 Remarks: 1. FCC Part 15 subpart B, ICES 003 and CISPR 22 contain different definitions of Class A and Class B limits, i.e. which class is applicable to which kind of EUT. ICES 003 and CISPR 22 distinguish between the location where the EUT is intended to operate whilst FCC refers to the method of commercial distribution (distributive trades). 2. The correct assignment of the appropriate class to the concrete EUT is not scope of this test report! 3. A radio apparatus that is specifically subject to an Industry Canada Radio Standard Specification (RSS) and which contains an ITE is not subject to ICES-003 provided the ITE is used only to enable operation of the radio apparatus and the ITE does not control additional functions or capabilities. 4. ISM (Industrial, Scientific or Medical) radio frequency generators, though they may contain ITE, are excluded from the definition of ITE and are not subject to ICES-003. They are instead subject to the Interference-Causing Equipment Standard ICES-001, which specifically addresses ISM radio frequency generators. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 4 of 28

7Zlayers < A Bureau Veritas Group Company N WtU 1.3 MEASUREMENT SUMMARY / SIGNATURES 47 CFR CHAPTER I FCC PART 15 Subpart B § 15.107 Class B Conducted Emissions at AC mains The measurement was performed according to ANSI C63.4 Final Result OP—Mode Setup FCC IC AC mains connection, Test setup via auxiliary equipment, computer peripheric S01_ABO2 Passed Passed 47 CFR CHAPTER I FCC PART 15 Subpart B § 15.109 Class B Radiated Emissions The measurement was performed according to ANSI C63.4 Final Result OP—Mode Setup FCC IC AC mains connection, Measurement range, Test setup via auxiliary equipment, 1 GHz — 18 GHz, computer peripheric S01_ABO2 Passed Passed via auxiliary equipment, 30 MHz — 1 GHz, computer peripheric S01_ABO2 Passed Passed N/A: Not applicable N/P: Not performed L. |wL " (responsible for accreditation scope) Tbiout K res;fio?fsible for testing and report) Dipl.—Ing. Marco Kullik B.Sc. Jens Dorwald V Sorsigstr. 11 7 layers GmoH. 40880 Rati ng en , Germany Phone +49 (0)2102 749 0 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 5 of 28

2 ADMINISTRATIVE DATA 2.1 TESTING LABORATORY Company Name: 7layers GmbH Address: Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the ISED and accepted under the registration number: Site# 3699A-1. The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no: DAkkS D-PL-12140-01-00 FCC Designation Number: DE0015 FCC Test Firm Registration: 929146 Responsible for accreditation scope: Dipl.-Ing. Marco Kullik Report Template Version: 2018-01-10 2.2 PROJECT DATA Responsible for testing and report: B.Sc. Jens Dörwald Employees who performed the tests: documented internally at 7Layers Date of Report: 2019-02-21 Testing Period: 2018-12-21 to 2018-12-21 2.3 APPLICANT DATA Company Name: u-blox AG Address: Zürcherstrasse 68 CH-8800 Thalwil Switzerland Contact Person: Mr. Giulio Comar 2.4 MANUFACTURER DATA Company Name: please see Applicant Data Address: Contact Person: TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 6 of 28

3 TEST OBJECT DATA 3.1 GENERAL EUT DESCRIPTION Kind of Device LTE Module product description Product name TOBY-L201 LTE/3G data only module Type - Declared EUT data by the supplier Power Supply Type DC Nominal Voltage / INPUT: 120 V / 60 Hz Frequency OUTPUT: 3.8 V DC Test Voltage / INPUT: 120 V / 60 Hz Frequency OUTPUT: 3.8 V DC Highest internal 2600 MHz frequency General Description The EUT is a LTE Module. Ports DC USB Antenna Special software used - for testing The main components of the EUT are listed and described in chapter 3.2 EUT Main components. 3.2 EUT MAIN COMPONENTS Sample Name Sample Code Description ab02 ab02 Standard Sample Sample Parameter Value Serial No. 358502064213351 HW Version 218B01 SW Version v20.00 Comment - NOTE:The short description is used to simplify the identification of the EUT in this test report. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 7 of 28

3.3 ANCILLARY EQUIPMENT For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Device Details Description (Manufacturer, Type Model, OUT Code) - - - 3.4 AUXILIARY EQUIPMENT For the purposes of this test report, auxiliary equipment is defined as equipment which is used temporarily to enable operational and control features especially used for the tests of the EUT which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Device Details Description (Manufacturer, HW, SW, S/N) AUX1: AC/DC Adapter UNIFIVE UUX324-1215, -, -, J04- power supply for EUT 0543732 AUX2: LTE Antenna 1 Taoglas, -, -, - - AUX3: LTE Antenna 2 Taoglas, -, -, - - AUX4: Evaluation board Ublox EVB-WL3, - , - , - - AUX5: Monitor LG L17MB-P, -, -, 412 WAPL0U560 - AUX6: Laptop FUJITSU Ltd LIFEBOOK U758, 2018-07, - Win10 Pro, DSAL009842 AUX7: AC/ DC Adapter FUJITSU Ltd. A13-065N3A, -, -, power supply for Laptop 186905OL04 AUX8: Keyboard CHERRY RS6000 USB ON, -, -, G - 0000273 2P28 3.5 EUT SETUPS This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale S01_AB02 ab02 + AUX1 – AUX8 computer peripheral setup TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 8 of 28

3.6 OPERATING MODES This chapter describes the operating modes of the EUTs used for testing. LTE eFDD17 idle mode & USB traffic 3.6.1 TEST CHANNELS --- 3.7 PRODUCT LABELLING 3.7.1 FCC ID LABEL Please refer to the documentation of the applicant. 3.7.2 LOCATION OF THE LABEL ON THE EUT Please refer to the documentation of the applicant. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 9 of 28

4 TEST RESULTS 4.1 CONDUCTED EMISSIONS AT AC MAINS Standard FCC Part 15 Subpart B The test was performed according to: ANSI C63.4 4.1.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C 63.4 The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted emissions measurements in a typical installation configuration. The EUT was powered from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). The LISN’s unused connections were terminated with 50 Ohm loads. The measurement procedure consists of two steps. It is implemented into the EMI test software EMC-32 from R&S. Step 1: Preliminary scan Intention of this step is, to determine the conducted EMI-profile of the EUT. EMI receiver settings: - Detector: Peak – Maxhold & Average - Frequency range: 150 kHz – 30 MHz - Frequency steps: 2.5 kHz - IF–Bandwidth: 9 kHz - Measuring time / Frequency step: 100 ms (FFT-based) - Measurement on phase + neutral lines of the power cords On basis of this preliminary scan the highest amplitudes and the corresponding frequencies relative to the limit are identified. Emissions above the limit and emissions which are in the 10 dB range below the limit are considered. Step 2: Final measurement Intention of this step is, to determine the highest emissions with the settings defined in the test specification for the frequencies identified in step 1. EMI receiver settings: - Detector: Quasi-Peak - IF Bandwidth: 9 kHz - Measuring time: 1 s / frequency At each frequency determined in step 1, four measurements are performed in the following combinations: 1) Neutral lead - reference ground (PE grounded) 2) Phase lead - reference ground (PE grounded) 3) Neutral lead - reference ground (PE floating) 4) Phase lead - reference ground (PE floating) The highest value is reported. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 10 of 28

4.1.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart B, §15.107 Class B: Frequency (MHz) QP Limits (dBµV) AV Limits (dBµV) 0.15 – 0.5 66 - 56 56 - 46 0.5 - 5 56 46 5 - 30 60 50 Class A: Frequency (MHz) QP Limits (dBµV) AV Limits (dBµV) 0.15 – 0.5 79 66 0.5 - 30 73 60 4.1.3 TEST PROTOCOL Temperature: 23 °C Air Pressure: 996 hPa Humidity: 37 % Computer Peripheral Power line PE Frequency [MHz] Level [dBµV] Detector Limit [dBµV] Margin [dB] L1 FLO 0.42 41.8 QP 57.4 15.6 L1 GND 0.44 36.2 AV 47.1 10.8 Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 11 of 28

4.1.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) 150 kHz -30 MHz 80 70 L imit_ 1 5 _ 1 0 7 _ Q P _ Cla s sB 60 L imit_ 1 5 _ 1 0 7 _ A V _ Cla ss B 50 Level in dBµV 40 30 20 10 0 150k 3 0 0 4 0 05 0 0 8 0 01 M 2M 3M 4M 5M 6 8 10M 20M 30M F re q u e n c y in H z Frequency QuasiPeak CAverage Limit Margin Meas. Time Bandwidth Line PE Corr. (MHz) (dBµV) (dBµV) (dBµV) (dB) (ms) (kHz) (dB) 0.424500 41.81 --- 57.36 15.55 1000.0 9.000 L1 FLO 10.1 0.440250 --- 36.23 47.06 10.83 1000.0 9.000 L1 GND 10.1 4.1.5 TEST EQUIPMENT USED - Conducted Emissions FCC TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 12 of 28

4.2 RADIATED EMISSIONS Standard FCC Part 15 Subpart B The test was performed according to: ANSI C63.4 4.2.1 TEST DESCRIPTION The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used was evaluated. For the measurement above 1 GHz an absorber field with 30 cm pyramidical absorber is placed between EUT table and antenna (required to fulfil the CISPR 16.1.4 S-VSWR criteria). The measurement procedure is implemented into the EMI test software EMC32 from R&S. 1. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Quasipeak (FFT-based) - Frequency range: 30 – 1000 MHz - Frequency steps: 30 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 ms - Turntable angle range: –180° to 90° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 45° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 100 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 45 ° around the determined value - Height variation range: ± 100 cm around the determined value TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 13 of 28

- Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s 2. Measurement above 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold / Average (up to 7 GHz FFT-based) - Frequency range: 1 GHz – 18 GHz - Frequency steps: 250 kHz - IF–Bandwidth: 1 MHz - Measuring time / Frequency step: 100 ms (up to 7 GHz) / 500µs (above 7 GHz - Turntable angle range: –180° to 135° - Turntable step size: 45° - Height variation range: 1 – 3.7 m (due to the small antenna lobe, a tilt-mast is used) - Height variation step size: 0.9 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: Adjustment measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 22.5° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 45 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 100 ms - Turntable angle range: ± 22.5 ° around the determined value - Height variation range: ± 45 cm around the determined value - Antenna Polarisation: max. value determined in step 1 Step 3: Final measurement with Max-Peak / CISPR-Average detector With the settings determined in step 2, the final measurement will be performed: EMI receiver settings for step 3: - Detector: Max-Peak / CISPR-Average - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 1 MHz - Measuring time: 200 ms TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 14 of 28

After each measurement, a report will be generated which contains a diagram with the results of the preliminary scan and a table with the frequencies, values and polarisation of the results of the final measurement. 4.2.2 TEST REQUIREMENTS / LIMITS FCC Part 15, Subpart B, §15.109, Radiated Emission Limits Class B: Measurement Frequency (MHz) Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 100@3m 3 40.0@3m 88 – 216 150@3m 3 43.5@3m 216 – 960 200@3m 3 46.0@3m 960 - 26000 500@3m 3 54.0@3m 26000 - 40000 500@3m 1 54.0@3m Class A: Measurement Frequency (MHz) Limit (µV/m) Limits (dBµV/m) distance (m) 30 – 88 90@10m 3 39.1@10m 88 – 216 150@10m 3 43.5@10m 216 – 960 210@10m 3 46.4@10m 960 - 26000 300@10m 3 49.5@10m 26000 - 40000 300@10m 1 49.5@10m The measured values for Class A and for Class B (> 26 GHz) measurements are corrected with an inverse linear distance extrapolation factor (20 dB/decade). §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) 4.2.3 TEST PROTOCOL Ambient temperature: 23 °C Air Pressure: 996 hPa Humidity: 37 % Computer Peripheral Setup Spurious Freq. Spurious Level Detector RBW Limit Margin to Limit [MHz] [dBµV/m] [kHz] [dBµV/m] [dB] 32.9 39.4 QP 120 40.0 0.6 40.1 35.7 QP 120 40.0 4.3 75.6 34.4 QP 120 40.0 5.6 209.1 16.6 QP 120 43.5 26.9 216.0 19.2 QP 120 43.5 24.3 599.9 27.3 QP 120 46.0 18.7 5993.3 28.26 AV 1000 54.0 25.7 5999.0 54.47 PK 1000 74.0 19.5 Remark: Please see next sub-clause for the measurement plot. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 15 of 28

4.2.4 MEASUREMENT PLOT (SHOWING THE HIGHEST VALUE, “WORST CASE”) 30 MHz – 1 GHz 60 55 F CC _ 1 5 .1 0 9 _ Cla ss B @ 3 m _ 3 0 M H z -1 G H z 50 45 40 35 Level in dBµV/m 30 25 20 15 10 5 0 -5 30M 50 60 80 100M 200 300 400 500 800 1G F re q u e n c y in H z Frequency QuasiPeak Limit Margin Meas. Time Bandwidth Height Pol Azimuth Corr. (MHz) (dBµV/m) (dBµV/m) (dB) (ms) (kHz) (cm) (deg) (dB/m) 32.910000 39.43 40.00 0.57 1000.0 120.000 100.0 V -173.0 17.7 40.080000 35.73 40.00 4.27 1000.0 120.000 103.0 V -188.0 13.6 75.600000 34.38 40.00 5.62 1000.0 120.000 118.0 V 129.0 9.6 209.130000 16.58 43.50 26.92 1000.0 120.000 195.0 V -190.0 9.8 215.970000 19.22 43.50 24.28 1000.0 120.000 105.0 V -165.0 10.2 599.880000 27.34 46.00 18.66 1000.0 120.000 200.0 H -194.0 20.4 TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 16 of 28

1 GHz – 18 GHz 80 F CC _ 1 5 .1 0 9 _ Cla ss B @ 3 m _ 1 G H z -1 8 G H z _ P e a k 70 60 F CC _ 1 5 .1 0 9 _ Cla ss B @ 3 m _ 1 G H z -1 8 G H z _ A V 50 Level in dBµV/m 40 30 20 10 0 1G 2G 3G 4G 5G 6 8 10G 18G F re q u e n c y in H z Frequency MaxPeak CAverage Limit Margin Meas. Bandwidth Height Pol Azimuth Corr. (MHz) (dBµV/m) (dBµV/m) (dBµV/m) (dB) Time (kHz) (cm) (deg) (dB/m) (ms) 5993.250000 --- 28.26 54.00 25.74 200.0 1000.000 172.0 V 32.0 14.6 5999.000000 54.47 --- 74.00 19.53 200.0 1000.000 172.0 V 32.0 14.5 4.2.5 TEST EQUIPMENT USED - Radiated Emissions TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 17 of 28

5 TEST EQUIPMENT 1 Conducted Emissions FCC Conducted Emissions power line for FCC standards Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 1.1 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 1.2 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 1.3 ESH3-Z5 Two-Line V- Rohde & Schwarz 828304/029 2017-05 2019-05 Network 1.4 EP 1200/B, Amplifier with Spitzenberger & B6278 NA/B1 integrated Spieß variable Oscillator 1.5 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 1.6 Shielded Room Shielded Room Frankonia - 02 for conducted testing, 12qm 1.7 ESH3-Z5 Two-Line V- Rohde & Schwarz 829996/002 2017-05 2019-05 Network 1.8 ESR 7 EMI Receiver / Rohde & Schwarz 101424 Spectrum Analyzer 1.9 Opus10 THI ThermoHygro Lufft Mess- und 7489 2017-04 2019-04 (8152.00) Datalogger 02 Regeltechnik GmbH (Environ) 1.10 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 2 Radiated Emissions Lab to perform radiated emission tests Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.1 NRV-Z1 Sensor Head A Rohde & Schwarz 827753/005 2018-07 2019-07 GmbH & Co. KG 2.2 MFS Rubidium Datum GmbH 002 2018-10 2020-10 Frequency Normal MFS 2.3 Opus10 TPR ThermoAirpres Lufft Mess- und 13936 2017-04 2019-04 (8253.00) sure Regeltechnik GmbH Datalogger 13 (Environ) 2.4 ESW44 EMI Test Rohde & Schwarz 101603 2018-05 2019-05 Receiver GmbH & Co. KG 2.5 Anechoic 10.58 x 6.38 x Frankonia none 2018-06 2020-06 Chamber 6.00 m³ 2.6 FS-Z60 Harmonic Rohde & Schwarz 100178 2016-12 2019-12 Mixer 40 - 60 Messgerätebau GHz GmbH 2.7 FS-Z220 Harmonic Rohde & Schwarz 101005 2017-03 2020-03 Mixer 140 - Messgerätebau 220 GHz GmbH TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 18 of 28

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.8 SGH-05 Standard Gain RPG-Radiometer 075 / Pyramidal Physics GmbH Horn Antenna (140 - 220 GHz) 2.9 HL 562 Ultralog new Rohde & Schwarz 830547/003 2018-07 2021-07 biconicals 2.10 5HC2700/12750 High Pass Trilithic 9942012 -1.5-KK Filter 2.11 ASP 1.2/1.8-10 Antenna Mast Maturo GmbH - kg 2.12 Fully Anechoic 8.80m x Albatross Projects P26971-647-001- 2018-06 2020-06 Room 4.60m x PRB 4.05m (l x w x h) 2.13 Fluke 177 Digital Fluke Europe B.V. 86670383 2018-04 2020-04 Multimeter 03 (Multimeter) 2.14 NRVD Power Meter Rohde & Schwarz 828110/016 2018-07 2019-07 GmbH & Co. KG 2.15 HF 906 Double-ridged Rohde & Schwarz 357357/002 2018-09 2021-09 horn 2.16 JS4-18002600- Broadband Miteq 849785 32-5P Amplifier 18 GHz - 26 GHz 2.17 FSW 43 Spectrum Rohde & Schwarz 103779 Analyzer 2.18 3160-09 Standard Gain EMCO Elektronic 00083069 / Pyramidal GmbH Horn Antenna 26.5 GHz 2.19 SGH-19 Standard Gain RPG-Radiometer 093 / Pyramidal Physics GmbH Horn Antenna (40 - 60 GHz) 2.20 WHKX 7.0/18G- High Pass Wainwright 09 8SS Filter 2.21 4HC1600/12750 High Pass Trilithic 9942011 -1.5-KK Filter 2.22 Chroma 6404 AC Power Chroma ATE INC. 64040001304 Source 2.23 JS4-00102600- Broadband Miteq 619368 42-5A Amplifier 30 MHz - 26 GHz 2.24 TT 1.5 WI Turn Table Maturo GmbH - 2.25 HL 562 Ultralog Log.-per. Rohde & Schwarz 100609 2016-04 2019-04 Antenna 2.26 HF 906 Double-ridged Rohde & Schwarz 357357/001 2018-03 2021-03 horn 2.27 FS-Z325 Harmonic Rohde & Schwarz 101006 2017-03 2020-03 Mixer 220 - Messgerätebau 325 GHz GmbH 2.28 3160-10 Standard Gain EMCO Elektronic 00086675 / Pyramidal GmbH Horn Antenna 40 GHz TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 19 of 28

Ref.No. Device Name Description Manufacturer Serial Number Last Calibration Calibration Due 2.29 SGH-08 Standard Gain RPG-Radiometer 064 / Pyramidal Physics GmbH Horn Antenna (90 - 140 GHz) 2.30 SGH-12 Standard Gain RPG-Radiometer 326 / Pyramidal Physics GmbH HornAntenna (60 - 90 GHz) 2.31 5HC3500/18000 High Pass Trilithic 200035008 -1.2-KK Filter 2.32 FS-Z140 Harmonic Rohde & Schwarz 101007 2017-02 2020-02 Mixer 90 -140 Messgerätebau GHz GmbH 2.33 HFH2-Z2 Loop Antenna Rohde & Schwarz 829324/006 2018-01 2021-01 2.34 Opus10 THI ThermoHygro Lufft Mess- und 12482 2017-03 2019-03 (8152.00) Datalogger 12 Regeltechnik GmbH (Environ) 2.35 ESR 7 EMI Receiver / Rohde & Schwarz 101424 Spectrum Analyzer 2.36 JS4-00101800- Broadband Miteq 896037 35-5P Amplifier 30 MHz - 18 GHz 2.37 AS 620 P Antenna mast HD GmbH 620/37 2.38 Tilt device Antrieb TD1.5- Maturo GmbH TD1.5- Maturo 10kg 10kg/024/37907 (Rohacell) 09 2.39 SGH-03 Standard Gain RPG-Radiometer 060 / Pyramidal Physics GmbH Horn Antenna (220 - 325 GHz) 2.40 FS-Z90 Harmonic Rohde & Schwarz 101686 2017-03 2020-03 Mixer 60 - 90 Messgerätebau GHz GmbH 2.41 ESIB 26 Spectrum Rohde & Schwarz 830482/004 2018-01 2020-01 Analyzer 2.42 PAS 2.5 - 10 kg Antenna Mast Maturo GmbH - 2.43 AFS42- Broadband Miteq 2035324 00101800-25-S- Amplifier 25 42 MHz - 18 GHz 2.44 AM 4.0 Antenna mast Maturo GmbH AM4.0/180/1192 0513 2.45 HF 907 Double-ridged Rohde & Schwarz 102444 2018-07 2021-07 horn The calibration interval is the time interval between “Last Calibration” and “Calibration Due” TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 20 of 28

6 ANTENNA FACTORS, CABLE LOSS AND SAMPLE CALCULATIONS This chapter contains the antenna factors with their corresponding path loss of the used measurement path for all antennas as well as the insertion loss of the LISN. 6.1 LISN R&S ESH3-Z5 (150 KHZ – 30 MHZ) cable LISN loss insertion (incl. 10 loss dB ESH3- atten- Frequency Corr. Z5 uator) MHz dB dB dB 0.15 10.1 0.1 10.0 5 10.3 0.1 10.2 7 10.5 0.2 10.3 10 10.5 0.2 10.3 12 10.7 0.3 10.4 14 10.7 0.3 10.4 16 10.8 0.4 10.4 18 10.9 0.4 10.5 20 10.9 0.4 10.5 22 11.1 0.5 10.6 24 11.1 0.5 10.6 26 11.2 0.5 10.7 28 11.2 0.5 10.7 30 11.3 0.5 10.8 Sample calculation ULISN (dB µV) = U (dB µV) + Corr. (dB) U = Receiver reading LISN Insertion loss = Voltage Division Factor of LISN Corr. = sum of single correction factors of used LISN, cables, switch units (if used) Linear interpolation will be used for frequencies in between the values in the table. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 21 of 28

6.2 ANTENNA R&S HFH2-Z2 (9 KHZ – 30 MHZ) cable cable cable cable distance dLimit dused loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. AF (inside (outside (switch (to (-40 dB/ distance distance Frequency HFH-Z2) Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 0.009 20.50 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.01 20.45 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.015 20.37 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.02 20.36 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.025 20.38 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.03 20.32 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.05 20.35 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.08 20.30 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.1 20.20 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.2 20.17 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.3 20.14 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.49 20.12 -79.6 0.1 0.1 0.1 0.1 -80 300 3 0.490001 20.12 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.5 20.11 -39.6 0.1 0.1 0.1 0.1 -40 30 3 0.8 20.10 -39.6 0.1 0.1 0.1 0.1 -40 30 3 1 20.09 -39.6 0.1 0.1 0.1 0.1 -40 30 3 2 20.08 -39.6 0.1 0.1 0.1 0.1 -40 30 3 3 20.06 -39.6 0.1 0.1 0.1 0.1 -40 30 3 4 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 5 20.05 -39.5 0.2 0.1 0.1 0.1 -40 30 3 6 20.02 -39.5 0.2 0.1 0.1 0.1 -40 30 3 8 19.95 -39.5 0.2 0.1 0.1 0.1 -40 30 3 10 19.83 -39.4 0.2 0.1 0.2 0.1 -40 30 3 12 19.71 -39.4 0.2 0.1 0.2 0.1 -40 30 3 14 19.54 -39.4 0.2 0.1 0.2 0.1 -40 30 3 16 19.53 -39.3 0.3 0.1 0.2 0.1 -40 30 3 18 19.50 -39.3 0.3 0.1 0.2 0.1 -40 30 3 20 19.57 -39.3 0.3 0.1 0.2 0.1 -40 30 3 22 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 24 19.61 -39.3 0.3 0.1 0.2 0.1 -40 30 3 26 19.54 -39.3 0.3 0.1 0.2 0.1 -40 30 3 28 19.46 -39.2 0.3 0.1 0.3 0.1 -40 30 3 30 19.73 -39.1 0.4 0.1 0.3 0.1 -40 30 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -40 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 22 of 28

6.3 ANTENNA R&S HL562 (30 MHZ – 1 GHZ) (dLimit = 3 m) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. R&S (inside (outside (switch (to (-20 dB/ distance distance Frequency HL562 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) MHz dB (1/m) dB dB dB dB dB dB m m 30 18.6 0.6 0.29 0.04 0.23 0.02 0.0 3 3 50 6.0 0.9 0.39 0.09 0.32 0.08 0.0 3 3 100 9.7 1.2 0.56 0.14 0.47 0.08 0.0 3 3 150 7.9 1.6 0.73 0.20 0.59 0.12 0.0 3 3 200 7.6 1.9 0.84 0.21 0.70 0.11 0.0 3 3 250 9.5 2.1 0.98 0.24 0.80 0.13 0.0 3 3 300 11.0 2.3 1.04 0.26 0.89 0.15 0.0 3 3 350 12.4 2.6 1.18 0.31 0.96 0.13 0.0 3 3 400 13.6 2.9 1.28 0.35 1.03 0.19 0.0 3 3 450 14.7 3.1 1.39 0.38 1.11 0.22 0.0 3 3 500 15.6 3.2 1.44 0.39 1.20 0.19 0.0 3 3 550 16.3 3.5 1.55 0.46 1.24 0.23 0.0 3 3 600 17.2 3.5 1.59 0.43 1.29 0.23 0.0 3 3 650 18.1 3.6 1.67 0.34 1.35 0.22 0.0 3 3 700 18.5 3.6 1.67 0.42 1.41 0.15 0.0 3 3 750 19.1 4.1 1.87 0.54 1.46 0.25 0.0 3 3 800 19.6 4.1 1.90 0.46 1.51 0.25 0.0 3 3 850 20.1 4.4 1.99 0.60 1.56 0.27 0.0 3 3 900 20.8 4.7 2.14 0.60 1.63 0.29 0.0 3 3 950 21.1 4.8 2.22 0.60 1.66 0.33 0.0 3 3 1000 21.6 4.9 2.23 0.61 1.71 0.30 0.0 3 3 (dLimit = 10 m) 30 18.6 -9.9 0.29 0.04 0.23 0.02 -10.5 10 3 50 6.0 -9.6 0.39 0.09 0.32 0.08 -10.5 10 3 100 9.7 -9.2 0.56 0.14 0.47 0.08 -10.5 10 3 150 7.9 -8.8 0.73 0.20 0.59 0.12 -10.5 10 3 200 7.6 -8.6 0.84 0.21 0.70 0.11 -10.5 10 3 250 9.5 -8.3 0.98 0.24 0.80 0.13 -10.5 10 3 300 11.0 -8.1 1.04 0.26 0.89 0.15 -10.5 10 3 350 12.4 -7.9 1.18 0.31 0.96 0.13 -10.5 10 3 400 13.6 -7.6 1.28 0.35 1.03 0.19 -10.5 10 3 450 14.7 -7.4 1.39 0.38 1.11 0.22 -10.5 10 3 500 15.6 -7.2 1.44 0.39 1.20 0.19 -10.5 10 3 550 16.3 -7.0 1.55 0.46 1.24 0.23 -10.5 10 3 600 17.2 -6.9 1.59 0.43 1.29 0.23 -10.5 10 3 650 18.1 -6.9 1.67 0.34 1.35 0.22 -10.5 10 3 700 18.5 -6.8 1.67 0.42 1.41 0.15 -10.5 10 3 750 19.1 -6.3 1.87 0.54 1.46 0.25 -10.5 10 3 800 19.6 -6.3 1.90 0.46 1.51 0.25 -10.5 10 3 850 20.1 -6.0 1.99 0.60 1.56 0.27 -10.5 10 3 900 20.8 -5.8 2.14 0.60 1.63 0.29 -10.5 10 3 950 21.1 -5.6 2.22 0.60 1.66 0.33 -10.5 10 3 1000 21.6 -5.6 2.23 0.61 1.71 0.30 -10.5 10 3 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 23 of 28

6.4 ANTENNA R&S HF907 (1 GHZ – 18 GHZ) cable cable loss 3 loss 1 (switch (relay + cable unit, AF cable loss 2 atten- cable R&S inside (outside uator & loss 4 (to Frequency HF907 Corr. chamber) chamber) pre-amp) receiver) MHz dB (1/m) dB dB dB dB dB 1000 24.4 -19.4 0.99 0.31 -21.51 0.79 2000 28.5 -17.4 1.44 0.44 -20.63 1.38 3000 31.0 -16.1 1.87 0.53 -19.85 1.33 4000 33.1 -14.7 2.41 0.67 -19.13 1.31 5000 34.4 -13.7 2.78 0.86 -18.71 1.40 6000 34.7 -12.7 2.74 0.90 -17.83 1.47 7000 35.6 -11.0 2.82 0.86 -16.19 1.46 cable loss 4 cable (switch loss 1 cable cable unit, used AF (relay loss 2 loss 3 atten- cable for R&S inside (inside (outside uator & loss 5 (to FCC Frequency HF907 Corr. chamber) chamber) chamber) pre-amp) receiver) 15.247 MHz dB (1/m) dB dB dB dB dB dB 3000 31.0 -23.4 0.47 1.87 0.53 -27.58 1.33 4000 33.1 -23.3 0.56 2.41 0.67 -28.23 1.31 5000 34.4 -21.7 0.61 2.78 0.86 -27.35 1.40 6000 34.7 -21.2 0.58 2.74 0.90 -26.89 1.47 7000 35.6 -19.8 0.66 2.82 0.86 -25.58 1.46 cable loss 1 cable cable cable cable cable AF (relay loss 2 loss 3 loss 4 loss 5 loss 6 R&S inside (High (pre- (inside (outside (to Frequency HF907 Corr. chamber) Pass) amp) chamber) chamber) receiver) MHz dB (1/m) dB dB dB dB dB dB dB 7000 35.6 -57.3 0.56 1.28 -62.72 2.66 0.94 1.46 8000 36.3 -56.3 0.69 0.71 -61.49 2.84 1.00 1.53 9000 37.1 -55.3 0.68 0.65 -60.80 3.06 1.09 1.60 10000 37.5 -56.2 0.70 0.54 -61.91 3.28 1.20 1.67 11000 37.5 -55.3 0.80 0.61 -61.40 3.43 1.27 1.70 12000 37.6 -53.7 0.84 0.42 -59.70 3.53 1.26 1.73 13000 38.2 -53.5 0.83 0.44 -59.81 3.75 1.32 1.83 14000 39.9 -56.3 0.91 0.53 -63.03 3.91 1.40 1.77 15000 40.9 -54.1 0.98 0.54 -61.05 4.02 1.44 1.83 16000 41.3 -54.1 1.23 0.49 -61.51 4.17 1.51 1.85 17000 42.8 -54.4 1.36 0.76 -62.36 4.34 1.53 2.00 18000 44.2 -54.7 1.70 0.53 -62.88 4.41 1.55 1.91 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Tables show an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 24 of 28

6.5 ANTENNA EMCO 3160-09 (18 GHZ – 26.5 GHZ) cable cable cable cable cable AF loss 1 loss 2 loss 3 loss 4 loss 5 EMCO (inside (pre- (inside (switch (to Frequency 3160-09 Corr. chamber) amp) chamber) unit) receiver) MHz dB (1/m) dB dB dB dB dB dB 18000 40.2 -23.5 0.72 -35.85 6.20 2.81 2.65 18500 40.2 -23.2 0.69 -35.71 6.46 2.76 2.59 19000 40.2 -22.0 0.76 -35.44 6.69 3.15 2.79 19500 40.3 -21.3 0.74 -35.07 7.04 3.11 2.91 20000 40.3 -20.3 0.72 -34.49 7.30 3.07 3.05 20500 40.3 -19.9 0.78 -34.46 7.48 3.12 3.15 21000 40.3 -19.1 0.87 -34.07 7.61 3.20 3.33 21500 40.3 -19.1 0.90 -33.96 7.47 3.28 3.19 22000 40.3 -18.7 0.89 -33.57 7.34 3.35 3.28 22500 40.4 -19.0 0.87 -33.66 7.06 3.75 2.94 23000 40.4 -19.5 0.88 -33.75 6.92 3.77 2.70 23500 40.4 -19.3 0.90 -33.35 6.99 3.52 2.66 24000 40.4 -19.8 0.88 -33.99 6.88 3.88 2.58 24500 40.4 -19.5 0.91 -33.89 7.01 3.93 2.51 25000 40.4 -19.3 0.88 -33.00 6.72 3.96 2.14 25500 40.5 -20.4 0.89 -34.07 6.90 3.66 2.22 26000 40.5 -21.3 0.86 -35.11 7.02 3.69 2.28 26500 40.5 -21.1 0.90 -35.20 7.15 3.91 2.36 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 25 of 28

6.6 ANTENNA EMCO 3160-10 (26.5 GHZ – 40 GHZ) cable cable cable cable distance dLimit dused AF loss 1 loss 2 loss 3 loss 4 corr. (meas. (meas. EMCO (inside (outside (switch (to (-20 dB/ distance distance Frequency 3160-10 Corr. chamber) chamber) unit) receiver) decade) (limit) (used) GHz dB (1/m) dB dB dB dB dB dB m m 26.5 43.4 -11.2 4.4 -15.6 3 0.5 27.0 43.4 -11.2 4.4 -15.6 3 0.5 28.0 43.4 -11.1 4.5 -15.6 3 0.5 29.0 43.5 -11.0 4.6 -15.6 3 0.5 30.0 43.5 -10.9 4.7 -15.6 3 0.5 31.0 43.5 -10.8 4.7 -15.6 3 0.5 32.0 43.5 -10.7 4.8 -15.6 3 0.5 33.0 43.6 -10.7 4.9 -15.6 3 0.5 34.0 43.6 -10.6 5.0 -15.6 3 0.5 35.0 43.6 -10.5 5.1 -15.6 3 0.5 36.0 43.6 -10.4 5.1 -15.6 3 0.5 37.0 43.7 -10.3 5.2 -15.6 3 0.5 38.0 43.7 -10.2 5.3 -15.6 3 0.5 39.0 43.7 -10.2 5.4 -15.6 3 0.5 40.0 43.8 -10.1 5.5 -15.6 3 0.5 Sample calculation E (dB µV/m) = U (dB µV) + AF (dB 1/m) + Corr. (dB) U = Receiver reading AF = Antenna factor Corr. = sum of single correction factors of used cables, switch unit, distance correction, amplifier (if applicable) Linear interpolation will be used for frequencies in between the values in the table. distance correction = -20 * LOG (dLimit/ dused) Linear interpolation will be used for frequencies in between the values in the table. Table shows an extract of values. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 26 of 28

7 SETUP DRAWINGS _____________ Setup Drawings _____________ Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. LISN Analyzer Signaling EUT UNIT Setup in the shielded room for conducted measurements at AC mains port TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 27 of 28

8 MEASUREMENT UNCERTAINTIES Test Case Parameter Uncertainty Conducted Emissions at AC mains Voltage ± 3.4 dB Radiated Emissions Field Strength ± 5.5 dB 9 PHOTO REPORT Please see separate photo report. TEST REPORT REFERENCE: MDE_UBLOX_1807_FCCd Page 28 of 28


Document Created: 2019-02-21 10:34:51
Document Modified: 2019-02-21 10:34:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC